Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “technology acceptance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Brief state-of-the-art review on optical communications for the NASA ISES workshop

The current state of the art of optical communications is briefly reviewed. This review covers NASA programs, DOD and other government agency programs, commercial aerospace programs, and foreign programs. Included is a brief summary of a recent NASA workshop on optical communications. The basic conclusions from all the program reviews is that optical communications is a technology ready to be accepted but needed to be demonstrated. Probably the most advanced and sophisticated optical communications system is the Laser Intersatellite Transmission Experiment (LITE) system developed for flight on the Advanced Communications Technology Satellite (ACTS). Optical communications technology is available for the applications of data communications at data rates in the under 300 MBits/sec for nearly all applications under 2 times GEO distances. Applications for low-earth orbiter (LEO) to ground will allow data rates in the multi-GBits/sec range. Higher data rates are limited by currently available laser power. Phased array lasers offer technology which should eliminate this problem. The major problem of cloud coverage can probably be eliminated by look ahead pointing, multiple ground stations, and knowledge of weather conditions to control the pointing. Most certainly, optical communications offer a new spectral region to relieve the RF bands and very high data communications rates that will be required in less than 10 years to solve the communications problems on Earth.

Hendricks, Herbert D.↗
NASA NTRS1984

What Pilots like (and Don't Like) About the New Cockpit Technology

Pilot's perceptions of the new cockpit technology in the B-767 are discussed. Although the data reported were taken from the introductory experience of the B-767, it is felt that similar, if not identical, results would be obtained with any other new cockpit technology aircraft, i.e., the A310. The following conclusions were drawn from the information collected thus far: A large majority of the pilots enjoy flying the B-767 more than the older airplanes. The pilots accept the new cockpit technology, and they choose to use it because they find it useful. The pilots are aware of the possible loss of flying skill with the presence of automation, and they hand fly (usually with flight director) to prevent this loss. There is no evidence of loss of skills from the data collected. The primary points of confusion or surprise were autothrottle/autopilot interactions; the autopilot during the wrong way or not capturing the course; and achieving desired results with the Flight Management System/Control Display Unit (FMS/CDU). The pilots felt training for the FMS/CDU could be improved, and they especially wanted more hands on experience.

Curry, R. E.↗
DOE OSTI2024

Geological Thermal Energy Storage (GeoTES) Charged with Solar Thermal Technology Using Depleted Oil/Gas Reservoirs and Carnot-Battery Technique Using Shallow Reservoirs: Preprint

Geological thermal energy storage (GeoTES) utilizes the underground reservoirs to storage and dispatch energy per given demand schedule over a time scale up to seasons of a year. The energy input can be of various sources/forms; in this paper, we investigate 1) the GeoTES technology with solar thermal hybridization and using depleted oil/gas reservoirs; 2) the GeoTES technology with heat pumps charged by excess renewable electricity and using low-temperature shallow reservoirs. For each GeoTES technology, we carry out the suitability analysis of candidate reservoirs, develop initial techno-economic models, and validate the model with selected case study. The paper provides an overview of our technical progress on the topics of concern and aims to promote a wider acceptance of the GeoTES technologies in the future energy market.

Carnot battery↗
NASA NTRS1993

Feasibility study of an orbiting laboratory for testing CSI technology

A concept for an orbiting laboratory for testing Controls-Structures Integration (CSI) technology is described. The CSI-Star concept reflects a lower cost, higher risk approach. The concept supports demonstration and validation testing for critical CSI technologies at a cost of $20M to $26M with a 1-year reliability of approximately 0.9. The Ball Aerospace QuickStar bus is the carrier for the CSI test article. QuickStar is launched as a secondary payload on the McDonnell Douglas Delta 2. The QuickStar/Delta 2 approach is flight proven. The CSI test article is a 20 foot, 1 Hz, truss beam which is deployed from the QuickStar bus. The test article is well instrumented for quality system identification. The laboratory provides three layers of active control consisting of global vibration suppression along the truss beam, vibration isolation between the beam and instrument platforms, and vibration compensation through the use of gimbaled platforms which point lasers relative to optical sensor targets. The configuration simulates the dynamics of multi-instrument science platforms such as those of the Earth Observation System (EOS) while maintaining strong ties to astrophysics missions such as the Optical Interferometer. Uplink/downlink services and a reprogrammable computer provide flexibility for long-term investigations by members of the CSI community (NASA, DoD, academia, and industry). CSI-Star fills the gap between short-term experiments, which have been conducted primarily on the Shuttle, and future science missions which require the technology. The on-orbit maturity of CSI technology must be established to obtain acceptance by project managers and to promote injection of the technology into future science missions.

Bicos, Andrew S.↗
NASA NTRS1985

A Study of the Utilization of Advanced Composites in Fuselage Structures of Commercial Aircraft

A study was conducted to define the technology and data needed to support the introduction of advanced composites in the future production of fuselage structure in large transport aircraft. Fuselage structures of six candidate airplanes were evaluated for the baseline component. The MD-100 was selected on the basis of its representation of 1990s fuselage structure, an available data base, its impact on the schedule and cost of the development program, and its availability and suitability for flight service evaluation. Acceptance criteria were defined, technology issues were identified, and a composite fuselage technology development plan, including full-scale tests, was identified. The plan was based on composite materials to be available in the mid to late 1980s. Program resources required to develop composite fuselage technology are estimated at a rough order of magnitude to be 877 man-years exclusive of the bird strike and impact dynamic test components. A conceptual composite fuselage was designed, retaining the basic MD-100 structural arrangement for doors, windows, wing, wheel wells, cockpit enclosure, major bulkheads, etc., resulting in a 32 percent weight savings.

Watts, D. J.↗
NASA NTRS2002

NASA Technology Investments in Electric Propulsion: New Directions in the New Millennium

The last decade was a period of unprecedented acceptance of NASA developed electric propulsion by the user community. The benefits of high performance electric propulsion systems are now widely recognized, and new technologies have been accepted across the commonly. NASA clearly recognizes the need for new, high performance, electric propulsion technologies for future solar system missions and is sponsoring aggressive efforts in this area. These efforts are mainly conducted under the Office of Aerospace Technology. Plans over the next six years include the development of next generation ion thrusters for end of decade missions. Additional efforts are planned for the development of very high power thrusters, including magnetoplasmadynamic, pulsed inductive, and VASIMR, and clusters of Hall thrusters. In addition to the in-house technology efforts, NASA continues to work closely with both supplier and user communities to maximize the acceptance of new technology in a timely and cost-effective manner. This paper provides an overview of NASA's activities in the area of electric propulsion with an emphasis on future program directions.

Sankovic, John M.↗
NASA NTRS1995

Development of advanced structural analysis methodologies for predicting widespread fatigue damage in aircraft structures

NASA is developing a 'tool box' that includes a number of advanced structural analysis computer codes which, taken together, represent the comprehensive fracture mechanics capability required to predict the onset of widespread fatigue damage. These structural analysis tools have complementary and specialized capabilities ranging from a finite-element-based stress-analysis code for two- and three-dimensional built-up structures with cracks to a fatigue and fracture analysis code that uses stress-intensity factors and material-property data found in 'look-up' tables or from equations. NASA is conducting critical experiments necessary to verify the predictive capabilities of the codes, and these tests represent a first step in the technology-validation and industry-acceptance processes. NASA has established cooperative programs with aircraft manufacturers to facilitate the comprehensive transfer of this technology by making these advanced structural analysis codes available to industry.

Harris, Charles E.↗
NASA NTRS1990

The need for a hypersonic demonstrator

The requirement for research aircraft and demonstrator vehicles has been seriously challenged by tight budgets and erroneous impressions that aeronautical technology has matured to a point where the value added by flight research and/or demonstration is not sufficient to offset the costs. While this issue may be debatable with respect to subsonic/transonic speeds, such is not the case for high-speed (supersonic and hypersonic) operation. The aerodynamic performance, weight/payload fractions, and thermodynamic problems are such that small margins of error can be tantamount to the vehicle being unable to reach its design point or so inefficient as to render it useless. This paper addresses some of the critical design considerations and operational constraints which make it mandatory to carry out flight research and develop a demonstrator vehicle in order that the risks be reduced to an acceptable level to assure technology readiness for viable hypersonic flight.

Ayers, T. G.↗
DOE OSTI2023

Development and testing of residential micro-CHP powered by opposed piston engine (CRADA Final Report)

A micro–combined heat and power (mCHP) prototype powered by innovative opposed piston engine technology was developed to simultaneously provide electricity and heat to residential or light commercial buildings. The mCHP prototype targeted at residential applications includes an opposed-piston four-stroke (OP4S) engine, generator, rectifier, inverter, battery energy storage system, 52 gal water tank, and application accessories for hot water supply and space heating. The OP4S engine can use renewable or regular natural gas, as well as hydrogen, to generate mechanical power and waste heat in form of hot coolant and exhaust gas simultaneously. The waste heat is recovered and stored in the water tank and can be used as a regular hot water supply and/or for space heating application. The tests show that the mCHP prototype enabled power outputs in the range of 3.2 –7.4 kW with up to 26.4% of AC electricity efficiency and up to 93.1% of the overall mCHP efficiency under stoichiometric combustion modes λ=~1.0. The mCHP was also run under lean combustion mode conditions at λ=~1.3. The lean mode operation enables more than 30% improvement in electrical energy efficiency. The maximum AC efficiency of the lean combustion mode attained was 35.2%, with the engine efficiency is approaching 40%. The exceptional electrical efficiency breaks the typical upper boundary of 30% for ICE-based mCHP. The engine exhaust temperatures in the lean modes are substantially less than in the stoichiometric modes. Moreover, the lean cases achieve high overall mCHP efficiencies: the overall mCHP efficiencies are all greater than 93%. Considering the mCHP prototype can achieve low-cost, flexible matching of thermal and electrical loads through reducing the complexity of distribution and installation, and high efficiency the novel technology will promote mCHP acceptance in the US residential and light commercial markets.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Technical and Community Foundations for High-Integrity CDR MRV Standards (Final Report)

The goal of this project (hereafter referred to as the “umbrella project”) was to establish cross-cutting technical foundations for carbon dioxide removal (CDR) accounting decisions. These cross-cutting and science driven technical foundations are necessary to increase trust in standards-setting and protocol development. According to key stakeholders in the industry, establishment of trusted standards is necessary to unlock and catalyze investment in the CDR industry as well as commercialization and deployment of verified, accepted high quality CDR technologies. Additionally, our umbrella project served as the lead coordinator of the cohort of three additional CDR pathway-focused projects funded under this award. In this role, we brought together the project teams to share insights, industry feedback, and approaches to CDR accounting standards development.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Understanding the use intention and influencing factors of telerehabilitation in people with rehabilitation needs: a cross-sectional survey

Objective This study aimed to investigate the use intention and influencing factors of telerehabilitation in people with rehabilitation needs. Methods This cross-sectional survey recruited a total of 183 participants with rehabilitation needs from May 2022 to December 2022. Sociodemographic and medical data were collected by a structured questionnaire. The factors influencing the use intention of telerehabilitation were measured by the extended Unified Theory of Acceptance and Use of Technology (UTAUT) model. Multiple hierarchical regression analyses were performed. Results A total of 150 valid questionnaires were included for analysis. The results indicated that the use intention of telerehabilitation was overall high in people with rehabilitation needs. Health condition ( β = −0.21, p = 0.03), performance expectancy ( β = 0.21, p = 0.01), facilitating conditions ( β = 0.25, p = 0.03), perceived trust ( β = 0.25, p < 0.01), and self-efficacy ( β = 0.19, p = 0.04) were significant factors influencing the use intention of telerehabilitation. Conclusion Overall, the use intention of telerehabilitation is high in individuals with rehabilitation needs. Health conditions, performance expectancy, facilitating conditions, perceived trust, and self-efficacy are important factors influencing the use intention of telerehabilitation in individuals with rehabilitation needs.

Wang, Mao-Yuan↗
NASA NTRS1972

Contamination avoidance devices for poppet type shutoff valves

The technology required to provide acceptable contamination damage avoidance characteristics for poppet type shutoff valves is discussed. Evaluation of the contamination avoidance characteristics of the basic 1T32095 propellant shutoff valve, the cycle life performance of these valves in an uncontaminated environment, and the effectiveness of various auxiliary contamination avoidance devices when used in conjunction with these poppet type valves are included. In addition, a secondary objective is to evaluate two methods of monitoring the performance of the test valves during actual operations using acoustical monitoring instrumentation.

Endicott, D. L.↗
NASA NTRS1973

Data bus system development program

Two data bus systems were designed fabricated, Data Bus System I and Data Bus System II. The technical features of the delivered hardware include the following: (1) 5 MHz selfclocking data bus; (2) bidirectional communications utilizing Manchester Code at data rates in excess of 20,000 words per second; (3) utilization of MSI COS/MOS technology (4) probability of accepting an erroneous data bit less than 1 in 10 to the 25th power (5) low power consumption (50 to 1 reduction in quiescent current over P/MOS) (6) compatibility with projected high density packaging. Three distinct types of data bus remote terminals were developed: the subsystem interface unit, the combination of an electronic interface unit and a standard interface unit-serial, and an SIU/Preprocessor.

Harrison, J. S. J.↗
NASA NTRS1980

An evaluation of NASA's program for improving aircraft fuel efficiency

The report provides commentary and recommendations where appropriate on each of the major elements of the program. Key findings of the committee included a recommendation that closer ties be established between NASA and the FAA to expedite the use and acceptance of the new technology. The committee also cited the potential for fuel savings through an imporved air traffic control system and recommended that the management of NASA and the FAA discuss ways and means to work together to exploit more effectively the capabilities and responsibilities of each to develop air traffic control.

Source record↗
NASA NTRS1987

A perspective on 15 years of proof-of-concept aircraft development and flight research at Ames-Moffett by the Rotorcraft and Powered-Lift Flight Projects Division, 1970-1985

A proof-of-concept (POC) aircraft is defined and the concept of interest described for each of the six aircraft developed by the Ames-Moffet Rotorcraft and Powered-Lift Flight Projects Division from 1970 through 1985; namely, the OV-10, the C-8A Augmentor Wing, the Quiet Short-Haul Research Aircraft (QSRA), the XV-15 Tilt Rotor Research Aircraft (TRRA), the Rotor Systems Research Aircraft (RSRA)-compound, and the yet-to-fly RSRA/X-Wing Aircraft. The program/project chronology and most noteworthy features of the concepts are reviewed. The paper discusses the significance of each concept and the project demonstrating it; it briefly looks at what concepts are on the horizon as potential POC research aircraft and emphasizes that no significant advanced concept in aviation technology has ever been accepted by civilian or military users without first completing a demonstration through flight testing.

Few, David D.↗
NASA NTRS1987

Robotic mobile servicing platform for space station

The semi-autonomous inspection and servicing of the Space Station's major thermal, electrical, mechanical subsystems are critical needs for the safe and reliable operation of the station. A conceptual design is presented of a self-intelligent, small and highly mobile robotic platform. Equipped with suitable inspection sensors (cameras, ammonia detectors, etc.), this system's primary mission is to perform routine, autonomous inspection of the Station's primary subsystems. Typical tasks include detection of leaks from thermal fluid or refueling lines, as well as detection of micro-meteroid damage to the primary structure. Equipped with stereo cameras and a dexterous manipulator, simple teleoperator repairs and small On-orbit Replacement Unit (ORU) changeout can also be accomplished. More difficult robotic repairs would be left to the larger, more sophisticated Mobile Remote Manipulator System (MRMS). An ancillary function is to ferry crew members and equipment around the station. The primary design objectives were to provide a flexible, but uncomplicated robotic platform, one which caused minimal impact to the design of the Station's primary structure but could accept more advanced telerobotic technology as it evolves.

Lowenthal, S. H.↗
NASA NTRS1992

Directions for future Earth-to-orbit vehicles

NASA is currently assessing several programmatic possibilities. The desire is to maintain the current capability for transportation to orbit provided by the Space Shuttle and the existing fleet of commercial vehicles, develop the Space Station Freedom, and initiate a new program of exploration of the Moon and Mars, called the Space Exploration Initiative (SEI). At the same time, the NASA budget is likely to be held to current levels. Cost estimates indicate that it will not be possible to satisfy all the goals without cost reductions. One of the concepts being considered for cost reduction is to replace the Space Shuttle and existing commercial vehicles with a new set of vehicles called the National Launch System (NLS). Several concepts have been studied, but none of the concepts studied to date provides the desired combination of cost/flight reduction, acceptable development cost, and technology readiness. An additional goal is to provide a path to grow the NLS capability into a heavy-lift capability for SEI missions.

Martin, James A.↗
NASA NTRS1993

SPDE/SPRE final summary report

Mechanical Technology Incorporated (MTI) performed acceptance testing on the Space Power Research Engine (SPRE), which demonstrated satisfactory operation and sufficient reliability for delivery to NASA Lewis Research Center. The unit produced 13.5 kW PV power with an efficiency of 22 percent versus design goals of 28.8 kW PV power and efficiency of 28 percent. Maximum electric power was only 8 kWe due to lower alternator efficiency. One of the major shortcomings of the SPRE was linear alternator efficiency, which was only 70 percent compared to a design value of 90 percent. It was determined from static tests that the major cause for the efficiency shortfall was the location of the magnetic structure surrounding the linear alternator. Testing of an alternator configuration without a surrounding magnetic structure on a linear dynamometer confirmed earlier static test results. Linear alternator efficiency improved from 70 percent to over 90 percent. Testing of the MTI SPRE was also performed with hydrodynamic bearings and achieved full-stroke, stable operation. This testing indicated that hydrodynamic bearings may be useful in free piston Stirling engines. An important factor in achieving stable operation at design stroke was isolating a portion of the bearing length from the engine pressure variations. In addition, the heat pipe heater head design indicates that integration of a Stirling engine with a heat source can be performed via heat pipes. This design provides a baseline against which alternative designs can be measured.

Dochat, George↗