Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Thermal stability and magnetization switching of composite free layer with perpendicular magnetic anisotropy

We present a micromagnetic study of a ferromagnetically exchange-coupled composite free layer design for perpendicular magnetic tunnel junctions. The thermal stability factor and critical switching current density depend on the exchange coupling strength and effective anisotropy ratio between the sublayers of the composite free layer. The energy barrier increases with an increase of the exchange coupling strength until it reaches a plateau in the strong-coupling limit. An optimal exchange coupling strength exists that leads to the minimal critical switching current and a significant improvement of the figure of merit defined as the ratio between the energy barrier and critical switching current. This behavior is obtained for smaller device sizes with uniform reversal and larger sizes with domain wall reversal.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal stability of dopants in boron carbide

Undoped (B 4 C), B rich (B 5.5 C), and B/Si co-doped (Si-B 6.5 C) boron carbides were annealed at 500 °C for up to 21 days to investigate the thermal stability of primary dopants, B and Si. Structural changes associated with dedoping were investigated by X-ray diffraction (XRD) and Raman spectroscopy. The stable phase B 4 C showed no microstructural or lattice parameter changes. Similarly, lattice parameters of B 5.5 C remained constant, suggesting that B dopant is stable at the given conditions. However, the shortened lattice parameters and reduced Si content of Si-B 6.5 C over the annealing time indicated that Si dopant was in a metastable state at the annealing temperature. Consequently, Si dedoping led to an increase in amorphization (a loss of local crystalline order) which degrades the ballistic performance of boron carbide. The insight highlights the importance of Si dopant in boron carbide and suggests that rapid processing may be necessary to retain more silicon for better performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A High-Ceramic-Loading LATP–PVDF–Al 2 O 3 Composite Film for Lithium-Ion Batteries With Favorable Porous Microstructure and Enhanced Thermal Stability

A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Ultrafine-grained Al-Mg-Zr Alloy Processed by Shear-Assisted Extrusion with High Thermal Stability

Shear-assisted processing and extrusion (ShAPE) is used to consolidate Al-4.2Mg-1.6Zr-0.25Si-0.1Fe (wt.%) powders. The extruded alloy exhibits: (i) near-zero porosity; (ii) an attractive combination of tensile yield strength (~220 MPa), ultimate strength (330 MPa) and elongation (>20%); and (iii) excellent thermal stability at 400 ºC. The ultra-fine grain size in the gas-atomized powders – created and stabilized by primary L12-Al3Zr submicron precipitates - is maintained after consolidation and subsequent exposure at 400 ºC, contributing twice as much to strength as Mg in solid-solution. Electron microscopy reveals the microstructure of the L12-Al3Zr precipitates, and other precipitates (Mg2Si and Al3Fe) and dispersoids (oxides).

ShAPE, Friction Extrusion, aluminum powder, Shear ↗
DOE OSTI2024

Bromine Incorporation Affects Phase Transformations and Thermal Stability of Lead Halide Perovskites

Mixed-cation and mixed-halide lead halide perovskites show great potential for their application in photovoltaics. Many of the high-performance compositions are made of cesium, formamidinium, lead, iodine, and bromine. However, incorporating bromine in iodine-rich compositions and its effects on the thermal stability of the perovskite structure has not been thoroughly studied. In this work, we study how replacing iodine with bromine in the state-of-the-art Cs 0.17 FA 0.83 PbI 3 perovskite composition leads to different dynamics in the phase transformations as a function of temperature. Through a combination of structural characterization, cathodoluminescence mapping, X-ray photoelectron spectroscopy, and first-principles calculations, we reveal that the incorporation of bromine reduces the thermodynamic phase stability of the films and shifts the products of phase transformations. Our results suggest that bromine-driven vacancy formation during high temperature exposure leads to irreversible transformations into PbI 2 , whereas materials with only iodine go through transformations into hexagonal polytypes, such as the 4H-FAPbI 3 phase. This work sheds light on the structural impacts of adding bromine on thermodynamic phase stability and provides new insights into the importance of understanding the complexity of phase transformations and secondary phases in mixed-cation and mixed-halide systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Adaptive thermal stabilization of an integrated photonic spectrometer using parasitic interference fringes

Parasitic fringe drift from unwanted scatterings limits the long-term stability of waveguide-based optical spectrometers. Yet their spectral features provide relevant information that can be used to improve performance of the spectrometer. We show that fringe drift can be extracted and utilized to perform accurate thermal stabilization, especially in the case of integrated waveguide sensors. In this Letter, effective stabilization of a methane silicon photonic sensor is demonstrated, and significant reduction in fringe noise is clearly observed.

Teng, Chu C.↗
DOE OSTI2023

In-situ transmission electron microscopy investigation on surface oxides thermal stability of niobium

Niobium is commonly used for superconducting quantum systems as readout resonators, capacitors, and interconnects. Structural defects at the Nb/Si and air/Nb interface may be a major source of two-level systems (TLS), which are detrimental to the device's coherence time. Thus, identifying and understanding the microscopic origin of possible TLS in Nb-based devices and their relationship to processing is key to superconducting qubit performance improvement. Here this work studied the structure and thermal stability of surface oxide on physical vapor deposited Nb films on Si wafers, using aberration-corrected (scanning) transmission electron microscopy and spectroscopy. Here, all Nb films exhibit columnar growth with strong [110] textures. After in-situ heating of the heterostructure at 360 °C inside the microscope, the initial amorphous niobium surface oxides decompose into face-centered cubic Nb nanograins in the amorphous Nb-O matrix, which may reduce microwave dissipation. Despite changes in the microstructure and chemistry of the niobium oxide surface layer due to heat treatment, the interface between the Nb and the surface oxide layer remains almost unchanged. Our comprehensive study of the Nb surface oxide decomposition mechanism may guide future superconducting qubit device optimization through interfacial scattering center and TLS minimization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Thermal Stability Testing of LANA.75

Savannah River Site has used the metal hydride LaNi 4.25 Al 0.75 (LANA.75) in the Tritium Facilities for over two decades. LANA.75 beds store significant quantities of tritium but have a limited service life due to the radiolytic decay of tritium to 3He within the metal matrix. It has been shown that the isotherm performance of a tritium-aged LANA.75 sample can be restored by heating under vacuum. Additional investigation is needed to ensure there are no unexpected changes to the hydride before this technique is employed in full-scale beds in the Tritium Facilities. In addition, it is necessary to verify the regenerable behavior and thermal stability of LANA.75 on a small scale prior to it being implemented on a large scale. In this work, a non-tritiated bench-scale LANA.75 sample was held at 750°C under vacuum for 200 h to simulate exposure to multiple restoration evolutions. Hydride isotherm performance, chemical composition, crystallinity, and morphology are compared between the pre-restorative and post-restorative testing samples. No significant changes were observed in composition or crystallinity. Comparison of pre-anneal and post-anneal isotherms showed that performance improved rather than deteriorated during the evolution. Scanning electron microscopy analysis showed small growths on the particle surface after exposure to regeneration conditions. Additional testing will be required to determine the cause of these growths.

08 HYDROGEN↗
DOE OSTI2023

Improved Thermal Stability of Oxysulfide Glassy Solid-State Electrolytes

In this study, the crystallization kinetics of (oxy)sulfide 70Li 2 S·(30-x)P 2 S 5 ·xP 2 O 5 (x = 0, 2, 5) solid-state electrolytes are reported. It was found that 5 mol% P 2 O 5 glass co-former slowed the crystallization rate of the Li 7 P 3 S 11−x/4 O x/4 ceramic phase by a factor of 10. After 10 min at 230 °C, a 70Li 2 S·30P 2 S 5 sulfide glass was 92% devitrified whereas a 70Li 2 S·25P 2 S 5 ·5P 2 O 5 oxysulfide glass was only 8% devitrified. The improved thermal stability of oxysulfide glasses was then utilized to demonstrate the fabrication of a standalone, reinforced SSE separator by hot pressing. More importantly, it was recognized that the microstructure of 70Li 2 S·25P 2 S 5 ·5P 2 O 5 oxysulfide SSE separators could be modified by hot pressing without changing ionic conductivity. This result was achieved because the precipitation of a superionically conductive Li 7 P 3 S 11−x/4 O x/4 ceramic phase was limited. A study was then conducted to determine what effect microstructure has on the susceptibility of SSE separators to shorting by lithium metal penetration. Hot-pressed separators were found to be more susceptible to shorting than cold-pressed separators. X-ray Computer Tomography (XCT) of post-mortem samples showed that hot-pressed samples failed by transverse microcrack pathways, which underscores the importance of low defect density in dense SSE separators.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Regulating Catalytic Properties and Thermal Stability of Pt and PtCo Intermetallic Fuel-Cell Catalysts via Strong Coupling Effects between Single-Metal Site-Rich Carbon and Pt

Developing low platinum-group-metal (PGM) catalysts for the oxygen reduction reaction (ORR) in proton-exchange membrane fuel cells (PEMFCs) for heavy-duty vehicles (HDVs) remains a great challenge due to the highly demanded power density and long-term durability. Here, this work explores the possible synergistic effect between single Mn site-rich carbon (Mn SA -NC) and Pt nanoparticles, aiming to improve intrinsic activity and stability of PGM catalysts. Density functional theory (DFT) calculations predicted a strong coupling effect between Pt and MnN 4 sites in the carbon support, strengthening their interactions to immobilize Pt nanoparticles during the ORR. The adjacent MnN 4 sites weaken oxygen adsorption at Pt to enhance intrinsic activity. Well-dispersed Pt (2.1 nm) and ordered L1 2 -Pt 3 Co nanoparticles (3.3 nm) were retained on the Mn SA -NC support after indispensable high-temperature annealing up to 800 °C, suggesting enhanced thermal stability. Both PGM catalysts were thoroughly studied in membrane electrode assemblies (MEAs), showing compelling performance and durability. The Pt@Mn SA -NC catalyst achieved a mass activity (MA) of 0.63 A mg Pt –1 at 0.9 V iR-free and maintained 78% of its initial performance after a 30,000-cycle accelerated stress test (AST). The L1 2 -Pt 3 Co@Mn SA -NC catalyst accomplished a much higher MA of 0.91 A mg Pt –1 and a current density of 1.63 A cm –2 at 0.7 V under traditional light-duty vehicle (LDV) H 2 –air conditions (150 kPa abs and 0.10 mg Pt cm –2 ). Furthermore, the same catalyst in an HDV MEA (250 kPa abs and 0.20 mg Pt cm –2 ) delivered 1.75 A cm –2 at 0.7 V, only losing 18% performance after 90,000 cycles of the AST, demonstrating great potential to meet the DOE targets.

25 ENERGY STORAGE↗
DOE OSTI2021

Kilovolt Tri-Gate GaN Junction HEMTs with High Thermal Stability

The lack of reports on the high-temperature performance of tri-gate GaN power HEMTs has raised serious concern on their competitiveness. This work demonstrates the first normally-off tri-gate GaN HEMT that can block kilovolts at 150 °C and zero gate bias. The key enabling device design is a new type of tri-gate, the junction tri-gate, which comprises p-n junction wrapping around AlGaN/GaN fins in the gate region. At 150 °C, the GaN tri-gate junction HEMT (Tri-JHEMT) retains strong gate control and stable threshold voltage, while the traditional tri-gate metal-insulator-semiconductor (MIS) HEMTs fabricated on the same wafer shows a large threshold voltage shift and inferior capabilities of voltage blocking. These results show the excellent thermal stability of GaN Tri-JHEMTs and their great potentials for power electronics applications.

Ma, Yunwei↗
DOE OSTI2022

Pressure Engineering Promising Transparent Oxides with Large Conductivity Enhancement and Strong Thermal Stability

Abstract Transparent conducting oxides (TCO) with high electrical conductivity and high visible light transparency are desired for a wide range of high‐impact engineering. Yet, usually, a compromise must be made between conductivity and transparency, limiting the practical application of a TCO to the next level. Furthermore, TCO performance is highly sensitive to composition, so conventional synthesis methods, such as chemical doping, cannot unravel the mysteries of the quantitative structure–performance relationship. Thus, improving the fundamental understanding or creating materials‐by‐design has limited success. Here, a strategy is proposed to modulate the lattice and electronic and optical properties precisely by applying pressure on a TCO. Strikingly, after compression–decompression treatment on the indium titanium oxides (ITiO), a highly transparent and metastable phase with two orders of magnitude enhancement in conductivity is synthesized from an irreversible phase transition. Moreover, this phase possesses previously unattainable filter efficiency on hazardous blue light up to 600 °C, providing potential for healthcare‐related applications with strong thermal stability up to 200 °C. These results demonstrate that pressure engineering is a clean and effective tool for tailoring functional materials that are not achievable by other means, providing an exciting alternative property‐tuning dimension in materials science.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermal Stability of the Dot-in-Well Gain Medium for Photonic Crystal Surface Emitting Lasers

Self-assembled quantum dots (QDs) embedded in InGaAs quantum wells (QWs) are used as active regions for photonic-crystal surface-emitting lasers (PCSELs). An epitaxial regrowth method is developed to fabricate the dot-in-well (DWELL) PCSELs. Here, the epitaxial regrowth starts with the growth of a partial laser structure containing bottom cladding, waveguide, active region, and the photonic crystal (PC) layer. The PC layer is patterned to realize the cavity. Subsequently a top cladding layer is regrown to complete the laser structure. During the regrowth of the top cladding layer, the partial laser structure is subjected to high growth temperatures in excess of 600 °C resulting in an unintentional annealing of the active region. This annealing of the active region can alter the QDs by changing their size resulting in a blue shift in photoluminescence (PL) and narrowing PL emission. This effect results in the misaligning of the gain peak and the cavity resonance, resulting in sub-optimal lasing performance. DWELL active regions are known to have better thermal stability compared to both QDs and QWs and could be an ideal candidate for regrown PCSELs. We successfully demonstrate an optically-pumped epitaxially-regrown DWELL PCSEL with an emission wavelength of 1230 nm operating at room temperature. Furthermore, the DWELL active region shows excellent emission wavelength stability and intensity despite the high temperature regrowth process.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Diffused morphotropic phase boundary in relaxor-PbTiO 3 crystals: High piezoelectricity with improved thermal stability

Solid solution ferroelectrics are the most widely used piezoelectric material for numerous electromechanical applications, including sensors, actuators, and transducers. A milestone in ferroelectric research is the discovery of the morphotropic phase boundary that was first reported in Pb(Zr x Ti 1–x )O 3 , which has been extensively solicited to improve the performance of various solid solution ferroelectrics, including those having the highest piezoelectricity known today. However, due to the inherent correlation between phase transition and thermodynamic imbalance, the efforts of building the phase boundary encounter the challenge that high performance materials are generally accompanied by property instability. In this paper, we report a comprehensive study on the crystalline symmetry and polar nano-regions in relaxor-PbTiO 3 crystals by synchrotron measurements and property characterizations. In contrast to the common belief that the morphotropic phase boundary is a narrow composition region, the morphotropic phase boundary in ternary Pb(In 1/2 Nb 1/2 )O 3 -Pb(Mg 1/3 Nb 2/3 )O 3 -PbTiO 3 is demonstrated as an extensive region covering at least 9% of the PbTiO 3 content. Such a diffused morphotropic phase boundary is associated with the intensive interaction of polar nano-regions, leading to high piezoelectricity (>1500 pC/N) with greatly improved thermal stability, where the piezoelectric variation is ~90% over the temperature range of 273–373 K, which is about a factor of 3 lower compared to its binary counterpart Pb(Mg 1/3 Nb 2/3 )O 3 -PbTiO 3 . This work sheds light on the fundamental understanding of nanoscale inhomogeneity and macroscopic symmetry in relaxor-PbTiO 3 , and successfully interlinks the structure and properties in complex solid solutions. The existence of a diffused morphotropic phase boundary is also expected to benefit other ferroic systems beyond ferroelectrics, such as ferromagnetic and multiferroic materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

A far‐red‐emitting (Gd,Y) 3 (Ga,Al) 5 O 12 :Mn 2+ ceramic phosphor with enhanced thermal stability for plant cultivation

Abstract As for plants, far‐red (FR) light with wavelength from 700 nm to 740 nm is critical for processes of photosynthesis and photomorphogenesis. Light‐controlled development depends on light to control cell differentiation, structural and functional changes, and finally converge into the formation of tissues and organs. Phosphor converted FR emission under LED excitation is a cost‐effective and high‐efficient way to provide artificial FR light source. With the aim to develop an efficient FR phosphor that can promote the plant growth, a series of gadolinium yttrium gallium garnet (GYGAG) transparent ceramic phosphors co‐doped with Mn 2+ and Si 4+ have been fabricated via chemical co‐precipitation method, followed sintered in O 2 and hot isostatic pressing in this work. Under UV excitation, the phosphor exhibited two bright and broadband red emission spectra due to Mn 2+ : 4 T 1 → 6 A 1 spin‐forbidden transition, and one of which located in the right FR region. And then, Ce 3+ ions were co‐doped as the activator to enhance the absorption at blue light region and the emission of Mn 2+ . It turns out that the emission band of GYGAG transparent ceramic phosphors matches well with the absorption band of phytochrome P FR , which means they are promising to be applied in plant cultivation light‐emitting diodes (LEDs) for modulating plant growth. Besides, the thermal stability of this material was investigated systematically, and an energy transferring model involves defects was also proposed to explain the phenomenon of abnormal temperature quenching.

Qiu, Xuting↗
DOE OSTI2022

Thermal stability of antiferroelectric-like Al:HfO 2 thin films with TiN or Pt electrodes

HfO 2 -based antiferroelectric-like thin films are increasingly being considered for commercial devices. However, even with initial promise, the temperature sensitivity of electrical properties such as loss tangent and leakage current remains unreported. 50 nm thick, 4 at. % Al-doped HfO 2 thin films were synthesized via atomic layer deposition with both top and bottom electrodes being TiN or Pt. A study of their capacitance vs temperature showed that the Pt/Al:HfO 2 /Pt had a relative dielectric permittivity of 23.30 ± 0.06 at room temperature with a temperature coefficient of capacitance (TCC) of 78 ± 86 ppm/°C, while the TiN/Al:HfO 2 /TiN had a relative dielectric permittivity of 32.28 ± 0.14 at room temperature with a TCC of 322 ± 41 ppm/°C. The capacitance of both devices varied less than 6% over 1 to 1000 kHz from –125 to 125 °C. Both capacitors maintained loss tangents under 0.03 and leakage current densities of 10 –9 –10 –7 A/cm 2 between –125 and 125 °C. The TiN/Al:HfO 2 /TiN capacitor maintained an energy storage density (ESD) of 18.17 ± 0.79 J/cm 3 at an efficiency of 51.79% ± 2.75% over the –125 to 125 °C range. The Pt/Al:HfO 2 /Pt capacitor also maintained a stable ESD of 9.83 ± 0.26 J/cm 3 with an efficiency of 62.87% ± 3.00% over the same temperature range. Finally, such low losses in both capacitors along with their thermal stability make antiferroelectric-like, Al-doped HfO 2 thin films a promising material for temperature-stable microelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced Thermal Stability of Conductive Mercury Telluride Colloidal Quantum Dot Thin Films Using Atomic Layer Deposition

Colloidal quantum dots (CQDs) are valuable for their potential applications in optoelectronic devices. However, they are susceptible to thermal degradation during processing and while in use. Mitigating thermally induced sintering, which leads to absorption spectrum broadening and undesirable changes to thin film electrical properties, is necessary for the reliable design and manufacture of CQD-based optoelectronics. Here, low-temperature metal–oxide atomic layer deposition (ALD) was investigated as a method for mitigating sintering while preserving the optoelectronic properties of mercury telluride (HgTe) CQD films. ALD-coated films are subjected to temperatures up to 160 °C for up to 5 h and alumina (Al 2 O 3 ) is found to be most effective at preserving the optical properties, demonstrating the feasibility of metal–oxide in-filling to protect against sintering. HgTe CQD film electrical properties were investigated before and after alumina ALD in-filling, which was found to increase the p-type doping and hole mobility of the films. The magnitude of these effects depended on the conditions used to prepare the HgTe CQDs. With further investigation into the interaction effects of CQD and ALD process factors, these results may be used to guide the design of CQD–ALD materials for their practical integration into useful optoelectronic devices.

36 MATERIALS SCIENCE↗