Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONTROL SYSTEMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1944

A Theoretical Investigation of Longitudinal Stability of Airplanes with Free Controls Including Effect of Friction in Control System

The relation between the elevator hinge moment parameters and the control forces for changes in forward speed and in maneuvers is shown for several values of static stability and elevator mass balance. The stability of the short period oscillations is shown as a series of boundaries giving the limits of the stable regions in terms of the elevator hinge moment parameters. The effects of static stability, elevator moment of inertia, elevator mass unbalance, and airplane density are also considered. Dynamic instability is likely to occur if there is mass unbalance of the elevator control system combined with a small restoring tendency (high aerodynamic balance). This instability can be prevented by a rearrangement of the unbalancing weights which, however, involves an increase of the amount of weight necessary. It can also be prevented by the addition of viscous friction to the elevator control system provided the airplane center of gravity is not behind a certain critical position. For high values of the density parameter, which correspond to high altitudes of flight, the addition of moderate amounts of viscous friction may be destabilizing even when the airplane is statically stable. In this case, increasing the viscous friction makes the oscillation stable again. The condition in which viscous friction causes dynamic instability of a statically stable airplane is limited to a definite range of hinge moment parameters. It is shown that, when viscous friction causes increasing oscillations, solid friction will produce steady oscillations having an amplitude proportional to the amount of friction.

Greenberg, Harry↗
NASA NTRS1984

Digital control system for space structural dampers

Digital control systems for space structural dampers, also referred to as inertia or proof-mass dampers are investigated. A damper concept is improved by adding a small taper to the proof-mass, and using a proximeter to determine position. Another damper using a three inch stroke rather than the standard one inch stroke is described. Provisions are made for a relative velocity feedback. In one approach, the digital controller is modified to accept the signal from a linear velocity transducer. In the other, the velocity feedback is included in the digital program. An overall system concept for the use of the dampers is presented.

Haviland, J. K.↗
NASA NTRS1985

The interpretation of flying qualities requirements for flight control system design

An experimental flight test program was designed for the Total In Flight Simulator (TIFS) directed toward the interface between flying qualities requirements and flight control system design criteria. The eventual goal is to provide an interpretation or translation of flying qualities requirements for use by the flight control system designer. Specifically, an angle of attack and pitch rate command system matrix involving both short term and long term dynamics are specified for evaluation. Flying qualities criteria and flight control system configuration or architecture can be independent was demonstrated. Finally, additional configurations are proposed to evaluate the efficacy of dynamic decoupling.

Rynaski, E. G.↗
NASA NTRS2021

A Learn-to-Fly Approach for Adaptively Tuning Flight Control Systems

A method is presented for adaptively tuning feedback control gains in a flight control system to achieve desired closed-loop performance. The method combines efficient aircraft parameter estimation, for identifying closed-loop dynamics models, with online nonlinear optimization, for sequentially perturbing and updating control gains to improve performance. Access to flight measurements and the control gains is required, but no prior information about the aircraft dynamics or the flight control architecture is needed. After the procedure, the optimized control gains (with uncertainties), the open-loop dynamics model, and the closed-loop dynamics model are available. The method is demonstrated for tuning a longitudinal stability augmentation system using a realistic nonlinear flight dynamics simulation of a subscale airplane. Convergence was attained using five maneuvers that spanned approximately one minute of flight test time. Although shown for a relatively simple case, the method is general and can be applied to other aircraft, axes of motion, performance metrics, and control system designs.

Adaptive tuning↗
NASA NTRS1992

NASA TSRV essential flight control system requirements via object oriented analysis

The objective was to analyze the baseline flight control system of the Transport Systems Research Vehicle (TSRV) and to develop a system specification that offers high visibility of the essential system requirements in order to facilitate the future development of alternate, more advanced software architectures. The flight control system is defined to be the baseline software for the TSRV research flight deck, including all navigation, guidance, and control functions, and primary pilot displays. The Object Oriented Analysis (OOA) methodology developed is used to develop a system requirement definition. The scope of the requirements definition contained herein is limited to a portion of the Flight Management/Flight Control computer functionality. The development of a partial system requirements definition is documented, and includes a discussion of the tasks required to increase the scope of the requirements definition and recommendations for follow-on research.

Duffy, Keith S.↗
NASA NTRS1977

Information distribution in distributed microprocessor based flight control systems

This paper presents an optimal control theory that accounts for variable time intervals in the information distribution to control effectors in a distributed microprocessor based flight control system. The theory is developed using a linear process model for the aircraft dynamics and the information distribution process is modeled as a variable time increment process where, at the time that information is supplied to the control effectors, the control effectors know the time of the next information update only in a stochastic sense. An optimal control problem is formulated and solved that provides the control law that minimizes the expected value of a quadratic cost function. An example is presented where the theory is applied to the control of the longitudinal motions of the F8-DFBW aircraft. Theoretical and simulation results indicate that, for the example problem, the optimal cost obtained using a variable time increment Markov information update process where the control effectors know only the past information update intervals and the Markov transition mechanism is almost identical to that obtained using a known uniform information update interval.

Montgomery, R. C.↗
NASA NTRS1982

Space Telescope Pointing Control System software

The Space Telescope Pointing Control System software is in the advanced development stage, having been tested on both the airbearing and the static simulator. The overall structure of the software is discussed, along with timing and sizing evaluations. The interaction between the controls analysts and software designer is described.

Dougherty, H.↗
NASA NTRS1982

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗
NASA NTRS1991

Modeling and simulations of the DSS 13 antenna control system

A model of the antenna control system for the azimuth and elevation axes of the Deep Space Station (DSS) 13 antenna is developed. This model is used for simulation of elevation and azimuth dynamics, cross-coupled dynamics, and radio-frequency pointing error due to both input commands and wind disturbances. This model also serves as a tool for the antenna controller design. A modal state-space model of the antenna structure was obtained from its finite-element model with a free-rotating tipping structure and alidade. Model reduction techniques applied separately for the antenna structure, elevation, and azimuth drives, and rate-loop model reduce the system order to one-third of that of the original, while preserving its significant dynamic properties. Extensive simulation results illustrate properties of the model.

Gawronski, W.↗
NASA NTRS1991

Wheel speed management control system for spacecraft

A spacecraft attitude control system uses at least four reaction wheels. In order to minimize reaction wheel speed and therefore power, a wheel speed management system is provided. The management system monitors the wheel speeds and generates a wheel speed error vector. The error vector is integrated, and the error vector and its integral are combined to form a correction vector. The correction vector is summed with the attitude control torque command signals for driving the reaction wheels.

Goodzeit, Neil E.↗
NASA NTRS1993

Upgrading NASA/DOSE laser ranging system control computers

Laser ranging systems now managed by the NASA Dynamics of the Solid Earth (DOSE) and operated by the Bendix Field Engineering Corporation, the University of Hawaii, and the University of Texas have produced a wealth on interdisciplinary scientific data over the last three decades. Despite upgrades to the most of the ranging station subsystems, the control computers remain a mix of 1970's vintage minicomputers. These encompass a wide range of vendors, operating systems, and languages, making hardware and software support increasingly difficult. Current technology allows replacement of controller computers at a relatively low cost while maintaining excellent processing power and a friendly operating environment. The new controller systems are now being designed using IBM-PC-compatible 80486-based microcomputers, a real-time Unix operating system (LynxOS), and X-windows/Motif IB, and serial interfaces have been chosen. This design supports minimizing short and long term costs by relying on proven standards for both hardware and software components. Currently, the project is in the design and prototyping stage with the first systems targeted for production in mid-1993.

Ricklefs, Randall L.↗
NASA NTRS2003

Human Factors Considerations for Safe Recovery from Faults In Flight Control Systems

It is now possible - and important - to develop systems to help resolve Flight Control System (FCS) faults. From a human factors viewpoint, it is imperative that these systems take on roles, and provide functions, that are the most supportive to the pilot, given the stress, time pressure and workload they may experience following a FCS fault. FCS fault recovery systems may provide several different functions, including alerting, control assistance, and decision aiding. The biggest human factors questions are in the role suitable for the technology, and its specific functioning to achieve that role. Specifically, for these systems to be effective, they must meet the fundamental requirements that (1) they alert pilots to problems early enough that the pilot can reasonably resolve the fault and regain control of the aircraft and that (2) if the aircraft s handling qualities are severely degraded the HMS provide the appropriate stability augmentation to help the pilot stabilize and control the aircraft. This project undertook several research steps to develop such systems, focusing on the capabilities of pilots and on realistically attainable technologies. The ability to estimate which functions are the most valuable will help steer system development in the directions that can establish the highest safety levels.

Pritchett, Amy↗
NASA NTRS1979

Handbook on astronaut crew motion disturbances for control system design

The analyses and results pertinent to the characterization of the disturbances imparted to the Skylab vehicle by the T-013 crew motion experiments are summarized. Guidelines to help control system designers assess anticipated crew motion disturbances during the design cycle of a new manned spacecraft control system are provided. These guidelines, in conjunction with the T-013 characterizations outlined, begin with the control system conceptual design and conclude with preliminary expectations for pointing performance as affected by crew motions. Block diagrams to highlight the contents so that the reader can easily identify the information and data flow are used. These diagrams provide a handy cross reference of related topics.

Kullas, M. C.↗
NASA NTRS1958

Investigation of a Nonlinear Control System

A discontinuous variation of coefficients of the differential equation describing the linear control system before nonlinear elements are added is studied in detail. The nonlinear feedback is applied to a second-order system. Simulation techniques are used to study performance of the nonlinear control system and to compare it with the linear system for a wide variety of inputs. A detailed quantitative study of the influence of relay delays and of a transport delay is presented.

Flugge-Lotz, I↗
NASA NTRS1987

Spectrum-modulating fiber-optic sensors for aircraft control systems

A family of fiber-optic sensors for aircraft engine control systems is described. Each of these sensors uses a spectrum-modulation method to obtain an output which is largely independent of the fiber link transmissivity. A position encoder is described which uses a code plate to digitally modulate the sensor output spectrum. Also described are pressure and temperature sensors, each of which uses a Fabry-Perot cavity to modulate the sensor output spectrum as a continuous function of the measurand. A technique is described whereby a collection of these sensors may be effectively combined to perform a number of the measurements which are required by an aircraft-engine control system.

Beheim, Glenn↗
NASA NTRS2004

ADAPTIVE CLEARANCE CONTROL SYSTEMS FOR TURBINE ENGINES

The Controls and Dynamics Technology Branch at NASA Glenn Research Center primarily deals in developing controls, dynamic models, and health management technologies for air and space propulsion systems. During the summer of 2004 I was granted the privilege of working alongside professionals who were developing an active clearance control system for commercial jet engines. Clearance, the gap between the turbine blade tip and the encompassing shroud, increases as a result of wear mechanisms and rubbing of the turbine blades on shroud. Increases in clearance cause larger specific fuel consumption (SFC) and loss of efficient air flow. This occurs because, as clearances increase, the engine must run hotter and bum more fuel to achieve the same thrust. In order to maintain efficiency, reduce fuel bum, and reduce exhaust gas temperature (EGT), the clearance must be accurately controlled to gap sizes no greater than a few hundredths of an inch. To address this problem, NASA Glenn researchers have developed a basic control system with actuators and sensors on each section of the shroud. Instead of having a large uniform metal casing, there would be sections of the shroud with individual sensors attached internally that would move slightly to reform and maintain clearance. The proposed method would ultimately save the airline industry millions of dollars.

Blackwell, Keith M.↗