Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CREEP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Fatigue retardation due to creep in a fibrous composite

Experiments performed to determine the effects of temperature and creep strain on the fatigue life of a graphite/epoxy composite laminate show that (1) sustained periods of static loading have significant retardation effects on the fatigue degradation rate of the laminated composite, and (2) cyclic loading with a lower frequency preceding higher frequency loading also prolongs the fatigue life. A creep crack hypothesis is proposed that can provide reasonable interpretations for these experimental results.

Sun, C. T.↗
NASA NTRS1981

Creep rupture of polymer-matrix composites

The time-dependent creep-rupture process in graphite-epoxy laminates is examined as a function of temperature and stress level. Moisture effects are not considered. An accelerated characterization method of composite-laminate viscoelastic modulus and strength properties is reviewed. It is shown that lamina-modulus master curves can be obtained using a minimum of normally performed quality-control-type testing. Lamina-strength master curves, obtained by assuming a constant-strain-failure criterion, are presented along with experimental data, and reasonably good agreement is shown to exist between the two. Various phenomenological delayed failure models are reviewed and two (the modified rate equation and the Larson-Miller parameter method) are compared to creep-rupture data with poor results.

Brinson, H. F.↗
NASA NTRS1980

Thermomechanical processing of Haynes alloy No. 188 sheet to improve creep strength

A study has been carried out with the objective of improving the low-strain creep strength of thin gauge (0.38 mm) sheet of Haynes alloy No. 188, a candidate material for the heat shields of advanced reentry and hypersonic vehicles. It is found that significant improvements in the low-strain creep strength are obtained in sheets with a strong recrystallized texture produced by a thermomechanical treatment. The optimum results are achieved after 80% final coldwork followed by a 10-min anneal at 1505 K.

Klarstrom, D. L.↗
NASA NTRS1981

Creep recovery and stress relaxation tests of 6061-0 aluminum

The investigation of creep recovery and stress relaxation in aluminum using a closed loop servo-hydraulic test system is described. The practicality of a computer controlled test system for constant plastic strain rate tension tests is demonstrated. The plastic strain rate and the magnitude of the initial strain are shown to have a noticeable effect on subsequent creep behavior of aluminum.

Wu, H. C.↗
NASA NTRS1981

Creep crack-growth: A new path-independent T sub o and computational studies

Two path independent integral parameters which show some degree of promise as fracture criteria are the C* and delta T sub c integrals. The mathematical aspects of these parameters are reviewed. This is accomplished by deriving generalized vector forms of the parameters using conservation laws which are valid for arbitrary, three dimensional, cracked bodies with crack surface tractions (or applied displacements), body forces, inertial effects and large deformations. Two principal conclusions are that delta T sub c is a valid crack tip parameter during nonsteady as well as steady state creep and that delta T sub c has an energy rate interpretation whereas C* does not. An efficient, small displacement, infinitestimal strain, displacement based finite element model is developed for general elastic/plastic material behavior. For the numerical studies, this model is specialized to two dimensional plane stress and plane strain and to power law creep constitutive relations.

Stonesifer, R. B.↗
NASA NTRS1982

Creep crack-growth: A new path-independent integral (T sub c), and computational studies

The development of valid creep fracture criteria is considered. Two path-independent integral parameters which show some degree of promise are the C* and (Delta T)sub c integrals. The mathematical aspects of these parameters are reviewed by deriving generalized vector forms of the parameters using conservation laws which are valid for arbitrary, three dimensional, cracked bodies with crack surface tractions (or applied displacements), body forces, inertial effects, and large deformations. Two principal conclusions are that (Delta T)sub c has an energy rate interpretation whereas C* does not. The development and application of fracture criteria often involves the solution of boundary/initial value problems associated with deformation and stresses. The finite element method is used for this purpose. An efficient, small displacement, infinitesimal strain, displacement based finite element model is specialized to two dimensional plane stress and plane strain and to power law creep constitutive relations. A mesh shifting/remeshing procedure is used for simulating crack growth. The model is implemented with the quartz-point node technique and also with specially developed, conforming, crack-tip singularity elements which provide for the r to the n-(1+n) power strain singularity associated with the HRR crack-tip field. Comparisons are made with a variety of analytical solutions and alternate numerical solutions for a number of problems.

Stonesifer, R. B.↗
NASA NTRS1981

The physics of creep and attenuation in the mantle

The objective is to investigate the role of dislocations in both creep and attenuation. Attenuation in the mantle at seismic frequencies is thought to be caused by the glide of dislocations in the subgrains. Both kink and impurity drag can contribute to the glide time constant. The kink-formation, or Peierls barrier, model for dislocation glide is seen as a low-temperature, high-frequency mechanism most appropriate for pure systems. It is noted that a small amount of impurity drag brings the dislocation glide characteristic time into the seismic band at upper-mantle temperatures. The attenuation and creep behavior of the mantle are related by way of the dislocation structure. Analysis of the various possible mechanisms is facilitated by casting them and the geophysical data in terms of a pre-exponential characteristic time and an activation energy.

Anderson, D. L.↗
NASA NTRS1982

On the solution of creep induced buckling in general structure

This paper considers the pre and post buckling behavior of general structures exposed to high temperature fields for long durations wherein creep effects become significant. The solution to this problem is made possible through the use of closed upper bounding constraint surfaces which enable the development of a new time stepping algorithm. This permits the stable and efficient solution of structural problems which exhibit indefinite tangent properties. Due to the manner of constraining/bounding successive iterates, the algorithm developed herein is largely self adaptive, inherently stable, sufficiently flexible to handle geometric material and boundary induced nonlinearity, and can be incorporated into either finite element or difference simulations. To illustrate the capability of the procedure, as well as, the physics of creep induced pre and post buckling behavior, the results of several numerical experiments are included.

Padovan, J.↗
NASA NTRS1982

Structure and creep rupture properties of directionally solidified eutectic gamma/gamma-prime-alpha alloy

A simple ternary gamma/gamma-prime-alpha alloy of nominal composition (wt-%) Ni-32Mo-6Al has been directionally solidified at 17 mm/h and tested in creep rupture at 1073, 1173, and 1273 K. A uniform microstructure consisting of square-shaped Mo fibers in a gamma + gamma-prime matrix was found despite some variation in the molybdenum and aluminum concentrations along the growth direction. Although the steady-state creep rate is well described by the normal stress temperature equation, the stress exponent (12) and the activation energy (580 kJ/mol) are high. The rupture behavior is best characterized by the Larson-Miller parameter where the constant equals 20.

Whittenberger, J. D.↗
NASA NTRS1982

Fatigue and creep-fatigue deformation of several nickel-base superalloys at 650 C

Transmission electron microscopy has been used to study the bulk deformation characteristics of seven nickel-base superalloys tested in fatigue and creep-fatigue at 650 C. The alloys were Waspalloy, HIP Astroloy, H plus F Astroloy, H plus F Rene 95, IN 100, MERL 76, and NASA IIB-7. The amount of bulk deformation observed in all the alloys was low. In tests with inelastic strain amplitudes less than about 0.003, only some grains exhibited yielding and the majority of those had the 110 line near the tensile axis. Deformation occurred on octahedral systems for all of the alloys except MERL 76 which also showed abundant primary cube slip. Creep-fatigue cycling occasionally produced extended faults between partial dislocations, but otherwise deformation was much the same as for fatigue cycling.

Miner, R. V.↗
NASA NTRS1981

Creep-rupture behavior of iron superalloys in high pressure hydrogen

Two cast alloys (CRM-6D and XF-818) and four sheet alloys (A-26, Incoloy 800H, N-155, and 19-9DL) in the thickness range of 0.79 to 0.99 mm were evaluated for use in the Stirling engine. The creep rupture behavior of these iron base high temperature alloys is being determined in air for 10 hr to 3,00 hr, and in 20.7 MPa (3,000 psi) H2 for 10 to 300 hr at temperatures of 650 deg to 925 deg. Material procurement, preparation and air creep rupture testing are described and existing data is analyzed. Systems for the high pressure hydrogen testing are discussed. Statistical analysis of temperature-compensated rupture data for each alloy is included.

Bhattacharyya, S.↗
NASA NTRS1983

Constrained Self-adaptive Solutions Procedures for Structure Subject to High Temperature Elastic-plastic Creep Effects

This paper will develop a new solution strategy which can handle elastic-plastic-creep problems in an inherently stable manner. This is achieved by introducing a new constrained time stepping algorithm which will enable the solution of creep initiated pre/postbuckling behavior where indefinite tangent stiffnesses are encountered. Due to the generality of the scheme, both monotone and cyclic loading histories can be handled. The presentation will give a thorough overview of current solution schemes and their short comings, the development of constrained time stepping algorithms as well as illustrate the results of several numerical experiments which benchmark the new procedure.

Padovan, J.↗
NASA NTRS1984

Creep-rupture reliability analysis

A probabilistic approach to the correlation and extrapolation of creep-rupture data is presented. Time temperature parameters (TTP) are used to correlate the data, and an analytical expression for the master curve is developed. The expression provides a simple model for the statistical distribution of strength and fits neatly into a probabilistic design format. The analysis focuses on the Larson-Miller and on the Manson-Haferd parameters, but it can be applied to any of the TTP's. A method is developed for evaluating material dependent constants for TTP's. It is shown that optimized constants can provide a significant improvement in the correlation of the data, thereby reducing modelling error. Attempts were made to quantify the performance of the proposed method in predicting long term behavior. Uncertainty in predicting long term behavior from short term tests was derived for several sets of data. Examples are presented which illustrate the theory and demonstrate the application of state of the art reliability methods to the design of components under creep.

Peralta-Duran, A.↗
NASA NTRS1984

A simple application of the Bailey-Orowan creep model to Fe-39.8 at. pct Al and gamma/gamma prime - alpha

The results of a study to determine the recovery rates and work-hardening coefficients for creep from constant cross-head speed compressive tests are presented. Stressing and straining rates are computed from measured time-load curves obtained from compression testing between 1200 and 1400 K of several B2 crystal structure Fe-39.8 Al intermetallic materials and the directionally solidified eutectic alloy gamma/gamma prime alpha. These quantities are then fitted to the universal form of the Bailey-Orowan equation for creep. The recovery rates were found to be functions of nominal strain rate, stress, and temperature, while the hardening coefficients were dependent only on temperature. While the work-hardening coefficient for gamma/gamma prime - alpha was about 0.05 of the elastic modulus, the work-hardening coefficients for Fe-39.8 at. pct Al were less than 0.002 of the modulus.

Whittenberger, J. D.↗
NASA NTRS1984

Vortex creep and the internal temperature of neutron stars. II - Vela pulsar

The observed complex postglitch behavior of the Vela pulsar is explained as resulting from coupling of the crust to crustal neutron superfluid, specifically that part of the superfluid in which vortex lines are pinned to crustal nuclei. It is shown how the general theory of vortex creep provides an excellent fit to the timing observations of Downs which span the decade 1969-1979 and include four giant glitches. Relaxation times, inertial moments, and limits on superfluid pinning parameters are extracted for three distinct regions of vortex pinning in the star, with results which are consistent with microscopic theories of its internal structure. Relaxation times due to vortex creep are directly proportional to the internal temperature of the star, so that the limits obtained for pinning parameters translate to bounds on this temperature. It is concluded that the internal temperature of the Vela pulsar is about 10-million K and discuss the extent to which improved calculations of vortex pinning as well as soft X-ray observations of other stars will make possible an improved determination of the pulsar temperature.

Alpar, M. A.↗
NASA NTRS1984

Algorithms for elasto-plastic-creep postbuckling

This paper considers the development of an improved constrained time stepping scheme which can efficiently and stably handle the pre-post-buckling behavior of general structure subject to high temperature environments. Due to the generality of the scheme, the combined influence of elastic-plastic behavior can be handled in addition to time dependent creep effects. This includes structural problems exhibiting indefinite tangent properties. To illustrate the capability of the procedure, several benchmark problems employing finite element analyses are presented. These demonstrate the numerical efficiency and stability of the scheme. Additionally, the potential influence of complex creep histories on the buckling characteristics is considered.

Padovan, J.↗
NASA NTRS1984

Back stress in dislocation creep. Part 1: Basic concepts and measuring techniques

A theory is proposed whereby the plastic deformation of metal materials is determined by the difference between the applied stress and the back stress which characterizes the resistance of the material to plastic deformation. The back stress is usually equivalent to the internal stress or the friction stress and depends on the magnitude of the applied stress and temperature. The concept of back stress is applied to the case of the dislocation creep of precipitation-hardened or dispersion-strengthened metal materials. An additivity rule is formulated which can be useful in interpreting the creep behavior of such materials.

Cadek, J.↗
NASA NTRS1985

Analytical simulation of weld effects in creep range

The inelastic analysis procedure used to investigate the effect of welding on the creep rupture strength of a typical Liquid Metal Fast Breeder Reactor (LMFBR) nozzle is discussed. The current study is part of an overall experimental and analytical investigation to verify the inelastic analysis procedure now being used to design LMFBR structural components operating at elevated temperatures. Two important weld effects included in the numerical analysis are: (1) the residual stress introduced in the fabrication process; and (2) the time-independent and the time-dependent material property variations. Finite element inelastic analysis was performed on a CRAY-1S computer using the ABAQUS program with the constitutive equations developed for the design of LMFBR structural components. The predicted peak weld residual stresses relax by as much as 40% during elevated temperature operation, and their effect on creep-rupture cracking of the nozzle is considered of secondary importance.

Dhalla, A. K.↗