Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “zinc oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

12.3% Efficient Lifted-Off and Reconstructed As-Doped CdTe Thin Film Solar Cell

CdTe:As devices grown by MOCVD in the superstrate configuration have been reconfigured to a substrate structure, by employing a cleaving and reconstruction technique. Indium and aluminium doped Zinc oxide (IZO and AZO) layers were used as the transparent front interface without a metal grid. A substrate efficiency of 12.3% was realized with AZO front contact, retaining 80% of the superstrate device efficiency and an impressive approximately 99% of the open-circuit voltage. The IZO-based substrate device on the other hand performed at approximately 69 % retained efficiency. The crucial role of front interfaces is highlighted by the two contacts used here. The results in this work show promise for the development of highly efficient substrate CdTe:As devices.

II-VI semiconductor materials↗
DOE OSTI2020

Combinatorial Study of MZO Emitters for CdTe-Based Solar Cells

Precise band alignment at the front interface of CdTe-based solar cells is necessary to reduce photoexcited charge carrier recombination and to enable higher energy conversion efficiencies. Magnesium zinc oxide is not only transparent but also offers the ability to tune the conduction band offset with CdTe at the front of the device stack. In this work, we describe reactive sputtering of Mg 1-x Zn x O using metal targets and its application in CdTe photovoltaics. Combinatorial libraries of Mg 1-x Zn x O were created to tune the conduction band alignment for the optimal performance of CdTe solar cells. Band gap variation of more than 0.4 eV is achieved across a 3-inch substrate. Kelvin probe measurements demonstrate variance of work function across the substrate. Device performance is optimized at band gaps of 3.5 eV for the CdTe device processing conditions employed in this study.

14 SOLAR ENERGY↗
DOE OSTI2022

Nanostructured ZnO-Based Electrochemical Sensor with Anionic Surfactant for the Electroanalysis of Trimethoprim

In this research, detection of trimethoprim (TMP) was carried out using a nanostructured zinc oxide nanoparticle-modified carbon paste electrode (ZnO/CPE) with an anionic surfactant and sodium dodecyl sulphate (SDS) with the help of voltametric techniques. The electrochemical nature of TMP was studied in 0.2 M pH 3.0 phosphate-buffer solution (PBS). The developed electrode displayed the highest peak current compared to nascent CPE. Effects of variation in different parameters, such as pH, immersion time, scan rate, and concentration, were investigated. The electrode process of TMP was irreversible and diffusion controlled with two electrons transferred. The effective concentration range (8.0 × 10 -7 M–1.0 × 10 -5 M) of TMP was obtained by varying the concentration with a lower limit of detection obtained to be 2.58 × 10 -8 M. In addition, this approach was effectively employed in the detection of TMP in pharmaceutical dosages and samples of urine with the excellent recovery data, suggesting the potency of the developed electrode in clinical and pharmaceutical sample analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strong Potential Gradients and Electron Confinement in ZnO Nanoparticle Films: Implications for Charge-Carrier Transport and Photocatalysis

We report that zinc oxide (ZnO) nanomaterials are promising components for chemical and biological sensors and photocatalytic conversion and operate as electron collectors in photovoltaic technologies. Many of these applications involve nanostructures in contact with liquids or exposed to ambient atmosphere. Under these conditions, single-crystal ZnO surfaces are known to form narrow electron accumulation layers with few nanometer spatial penetration into the bulk. A key question is to what extent such pronounced surface potential gradients can develop in the nanophases of ZnO, where they would dominate the catalytic activity by modulating charge-carrier mobility and lifetimes. Here, we follow the temperature-dependent surface electronic structure of nanoporous ZnO with photoemission spectroscopy to reveal a sizable, spatially averaged downward band bending for the hydroxylated state and a conservative upper bound of < 6 nm for the spatial extent of the associated potential gradient. This nanoscale confinement of conduction-band electrons to the nanoparticle film surface is crucial for a microscopic understanding and further optimization of charge transport and photocatalytic function in complex ZnO nanomaterials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Swelling-Assisted Sequential Infiltration Synthesis of Nanoporous ZnO Films with Highly Accessible Pores and Their Sensing Potential for Ethanol

Here, we report a swelling-assisted sequential infiltration synthesis (SIS) approach for the design of highly porous zinc oxide (ZnO) films by infiltration of block copolymer templates such as polystyrene-block- polyvinyl pyridine with inorganic precursors followed by UV ozone-assisted removal of the polymer template. We show that porous ZnO coatings with the thickness in the range between 140 and 420 nm can be obtained using only five cycles of SIS. The pores in ZnO fabricated via swelling-assisted SIS are highly accessible, and up to 98% of pores are available for solvent penetration. The XPS data indicate that the surface of nanoporous ZnO films is terminated with -OH groups. Density functional theory calculations show a lower energy barrier for ethanol-induced release of the oxygen restricted depletion layer in the case of the presence of -OH groups at the ZnO surface, and hence, it can lead to higher sensitivity in sensing of ethanol. We monitored the response of ZnO porous coatings with different thicknesses and porosities to ethanol vapors using combined mass-based and chemiresistive approaches at room temperature and 90 °C. The porous ZnO conformal coatings reveal a promising sensitivity toward detection of ethanol at low temperatures. In conclusion our results suggest the excellent potential of the SIS approach for the design of conformal ZnO coatings with controlled porosity, thickness, and composition that can be adapted for sensing applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Polymer infiltration synthesis of inorganic nanoporous coatings: Does polymer template affect their properties?

Synthesis of all-inorganic metal oxide architectures using polymer templates offers control over their thickness, porosity, and composition. Here, in this study, we provide insights into the synthesis of nanoporous zinc oxide films as a model system via infiltration of polymers that have different mechanisms of interaction with metal oxide precursors such as a polymer of intrinsic microporosity (PIM-1) and representative of the block-copolymers family (polystyrene-polyvinyl pyridine block copolymer). We investigated polymer infiltration process with both gas (diethyl zinc, DEZ, and water vapors) and solution (zinc acetylacetonate, Zn(acac) 2 , dissolved in ethanol) phase precursors. Using quartz crystal microbalance (QCM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses, we systematically studied the effect of polymer template and the form of the metal oxide precursors on the properties of synthesized metal oxide thin coatings. We demonstrate that the infiltration of polymer templates can be efficiently achieved using both gas phase and solution phase precursors. We show that the crystallinity of the synthesized 200 nm ZnO films is mainly affected by the state of the precursor (gas or solution phase) and does not depend on the polymer template type. In turn, the polymer type affects the surface termination of ZnO films. We demonstrate that the surface of porous ZnO coatings synthesized with BCP (here PS-P4VP) is more accessible than the surface of ZnO synthesized with PIM; however, despite the lower surface accessibility for ethanol molecules, ZnO synthesized via infiltration of PIM-1 with solution-phase precursors demonstrates the largest change in resistivity upon its exposure to ethanol vapor at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sequential Infiltration Synthesis (SIS) of In 2 O 3 -Based Porous Photoelectrodes for Molecular Sensitization

High-surface-area photoelectrodes are highly desirable for solar energy conversion applications, particularly in systems where surface-bound molecular chromophores are responsible for light absorption. To this end, porous Indium-Zinc-Oxide (IZO) frameworks are fabricated via Sequential Infiltration Synthesis (SIS) into poly(methyl methacrylate) (PMMA) films followed by air annealing. A more complete understanding of the multimetal infiltration process conditions and postannealing temperature allows for precise control of zinc (Zn) incorporation to afford porous, conductive, transparent, and amorphous photoelectrodes. Uniform incorporation of both indium (In) and Zn is found to require extended diethylzinc (DEZ) exposures to compensate for remarkably slow precursor diffusion in the presence of indium oxyhydroxide nuclei. SIS-fabricated IZO photoelectrodes are structurally robust, electrochemically active, and exhibit dye adsorption that suggest practical surface area enhancements greater than 100×. In conclusion, these attributes establish SIS as a rapid, scalable, and reproducible route to photoelectrodes for solar energy conversion and hybrid interface characterization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Techno-economic analysis of the use of atomic layer deposited transition metal oxides in silicon heterojunction solar cells

The industry for producing silicon solar cells and modules has grown remarkably over the past decades, with more than a 100-fold reduction in price over the past 45?years. The main solar cell fabrication technology has shifted over that time and is currently dominated by the passivated emitter and rear cell (PERC). Other technologies are expected to increase in market share, including tunnel-oxide passivated contact (TOPCon) and heterojunction technology (HJT). In this paper, we examine the cost potential for using atomic layer deposition (ALD) to form transition metal oxide (TMO) layers (MoO x , TiO x and aluminium-doped zinc oxide [AZO]) to use as lower cost alternatives of the p-doped, n-doped and indium tin oxide (ITO) layers, respectively, the layers normally used in HJT solar cells. Using a bottom-up cost and uncertainty model with equipment cost data and process experience in the lab, we find that the production cost of these variations will likely be lower per wafer than standard HJT, with the main cost drivers being the cost of the ALD precursors at high-volume production. We then considered what efficiency is required for these sequences to be cost effective in $/W and discuss whether these targets are technically feasible. This work motivates further work in developing these ALD TMO processes to increase their efficiency towards their theoretical limits to take advantage of the processing cost advantage.

14 SOLAR ENERGY↗
DOE OSTI2020

Ptychographic atomic electron tomography: Towards three-dimensional imaging of individual light atoms in materials

Through numerical simulations, we demonstrate the combination of ptychography and atomic electron tomography as an effective method for low dose imaging of individual low-Z atoms in three dimensions. After generating noisy diffraction patterns with multislice simulations of an aberration-corrected scanning transmission electron microscope through a 5-nm zinc-oxide nanoparticle, we have achieved three-dimensional (3D) imaging of individual zinc and oxygen atoms and their defects by performing tomography on ptychographic projections. The methodology has also been simulated in 2D materials, resolving individual sulfur atoms in vertical WS 2 /WSe 2 van der Waals heterostructure with a low total electron dose where annular-dark-field images fail to resolve. Overall, we envision that the development of this method could be instrumental in studying the precise 3D atomic structures of radiation sensitive systems and low-Z atomic structures such as 2D heterostructures, catalysts, functional oxides, and glasses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Material Failure Mechanisms of Alkaline Zn Rechargeable Conversion Electrodes

Zinc (Zn) alkaline electrodes hold great importance and promise in the battery technology community, yet their behavior in real-world applications is still poorly understood. Here, we report a study of failure mechanisms and material evolution during cycling of 27 zinc–manganese dioxide (Zn–MnO 2 ) cells wherein the percent utilization of the Zn electroactive material is systematically varied between 1 and 16%. Cell fabrication is kept typical of the prevailing industrial cell design. The cycle life ranges from 2800 to 60, depending inversely on the Zn utilization. In all cases, the Zn material microstructure sheds the polytetrafluoroethylene (PTFE) binder and forms zinc oxide (ZnO) rods, with longer rods formed by lower current per Zn mass. Irreversible side reactions such as the hydrogen evolution reaction (HER), short circuits, or gas crossover cause the Zn anode’s charging efficiency to average 92% (as low as 86%), which in turn causes the baseload of metallic Zn to gradually disappear. Cell failure occurs after the baseload of metallic Zn is exhausted. The total lifetime discharge capacity remains constant near 12 ± 5 Ah/g Zn invariant of Zn utilization, which suggests that the aforementioned processes of Zn microstructural evolution and side-reaction destruction of baseload metallic zinc both progress linearly with cell capacity throughput. Manual reproduction of individual Zn failure mechanisms is performed in 22 fresh cells. Tight packing of the microstructure can lead to poor mass transfer, which causes supersaturation of soluble Zn and finally produces a high overvoltage during discharge. Here, the low charging current density yields poor coulombic efficiency due either to the competitive HER or soft short circuits.

25 ENERGY STORAGE↗
DOE OSTI2021

Tunable room-temperature ferromagnetism in Co-doped two-dimensional van der Waals ZnO

The recent discovery of ferromagnetism in two-dimensional van der Waals crystals has provoked a surge of interest in the exploration of fundamental spin interaction in reduced dimensions. However, existing material candidates have several limitations, notably lacking intrinsic room-temperature ferromagnetic order and air stability. Here, motivated by the anomalously high Curie temperature observed in bulk diluted magnetic oxides, we demonstrate room-temperature ferromagnetism in Co-doped graphene-like Zinc Oxide, a chemically stable layered material in air, down to single atom thickness. Through the magneto-optic Kerr effect, superconducting quantum interference device and X-ray magnetic circular dichroism measurements, we observe clear evidences of spontaneous magnetization in such exotic material systems at room temperature and above. Transmission electron microscopy and atomic force microscopy results explicitly exclude the existence of metallic Co or cobalt oxides clusters. X-ray characterizations reveal that the substitutional Co atoms form Co 2+ states in the graphitic lattice of ZnO. By varying the Co doping level, we observe transitions between paramagnetic, ferromagnetic and less ordered phases due to the interplay between impurity-band-exchange and super-exchange interactions. Our discovery opens another path to 2D ferromagnetism at room temperature with the advantage of exceptional tunability and robustness.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Direct Synthesis of Highly Siliceous ZnO-FAU Zeolite with Enhanced Performance in Hydrocarbon Cracking Reactions

The hydrothermal stability and catalytic activity of zeolite Y (faujasite, FAU) is highly dependent on its composition. High silicon content is often desirable for catalytic applications; however, direct synthesis of faujasite with high silicon content (Si/Al > 2.5) is nontrivial. Here, we present an organic-free synthesis of FAU-type zeolite with Si/Al = 3.4 using zinc oxide as a modifier. A combination of spectroscopy and microscopy confirm that ZnO is well-distributed within zeolite pores as extra-framework species, and the nature of these species differs from bulk ZnO and framework zinc in Zn-FAU crystals. We demonstrate that the increased Si/Al ratio leads to improved hydrothermal stability, while catalytic cracking of 1-hexene and cumene show that ZnO-FAU exhibits significantly longer lifetime compared to in-house and commercial zeolite Y. Collectively, this study presents a facile and efficient method to prepare more siliceous FAU with enhanced catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Depth-resolved thermal conductivity and damage in swift heavy ion irradiated metal oxides

We investigated thermal transport in swift heavy ion (SHI) irradiated insulating single crystalline oxide materials: yttrium aluminum garnet- Y 3 Al 5 O 12 (YAG), sapphire (Al 2 O 3 ), zinc oxide (ZnO) and magnesium oxide (MgO) irradiated by 167 MeV Xe ions at 10 12 – 10 14 ions/cm 2 fluences. Depth profiling of the thermal transport on nano- and micro- meter scales was assessed by time-domain thermoreflectance (TDTR) and modulated thermoreflectance (MTR) methods, respectively. This combination allowed us to isolate the conductivities of different sub-surface damage-regions characterized by their distinct microstructure evolution regimes. Thermal conductivity degradation in SHI irradiated YAG and Al 2 O 3 is attributed to formation of ion tracks and subsequent amorphization, while in ZnO and MgO it is mostly due to point defects. Additionally, notably lower conductivity when probed by very low penetrating thermal waves is consistent with surface hillock formation. An analytical model based on Klemens-Callaway method for thermal conductivity coupled with a simplified microstructure evolution capturing saturation in defect concentration was used to obtain depth dependent damage across the ion impacted region. The studies showed that YAG has the highest damage profile resulting in the less dependence of thermal conductivity with the depth, while MgO on the contrary has the strongest dependence. The presented work sheds new light on how SHI induced defects affect thermal transport degradation and recovery of oxide ceramics as promising candidates for next generation nuclear reactor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Degradation Mechanism Due to Water Ingress Effect on the Top Contact of Cu(In,Ga)Se2 Solar Cells

The impact of moisture ingress on the surface of copper indium gallium diselenide (CIGS) solar cells was studied. While industry-scale modules are encapsulated in specialized polymers and glass, over time, the glass can break and the encapsulant can degrade. During such conditions, water can potentially degrade the interior layers and decrease performance. The first layer the water will come in contact with is the transparent conductive oxide (TCO) layer. To simulate the impact of this moisture ingress, complete devices were immersed in deionized water. To identify the potential sources of degradation, a common window layer for CIGS devices—a bilayer of intrinsic zinc oxide (i-ZnO) and conductive indium tin oxide (ITO)—was deposited. The thin films were then analyzed both pre and post water soaking. To determine the extent of ingress, dynamic secondary ion mass spectroscopy (SIMS) was performed on completed devices to analyze impurity diffusion (predominantly sodium and potassium) in the devices. The results were compared to device measurements, and indicated a degradation of device efficiency (mostly fill factor, contrary to previous studies), potentially due to a modification of the alkali profile.

14 SOLAR ENERGY↗
DOE OSTI2026

Molecularly engineered ZnO–carbon nanosheets from fumaric acid precursors for efficient photocatalytic water purification

The photocatalytic breakdown of organic contaminants is crucial for the development of water purification technology. Zinc oxide (ZnO) is an extensively researched photocatalyst; however, its efficacy is hindered by rapid charge recombination and limited utilization of UV irradiation. Resolving these issues necessitates integrating ZnO with conductive carbon phases via scalable, low-temperature synthesis. We provide a molecularly designed sol–gel method that converts zinc–fumarate coordination networks into two-dimensional ZnO–carbon nanosheets utilizing solely aqueous precursors and mild annealing temperatures (400–600 °C). This method utilizes fumaric acid as a dicarboxylate linker and polyvinylpyrrolidone (PVP) as a structural carbon source to produce ultrathin wurtzite ZnO nanosheets embedded inside an amorphous carbon matrix. The resultant ZnO-C hybrid achieves nearly complete methylene blue degradation within 10 min under UV-A illumination, demonstrating first-order kinetics and outstanding recyclability. Compared with commercial ZnO, the ZnO–C nanosheets exhibit comparable rapid photocatalytic degradation, enhanced adsorption behavior, a porous nanosheet morphology, and an integrated ZnO–carbon interfacial structure. These findings provide a viable molecular-templating approach to fabricating various metal oxide–carbon photocatalysts and underscore substantial enhancements in semiconductor efficacy in eco-friendly water treatment systems.

Ozcan, Muca [ORNL] (ORCID:0000000320020474)↗
DOE OSTI2022

Tailoring the Thickness‐Dependent Optical Properties of Conducting Nitrides and Oxides for Epsilon‐Near‐Zero‐Enhanced Photonic Applications

Abstract The unique properties of the emerging photonic materials, conducting nitrides and oxides, especially their tailorability, large damage thresholds, and, importantly, the so‐called epsilon‐near‐zero (ENZ) behavior, have enabled novel photonic phenomena spanning optical circuitry, tunable metasurfaces, and nonlinear optical devices. This work explores direct control of the optical properties of polycrystalline titanium nitride (TiN) and aluminum‐doped zinc oxide (AZO) by tailoring the film thickness, and their potential for ENZ‐enhanced photonic applications. This study demonstrates that TiN–AZO bilayers support Ferrell–Berreman modes using the thickness‐dependent ENZ resonances in the AZO films operating in the telecom wavelengths spanning from 1470 to 1750 nm. The bilayer stacks also act as strong light absorbers in the ultraviolet regime using the radiative ENZ modes and the Fabry–Perot modes in the constituent TiN films. The studied Berreman resonators exhibit optically induced reflectance modulation of 15% with picosecond response time. Together with the optical response tailorability of conducting oxides and nitrides, using the field enhancement near the tunable ENZ regime can enable a wide range of nonlinear optical phenomena, including all‐optical switching, time refraction, and high‐harmonic generation.

Saha, Soham↗
DOE OSTI2022

Fabrication of High Surface Area Microporous ZnO from ZnO/Carbon Sacrificial Composite Monolith Template

Fabrication of porous materials from the standard sacrificial template method allows metal oxide nanostructures to be produced and have several applications in energy, filtration and constructing sensing devices. However, the low surface area of these nanostructures is a significant drawback for most applications. Here, we report the synthesis of ZnO/carbon composite monoliths in which carbon is used as a sacrificial template to produce zinc oxide (ZnO) porous nanostructures with a high specific surface area. The synthesized porous oxides of ZnO with a specific surface area of 78 m2/g are at least one order of magnitude higher than that of the ZnO nanotubes reported in the literature. The crucial point to achieving this remarkable result was the usage of a novel ZnO/carbon template where the carbon template was removed by simple heating in the air. As a high surface area porous nanostructured ZnO, these synthesized materials can be useful in various applications including catalysis, photocatalysis, separation, sensing, solar energy harvest and Zn-ion battery and as supercapacitors for energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High‐Order Nonlinear Frequency Conversion in Transparent Conducting Oxide Thin Films

The study of conductive oxides has gained momentum within the photonics community due to their unique linear and nonlinear optical properties. Despite recent experiments reporting on high harmonic generation from thin films, the optical/electronic behavior of these compounds at the nanoscale is still not fully understood due to the lack of a suitable theoretical model. In the present work, aluminum zinc oxide is excited near its epsilon-near-zero crossing point using incident femtosecond pulses having peak power densities in the 1 TW cm −2 range. A relatively efficient frequency up-conversion including even and odd harmonics up to the seventh order is observed. A hydrodynamic-Maxwell theoretical approach is adopted, capable of simultaneously taking into account linear and nonlinear dispersions, nonlocal effects, surface, magnetic, and bulk nonlinearities in a spectral region that spans over two and a half octaves from the UV to the NIR region. The study enables a deeper understanding of the fundamental material parameters regulating optical nonlinearities, providing important insights to engineer this class of materials for applications in sensing, ultra-fast physics, and spectroscopy.

material modeling↗