Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Strain-tunable microwave-resonance technique for quantum materials

By integrating a dielectric microwave resonator with a piezoelectric-based strain device, we develop an in situ strain-tunable microwave spectroscopy technique that enables contactless measurements of material properties under strain. To demonstrate the capability of this device, we measure the strain-dependent microwave surface impedance of the representative iron-based superconductor Ba⁢Fe 2 (As 1−𝑥 ⁢P 𝑥 ) 2 at the slightly overdoped composition. We successfully control and observe the suppression of superconductivity under both compressive and tensile anisotropic lattice distortions along the tetragonal [110] T direction, as manifested by changes in the quality factor and resonance frequency shifts of microwave resonance. Furthermore, strain-induced changes in microwave surface resistivity, an extension of conventional DC-limit transport elastoresistivity to the microwave regime, provide information on electronic anisotropy equivalent to that of DC elastoresistivity, while offering a contactless alternative. Furthermore, our strain-tunable cavity therefore serves as a powerful, contactless probe of fundamental material properties under strain and may also potentially facilitate the design of hybrid quantum systems with strain-engineered quantum degrees of freedom.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Machine learning for deep elastic strain engineering of semiconductor electronic band structure and effective mass

Abstract The controlled introduction of elastic strains is an appealing strategy for modulating the physical properties of semiconductor materials. With the recent discovery of large elastic deformation in nanoscale specimens as diverse as silicon and diamond, employing this strategy to improve device performance necessitates first-principles computations of the fundamental electronic band structure and target figures-of-merit, through the design of an optimal straining pathway. Such simulations, however, call for approaches that combine deep learning algorithms and physics of deformation with band structure calculations to custom-design electronic and optical properties. Motivated by this challenge, we present here details of a machine learning framework involving convolutional neural networks to represent the topology and curvature of band structures in k -space. These calculations enable us to identify ways in which the physical properties can be altered through “deep” elastic strain engineering up to a large fraction of the ideal strain. Algorithms capable of active learning and informed by the underlying physics were presented here for predicting the bandgap and the band structure. By training a surrogate model with ab initio computational data, our method can identify the most efficient strain energy pathway to realize physical property changes. The power of this method is further demonstrated with results from the prediction of strain states that influence the effective electron mass. We illustrate the applications of the method with specific results for diamonds, although the general deep learning technique presented here is potentially useful for optimizing the physical properties of a wide variety of semiconductor materials.

Tsymbalov, Evgenii↗
DOE OSTI2024

Design by analysis rules for ASME Section III, Division 5, Class B components

The current rules for elevated temperature ASME Section III, Division 5, Class B components, other than piping, were basically adapted from the Design-by-Rule approach for Section VIII, Division 1 vessels. A goal of the proposed new rules is to explicitly account for the design life and cyclic service while recognizing the less-rigorous requirements commensurate with lesser safety consideration. Further goals are to maximize the use of modern computational technology, for example finite element analysis in conjunction with reference stress concepts, and to avoid the need for stress classification. This paper summarizes the work done to address these issues. A summary of the design-by-analysis for primary loads, strain limit evaluation, and creep-fatigue damage assessment is presented. The proposed design-by-analysis creep-fatigue damage calculation approach uses a new elastic follow-up-based Isochronous Stress Strain Curve stress relaxation procedure. A set of sample problems are selected to validate the proposed design-by-analysis rules for creep-fatigue damage assessment. The proposed Class B rules are evaluated against the Class A elastic design rules and the experimental data obtained from a family of a simplified model test-based key-feature test results. The proposed Class B creep-fatigue damage assessment methodology yields conservative design cycles estimates compared to the experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Geobacter sp. Strain IAE Dihaloeliminates 1,1,2-Trichloroethane and 1,2-Dichloroethane

We report that chlorinated ethanes, including 1,2-dichloroethane (1,2-DCA) and 1,1,2-trichloroethane (1,1,2-TCA), are widespread groundwater contaminants. Enrichment cultures XR DCA and XR TCA derived from river sediment dihaloeliminated 1,2-DCA to ethene and 1,1,2-TCA to vinyl chloride (VC), respectively. The XR TCA culture subsequently converted VC to ethene via hydrogenolysis. Microbial community profiling demonstrated the enrichment of Geobacter 16S rRNA gene sequences in both the XR DCA and XR TCA cultures, and Dehalococcoides mccartyi (Dhc) sequences were only detected in the ethene-producing XR TCA culture. The presence of a novel Geobacter population, designated as Geobacter sp. strain IAE, was identified by the 16S rRNA gene-targeted polymerase chain reaction and Sanger sequencing. Time-resolved population dynamics attributed the dihaloelimination activity to strain IAE, which attained the growth yields of 0.93 ± 0.06 x 10 7 and 1.18 ± 0.14 x 10 7 cells per μmol Cl -1 released with 1,2-DCA and 1,1,2-TCA as electron acceptors, respectively. In contrast, Dhc growth only occurred during VC-to-ethene hydrogenolysis. Our findings discover a Geobacter sp. strain capable of respiring multiple chlorinated ethanes and demonstrate the involvement of a broader diversity of organohalide-respiring bacteria in the detoxification of 1,2-DCA and 1,1,2-TCA.

1,1,2-trichloroethane↗
DOE OSTI2021

Direct Integration of Strained-Pt Catalysts into Proton-Exchange-Membrane Fuel Cells with Atomic Layer Deposition

The design and fabrication of lattice-strained platinum catalysts achieved by removing a soluble core from a platinum shell synthesized via atomic layer deposition, is reported. The remarkable catalytic performance for the oxygen reduction reaction (ORR), measured in both half-cell and full-cell configurations, is attributed to the observed lattice strain. By further optimizing the nanoparticle geometry and ionomer/carbon interactions, mass activity close to 0.8 A mg Pt -1 @0.9 V iR-free is achievable in the membrane electrode assembly. Nevertheless, active catalysts with high ORR activity do not necessarily lead to high performance in the high-current-density (HCD) region. More attention shall be directed toward HCD performance for enabling high-power-density hydrogen fuel cells.

25 ENERGY STORAGE↗
DOE OSTI2026

Leveraging a synthetic biology approach to enhance BCG-mediated expansion of Vγ9Vδ2 T cells

There is an urgent need to develop a more efficacious anti-tuberculosis vaccine as the current live-attenuated vaccine strain BCG fails to prevent pulmonary infection in adults. In this study, we leverage a synthetic biology approach to engineer BCG to produce more (E)-4-hydroxy-3-methyl-but-2-enyl pyrophosphate (HMBPP), an intermediate of bacterial—but not host—isoprenoid biosynthesis via the methylerythritol phosphate (MEP) pathway. HMBPP strongly activates and expands Vγ9Vδ2 T cells, which are unique to higher-order primates and protect against Mycobacterium tuberculosis infection. BCG has been engineered to produce specific ligands and antigens to some success; in contrast, our strategy exploits a self-nonself recognition mechanism in the host via HMBPP sensing, which has not been attempted before. To inform the design of our recombinant strains, we performed synteny analyses of >63 mycobacterial species and found that isoprenoid biosynthetic genes are not operonic across all the 356 surveyed genomes, but some genes are frequently found in pairs. Thus, we generated synthetic loci with the goal of specifically overproducing HMBPP and tested the ability of these engineered strains to induce human Vγ9Vδ2 expansion in an in vitro stimulation assay. We found that BCG expressing a synthetic MEP locus significantly enhanced Vγ9Vδ2 T cell expansion over the wild-type vaccine strain, and overexpression of the HMBPP synthase GcpE alone potently induced Vγ9Vδ2 T cell expansion with no downregulation of other pathway genes. Together these engineered strains present two successful strategies to accumulate HMBPP and overcome feedback inhibition of the MEP pathway.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Fuel performance evaluation of two high burnup PWR core designs during normal operation, control rod withdrawal, and control rod ejection scenarios

There is interest among utilities to extend the current, 18-month operating cycle to 24 months. Economically, this extension would require greater than 5 % enrichment and peak rod average discharge burnup levels above 62 GWd/MTU. A notable challenge of increasing enrichment is the resulting additional excess reactivity encountered during the early stages of fuel life. To accommodate, burnable absorbers beyond soluble boron are introduced into the fuel system. In high burnup fuels, the possibilities of cladding lift-off and fuel melting increase due, in part, to increased rod internal pressures and limited fuel thermal conductivity, respectively. This work collaboratively employs PARCS, RELAP5-3D, and BISON to compare the fuel performance of two high burnup fuel candidates with higher than 5 % enrichment. Here, the fuel performance parameters were compared to current NRC guidance. The results demonstrate an annular fuel design with homogenously blended gadolinium as a burnable absorber operates with greater safety margins during normal operation, allowing for additional operational flexibility. During normal operation, the core design utilizing Integral Fuel Burnable Absorber pins contained fuel pins which reached plenum pressures above 15.5 MPa by the end of the first fuel cycle and fuel pins experienced cladding hoop strains above 1 %. In the Gd core design, only two observed pins experienced plenum pressures above 15.5 MPa and no pins exceeded 1 % cladding hoop strain. During the control rod withdrawal scenario, plenum pressures for pins in both designs marginally exceeded system pressure, however neither experienced excessive hoop strain. The Gd core design experienced a maximum fuel temperature of 2418 K, which is significantly higher than the Integral Fuel Burnable Absorber design at 2157 K, but still within regulatory guidance. We predicted that the fuel in both could return to service after the CRW event. We also predicted that cladding would not fail during the Control Rod Ejection in either core design. Generally, the Integral Fuel Burnable Absorber core design performed with greater safety margin with regards to temperature during normal operation and the transient events. However, the Gd core design performed with greater safety margin regarding plenum pressure and hoop strain limits during normal operation and both transient events.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Robust deep learning framework for constitutive relations modeling

Modeling the full-range deformation behaviors of materials under complex loading and materials conditions is a significant challenge for constitutive relations (CRs) modeling. Here, we propose a general encoder-decoder deep learning framework that can model high-dimensional stress-strain data and complex loading histories with robustness and universal capability. The framework employs an encoder to project high-dimensional input information (e.g., loading history, loading conditions, and materials information) to a lower-dimensional hidden space and a decoder to map the hidden representation to the stress of interest. We evaluated various encoder architectures, including gated recurrent unit (GRU), GRU with attention, temporal convolutional network (TCN), and the Transformer encoder, on two complex stress-strain datasets that were designed to include a wide range of complex loading histories and loading conditions. All architectures achieved excellent test results with an root-mean-square error (RMSE) below 1 MPa. Additionally, we analyzed the capability of the different architectures to make predictions on out-of-domain applications, with an uncertainty estimation based on deep ensembles. The proposed approach provides a robust alternative to empirical/semi-empirical models for CRs modeling, offering the potential for more accurate and efficient materials design and optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Concrete shrinkage and creep under drying/wetting cycles

Concrete shrinkage and creep under variable hydric conditions are important factors for the safety and durability of concrete especially in nuclear reactor or nuclear waste storage background. A large (and long – more than 900 days) experimental campaign, conducted on two different concretes, has therefore been designed to study the strains of non loaded and loaded concretes submitted to drying and liquid water imbibition cycles. For the purposes of comparison, concrete strains and mass variations during drying only (50% RH) and/or following cycles of drying/rewetting were also recorded. This allowed the identification of desiccation shrinkage, basic creep and drying creep at 10 MPa of axial stress. Important results were found and have shown that the final mass and strain are not deeply modified by the introduction of a rewetting phase either for a loaded or a non loaded material.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chemically Recyclable Analogs of Styrene–Butadiene Copolymers Enabling Perfectly Linear Ethylene–Styrene Materials with Random Phenyl Distribution

Copolymerization of cyclopentene (CP) and 4-phenylcyclopentene (4PCP) at a full range of comonomer feed ratios is reported using Ru-based ring-opening metathesis polymerization (ROMP) yielding homogeneous copolymers analogous to poly(styrene-ran-1,4-butadiene) and poly(ethylene-ran-styrene) copolymers following hydrogenation under mild conditions. In all cases, total monomer conversions of 86%–92% yielded copolymers with compositions within 4% of monomer feeds. Analysis of equilibrium copolymerization thermodynamics, rarely performed on two cycloolefin monomers with low ring strain energies, provides rational design strategies for negotiating two monomers with different equilibrium monomer concentrations. Inverse-gated decoupled 13 C NMR analysis of dyad sequences on the resulting copolymer microstructures concludes a near-random distribution of comonomer units. The copolymers produced from ROMP have number-average molar masses up to 60 kg mol –1 , moderate dispersities (1.5 ± 0.1), and high trans olefin content (86% ± 2%) while glass-transitions temperatures follow the Fox equation and span the full range between homopolymer extremities of PCP (−96 °C) and P4PCP (17 °C). Unlike most prevulcanized elastomers, these materials undergo facile chemical recycling to monomer, producing complete ring-closing metathesis depolymerization (RCMD) of the polymer back to the CP comonomers. Quantitative olefin hydrogenation produced perfectly linear polyethylene with 4%–16% of the backbone carbons containing a phenyl pendant, analogous to ES copolymers with up to 71.5% w/w styrene units but with random distribution of the aromatic pendants. Thermal properties of these materials are discussed, which span from semicrystalline to amorphous, and with T g values notably less than the reported ES copolymer analogs at similar compositions.

animal feed↗
DOE OSTI2026

Performance of Heterostructural TaC/AlGaN Schottky Diodes Based on First Principles Electronic Structure Properties

Advances in ultra-wide bandgap materials, such as high Al-content AlxGa1-xN (AlGaN), are essential for next generation power electronics, but the requirement for lattice matched substrates is currently a significant obstacle. Recently, conductive TaC has emerged as a promising virtual substrate for AlGaN heteroepitaxy, with wurtzite (0001) AlxGa1-xN lattice-matched to rocksalt (111) TaC at x ~ 0.5. Thus, understanding and controlling the electronic properties of the TaC/AlGaN interface is key for developing technological applications based on TaC/AlGaN devices. Using density functional theory and electronic structure calculations, we here investigate TaC/Al0.5Ga0.5N interfaces, where we include explicit alloy models in the slab calculations. We predict the Schottky barrier height and the electric field discontinuity resulting from interface charges. Considering all possible combinations of (Ta, C) substrate termination, (Al/Ga, N) nucleation, and (Al/Ga, N) polarity, we construct a chemical potential phase diagram to identify the stable interfaces that can be accessed through variation of the synthesis conditions. The predicted interface electronic properties are implemented in device performance simulations to demonstrate a practical design for a strain-free, high-efficiency TaC/AlGaN Schottky diode with a low barrier height and without interface charges, underscoring the potential of TaC as a substrate for ultra-wide bandgap devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

A High-efficacy CRISPRi System for Gene Function Discovery in Zymomonas mobilis

Zymomonas mobilis is a promising biofuel producer due to its high alcohol tolerance and streamlined metabolism that efficiently converts sugar to ethanol. Z. mobilis genes are poorly characterized relative to those of model bacteria, hampering our ability to rationally engineer the genome with pathways capable of converting sugars from plant hydrolysates into valuable biofuels and bioproducts. Many of the unique properties that make Z. mobilis an attractive biofuel producer are controlled by essential genes; however, these genes cannot be manipulated using traditional genetic approaches (e.g., deletion or transposon insertion) because they are required for viability. CRISPR interference (CRISPRi) is a programmable gene knockdown system that can precisely control the timing and extent of gene repression, thus enabling targeting of essential genes. Here, we establish a stable, high-efficacy CRISPRi system in Z. mobilis that is capable of perturbing all genes—including essential genes. We show that Z. mobilis CRISPRi causes either strong knockdowns (>100-fold) using single guide RNA (sgRNA) spacers that perfectly match target genes or partial knockdowns using spacers with mismatches. We demonstrate the efficacy of Z. mobilis CRISPRi by targeting essential genes that are universally conserved in bacteria, are key to the efficient metabolism of Z. mobilis, or underlie alcohol tolerance. Our Z. mobilis CRISPRi system will enable comprehensive gene function discovery, opening a path to rational design of biofuel production strains with improved yields.

lignocellulosic hydrolysate↗
DOE OSTI2021

A combined biological and chemical flue gas utilization system towards carbon dioxide capture from coal-fired power plants (Final Report)

Photosynthetic algal cultivation has been intensively studied for CO 2 capture and utilization for several decades. The footprint for using algae to capture CO 2 emitted from carbon-intensive industrial processes (power plants, cement plants, and fermentation processes) is extremely large, which creates serious technical and economic hurdles that must be cleared if algal technologies are to be commercially implemented. Fortunately, algal biomass is rich in proteins, carbohydrates, and lipids, providing a good chemical source for organic absorbents and other value-added chemical feedstocks. In particular, amino acids from algal protein can be used to generate amino acid salt solutions that have been proven to be effective for capturing CO 2 . In order to take advantage of both algal cultivation and biomass utilization, the goal of the proposed project is to develop a combined biological and chemical system for coal-fired power plants for sequestering CO 2 in biological absorbents and generating value-added products. This approach significantly reduces the land and energy footprint of CO 2 capture, and minimizes capital and operational expenses. Three specific objectives are targeted: 1) optimizing the growth of the selected algal strain to maximize biomass accumulation from the coal-fired flue gas; 2) developing a cascade biomass utilization to produce amino acid absorbents, polyurethanes, biodiesel, and methane; and 3) conducting techno-economic analysis (TEA) and life cycle assessment (LCA) of the proposed process. Three key technical outcomes were achieved: (1) With the selected robust algal strain and unique photobioreactor design, long-term culture stability can be extended, and algal biomass productivity reached 0.5 g dry biomass/L/day year-round at a biomass concentration of 1.2 g/L in the pilot photobioreactor; (2) The biomass utilization process led to complete utilization of the algal biomass to produce amino acid salt absorbent, polyurethanes, and methane; and (3) The combined biological and chemical flue gas utilization process concluded a technically and economically feasible commercial-scale system that completely captures CO 2 in coal-fired flue gas with greatly reduced energy consumption.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Tuning Perovskites’ Hydration-Induced Chemical Expansion with Octahedral Tilt Angles

Hydration-induced strains in proton-conducting oxides compromise chemo-mechanical stability when these materials are applied in protonic ceramic electrochemical cells. Here, to develop design principles for zero-strain materials, we systematically studied the hydration coefficients of chemical expansion (CCEs) in perovskite (Sr, Ba)(Ce, Zr, Y)O 3–x solid solutions with in situ dilatometry and thermogravimetric analysis in the range of 430–630 °C. By including and decoupling a wide range of tolerance factors and lattice parameters, we were able to identify a minimum in hydration CCEs (0–0.02) at intermediate tolerance factor values (t ≈ 0.95). Conversely, despite expectations of lower CCEs in larger unit cells, no general trend in CCE versus lattice parameter was found, and opposite trends could be seen for Sr(Ce, Zr, Y)O 3–x versus Ba(Ce, Zr, Y)O 3–x separately. In situ neutron diffraction (ND) enabled atomistic insight. Upon decreasing t, chemical strain anisotropy increased, but this trend did not match the U-shaped dependence of macroscopic CCEs on t. Instead, perovskites with intermediate t, hosting intermediate octahedral tilt angles in the nominally dry state, underwent the largest change in the B–O–B angles during hydration. Accommodating hydration through decreasing B–O–B angles is beneficial because it does not result in large lattice parameter changes. We propose an intermediate tolerance factor as a simple structural descriptor to enable near-zero hydration strains in proton-conducting perovskites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evaluation of Strain and Exhaustion Limits for Vessels

Design rules for impulsively loaded vessels (ILVs) have been incorporated in Section VIII, Division 3 of the ASME Code since 2019, based upon earlier development of ASME Code Case 2564. These rules are particularly applicable to explosive containment vessels (ECVs) used to fully or partially contain the combustion products of explosives. Uses of these ECVs include containment of suspect luggage at airports, bomb disposal, containment of experiments on explosive devices, and destruction of chemical munitions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strain dependence of Auger recombination in 3 μm GaInAsSb/GaSb type-I active regions

We differentiate the effect of strain induced by lattice-mismatched growth from strain induced by mechanical deformation on cubic nonradiative Auger recombination in narrow-gap GaInAsSb/GaSb quantum well (QW) heterostructures. The typical reduction in the Auger coefficient observed with lattice-mismatched growth appears to be due to the concomitant compositional change rather than the addition of strain, with implications for mid-IR semiconductor laser design. We induced a range of internal compressive strain in five samples from -0.90% to -2.07% by varying the composition during the growth and mechanically induced a similar range of internal strain in analogous quantum well membrane samples. We performed time-resolved photoluminescence and differential reflectivity measurements to extract the carrier recombination dynamics, taken at 300 K with carrier densities from 2.7 × 10 18 cm -3 to 1.4 × 10 19 cm -3 . We observed no change with strain in the cubic Auger coefficient of samples that were strained mechanically, but we did observe a trend with strain in samples that were strained by the QW alloy composition. Measured Auger coefficients ranged from 3.0 × 1 0 - 29 cm 6 s -1 to 3.0 × 1 0 - 28 cm 6 s -1 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Automated Strain Construction for Biosynthetic Pathway Screening in Yeast

Automation accelerates the Design-Build-Test-Learn (DBTL) cycle for synthetic biology; however, most strain construction pipelines lack robotic integration. Here, in this study, we present the workflow design and source code for a modular, integrated protocol that automates the Build step in Saccharomyces cerevisiae. We programmed the Hamilton Microlab VANTAGE to integrate off-deck hardware via its central robotic arm, enabling automated steps that increased throughput to 2,000 transformations per week. We developed a user interface with the Hamilton VENUS software to support on-demand parameter customization. As a proof of concept, we screened a gene library in an engineered yeast strain producing verazine, a key intermediate in the biosynthesis of steroidal alkaloids. Our pipeline rapidly identified pathway bottlenecks and genes that enhanced verazine production by 2.0- to 5-fold. This technical note provides resources for synthetic biologists designing yeast workflows for biofoundries to screen libraries for pathway discovery/optimization, combinatorial biosynthesis, and protein engineering.

automation↗
DOE OSTI2024

Triple tandem trimer immunogens for HIV-1 and influenza nucleic acid-based vaccines

Recombinant native-like HIV-1 envelope glycoprotein (Env) trimers are used in candidate vaccines aimed at inducing broadly neutralizing antibodies. While state-of-the-art SOSIP or single-chain Env designs can be expressed as native-like trimers, undesired monomers, dimers and malformed trimers that elicit non-neutralizing antibodies are also formed, implying that these designs could benefit from further modifications for gene-based vaccination approaches. Here, we describe the triple tandem trimer (TTT) design, in which three Env protomers are genetically linked in a single open reading frame and express as native-like trimers. Viral vectored Env TTT induced similar neutralization titers but with a higher proportion of trimer-specific responses. The TTT design was also applied to generate influenza hemagglutinin (HA) trimers without the need for trimerization domains. Additionally, we used TTT to generate well-folded chimeric Env and HA trimers that harbor protomers from three different strains. In summary, the TTT design is a useful platform for the design of HIV-1 Env and influenza HA immunogens for a multitude of vaccination strategies.

60 APPLIED LIFE SCIENCES↗