SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Device installed on commercial 747 airliners and operated during normal passenger service combines sensitive air constituent measuring instruments with modern aircraft avionics and data acquisition equipment to automatically monitor air quality on worldwide basis. System may be modified for use in remote unmanned ground monitoring stations.
The activities conducted as a planning effort to focus attention on the applicability of the global positioning system for general aviation are described. The description of GPS, its impact on economic and functional aspects of general aviation avionics, as well as a declaration of potential extensions of the basic concept have been studied in detail.
The mathematical model implementation of the elevon subsystem for the shuttle actuators simulator in the Shuttle Avionics Integration Laboratory is described. The computer subsystem simulated two outboard and two inboard elevon actuators.
The generalized environmental control and life support system (ECLSS) computer program (G189A) simulation of the shuttle orbiter ECLSS was upgraded. The G189A component model configuration was changed to represent the current PV102 and subsequent vehicle ECLSS configurations as defined by baseline ARS and ATCS schematics. The diagrammatic output schematics of the gas, water, and freon loops were also revised to agree with the new ECLSS configuration. The accuracy of the transient analysis was enhanced by incorporating the thermal mass effects of the equipment, structure, and fluid in the ARS gas and water loops and in the ATCS freon loops. The sources of the data used to upgrade the simulation are: (1) ATCS freon loop line sizes and lengths; (2) ARS water loop line sizes and lengths; (3) ARS water loop and ATCS freon loop component and equipment weights; and (4) ARS cabin and avionics bay thermal capacitance and conductance values. A single G189A combination master program library tape was generated which contains all of the master program library versions which were previously maintained on separate tapes. A new component subroutine, PIPETL, was developed and incorporated into the G189A master program library.
The STOLAND system includes air data, navigation, guidance, flight director (including a throttle flight director on the Augmentor Wing), 3-axis autopilot and autothrottle functions. The 3-axis autopilot and autothrottle control through parallel electric servos on both aircraft and on the augmentor wing, the system also interfaces with three electrohydraulic series actuators which drive the roll control surfaces, elevator and rudder. The system incorporates automatic configuration control of the flaps and nozzles on the augmentor wing and of the flaps on the Twin Otter. Interfaces are also provided to control the wing flap chokes on the Augmentor Wing and the spoilers on the Twin Otter. The STOLAND system has all the capabilities of a conventional integrated avionics system. Aircraft stabilization is provided in pitch, roll and yaw including control wheel steering in pitch and roll. The basic modes include altitude hold and select, indicated airspeed hold and select, flight path angle hold and select, and heading hold and select. The system can couple to TACAN and VOR/DME navaids for conventional radial flying.
Methods for accommodating payloads in SAIL are evaluated. It is concluded that a special payload be used as the standard method for verifying avionics systems and experiments. It is recommended that the baselined North door entrance method be retained for accommodation of flight type payloads.
A digital avionics system referred to as STOLAND was test flown in the NASA CV-340 aircraft to obtain performance data for time controlled guidance in the manual flight director mode. The advanced system components installed in the cockpit included an electronic attitude director indicator and an electronic multifunction display. Navigation guidance and control computations were performed on a digital computer. A detailed 4D area navigation systems description is given. The pilot/system interface and systems operation and performance are also described. Approach flightpaths were flown which included a 180 deg turn and a 1-min, 5 deg straight-in approach to 30 m altitude, at which point go-around was initiated. Results are presented for 19 approaches.
Highly reliable fault-tolerant computer systems are discussed for use in flight-critical avionic and control systems of future commercial transport aircraft. Such aircraft are envisioned to have integrated systems, to be terminally configured, and to be equipped with fly-by-wire flight control systems, all of which require highly reliable, fault-tolerant computers. Two candidate computer architectures are identified as having the potential of satisfying the commercial transport aircraft requirements.
The LORAN program is stored in CMS disk files for use by Avionics Engineering Center terminal users. A CMS EXEC file named LORAN controls program operation. The user types LORAN and the program then prompts for data input and produces output on the terminal. The FORTRAN program refers to a disk file of LORAN master data giving station locations, coding delays, repetition rate and station pair identification letters. For Geographic-to-LORAN conversion, no iterative computations are required; the program is a straightforward coordinate conversion based upon the techniques described by the Navy. For LORAN-to-Geographic conversion, the original Navy program required a dead-reckoned position, near the actual unknown fix, to begin computations. No iteration was performed to obtain the LORAN fix, but internal program errors occurred at execution time if the dead-reckoned fix were displaced from the actual fix by more than a few minutes of latitude or longitude. In order to enhance usefulness of the program for the terminal user, an iterative routine was added which allows a single dead-reckoned position to be entered from the master data file for each LORAN chain. The results compare exactly with the LORAN-C navigation chart, and provide adequate benchmark data for general aviation flight planning and data analysis.
The utilization is discussed of the GPSPAC, which is presently being developed to be used on the low altitude host vehicle (LAHV), for possible use in the shuttle avionics system to evaluate shuttle/GPS navigation performance. Analysis and tradeoffs of the shuttle/GPS link, shuttle signal interface requirements, oscillator tradeoffs and GPSPAC mechanical modifications for shuttle are included. Only the on-orbit utilization of GPSPAC for the shuttle is discussed. Other phases are briefly touched upon. Recommendations are provided for using the present GPSPAC and the changes required to perform shuttle on-orbit navigation.
A model of a UH-1H helicopter was developed to support flight simulations and for developmental work on an avionics system known as V/STOLAND system. Equations and numerical values of constants used to represent the helicopter are presented. Responses to stop inputs of the cyclic and collective controls are shown and compared with flight test data for a UH-1H. The model coefficients were adjusted in an attempt to get a consistant match with the flight time histories at hover and 60 knots. Response matching was obtained at 60 knots, but the matching at hover was not as successful. Pilot evaluations of the model, both fixed and moving base, were made.
The Orbiter Avionics and the Spacelab Command and Data Management System (CDMS) combine to provide a relatively complete command, control, and data handling service to the instrument complement during a Shuttle Sortie Mission. The Spacelab CDMS services the instruments and the Orbiter in turn services the Spacelab. The CDMS computer system includes three computers, two I/O units, a mass memory, and a variable number of remote acquisition units. Attention is given to the CDMS high rate multiplexer, CDMS tape recorders, closed circuit television for the visual monitoring of payload bay and cabin area activities, methods of science data acquisition, questions of transmission and recording, CDMS experiment computer usage, and experiment electronics.
Improvements in performance, safety, efficiency, and emissions control in general aviation craft are reviewed. While change is slow, the U.S. industries still account for the bulk (90%) of the world's general aviation fleet. Advances in general aviation aerodynamics, structures and materials, acoustics, avionics, and propulsion are described. Supercritical airfoils, drag reduction design, stall/spin studies, crashworthiness and passenger safety, fiberglass materials, flight noise abatement, interior noise and vibration reduction, navigation systems, quieter and cleaner (reciprocating, turboprop, turbofan) engines, and possible benefits of the Global Position Satellite System to general aviation navigation are covered in the discussion. Some of the developments are illustrated.
The paper considers STS payload-interface verification requirements and the capability provided by STS to support verification. The intent is to standardize as many interfaces as possible, not only through the design, development, test and evaluation (DDT and E) phase of the major payload carriers but also into the operational phase. The verification process is discussed in terms of its various elements, such as the Space Shuttle DDT and E (including the orbital flight test program) and the major payload carriers DDT and E (including the first flights). Five tools derived from the Space Shuttle DDT and E are available to support the verification process: mathematical (structural and thermal) models, the Shuttle Avionics Integration Laboratory, the Shuttle Manipulator Development Facility, and interface-verification equipment (cargo-integration test equipment).
Iterative procedures were used to analyze the performance of two preliminary shuttle/GPS navigation system configurations: an early OFT experimental system and a more sophisticated system which consolidates several separate navigation functions thus permitting net cost savings from decreased shuttle avionics weight and power consumption, and from reduced ground data processing. The GPS system can provide on-orbit navigation accuracy an order of magnitude better than the baseline system, with very adequate link margins. The worst-case link margin is 4.3 dB. This link margin accounts for shuttle RF circuit losses which were minimized under the constraints of program schedule and environmental limitations. Implicit in the link analyses are the location trade-offs for preamplifiers and antennas.
A brief summary of the work performed on the Approach and Landing Test (ALT) shuttle flight control system is presented. (FCS) and a bibliography of the formal reports are included which document the activities in detail. In general, the activities were grouped in four categories: (1) independent evaluation of ALT FCS software design; (2) independent evaluation of Software Development Laboratory (SDL) testing of ALT FCS software; (3) independent evaluation of Shuttle Avionics Integration Laboratory (SAIL) ALT FCS testing; and (4) independent evaluation of ALT flight test results.
Labor and materials costs associated with maintaining and operating 12 commuter airlines carrying an average of from 42 to 1,100 passengers daily in a variety of aircraft types were studied to determine the total direct maintenance cost per flight hour for the airframe, engine, and avionics and other instruments. The distribution of maintenance costs are analyzed for two carriers, one using turboprop aircraft and the other using piston engine aircraft.
The requirements and specifications for a general purpose payload communications system simulator to be used to emulate those communications system portions of NASA and DOD payloads/spacecraft that will in the future be carried into earth orbit by the shuttle are discussed. For the purpose of on-orbit checkout, the shuttle is required to communicate with the payloads while they are physically located within the shuttle bay (attached) and within a range of 20 miles from the shuttle after they have been deployed (detached). Many of the payloads are also under development (and many have yet to be defined), actual payload communication hardware will not be available within the time frame during which the avionic hardware tests will be conducted. Thus, a flexible payload communication system simulator is required.