Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Dynamic characteristics of the national full-scale aerodynamic complex drive fan blades

An extensive experimental test program was conducted to define the dynamic characteristics of the newly installed fan blades of the NASA Ames 40- by 80-/80- by 120-Foot Wind Tunnel. The tests were intended to substantiate the blade design and manufacturing process, verify installation integrity, and guarantee safe fan-drive operation. The program included a shake test of each fan blade after installation and before operation as well as the monitoring of blade strain levels during initial operation. Structural characteristics, as determined by the shake test, include the modal frequency and damping values for elastic bending and torsion modes between 5 and 130 Hz. Operational testing defined the maximum and oscillatory blade-bending strains throughout the drive-system operational envelope. Results are presented for the shake test and initial operation of the 40- by 80-Foot Wind Tunnel circuit.

Peterson, Randall L.↗
NASA NTRS1987

The effect of nonlinear elastomeric lag damper characteristics on helicopter rotor dynamics

Many helicopters use elastomeric lag dampers to prevent ground resonance and aeromechanical instability in hover and forward flight. Recent experimental results have shown that when the damper motion occurs at two superimposed frequencies, which is characteristic of operation in forward flight, the damper properties are not well-predicted by a superposition of the damper properties at each of the motion frequencies. This paper presents experimental data obtained with an elastomeric damper while it was undergoing single- and dual-frequency motion. The effect of the nonlinear dual-frequency damper characteristics on predicted rotor aeromechanical stability in forward-flight operation in a wind tunnel was evaluated using the comprehensive rotorcraft analysis program called CAMRAD.

Felker, Fort F.↗
NASA NTRS1987

Two-dimensional nozzle plume characteristics

Future high performance aircraft will likely feature asymmetric or two-dimensional nozzles with or without ejectors. In order to design two-dimensional nozzle/ejector systems of minimum size and weight, the plume decay and spreading characteristics of basic two-dimensional nozzles must first be established. The present work deals with the experimental analyses of these plume characteristics and includes the effects of nozzle aspect ratio and flow conditions (jet Mach number and temperature) on the plume decay and spreading of two-dimensional nozzles. Correlations including these variables are developed in a manner similar to those previously developed successfully for conic and dual-flow plumes.

Von Glahn, Uwe H.↗
NASA NTRS1987

On the nonlinear aerodynamic and stability characteristics of a generic chine-forebody slender-wing fighter configuration

An exploratory investigation was conducted of the nonlinear aerodynamic and stability characteristics of a tailless generic fighter configuration featuring a chine-shaped forebody coupled to a slender cropped delta wing in the NASA Langley Research Center's 12-Foot Low-Speed Wind Tunnel. Forebody and wing vortex flow mechanisms were identified through off-body flow visualizations to explain the trends in the longitudinal and lateral-directional characteristics at extreme attitudes (angles of attack and sideslip). The interactins of the vortical motions with centerline and wing-mounted vertical tail surfaces were studied and the flow phenomena were correlated with the configuration forces and moments. Single degree-of-freedom, free-to-roll tests were used to study the wing rock susceptibility of the generic fighter model. Modifications to the nose region of the chine forebody were examined and fluid mechanisms were established to account for their ineffectiveness in modulating the highly interactive forebody and wing vortex systems.

Erickson, Gary E.↗
NASA NTRS1987

Characteristics of a separating confluent boundary layer and the downstream wake

Measurements of pressure and velocity characteristics are presented and analyzed for flow over and downstream of a NACA 4412 airfoil equipped with a NACA 4415 single-slotted flap at high angle of attack and close to maximum lift. The flow remained attached over the main element while a large region of recirculating flow occurred over the aft 61 percent of the flap. The airfoil configuration was tested at a Mach number of 0.09 and a chord Reynolds number of 1.8x10 to the 6th power in the NASA Ames Research Center 7- by 10-Foot Wind Tunnel. Measurement of mean and fluctuation velocities were obtained in regions of recirculation and high turbulence intensity using 3-D laser velocimetry. In regions where the flow had a preferred direction and relatively low turbulence intensity, hot-wire anemometry was used. Emphasis was placed on obtaining characteristics in the confluent boundary layer, the region of recirculating flow, and in the downstream wake. Surface pressure measurements were made on the main airfoil, flap, wind tunnel roof and floor. It is thought likely that because the model is large when compared to the wind tunnel cross section, the wind tunnel floor and ceiling interference should be taken into account when the flow field is calculated.

Adair, Desmond↗
NASA NTRS1986

General equilibrium characteristics of a dual-lift helicopter system

The equilibrium characteristics of a dual-lift helicopter system are examined. The system consists of the cargo attached by cables to the endpoints of a spreader bar which is suspended by cables below two helicopters. Results are given for the orientation angles of the suspension system and its internal forces, and for the helicopter thrust vector requirements under general circumstances, including nonidentical helicopters, any accelerating or static equilibrium reference flight condition, any system heading relative to the flight direction, and any distribution of the load to the two helicopters. Optimum tether angles which minimize the sum of the required thrust magnitudes are also determined. The analysis does not consider the attitude degrees of freedom of the load and helicopters in detail, but assumes that these bodies are stable, and that their aerodynamic forces in equilibrium flight can be determined independently as functions of the reference trajectory. The ranges of these forces for sample helicopters and loads are examined and their effects on the equilibrium characteristics are given parametrically in the results.

Cicolani, L. S.↗
NASA NTRS1988

Reinforcing of thermoplastic polycarbonate and polysulfone with carbon fibers: Production and characteristics of UD-compound objects

The production and characteristics of the carbon fiber reinforced thermoplastics polycarbonate and polysulfone are described. The production of prepregs from defined polymer solutions is emphasized along with methods of optimizing the production of compounds. The characteristics of unidirectionally reinforced thermoplastics, such as shear strength, bending strength, and impact resistance are compared with regard to fracture behavior, the influence of intermediate layers, and the behavior under cryogenic conditions and under slightly elevated temperatures. The problem of adhesion between high strength carbon fibers and thermoplastics is examined, taking into account the effect of moisture on the shear strength and the impact resistance.

Fitzer, E.↗
NASA NTRS1988

Shape sensitivity analysis of wing static aeroelastic characteristics

A method is presented to calculate analytically the sensitivity derivatives of wing static aeroelastic characteristics with respect to wing shape parameters. The wing aerodynamic response under fixed total load is predicted with Weissinger's L-method; its structural response is obtained with Giles' equivalent plate method. The characteristics of interest include the spanwise distribution of lift, trim angle of attack, rolling and pitching moments, wind induced drag, as well as the divergence dynamic pressure. The shape parameters considered are the wing area, aspect ratio, taper ratio, sweep angle, and tip twist angle. Results of sensitivity studies indicate that: (1) approximations based on analytical sensitivity derivatives can be used over wide ranges of variations of the shape parameters considered, and (2) the analytical calculation of sensitivity derivatives is significantly less expensive than the conventional finite-difference alternative.

Barthelemy, Jean-Francois M.↗
NASA NTRS1988

Two-Equation Low-Reynolds-Number Turbulence Modeling of Transitional Boundary Layer Flows Characteristic of Gas Turbine Blades

The use of low Reynolds number (LRN) forms of the k-epsilon turbulence model in predicting transitional boundary layer flow characteristic of gas turbine blades is developed. The research presented consists of: (1) an evaluation of two existing models; (2) the development of a modification to current LRN models; and (3) the extensive testing of the proposed model against experimental data. The prediction characteristics and capabilities of the Jones-Launder (1972) and Lam-Bremhorst (1981) LRN k-epsilon models are evaluated with respect to the prediction of transition on flat plates. Next, the mechanism by which the models simulate transition is considered and the need for additional constraints is discussed. Finally, the transition predictions of a new model are compared with a wide range of different experiments, including transitional flows with free-stream turbulence under conditions of flat plate constant velocity, flat plate constant acceleration, flat plate but strongly variable acceleration, and flow around turbine blade test cascades. In general, calculational procedure yields good agreement with most of the experiments.

Schmidt, Rodney C.↗
NASA NTRS1986

Acoustic characteristics of 1/20-scale model helicopter rotors

A wind tunnel test to study the effects of geometric scale on acoustics and to investigate the applicability of very small scale models for the study of acoustic characteristics of helicopter rotors was conducted in the United Technologies Research Center Acoustic Research Tunnel. The results show that the Reynolds number effects significantly alter the Blade-Vortex-Interaction (BVI) Noise characteristics by enhancing the lower frequency content and suppressing the higher frequency content. In the time domain this is observed as an inverted thickness noise impulse rather than the typical positive-negative impulse of BVI noise. At higher advance ratio conditions, in the absence of BVI, the 1/20 scale model acoustic trends with Mach number follow those of larger scale models. However, the 1/20 scale model acoustic trends appear to indicate stall at higher thrust and advance ratio conditions.

Shenoy, Rajarama K.↗
NASA NTRS1988

Neutron effects on the electrical and switching characteristics of NPN bipolar power transistors

The use of nuclear reactors to generate electrical power for future space missions will require the electrical components used in the power conditioning, control, and transmission subsystem to operate in the associated radiation environments. An initial assessment of neutron irradiation on the electrical and switching characteristics of commercial high power NPN bipolar transistors was investigated. The results clearly show the detrimental effects caused by neutron irradiation on the electrical and switching characteristics of the NPN bipolar power transistor.

Frasca, Albert J.↗
NASA NTRS1988

Characteristics of merging shear layers and turbulent wakes of a multi-element airfoil

Flow characteristics in the vicinity of the trailing edge of a single-slotted airfoil flap are presented and analyzed. The experimental arrangement consisted of a NACA 4412 airfoil equipped with a NACA 4415 flap whose angle of deflection was 21.8 deg. The flow remained attached over the model surfaces except in the vicinity of the flap trailing edge where a small region of boundary-layer separation extended over the aft 7 percent of flap chord. The flow was complicated by the presence of a strong, initially inviscid jet emanating from the slot between airfoil and flap, and a gradual merging of the main airfoil wake and flap suction-side boundary layer. Downstream of the flap, the airfoil and flap wakes fully merged to form an asymmetrical curved wake. The airfoil configuration was tested at an angle of attack of 8.2 deg, at a Mach number of 0.09, and a chord based Reynolds number of 1.8 x 10 to the 6th power in the Ames Research Center 7- by 10-Foot Wind Tunnel. Surface pressure measurements were made on the airfoil and flap and on the wind tunnel roof and floor. It was estimated that the wall interference increased the C sub L by 7 percent and decreased the C sub M by 4.5 percent. Velocity characteristics were quantified using hot-wire anemometry in regions of flow with preferred direction and low turbulence intensity. A 3-D laser velocimeter was used in regions of flow recirculation and relatively high turbulence intensity.

Adair, Desmond↗
NASA NTRS1988

Effects of independent variation of Mach and Reynolds numbers on the low-speed aerodynamic characteristics of the NACA 0012 airfoil section

A comprehensive data base is given for the low speed aerodynamic characteristics of the NACA 0012 airfoil section. The Langley low-turbulence pressure tunnel is the facility used to obtain the data. Included in the report are the effects of Mach number and Reynolds number and transition fixing on the aerodynamic characteristics. Presented are also comparisons of some of the results with previously published data and with theoretical estimates. The Mach number varied from 0.05 to 0.36. The Reynolds number, based on model chord, varied from 3 x 10 to the 6th to 12 x 10 to the 6th power.

Ladson, Charles L.↗
NASA NTRS1988

Calculation of aerodynamic characteristics of airplane configurations at high angles of attack

Calculation of longitudinal and lateral directional aerodynamic characteristics of airplanes by the VORSTAB code is examined. The numerical predictions are based on the potential flow theory with corrections of high angle of attack phenomena; namely, vortex flow and boundary layer separation effects. To account for the vortex flow effect, vortex lift, vortex action point, augmented vortex lift and vortex breakdown effect through the method of suction analogy are included. The effect of boundary layer separation is obtained by matching the nonlinear section data with the three dimensional lift characteristics iteratively. Through correlation with results for nine fighter configurations, it is concluded that reasonably accurate prediction of longitudinal and static lateral directional aerodynamics can be obtained with the VORSTAB code up to an angle of attack at which wake interference and forebody vortex effect are not important. Possible reasons for discrepancy at higher angles of attack are discussed.

Tseng, J. B.↗
NASA NTRS1987

Evidence for divergent plate-boundary characteristics and crustal spreading on Venus

Detailed examination of the topography and morphology of western Aphrodite Terra reveals numerous features that are similar to terrestrial divergent plate-boundary characteristics. Individual domains between fracture-zone-like discontinuities contain a variety of bilaterally symmetrical topographic elements that suggest that topographic features have been created at rise crests, rifted and separated, and moved laterally to their present symmetrical positions. The topographic and morphologic similarities, together with strikingly similar mirror-image map patterns on both sides of the rise axis, suggest that western Aphrodite Terra shares the characteristics of oceanic divergent plate boundaries, and is the site of crustal spreading on Venus. Topographic profiles are consistent with spreading rates of the order of several centimeters per year.

Head, James W., III↗
NASA NTRS1987

Unusual characteristics of electromagnetic waves excited by cometary newborn ions with large perpendicular energies

The characteristics of electromagnetic waves excited by cometary newborn ions with large perpendicular energies are examined using a model of solar wind permeated by dilute drifting ring distributions of electrons and oxygen ions with finite thermal spreads. The model has parameters compatible with the ICE observations at the Giacobini-Zinner comet. It is shown that cometary newborn ions with large perpendicular energies can excite a wave mode with rest frame frequencies in the order of the heavy ion cyclotron frequency, Omega(i), and unusual propagation characteristics at small obliquity angles. For parallel propagation, the mode is left-hand circularly polarized, might be unstable in a frequency range containing Omega(i), and moves in the direction of the newborn ion drift along the static magnetic field.

Brinca, A. L.↗
NASA NTRS1988

Shape sensitivity analysis of wing static aeroelastic characteristics

A method is presented to calculate analytically the sensitivity derivatives of wing static aeroelastic characteristics with respect to wing shape parameters. The wing aerodynamic response under fixed total load is predicted using Weissinger's L-method; its structural response is obtained with Giles' equivalent plate method. The characteristics of interest in this study include the spanwise distribution of lift, trim angle of attack, rolling and pitching moments, wing induced drag as well as the divergence dynamic pressure. The shape parameters considered are the wing area, aspect ratio, taper ratio, sweep angle and tip twist angle. Results of sensitivity studies indicate that (1) approximations based on analytical sensitivity derivatives can be used for wide ranges of variations of the shape parameters considered and (2) the analytical calculation of sensitivity derivatives is significantly less expensive than the conventional finite difference alternative.

Barthelemy, Jean-Francois M.↗
NASA NTRS1988

Effects of symmetric and asymmetric modes on transonic aeroelastic characteristics of full-span wing-body configurations

To accurately study the transonic aeroelastic characteristics, it is important to model the full aircraft configuration, including asymmetry. Recently, an accurate method of computing unsteady transonic flows on full-span wing-body configurations was developed using the transonic potential flow theory. In this work, the method is further developed to account for the aeroelasticity of full-span wing-body configurations. This is accomplished by simultaneously integrating the unsteady aerodynamic forces and modal structural equations of the wing-body configurations. To validate the method, aeroelastic computations are made for a wing-body configuration with a rectangular wing. The aeroelastic responses of this configuration are correlated with the responses of a similar isolated wing. The comparisons are favorable. Aeroelastic computations associated with symmetric and asymmetric modes are also made to study the influence of modal asymmetry on responses. This new development is further illustrated by computing aeroelastic characteristics of a typical fighter aircraft. The results from this study will be useful in accurately computing the transonic flutter boundaries of aircraft, including those associated with asymmetric modes.

Guruswamy, Guru P.↗