Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DISCHARGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Resonance hairpin and Langmuir probe-assisted laser photodetachment measurements of the negative ion density in a pulsed dc magnetron discharge

The time-resolved negative oxygen ion density n{sub -} close to the center line in a reactive pulsed dc magnetron discharge (10 kHz and 50% duty cycle) has been determined for the first time using a combination of laser photodetachment and resonance hairpin probing. The discharge was operated at a power of 50 W in 70% argon and 30% oxygen gas mixtures at 1.3 Pa pressure. The results show that the O{sup -} density remains pretty constant during the driven phase of the discharge at values typically below 5x10{sup 14} m{sup -3}; however, in the off-time, the O{sup -} density grows reaching values several times those in the on-time. This leads to the negative ion fraction (or degree of electronegativity) {alpha}=n{sub -}/n{sub e} being higher in the off phase (maximum value {alpha}{approx}1) than in the on phase ({alpha}=0.05-0.3). The authors also see higher values of {alpha} at positions close to the magnetic null than in the more magnetized region of the plasma. This fractional increase in negative ion density during the off-phase is attributed to the enhanced dissociative electron attachment of highly excited oxygen molecules in the cooling plasma. The results show that close to the magnetic null the photodetached electron density decays quickly after the laser pulse, followed by a slow decay over a few microseconds governed by the negative ion temperature. However, in the magnetized regions of the plasma, this decay is more gradual. This is attributed to the different cross-field transport rates for electrons in these two regions. The resonance hairpin probe measurements of the photoelectron densities are compared directly to photoelectron currents obtained using a conventional Langmuir probe. There is good agreement in the general trends, particularly in the off-time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental and numerical investigations of electron density in low-pressure dual-frequency capacitively coupled oxygen discharges

The electron density is measured in low-pressure dual-frequency (2/60 MHz) capacitively coupled oxygen discharges by utilizing a floating hairpin probe. The dependence of electron density at the discharge center on the high frequency (HF) power, low frequency (LF) power, and gas pressure are investigated in detail. A (1D) particle-in-cell/Monte Carlo method is developed to calculate the time-averaged electron density at the discharge center and the simulation results are compared with the experimental ones, and general agreements are achieved. With increasing HF power, the electron density linearly increases. The electron density exhibits different changes with the LF power at different HF powers. At low HF powers (e.g., 30 W in our experiment), the electron density increases with increasing LF power while the electron density decreases with increasing LF power at relatively high HF powers (e.g., 120 W in our experiment). With increasing gas pressure the electron density first increases rapidly to reach a maximum value and then decreases slowly due to the combined effect of the production process by the ionization and the loss processes including the surface and volume losses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma dynamics in a discharge produced by a pulsed dual frequency inductively coupled plasma source

Using a Langmuir probe, time resolved measurements of plasma parameters were carried out in a discharge produced by a pulsed dual frequency inductively coupled plasma source. The discharge was sustained in an argon gas environment at a pressure of 10 mTorr. The low frequency (P{sub 2} {sub MHz}) was pulsed at 1 kHz and a duty ratio of 50%, while high frequency (P{sub 13.56} {sub MHz}) was maintained in the CW mode. All measurements were carried out at the center of the discharge and 20 mm above the substrate. The results show that, at a particular condition (P{sub 2} {sub MHz} = 200 W and P{sub 13.56} {sub MHz }= 600 W), plasma density increases with time and stabilizes at up to ∼200 μs after the initiation of P{sub 2} {sub MHz} pulse at a plasma density of (2 × 10{sup 17} m{sup −3}) for the remaining duration of pulse “on.” This stabilization time for plasma density increases with increasing P{sub 2} {sub MHz} and becomes ∼300 μs when P{sub 2} {sub MHz} is 600 W; however, the growth rate of plasma density is almost independent of P{sub 2} {sub MHz}. Interestingly, the plasma density sharply increases as the pulse is switched off and reaches a peak value in ∼10 μs, then decreases for the remaining pulse “off-time.” This phenomenon is thought to be due to the sheath modulation during the transition from “pulse on” to “pulse off” and partly due to RF noise during the transition period. The magnitude of peak plasma density in off time increases with increasing P{sub 2} {sub MHz}. The plasma potential and electron temperature decrease as the pulse develops and shows similar behavior to that of the plasma density when the pulse is switched off.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Anomalous kinetic energy of a system of dust particles in a gas discharge plasma

The system of equations of motion of dust particles in a near-electrode layer of a gas discharge has been formulated taking into account fluctuations of the charge of a dust particle and the features of the nearelectrode layer of the discharge. The molecular dynamics simulation of the system of dust particles has been carried out. Performing a theoretical analysis of the simulation results, a mechanism of increasing the average kinetic energy of dust particles in the gas discharge plasma has been proposed. According to this mechanism, the heating of the vertical oscillations of dust particles is initiated by induced oscillations generated by fluctuations of the charge of dust particles, and the energy transfer from vertical to horizontal oscillations can be based on the parametric resonance phenomenon. The combination of the parametric and induced resonances makes it possible to explain an anomalously high kinetic energy of dust particles. The estimate of the frequency, amplitude, and kinetic energy of dust particles are close to the respective experimental values.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dynamics of the microstructure of current channels and the generation of high-energy electrons in nanosecond discharges in air

The results of the three-dimensional numerical simulation of the dynamics of the microstructure of high-voltage nanosecond discharges in air at atmospheric pressure are presented. It is established that the fast (at a time of ≈10 ns) broadening and significant decrease in the gas concentration in the microchannels occur as a result of the ohmic heating of microchannels with the diameter of 1–30 μm. It was shown that the broadening of microchannels in a nanosecond diffusive discharge provides an increase in the ratio of the electric field strength to the gas concentration in microchannels to values sufficient for the generation highenergy electron beams and X-ray bremsstrahlung in them. Features of the dynamics of the system of microchannels and its effect on the efficiency of the generation of high-energy electrons in discharges developing in the microstructuring regime of the current channels are considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A high-current rail-type gas switch with preionization by an additional corona discharge

The characteristics of a high-current rail-type gas switch with preionization of the gas (air) in a spark gap by an additional corona discharge are investigated. The experiments were performed in a voltage range of 10–45 kV using a two-electrode switch consisting of two cylindrical electrodes with a diameter of 22 mm and a length of 100 mm and a set of laterally located corona-discharge needles. The requirements for the position and size of the needles are defined for which a corona discharge is ignited before a breakdown of the main gap and does not change to a sparking form, and the entire length of the rail electrodes is efficiently used. The fulfillment of these requirements ensures stable operation of the switch with a small variation of the pulse breakdown voltage, which is not more than 1% for a fixed voltage-pulse rise time in the range from 150 ns to 3.5 μs. A short delay time of the switch breakdown makes it possible to control the two-electrode switch by an overvoltage pulse of nanosecond duration.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Numerical analysis of similarity of barrier discharges in the 0.95 Ne/0.05 Xe mixture

Established dynamic regimes of similar (with a scale factor of 10) barrier discharges in the 0.95 Ne/0.05 Xe mixture are simulated in a one-dimensional drift-diffusion model. The similarity is examined of barrier discharges excited in gaps of lengths 0.4 and 4 mm at gas pressures of 350 and 35 Torr and dielectric layer thicknesses of 0.2 and 2 mm, the frequencies of the 400-V ac voltage applied to the discharge electrodes being 100 and 10 kHz, respectively.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electron beam relaxation in nonuniform plasma of a steady-state beam-plasma discharge at moderately low gas pressures

Electron beam relaxation in plasma under conditions typical of laboratory plasma devices based on a steady-state beam-plasma discharge was investigated. It is shown that the measured dependences of the beam loss factor in a discharge operating at a moderately low gas pressure disagree with theoretical dependences calculated for a longitudinally uniform plasma. Analytic dependences obtained in the framework of quasilinear theory with allowance for longitudinal plasma inhomogeneity agree with experimental data. Some effects caused by the influence of the main discharge parameters on electron beam relaxation are analyzed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Concerning the width of spark channels with different polarities in submicrosecond sliding discharges in noble gases

Previously, the parameters of submicrosecond (with a duration of <200 ns) multichannel high-current discharges sliding along a ceramic surface in Ne, Ar, and Xe were studied only for the negative polarity of the applied voltage. The experimental data indicate that the channels expand in the transverse direction mainly due to electron drift from the channel surface layer under the action of the electric field perpendicular to the channel axis and subsequent gas ionization by these electrons. To investigate mechanisms for the channel development in a sliding discharge-in particular, to determine the contribution of electron drift-it is necessary to carry out experiments similar to those performed earlier for the opposite polarity of the applied voltage. Here, the results of measurements of the widths of the spark channels of negativeand positive-polarity sliding discharges excited in Ne, Ar, and Xe at pressures of 30 and 100 kPa are presented and discussed. It is shown that, depending on the pressure and sort of gas, the averaged optical width of positive-polarity channels is smaller by a factor of 1.27-1.60 than that of negative-polarity channels. The experimental data are analyzed using the theory of propagation of ionization waves with different polarities in gases. Analysis has shown that electron diffusion contributes insignificantly to channel expansion and that, for both polarities, the channel expansion rate exceeds the electron drift velocity in the transverse electric field near the channel. In the framework of the so-called approximation of nonlocalized initial conditions, the measured ratio between of the widths of negativeand positive-polarity channels and their relation to the electron mobility are explained by the channel expansion governed by both electron drift and primary free electrons produced by a short-term source in a narrow region ahead of the front of the expansion wave. Numerical simulations show that the width of this region is comparable with that of the wave front and is more than one order of magnitude smaller than the observed channel radius. Gas photoionization by the channel radiation can serve as a source of primary electrons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ion flux onto conducting and isolated surfaces in the beam-plasma discharge: Computer simulation

A physical model which allows the use of the program code KARAT for simulating the quasisteady state of the beam-plasma discharge with plasma regeneration from a neutral gas is developed. The results of simulation of the modes of discharge at different potentials at the discharge collector are reported. The results obtained for isolated and grounded ion collectors are compared.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of the optical properties of a pulse-periodic high-pressure cesium discharge

Results of theoretical and experimental studies of the optical spectrum of a pulse-periodic high-pressure cesium discharge are presented. The results of calculations are in good agreement with experimental data. The possibility of creating an efficient light source based on recombination emission from the discharge plasma is demonstrated. The formation mechanisms of the continuous spectrum of discharge radiation are considered.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Strong localized interaction of microplasma discharges with titanium

Excitation of microplasma discharges on the surfaces of titanium samples placed in a uniform pulsed plasma flow was studied experimentally. Strong localized interaction of microplasma discharges with titanium leads to the rapid melting and subsequent fast cooling of micrometer-size regions on the sample surface. Due to the multiple action of microplasma discharges, a continuous remelted layer with a thickness of up to 20 {mu}m forms on the titanium surface. The physical, structural, and tribotechnical properties of this layer differ substantially from those before microplasma processing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Non-self-sustained glow discharge with electrostatic confinement of electrons sustained by a fast neutral molecule beam

Experimental study of plasma produced at the nitrogen pressure 0.2-1 Pa in the chamber volume V Almost-Equal-To 0.12 m{sup 3} as a result of injection into the chamber of a broad nitrogen molecule beam with 1-4 keV energy and 0.1-1 A equivalent current is carried out, and the study results are presented. Dependences of the plasma density distribution on the beam equivalent current I{sub b}, energy E{sub b}, and gas pressure p indicate a crucial role of fast molecules in gas ionization, and the probe characteristics reveal two groups of plasma electrons with the temperatures T{sub e} {approx} 0.4 eV and T{sub e} {approx} 16 eV. Immersion in plasma of an electrode isolated from the chamber and application to the electrode of a positive voltage U result in non-self-sustained discharge. When U changes from {approx}0.5 to {approx}1.5 V, the discharge current I rapidly rises to a certain value I*, and after that the rate of rise dI/dU drops by an order of magnitude. At U {approx} 10 V, the current I rises to I{sub 0} Almost-Equal-To 1.5I*, and dI/dU once again drops by an order of magnitude. Current I{sub 0} specifies the number of electrons produced inside the chamber per second, and it grows up with E{sub b}, I{sub b}, and p. At U > 20 V, due to gas ionization by fast electrons emitted by the chamber and accelerated up to the energy {approx}eU in the sheath between the plasma and the chamber walls, the current I rises again. When U grows up to {approx}50 V, production of fast electrons with energies exceeding the ionization threshold begins inside the sheath, and the ionization intensity rises dramatically. At U > 150 V, contribution of fast electrons to gas ionization already exceeds the contribution of fast molecules, and the plasma density and its distribution homogeneity inside the chamber both grow up substantially. However, even in this case, the discharge is non-self-sustained, and only at U > 300 V it does not expire when the beam source is switched off.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of microplasma discharges on aluminum surfaces

Excitation of microplasma discharges on the surfaces of V95 aluminum alloy samples placed in a uniform pulsed plasma flow was studied experimentally. Strong localized interaction of microplasma discharges with aluminum leads to the melting and subsequent fast cooling of micrometer-size regions on the sample surface. Due to the multiple action of microplasma discharges, a continuous remelted layer with a thickness of up to 20 {mu}m forms on the aluminum surface. The physical, structural, and tribotechnical properties of this layer differ substantially from those before microplasma processing.

36 MATERIALS SCIENCE↗

Control of power characteristics of ion flow in plasma-etching reactor based on beam-plasma discharge

It is shown that on the basis of the earlier revealed effect of generating the ion flow in the beam-plasma discharge from the discharge axis, a plasma processing reactor can be created for low-energy etching of semiconductor structures. The possibility of easily controlling the density and energy of ion flow by means of varying the potential of the discharge collector is demonstrated. The charge compensation of the ion flow incident on the nonconducting surface is implemented using the modulation of the potential of the substrate holder as well as the plasma-potential modulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Kinetic processes initiated by a nanosecond high-current discharge in hot air

Results from numerical investigations of kinetic processes initiated by a pulsed nanosecond discharge in hot (T{sub 0} {>=} 1000 K) air at atmospheric pressure are presented. The calculated results on the dynamics of the electron density, the population of the N{sub 2}(B{sup 3}{Pi}{sub g}) and N{sub 2}(C{sup 3}{Pi}{sub u}) states, and the atomic oxygen density in the axial discharge region agree with experiment. The method for determining the gas temperature by measuring the rotational structure of the transitions N{sub 2}(C{sup 3}{Pi}{sub u}, {nu}) {yields} N{sub 2}(B{sup 3}{Pi}{sub g}, {nu} Prime ) of the 2{sup +} nitrogen system is analyzed. It is shown that, in relatively weak reduced electric fields typical of secondary discharge pulses, the electron impact excitation of the N{sub 2}(C{sup 3}{Pi}{sub u}) state from the ground state N{sub 2}(X{sup 1}{Sigma}{sub g}{sup +}) can be accompanied by its additional step population from the N{sub 2}(B{sup 3}{Pi}{sub g}), N{sub 2}(a Prime {Sigma}{sub u}{sup -}), and other electronic states. This effect substantially influences the rotational distribution of nitrogen molecules in the N{sub 2}(C{sup 3}{Pi}{sub u}, {nu}) state; moreover, the temperature determined from this distribution can be substantially higher than the true gas temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of the barrier discharge structure near the electrode with a cylindrical cross section

The approximate analytical correlations allowing for the investigation of the effect of different geometrical and physical parameters on the barrier discharge evolution near the electrode with a cylindrical cross section are obtained. The found correlations make it possible to estimate the time of the barrier discharge existence. New essential peculiarities of the barrier discharge evolution are revealed and verified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Peculiarities of the beam-plasma discharge development in high-pressure gas and prospects of its application

The dynamics of a stationary beam-plasma discharge at the neutral gas pressure of 10{sup -3}-1 Torr is investigated. Three discharge modes have been revealed: two of them are characterized by novel properties and have not been studied as of yet. Dissipative instabilities with different increments have been found. The generation of ion flows has been studied and the experiments on 'dry' cleaning of the metal specimen surfaces using them have been carried out. The pressure ranges in a neutral gas at which the discharge can be efficiently applied in nonequilibrium plasma chemistry are given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗