Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “supercooled liquid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Comparison of In-Situ, Model and Ground Based In-Flight Icing Severity

As an aircraft flies through supercooled liquid water, the liquid freezes instantaneously to the airframe thus altering its lift, drag, and weight characteristics. In-flight icing is a contributing factor to many aviation accidents, and the reliable detection of this hazard is a fundamental concern to aviation safety. The scientific community has recently developed products to provide in-flight icing warnings. NASA's Icing Remote Sensing System (NIRSS) deploys a vertically--pointing Ka--band radar, a laser ceilometer, and a profiling multi-channel microwave radiometer for the diagnosis of terminal area in-flight icing hazards with high spatial and temporal resolution. NCAR s Current Icing Product (CIP) combines several meteorological inputs to produce a gridded, three-dimensional depiction of icing severity on an hourly basis. Pilot reports are the best and only source of information on in-situ icing conditions encountered by an aircraft. The goal of this analysis was to ascertain how the testbed NIRSS icing severity product and the operational CIP severity product compare to pilot reports of icing severity, and how NIRSS and CIP compare to each other. This study revealed that the icing severity product from the ground-based NASA testbed system compared very favorably with the operational model-based product and pilot reported in-situ icing.

Johnston, Christopher J.↗
NASA NTRS2014

NASA Glenn Propulsion Systems Lab: 2012 Inaugural Ice Crystal Cloud Calibration Procedure and Results

The inaugural calibration of the ice crystal and supercooled liquid water clouds generated in NASA Glenn's engine altitude test facility, the Propulsion Systems Lab (PSL) is reported herein. This calibration was in support of the inaugural engine ice crystal validation test. During the Fall of 2012 calibration effort, cloud uniformity was documented via an icing grid, laser sheet and cloud tomography. Water content was measured via multi-wire and robust probes, and particle sizes were measured with a Cloud Droplet Probe and Cloud Imaging Probe. The environmental conditions ranged from 5,000 to 35,000 ft, Mach 0.15 to 0.55, temperature from +50 to -35 F and relative humidities from less than 1 percent to 75 percent in the plenum.

ice clouds↗
NASA NTRS2011

Comparison of In-Situ, Model and Ground Based In-Flight Icing Severity

Currently there are two systems that are being developed for the detection of in-flight icing: NASA Icing Remote Sensing System (NIRSS) and current Icing Product (CIP). In-flight icing (IFI) is a significant hazard for the aviation industry. IFI occurs when supercooled liquid water (SLW) comes in contact with, and freezes to, the leading surfaces of an aircraft. Significantly alters aircraft aerodynamic properties: increases the amount of drag on an aircraft and reduces the lift. The objective of this study is to examine how the testbed NIRSS icing severity product and the operational CIP severity product compare to PIREPs of icing severity, and how the NIRSS and CIP compare to each other.

Serke, David J.↗
NASA NTRS2016

Using 3-D Numerical Weather Data in Piloted Simulations

This report describes the process of acquiring and using 3-D numerical model weather data sets in NASA Langley's Research Flight Deck (RFD). A set of software tools implement the process and can be used for other purposes as well. Given time and location information of a weather phenomenon of interest, the user can download associated numerical weather model data. These data are created by the National Oceanic and Atmospheric Administration (NOAA) High Resolution Rapid Refresh (HRRR) model, and are then processed using a set of Mathworks' Matlab(TradeMark) scripts to create the usable 3-D weather data sets. Each data set includes radar re ectivity, water vapor, component winds, temperature, supercooled liquid water, turbulence, pressure, altitude, land elevation, relative humidity, and water phases. An open-source data processing program, wgrib2, is available from NOAA online, and is used along with Matlab scripts. These scripts are described with sucient detail to make future modi cations. These software tools have been used to generate 3-D weather data for various RFD experiments.

Daniels, Taumi S.↗
NASA NTRS2016

Update on the NASA Glenn PSL Ice Crystal Cloud Characterization (2016)

NASA Glenn's Propulsion Systems Laboratory (PSL) is an altitude engine research test facility capable of producing ice-crystal and supercooled liquid clouds. The cloud characterization parameter space is fairly large and complex, but the phase of the cloud seems primarily governed by wet bulb temperature. The presentation will discuss some of the issues uncovered through four cloud characterization efforts to date, as well as some of instrumentation that has been used to characterize cloud parameters including cloud uniformity, bulk total water content, median volumetric diameter and max-diameter, percent freeze-out, relative humidity, and an update on the NASA Glenn PSL Ice Crystal Cloud Characterization (2016).

Calibration↗
NASA NTRS2019

Evidence of Strong Contributions from Mixed-Phase Clouds to Arctic Climate Change

Underestimation of the proportion of supercooled liquid in mixed‐phase clouds in climate models has called into question its impact on Arctic climate change. We show that correcting for this bias in the CESM model can either enhance or reduce Arctic amplification depending on the microphysical characteristics of the clouds as a corollary to the cloud phase feedback. Replacement of ice with liquid in the cloud phase feedback results in more downward longwave radiation, which is effectively trapped as heat at the surface in the Arctic due to its unique stable stratification conditions, and this ultimately leads to a more positive lapse rate feedback. The larger the ice particles are to begin with, the stronger Arctic amplification becomes due to the lower precipitation efficiency of liquid droplets compared to ice crystals. Our results emphasize the importance of realistic representations of microphysical processes in mixed‐phase clouds, particularly in the Arctic.

Arctic↗
NASA NTRS2019

Microphysical Retrievals from Simultaneous Measurements by Airborne and Ground Radars during OLYMPEX

The OLYMPEX field campaign took place over the Olympic Peninsula of Washington during winter 2015-2016. During the intensive observing period, several aircraft flights obtained multi-frequency airborne radar measurements at X-, Ku-, Ka, and W-band from radars aboard the ER-2 and DC-8 aircraft. In addition, ground radars at S- and X-band performed RHI scans under the aircraft ground tracks. These coincident datasets provide a wealth of complementary information about the hydrometeor particle sizes, shapes, and orientations.In order to synthesize these measurements and test the robustness of scattering models, an optimal estimation retrieval based upon a Hitschfeld-Bordan profiling algorithm has been developed. This algorithm retrieves profiles of the particle size distribution parameters Nw and Dm, and, in the ice phase, relative proportions of aggregate, pristine, and rimed particles, using scattering models with different size-density and size-aspect ratio relationships. Under this formulation, only the pristine particles are horizontally aligned and capable of producing non-zero ZDR and KDP.From the nadir-looking airborne multifrequency radars, we find that aggregates may be readily distinguished from rimed and pristine particles owing to their uniqueness in triple-frequency space. However, rimed and pristine particles occupy a similar region in this space and thus polarimetric measurements greatly enhance their identification in our retrieval framework. With these capabilities we will present analyses of three-dimensional hydrometeor mapping obtained during various OLYMPEX cases. Some features retrieved in these cases include a layer of enhanced aggregation about 2km above the melting layer, hypothesized to be maintained by orographic uplift. This layer is often situated above a layer of denser, aligned particles. Regions of riming and supercooled liquid water beneath generating cells are also identified by our retrieval algorithm. Comparisons to in-situ observations and evaluation of scattering models will be presented.

Munchak, S. Joseph↗
NASA NTRSDate not supplied

A Study of Ice-Crystal Icing Erosion Using the NASA Icing Research Tunnel and Propulsion Systems Laboratory

In ice-crystal icing, ice erosion can occur simultaneously with ice accretion. This paper presents a proof-of-concept experimental study that attempts to isolate and quantify ice erosion. The experiments took place at the NASA Icing Research Tunnel and Propulsion Systems Laboratory in 2017 and 2018. The test procedure involved first generating an ice accretion on various NACA 0012 airfoil models using a supercooled liquid water or mixed-phase icing cloud and, subsequently, exposing that ice accretion to an ice crystal cloud. The resulting ice mass decay rates were analyzed in terms of an erosion term, defined as the ratio of the eroded mass flux to impinging mass flux. The erosion term generally increased with airspeed with a value of 1.8% at air velocities of 270 knots and increasing to just over 6% at 360 knots. A preliminary correlation for ice erosion is developed for use in ice accretion models subject to the conditions tested. The study revealed several challenges, both experimental and analytical, including spray bar nozzle freeze-out as well as measurement of the cloud melt ratio to ensure freeze-out.

Icing↗
NASA NTRS2022

Southern Ocean Solar Reflection Biases in Cmip6 Models Linked to Cloud Phase and Vertical Structure Representations

Over the Southern Ocean (SO, 40˚S-70˚S), climate models have consistently underestimated solar reflection. Here we evaluate the relationship between cloud profiles, cloud phase and radiation over the SO in Coupled Model Intercomparison Project Phase 6 (CMIP6) models against Clouds and the Earth's Radiant Energy System (CERES) and Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO). We find that the lack of solar reflection is slightly improved in CMIP6 models compared to CMIP5’s, attributable to a better representation of cloud fraction and phase. We show that clouds have a different vertical structure and radiative effect south and north of where the 0˚C isotherm meets the surface (~55˚S). Although the models capture the greater vertical extent of clouds south of 55˚S, they fail to reproduce the observed increase in solar reflection, which we pinpoint to cloud phase biases. Increasing CMIP6 supercooled liquid cloud opacity should help reduce their persistent SW biases.

Southern Ocean↗
NASA NTRS2023

Electrification Within Wintertime Stratiform Regions Sampled During the 2020/2022 NASA IMPACTS Field Campaign

Two nor'easter events—sampled during the NASA Investigation of Microphysics and Precipitation for Atlantic Coast-Threatening Snowstorms (IMPACTS) field campaign—were examined to characterize the microphysics in relation to the underlying electrification processes within wintertime stratiform regions. A theoretical model was developed to determine whether accretion or diffusion growth regimes were preferential during periods of greatest electrification. Model simulation with electrification parameterization was used to provide supplemental context to the physical processes of in-cloud microphysics and electrification. The strongest electric fields (i.e., ∼80 V m −1 at 20 km) during the 2020 NASA IMPACTS deployment was associated with large non-rimed ice crystals colliding with each other. During the 29–30 January 2022 science flight, the NASA P-3 microphysical probe data demonstrated that non-inductive charging was possible off the coastline of Cape Cod, Massachusetts. Later in the science flight, when the NASA P-3 and ER-2 were coordinating with each other, measured electric fields consistently were less than 8 V m −1 and electrification was subdued owing to reduced concentrations of graupel and large ice hydrometeors. Altogether, the in-situ observations provide evidence for the non-riming collisional charging mechanism and demonstrates that graupel and supercooled liquid water may not be necessary for weak electrification within wintertime stratiform regions. Model output from simulation of both events suggested that the main synoptic snowbands were associated with elevated hydrometeor snow charge density and electric fields.

snowfall↗
NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap joint method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a comprehensive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗
NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap join method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a compressive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗
NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Ice Crystal Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for the development of icing physics models and simulation validation. This paper presents the analysis of the ice crystal icing data subset from tests conducted in 2022 at the NASA Icing Research Tunnel that studied both supercooled liquid and ice-crystal icing. The test article that was utilized replicated 3D geometrical features of an inter-compressor duct and strut region of a turbofan engine. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a weighing scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized icing conditions. To that end, ice crystal cloud characterization tests were conducted that provided cloud property values at the test section. The ice crystal accretion tests investigated how different test condition parameters impacted ice accretion size, location, and characteristics (such as physical attributes). A key finding was that a sufficiently high surface heat flux at the leading edge can provide a continuous supply of liquid melt to critical accretion zones downstream, resulting in elevated ice mass accretions. Another key finding was that warmer heater settings in critical accretion zones can suppress ice accretion. These findings are consistent with icing behavior observed in full-scale engine icing tests conducted previously at the NASA Glenn Research Center. Test runs investigating the contribution of liquid melt generated at the leading edge found that the melt can be transported downstream to critical accretion regions in two forms, via runback and splash. The form of melt supplied downstream affected accretion behavior and features. Sharkteeth-shaped ice accretions were generated at certain test conditions, a physical attribute that has been observed in full-scale engine icing tests. The ice accretion data will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost‑effective way.

ice crystal icing↗
NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Ice Crystal Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for the development of icing physics models and simulation validation. This paper presents the analysis of the ice crystal icing data subset from tests conducted in 2022 at the NASA Icing Research Tunnel that studied both supercooled liquid and ice-crystal icing. The test article that was utilized replicated 3D geometrical features of an inter-compressor duct and strut region of a turbofan engine. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a weighing scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized icing conditions. To that end, ice crystal cloud characterization tests were conducted that provided cloud property values at the test section. The ice crystal accretion tests investigated how different test condition parameters impacted ice accretion size, location, and characteristics (such as physical attributes). A key finding was that a sufficiently high surface heat flux at the leading edge can provide a continuous supply of liquid melt to critical accretion zones downstream, resulting in elevated ice mass accretions. Another key finding was that warmer heater settings in critical accretion zones can suppress ice accretion. These findings are consistent with icing behavior observed in full-scale engine icing tests conducted previously at the NASA Glenn Research Center. Test runs investigating the contribution of liquid melt generated at the leading edge found that the melt can be transported downstream to critical accretion regions in two forms, via runback and splash. The form of melt supplied downstream affected accretion behavior and features. Sharkteeth-shaped ice accretions were generated at certain test conditions, a physical attribute that has been observed in full-scale engine icing tests. The ice accretion data will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost‑effective way.

ice crystal icing↗
NASA NTRS2022

166 GHZ Ice Scattering Signal in Snowfall Events Over Ocean

Snowfall retrieval algorithms for spaceborne passive microwave (PMW) sensors have been developed and refined in recent years, but many complicating issues still affect their accuracy and reliability. Previous work showed that the Global Precipitation Measurement (GPM) mission Goddard PROFiling (GPROF) algorithm snowfall retrieval performance strongly depends on the snowfall type. In particular, PMW-based detection of shallow cumuliform snowfall (SCS), which accounts for 36%-70% of global snowfall frequency, can be very challenging. The snowfall scattering signal can be contaminated by the background surface or supercooled cloud liquid water emission. A scattering index (SI) approach that exploits the GPM Microwave Imager (GMI) dual-polarization 166 GHz channels is developed to analyze its behavior in presence of SCS over ocean. Case studies show that, compared to the SI at 89 GHz, it can isolate the SCS snowfall scattering signal in extremely dry conditions. Some issues are still observed in presence of supercooled liquid water.

Lisa Milani↗
NASA NTRS1951

Analysis of Meteorological Data Obtained During Flight in a Supercooled Stratiform Cloud of High Liquid-Water Content

Flight icing-rate data obtained in a dense and. abnormally deep supercooled stratiform cloud system indicated the existence of liquid-water contents generally exceeding values in amount and extent previously reported over the midwestern sections of the United States. Additional information obtained during descent through a part of the cloud system indicated liquid-water contents that significantly exceeded theoretical values, especially near the middle of the cloud layer.. The growth of cloud droplets to sizes that resulted in sedimentation from the upper portions of the cloud is considered to be a possible cause of the high water contents near the center of the cloud layer. Flight measurements of the vertical temperature distribution in the cloud layer indicated a rate of change of temperature with altitude exceeding that of the moist adiabatic lapse rate. This excessive rate of change is considered to have contributed to the severity of the condition.

Perkins, Porter J.↗
NASA NTRS2024

Observational Constraint on A Feedback From Supercooled Clouds Reduces Projected Warming Uncertainty

The increase of carbon-dioxide-doubling-induced warming (climate sensitivity) in the latest climate models is primarily attributed to a larger extratropical cloud feedback. This is thought to be partly driven by a greater ratio of supercooled liquid-phase clouds to all clouds, termed liquid phase ratio. We use an instrument simulator approach to show that this ratio has increased in the latest climate models and is overestimated rather than underestimated as previously thought. In our analysis of multiple models, a greater ratio corresponds to stronger negative cloud feedback, in contradiction with single-model-based studies. We trace this unexpected result to a cloud feedback involving a shift from supercooled to warm clouds as climate warms, which corresponds to greater cloud amount and optical depth and weakens the extratropical cloud feedback. Better constraining this ratio in climate models – and thus this supercooled cloud feedback – impacts their climate sensitivities by up to 1 ˚C and reduces inter-model spread.

Climate and Earth system modelling↗