Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “testing guide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Deep Learning for Rapid Analysis of Spectroscopic Ellipsometry Data

High‐throughput experimental approaches to rapidly develop new materials require high‐throughput data analysis methods to match. Spectroscopic ellipsometry is a powerful method of optical properties characterization, but for unknown materials and/or layer structures the data analysis using traditional methods of nonlinear regression is too slow for autonomous, closed‐loop, high‐throughput experimentation. Herein, three methods (termed spectral, piecewise, and pointwise) of spectroscopic ellipsometry data analysis based on deep learning are introduced and studied. After initial training, the incremental time for inferring optical properties can be a thousand times faster than traditional methods. Results for multilayer sample structures with optically isotropic materials are presented, appropriate for high‐throughput studies of thin films of phase‐change materials such as GeSbTe (GST) alloys. Results for studies on highly birefringent layered materials are also presented, exemplified by the transition metal dichalcogenide MoS 2 . How the materials under test and the experimental objectives may guide the choice of analysis methods are discussed. The utility of our approach is demonstrated by analyzing data measured on a composition spread of GeSbTe phase‐change alloys containing 177 distinct compositions, and identifying the composition with optimal phase‐change figure of merit in only 1.4 s of analysis time.

Li, Yifei↗
DOE OSTI2023

MCNP ® Code V.6.3.0 Release Notes

The Monte Carlo N-Particle ® (MCNP ® ) code is a general-purpose, continuous-energy, generalized geometry, time-dependent, radiation transport code developed by the MCNP development team. The MCNP calculations provide predictive capabilities that can replace expensive or impossible-to perform experiments. Specific application problems include simulations of experimental diagnostics, intrinsic radiation, radiation detection and measurement, criticality safety, nuclear threat reduction and response, radiation health protection, nuclear weapons effects, and nuclear forensics. This MCNP code, version 6.3.0, follows the MCNP6.2.0 version. Since the release of MCNP6.2.0, many changes have been made to the MCNP code. These changes include new or improved features, a new build system, code enhancement and modernization, and bug fixes. The MCNP code, version 6.3.0, theory and user input information is documented in MCNP ® Code Version 6.3.0 Theory & User Manual, the build guidance for various platforms is documented in MCNP ® Code Version 6.3.0 Build Guide, and the verification and validation testing for various application benchmark test suites is documented in MCNP ® Code Version 6.3.0 Verification & Validation Testing.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Assessment and Coordination of EVSE Cybersecurity Standards

Cybersecurity certification programs for Electric Vehicle Supply Equipment (EVSE) are fragmented due to no single certification covering all aspects of the device and additionally the existence of multiple programs and under different levels of regulation. These devices are also confronted by the intricate assembly of product software, firmware, and hardware. Devices contain both logical and physical interfaces. These multifaceted devices have vulnerabilities at many levels and interconnect with other potentially vulnerable systems including the electric vehicle, the cloud where data and payment information are stored, and the electric grid and electric grid equipment including utilities. Of the EVSE certification programs that are found, none are directly for the cybersecurity of EVSE. Many standards are for safety, specifically battery safety, some are cybersecurity standards for other types of equipment and can be modeled for EVSE. In specific, ISA/IEC 62443 is found to be significantly in line with EVSE security needs and will be used in future testing to certify EVSE and help guide the project to demonstrate where gaps exist, where strengths lie in the standard and how this can be used to lead the certification efforts in harmonizing EVSE cybersecurity standards. In addition, there are multiple efforts that are currently seeking to build EVSE standards or revise existing standards to address gaps. This effort is seeking to establish a cybersecurity program for EVSE that will inform customers and help increase the level of security across products and state EVSE procurements to achieve consistency across different jurisdictions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

MCNP® Code Version 6.3.1 Release Notes

The Monte Carlo N-Particle® (MCNP® ) code is a general-purpose, continuous-energy, generalized-geometry, time-dependent, radiation transport code developed by the MCNP development team. MCNP calculations provide predictive capabilities that can replace expensive or impossible-to-perform experiments. Specific application problems include simulations of experimental diagnostics, intrinsic radiation, radiation detection and measurement, criticality safety, nuclear threat reduction and response, radiation health protection, nuclear weapons effects, and nuclear forensics. This MCNP code, version 6.3.1, follows the MCNP6.3.0 version. Since the release of MCNP6.3.0, a variety of bug fixes and code enhancements have been completed for MCNP6.3.1. A few new features have also been added to this release to support both ongoing research and the release of the latest ENDF/B-VIII.1 nuclear data library. The MCNP code, version 6.3.1, theory and user input information is documented in MCNP® Code Version 6.3.1 Theory & User Manual, the build guidance for various platforms is documented in MCNP® Code Version 6.3.1 Build Guide, and the verification and validation testing for various application benchmark test suites is documented in MCNP® Code Version 6.3.1 Verification & Validation Testing.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Wave Tank Testing Report for Controls Validation of a Heaving Point Absorber

The core objectives of this project is to improve the power capture of three different wave energy conversion (WEC) devices by more than 50% using an advanced control system and validate the attained improvements using wave tank and full scale testing. In parallel, we will bring along the development of a wave prediction system that is required to enable effective control and test it at full scale. The purposes of this report are to: 1. Plan and document the 1/25th scale device testing at the wave-tank facility; 2. Document the test article, setup and methodology, sensor and instrumentation, mooring, electronics, wiring, and data flow and quality assurance; 3. Communicate the testing results between the associated members; 4. Facilitate reviews that will help to ensure all aspects (risk, safety, testing procedures, etc.); 5. Provide a systematic guide to setting up, executing and decommissioning the experiment.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Stream Temperature Prediction in a Shifting Environment: Explaining the Influence of Deep Learning Architecture

Stream temperature is a fundamental control on ecosystem health. Recent efforts incorporating process guidance into deep learning models for predicting stream temperature have been shown to outperform existing statistical and physical models. This performance is in part because deep learning architectures can actively learn spatiotemporal relationships that govern how water and energy propagate through a river network. However, exploration of how spatiotemporal awareness and process guidance influence a model's generalizability under shifting environmental conditions such as climate change is limited. Here, we use Explainable Artificial Intelligence (XAI) to interrogate how differing deep learning architectures affect a model's learned spatial and temporal dependencies, and how those learned dependencies affect a model's ability to maintain high accuracy when applied to unseen environmental conditions. Using the Delaware River Basin in the northeastern United States as a test case, we compare two spatiotemporally aware process–guided deep learning models for predicting stream temperature (a recurrent graph convolution network—RGCN, and a temporal convolution graph model—Graph WaveNet). Both models achieve equally high predictive performance when testing data are well represented in the training data (test root mean squared errors of 1.64°C and 1.65°C); however, Graph WaveNet significantly outperforms RGCN in 4 out of 5 experiments where test partitions represent different types of unseen environmental conditions. XAI results show that the architecture of Graph WaveNet leads to learned spatial relationships with greater fidelity to physical processes, and that this fidelity improves the generalizability of the model when applied to shifting and/or unseen environmental conditions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

ATR User Guide

An update of the 2009 ATR NSUF User Guide (INL/EXT-08-14709), focusing on the current thermal irradiation capabilities of the Advanced Test Reactor. It is also largely based on the 2002 ATR Handbook (INEEL/EXT-02-01064), including authors Frances Marshall and Glen Longhurst, among other contributors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Digital Twin Model for Advanced Manufacture of a Rotating Detonation Engine Injector

A digital twin material model (DTMM) of an additive manufacturing (AM) process was created to advance the state of the art in rotating detonation engine (RDE) injector design. Current RDE injectors are designed with large pressure drops, enabling a stable and repeatable combustion process. However, this comes at the cost of system efficiency. For the technology to transition to commercial fossil-based power generation, it is important to develop injectors with reduced flow losses. Low-loss injectors are difficult to design and manufacture with conventional manufacturing techniques. AM enables new design options, but the AM manufacturing process must be thoroughly understood to result in a robust design. A DTMM provides the necessary insight by defining the cause-effect relationships between process parameters, microstructure features, and properties. Therefore, a DTMM to support the design and manufacturing process was developed and applied to the design of a new additively manufactured low-loss injector. The injector combustion behavior was characterized through hot-fire tests, and mechanical performance was compared to the DTMM predictions. The two project goals were the successful development of the DTMM and the demonstration of an improved RDE injector design. The RDE injector design and DTMM developments occurred on parallel but dependent paths. The injector was designed to reduce pressure drop by increasing the cross-sectional flow area ratio between the injector air passages and the combustor annulus. This resulted in less structural material, raising the concern that thin members would be susceptible to high-cycle fatigue (HCF) under the periodic loading inherent to an RDE. It was most important for the DTMM to predict behavior in these features; therefore, the injector design concept guided the material thicknesses used in fatigue tests. The DTMM development started by manufacturing a series of coupons over the range of possible AM process variations. A design-of-experiment approach was used to select which process variable combinations gave the most efficient coverage relevant to the injector design space. The microstructure in each of these coupons was characterized, and then computational methods were used to create a numerical model of the correlation between process variables and microstructure. Next, a set of HCF samples were tested to calibrate existing models that map microstructure to HCF performance. Together, these two links formed the DTMM that calculates HCF behavior from AM process variables. Two injector prototypes were additively manufactured. The first injector design strategy aggressively pursued low-loss performance by substantially increasing the oxidizer flow area. The combination of manufacturing lead times and the fatigue testing schedule meant that the DTMM was not available when building this first prototype. Therefore, its process parameters were chosen based on a manual review of the available coupon data. This prototype was built successfully and evaluated in 58 combustion tests. Sustained detonation was achieved with remarkably reduced pressure loss, and some tests even displayed pressure loss characteristics similar to conventional gas turbine combustors. This achieved the project goal of improving RDE injector design. The second injector was manufactured according to the optimized parameters predicted by the DTMM. The flow area modifications of this injector were less aggressive than the first injector since demonstrating low pressure loss was not an objective of the second hot-fire test series. Rather, the test objective was to cause high cycle fatigue failure in the part due to periodic loading from the rotating detonation wave. The observed number of cycles to failure was to be compared to the number predicted by the DTMM and thereby assess the utility of the DTMM in component design. However, the required level of vibration was not obtained during combustion. Therefore, high cycle fatigue was not experienced in the hot-fire tests of the second injector. Fatigue data was obtained by further testing the second injector in a conventional HCF test apparatus. The injector demonstrated HCF strength above the DTMM prediction. In fact, it did not fail and testing was only discontinued due to reaching the end of the period of performance. This points to some success in the project’s primary goal of successfully developing and applying the DTMM to a component design. Implementing the DTMM recommendations for optimal processing parameters led to a part with acceptable properties. The DTMM was also shown to be an efficient correlator of data and to provide insight into the relationship between process settings, microstructure, and property performance. However, the failure of the DTMM prediction to match the experimental result of the injector fatigue test also points to the need to include significantly more data in the model development. In this project, coupons made with identical processing parameters exhibited drastically different properties from each other and from the injector part, which clearly influences the accuracy of a model that predicts performance based on parameters. Uncertainties in the build process must be quantified to develop more robust models. A denser and broader matrix of coupon process and geometry variations, several repeated builds of every point, more in-situ build process measurements, and direct observation of tensile and HCF sample microstructure (as opposed to separate microstructure specimens) are recommendations to improve future AM modeling efforts.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Battery Abuse Testing

Abuse tests are designed to determine the safe operating limits of HEV\PHEV energy storage devices. Testing is intended to achieve certain worst-case scenarios to yield quantitative data on cell\module\pack response, allowing for failure mode determination and guiding developers toward improved materials and designs. Standard abuse tests with defined start and end conditions are performed on all devices to provide comparison between technologies. New tests and protocols are developed and evaluated to more closely simulate real-world failure conditions. While robust mechanical models for vehicles and vehicle components exist, there is a gap for mechanical modeling of EV batteries. The challenge with developing a mechanical model for a battery is the heterogeneous nature of the materials and components (polymers, metals, metal oxides, liquids). This year saw the stand up of a new drop tower tester capable of providing dynamic mechanical test results.

25 ENERGY STORAGE↗
DOE OSTI2021

I.6.C Battery Safety Testing

Abuse tests are designed to determine the safe operating limits of HEV\PHEV energy storage devices. Testing is intended to achieve certain worst-case scenarios to yield quantitative data on cell\module\pack response, allowing for failure mode determination and guiding developers toward improved materials and designs. Standard abuse tests with defined start and end conditions are performed on all devices to provide comparison between technologies. New tests and protocols are developed and evaluated to more closely simulate real world failure conditions. While robust mechanical models for vehicles and vehicle components exist, there is a gap for mechanical modeling of EV batteries. The challenge with developing a mechanical model for a battery is the heterogeneous nature of the materials and components (polymers, metals, metal oxides, liquids).

25 ENERGY STORAGE↗
DOE OSTI2025

Low responsiveness of machine learning models to critical or deteriorating health conditions

Machine learning (ML) based mortality prediction models can be immensely useful in intensive care units. Such a model should generate warnings to alert physicians when a patient’s condition rapidly deteriorates, or their vitals are in highly abnormal ranges. Before clinical deployment, it is important to comprehensively assess a model’s ability to recognize critical patient conditions. We develop multiple medical ML testing approaches, including a gradient ascent method and neural activation map. We systematically assess these machine learning models’ ability to respond to serious medical conditions using additional test cases, some of which are time series. Guided by medical doctors, our evaluation involves multiple machine learning models, resampling techniques, and four datasets for two clinical prediction tasks. We identify serious deficiencies in the models’ responsiveness, with the models being unable to recognize severely impaired medical conditions or rapidly deteriorating health. For in-hospital mortality prediction, the models tested using our synthesized cases fail to recognize 66% of the injuries. In some instances, the models fail to generate adequate mortality risk scores for all test cases. Our study identifies similar kinds of deficiencies in the responsiveness of 5-year breast and lung cancer prediction models. Using generated test cases, we find that statistical machine-learning models trained solely from patient data are grossly insufficient and have many dangerous blind spots. Most of the ML models tested fail to respond adequately to critically ill patients. How to incorporate medical knowledge into clinical machine learning models is an important future research direction.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

The dual of non-extremal area: differential entropy in higher dimensions

The Ryu-Takayanagi formula relates entanglement entropy in a field theory to the area of extremal surfaces anchored to the boundary of a dual AdS space. It is interesting to ask if there is also an information theoretic interpretation of the areas of non-extremal surfaces that are not necessarily boundary-anchored. In general, the physics outside such surfaces is associated to observers restricted to a time-strip in the dual boundary field theory. When the latter is two-dimensional, it is known that the differential entropy associated to the strip computes the length of the dual bulk curve, and has an interpretation in terms of the information cost in Bell pairs of restoring correlations inaccessible to observers in the strip. A general realization of this formalism in higher dimensions is unknown. We first prove a no-go theorem eliminating candidate expressions for higher dimensional differential entropy based on entropic c-theorems. Then we propose a new formula in terms of an integral of shape derivatives of the entanglement entropy of ball shaped regions. Our proposal stems from the physical requirement that differential entropy must be locally finite and conformally invariant. Demanding cancelation of the well-known UV divergences of entanglement entropy in field theory guides us to our conjecture, which we test for surfaces in AdS 4 . Our results suggest a candidate c-function for field theories in arbitrary dimensions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Thermal-shock experiments for separate-effects validation of UO 2 fuel fracture models

Because of the important role that fracture plays in the behavior of ceramic UO2 fuel in a nuclear reactor environment, fracture models are a major component of fuel performance codes. As with any aspect of fuel performance, it is crucial to validate these fracture models against experimental data; however, obtaining well-controlled data for conditions representative of a reactor environment is difficult. Quenching is proposed here as a relatively simple approach for using a laboratory environment to achieve conditions that approximate those of a reactor environment. In this paper, an experimental apparatus containing a single instrumented fuel pellet in a sealed section of copper tubing is developed. It is then applied to a series of seven experiments in which the apparatus is first heated to a high temperature (580-680°C) by immersion in a molten salt bath, then quenched in a cold bath (-10-4 °C). Development of these experiments was guided by numerical simulations, and post-test simulations were performed to aid in understanding the experimental behavior and assessing the accuracy of the predictions of fracture initiation and propagation. In addition, similar experiments were performed on solid copper rods to provide temperature-dependent heat transfer coefficients for use in simulations of these experiments. Here, this study demonstrates that quenching is a viable approach for generating thermal gradients representative of those in prototypical light-water reactor conditions at powers of about 5–10 kW/m. Fracture is expected to begin at these power levels, and moderate amounts of radial and axial cracking was observed in these quenching tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Plutonium migration and phase evolution in irradiated U-Pu-Zr metallic fuels: An integrated EPMA-SEM-TEM study

Constituent redistribution is a defining feature of irradiated U-Pu-Zr metallic fuels, yet its mechanisms and effects on fuel performance are not sufficiently resolved to guide model development. Although decades of irradiation testing have established broad trends, a true mechanistic understanding of constituent redistribution has not been achieved. Here, in this study, we use electron probe microanalysis (EPMA), scanning electron microscopy (SEM), and transmission electron microscopy-based (TEM) selective area electron diffraction (SAED) on a EBR-II irradiated U-19 wt.% Pu-6 wt.% Zr fuel pin cross-section to correlate the composition, porosity, and crystallographic phases formed after irradiation. Constituent redistribution is thought to consist of three distinct zones, in which uranium and zirconium migrate while plutonium remains relatively unchanged. Our EPMA results resolve eight distinct compositional regions, and more importantly, show that plutonium redistributes alongside zirconium, contrary to historical assumptions. The distribution of fission products was highly asymmetric with a few large lanthanide precipitates observed at isolated sites on the pin periphery instead of a uniform distribution of smaller precipitates around the periphery. Using thermodynamic data from TAF-ID and the measured EPMA compositions, matrix phase fractions were predicted across the fuel radius. Phase predictions based on composition did not match TEM/SAED results, which revealed a much higher fraction of α−U phase than would be expected if phases were retained from reactor temperatures. These findings highlight the need for expanded SAED phase identification to capture post-irradiation and storage effects, as well as rigorous uncertainty quantification in fuel performance and phase diagram modeling to better constrain predictions from compositional data.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Tuning Surface Adhesion Using Grayscale Electron-beam Lithography

Surface texturing of manufactured products tailors their properties, such as friction, adhesion, biocompatibility, or fluid interactions. However, advancements in this area are largely the result of trial-and-effort testing and generally lack a science-guided framework for determining the surface topography that will optimize performance. The present investigation explores grayscale electron-beam lithography as a means to create multiscale surface patterns to control surface performance. Here, we created and characterized a set of surface textures on a silicon wafer; the textures were superpositions of sine waves of varying wavelengths and amplitudes. First, the multiscale topography of the patterned surface was characterized, using profilometry and atomic force microscopy, to understand its fidelity to the designed-in pattern. The results of this analysis demonstrated how grayscale lithography accurately controlled the lateral size of features but was less precise on the vertical height of the surface, and also introduced inherent roughness below the scale of patterning. Second, a micromechanical tester was used to characterize the adhesion of the surfaces with large-scale polished silicon spheres. The results showed that adhesion could be tailored, with significant contribution from all of the designed-in length scales of topography. The strength of adhesion did not correlate with conventional roughness parameters but could be accurately modeled using simple numerical integration. Taken together, this investigation demonstrates the promise and challenges of grayscale e-beam lithography with multiscale patterns as a method for the tailoring of surface performance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

How Well Does the DOE Global Storm Resolving Model Simulate Clouds and Precipitation Over the Amazon?

This study assesses a 40-day 3.25-km global simulation of the Simple Cloud-Resolving E3SM Model (SCREAMv0) using high-resolution ground-based observations from the Atmospheric Radiation Measurement (ARM) Green Ocean Amazon (GoAmazon) field campaign. SCREAMv0 reasonably captures the diurnal timing of boundary layer clouds yet underestimates the boundary layer cloud fraction and mid-level congestus. SCREAMv0 well replicates the precipitation diurnal cycle, however it exhibits biases in the precipitation cluster size distribution compared to scanning radar observations. Specifically, SCREAMv0 overproduces clusters smaller than 128 km, and does not form enough large clusters. Such biases suggest an inhibition of convective upscale growth, preventing isolated deep convective clusters from evolving into larger mesoscale systems. This model bias is partially attributed to the misrepresentation of land-atmosphere coupling. This study highlights the potential use of high-resolution ground-based observations to diagnose convective processes in global storm resolving model simulations, identify key model deficiencies, and guide future process-oriented model sensitivity tests and detailed analyses.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Design of a Continuous Pellet Fueling System for Wendelstein 7-X

A continuous pellet fueling system (CPFS) is currently being designed at the Oak Ridge National Laboratory (ORNL) for the long pulse operation of the Wendelstein 7-X (W7-X) stellarator. The purpose of the CPFS is to provide deep continuous fueling for feedback-controlled high-density operation and mitigation of predicted hollow density profiles. As described here, the system will provide the capability to inject cylindrical pellets of solid hydrogen or deuterium into the plasma core, with flexibility to vary the pellet size, velocity, and injection frequency. Pellets are nominally of 3 mm in diameter and have a length between 1 and 4 mm. The heart of the CPFS is a vertically oriented, twin-screw extruder, cooled by three Gifford-McMahon cryocoolers in parallel, designed to form a continuous filament of hydrogen or deuterium. The filament width, which determines the pellet length, can be adjusted by means of a variable nozzle driven by a linear actuator at the base of the extruder. Coupled to the nozzle is a solenoid-operated gas gun and cutter assembly. A pneumatic propellant valve pulses a burst of ~60 bar helium to accelerate the cut pellet into W7-X. Three gaps in the guide tubes provide pumping locations to remove the helium propellant before it reaches the plasma. The maximum velocity of the pellet is limited by its ability to survive navigating the guide tube trajectory intact. A microwave cavity located within the guide tube provides the capability to measure the pellet size and velocity. The mechanical and thermal designs of the W7-X extruder, adjustable nozzle, and gun and cutter assembly design are described. A guide tube design and experimental pellet survivability test results are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Sierra/SolidMechanics 4.56 Capabilities In Development

This user's guide documents capabilities in Sierra/SolidMechanics which remain "in-development" and thus are not tested and hardened to the standards of capabilities listed in Sierra/SM 4.56 User's Guide. Capabilities documented herein are available in Sierra/SM for experimental use only until their official release. These capabilities include, but are not limited to, novel discretization approaches such as peridynamics and the reproducing kernel particle method (RKPM), numerical fracture and failure modeling aids such as the extended finite element method (XFEM) and J-integral, explicit time step control techniques, dynamic mesh rebalancing, as well as a variety of new material models and finite element formulations.

97 MATHEMATICS AND COMPUTING↗