Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A self-healing plastic ceramic electrolyte by an aprotic dynamic polymer network for lithium metal batteries

Abstract Oxide ceramic electrolytes (OCEs) have great potential for solid-state lithium metal (Li 0 ) battery applications because, in theory, their high elastic modulus provides better resistance to Li 0 dendrite growth. However, in practice, OCEs can hardly survive critical current densities higher than 1 mA/cm 2 . Key issues that contribute to the breakdown of OCEs include Li 0 penetration promoted by grain boundaries (GBs), uncontrolled side reactions at electrode-OCE interfaces, and, equally importantly, defects evolution (e.g., void growth and crack propagation) that leads to local current concentration and mechanical failure inside and on OCEs. Here, taking advantage of a dynamically crosslinked aprotic polymer with non-covalent –CH 3 ⋯CF 3 bonds, we developed a plastic ceramic electrolyte (PCE) by hybridizing the polymer framework with ionically conductive ceramics. Using in-situ synchrotron X-ray technique and Cryogenic transmission electron microscopy (Cryo-TEM), we uncover that the PCE exhibits self-healing/repairing capability through a two-step dynamic defects removal mechanism. This significantly suppresses the generation of hotspots for Li 0 penetration and chemomechanical degradations, resulting in durability beyond 2000 hours in Li 0 -Li 0 cells at 1 mA/cm 2 . Furthermore, by introducing a polyacrylate buffer layer between PCE and Li 0 -anode, long cycle life >3600 cycles was achieved when paired with a 4.2 V zero-strain cathode, all under near-zero stack pressure.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Thermoelastic constitutive equations for chemically hardening materials

Thermoelastic constitutive equations are derived for a material undergoing solidification or hardening as the result of a chemical reaction. The derivation is based upon a two component model whose composition is determined by the degree of hardening, and makes use of strain-energy considerations. Constitutive equations take the form of stress rate-strain rate relations, in which the coefficients are time-dependent functions of the composition. Specific results are developed for the case of a material of constant bulk modulus which undergoes a transition from an initial liquidlike state into an isotropic elastic solid. Potential applications are discussed.

Shaffer, B. W.↗
NASA NTRS2006

Mechanical Characterization of ZnSe Windows for Use With the Flow Enclosure Accommodating Novel Investigations in Combustion of Solids (FEANICS) Module

Mechanical and physical properties of ZnSe windows to be used with the FEANICS (Flow Enclosure Accommodating Novel Investigations in Combustion of Solids) experiments were measured in order to determine design allowables. The average Young s modulus, Poisson's ratio, equibiaxial fracture strength, flaw size, grain size, Knoop hardness, Vicker s hardness, and branching constant were 74.3 +/- 0.1 GPa, 0.31, 57.8 +/- 6.5 MPa, 21 +/- 4 mm, 43 +/- 9 microns, 0.97 +/- 0.02 GPa, 0.97 +/- 0.02 GPa, and 1.0 +/- 0.1 MPa(square root of)m, respectively. The properties of current ZnSe made by chemical vapor deposition are in good agreement with those measured in the 1970 s. The hardness of CVD ZnSe windows is about one-twentieth of the sapphire window being replaced, and about one-sixth of that of window glass. Thus the ZnSe window must be handled with great care. The large grain size relative to the inherent crack size implies the need to use single crystal crack growth properties in the design process. In order to determine the local failure stresses in one of the test specimens, a solution for the stresses between the support ring and the edge of a circular plate load between concentric rings was derived

Salem, Jonathan A.↗
NASA NTRS1993

Thermal expansivity, bulk modulus, and melting curve of H2O-ice VII to 20 GPa

Equation of state properties of ice VII and fluid H2O at high pressures and temperatures have been studied experimentally from 6 to 20 GPa and 300-700 K. The techniques involve direct measurements of the unit-cell volume of the solid using synchrotron X-ray diffraction with an externally heated diamond-anvil cell. The pressure dependencies of the volume and bulk modulus of ice VII at room temperature are in good agreement with previous synchrotron X-ray studies. The thermal expansivity was determined as a function of pressure and the results fit to a newly proposed phenomenological relation and to a Mie-Gruneisen equation of state formalism. The onset of melting of ice VII was determined directly by X-ray diffraction at a series of pressures and found to be in accord with previous volumetric determinations. Thermodynamic calculations based on the new data are performed to evaluate the range of validity of previously proposed equations of state for fluid water derived from static and shock-wave compression experiments and from simulations.

Fei, Yingwei↗
DOE OSTI2022

Carburization Kinetics of Zircalloy-4 and Its Implication for Small Modular Reactor Performance

Carburization of cladding materials has long been a concern for the nuclear industry and has led to the restricted use of high-thermal conductivity fuels such as uranium carbides. With the rise of small modular reactors (SMRs) that frequently implement a graphite core-block, carburization of reactor components is once more in the foreground as a potential failure mechanism. To ensure commercial viability for SMRs, neutron-friendly cladding materials such as Zr-based alloys are required. In this work, the carburization kinetics of Zircaloy-4 (Zry-4), for the temperature range 1073–1673 K (covering typical operating temperatures and off-normal scenarios) are established. The following Arrhenius relationship for the parabolic constant describing ZrC growth is derived: Kp (in μm2/s) = 609.35 exp(−1.505 × 105/RT)). Overall, the ZrC growth is sluggish below 1473 K which is within the operational temperature range of SMRs. In all cases the ZrC that forms from solid state reaction is hypo-stoichiometric, as confirmed through XRD. The hardness and elastic modulus of carburized Zry-4 are also examined and it is shown that despite the formation of a ZrC layer, C ingress in the Zry-4 bulk does not impact the mechanical response after carburization at 1073 K and 1473 K for 96 h.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Correlation of materials properties with the atomic density concept

Based on the hypothesis that the number of atoms per unit volume, accurately calculable for any substance of known real density and chemical composition, various characterizing parameters (energy levels of electrons interacting among atoms of the same or different kinds, atomic mass, bond intensity) were chosen for study. A multiple exponential equation was derived to express the relationship. Various properties were examined, and correlated with the various parameters. Some of the properties considered were: (1) heat of atomization, (2) boiling point, (3) melting point, (4) shear elastic modulus of cubic crystals, (5) thermal conductivity, and (6) refractive index for transparent substances. The solid elements and alkali halides were the materials studied. It is concluded that the number of different properties can quantitively be described by a common group of parameters for the solid elements, and a wide variety of compounds.

Source record↗
NASA NTRS1992

Sensors and sensor systems for guidance and navigation II; Proceedings of the Meeting, Orlando, FL, Apr. 22, 23, 1992

Topics discussed in this volume include aircraft guidance and navigation, optics for visual guidance of aircraft, spacecraft and missile guidance and navigation, lidar and ladar systems, microdevices, gyroscopes, cockpit displays, and automotive displays. Papers are presented on optical processing for range and attitude determination, aircraft collision avoidance using a statistical decision theory, a scanning laser aircraft surveillance system for carrier flight operations, star sensor simulation for astroinertial guidance and navigation, autonomous millimeter-wave radar guidance systems, and a 1.32-micron long-range solid state imaging ladar. Attention is also given to a microfabricated magnetometer using Young's modulus changes in magnetoelastic materials, an integrated microgyroscope, a pulsed diode ring laser gyroscope, self-scanned polysilicon active-matrix liquid-crystal displays, the history and development of coated contrast enhancement filters for cockpit displays, and the effect of the display configuration on the attentional sampling performance.

Welch, Sharon S.↗
NASA NTRS2003

Using Plate Finite Elements for Modeling Fillets in Design, Optimization, and Dynamic Analysis

A methodology has been developed that allows the use of plate elements instead of numerically inefficient solid elements for modeling structures with 90 degree fillets. The technique uses plate bridges with pseudo Young's modulus (Eb) and thickness (tb) values placed between the tangent points of the fillets. These parameters are obtained by solving two nonlinear simultaneous equations in terms of the independent variables rlt and twallt. These equations are generated by equating the rotation at the tangent point of a bridge system with that of a fillet, where both rotations are derived using beam theory. Accurate surface fits of the solutions are also presented to provide the user with closed-form equations for the parameters. The methodology was verified on the subcomponent level and with a representative filleted structure, where the technique yielded a plate model exhibiting a level of accuracy better than or equal to a high-fidelity solid model and with a 90-percent reduction in the number of DOFs. The application of this method for parametric design studies, optimization, and dynamic analysis should prove extremely beneficial for the finite element practitioner. Although the method does not attempt to produce accurate stresses in the filleted region, it can also be used to obtain stresses elsewhere in the structure for preliminary analysis. A future avenue of study is to extend the theory developed here to other fillet geometries, including fillet angles other than 90 and multifaceted intersections.

Brown, A. M.↗
NASA NTRS1997

Composite Properties of Polyimide Resins Made From "Salt-Like" Solution Precursors

Recent work in high temperature materials at NASA Langley Research Center (LaRC (trademark)) have led to the development of new polyimide resin systems with very attractive properties. The majority of the work done with these resin systems has concentrated on determining engineering mechanical properties of composites prepared from a poly(amide acid) precursor. Three NASA Langley-developed polyimide matrix resins, LaRC (trademark) -IA, LaRC (trademark) -IAX, and LaRC (trademark) -8515, were produced via a salt-like process developed by Unitika Ltd. The 'salt-like' solutions (sixty-five percent solids in NMP) were prepregged onto Hexcel IM7 carbon fiber using the NASA LaRC Multipurpose Tape Machine. Process parameters were determined and composite panels fabricated. Mechanical properties are presented for these three intermediate modulus carbon fiber/polyimide matrix composites and compared to existing data on the same polyimide resin systems and IM7 carbon fiber manufactured via poly(amide acid) solutions (thirty-five percent solids in NMP). This work studies the effects of varying the synthetic route on the processing and mechanical properties of polyimide composites.

Cano, Roberto J.↗
DOE OSTI2023

High‐Throughput Evaluation of Hardening Coefficients of Eight Alloying Elements in Magnesium

Liquid–solid diffusion couples (LSDCs) are employed to generate a composition gradient in the single‐phase hexagonal closed‐packed (hcp) solid solution with compositions up to the solubility limit of various solutes in Mg. Nanoindentation scanning across the composition gradient in LSDCs allows effective evaluation of composition‐dependent hardness of eight alloying elements (Al, Ca, Ce, Gd, Li, Sn, Y, and Zn) in the hcp Mg phase. The hardening coefficients, an indicator of the potency of solid‐solution hardening, are evaluated from the measured composition‐hardness data and correlated with various materials properties such as atomic radius, shear modulus, and elastic modulus of the solutes. The rank of hardening potency of Al, Gd, Sn, Y, and Zn measured by nanoindentation is in good agreement with that measured by microindentation reported in the literature. The hardening coefficient (potency) from the strongest to the weakest is Ce > Ca > Y ≈ Gd > Zn > Al ≈ Sn > Li in Mg‐based hcp binary solid solutions. The hardening coefficient is found to be closely correlated with the strengthening potency.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring grain growth and solid solution strengthening of single-phase CrCoNi medium-entropy alloys by solute selection

In the present study, we selected solutes to be added to the CrCoNi medium-entropy alloy (MEA) based on the mismatch of self-diffusion activation energy (SDQ) between the alloying elements and constituent elements of the matrix, and then investigated their grain growth behavior and mechanical properties. Mo and Al were selected as the solutes for investigation primarily because they have higher and lower SDQ, respectively, than those of the matrix elements; a secondary factor was their higher and lower shear modulus. Their concentrations were fixed at 3 at.% each because previous work had shown these compositions to be single-phase solid solutions with the face-centered cubic structure. Three alloys were produced by arc melting, casting, homogenizing, cold rolling and annealing at various temperatures and times to produce samples with different grain sizes. They were (a) the base alloy CrCoNi, (b) the base alloy plus 3 at.% Mo, and (c) the base alloy plus 3 at.% Al. The activation energies for grain growth of the CrCoNi, CrCoNi-3Mo and CrCoNi-3Al MEAs were found to be ~251, ~368 and ~219 kJ/mol, respectively, consistent with the notion that elements with higher SDQ (in this study Mo) retard grain growth (likely by a solute-drag effect), whereas those with lower values (Al) accelerate grain growth. The room-temperature tensile properties show that Mo increases the yield strength by ~40% but Al addition has a smaller strengthening effect consistent with their relative shear moduli. The yield strength as a function of grain size for the three singlephase MEAs follows the classical Hall-Petch relationship with much higher slopes (> 600 MPa μm -0.5 ) than traditional solid solutions. Furthermore, this work shows that the grain growth kinetics and solid solution strengthening of the CrCoNi MEA can be tuned by selecting solute elements that have appropriate diffusion and physical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-pressure crystal structure and equation of state of ferromagnesian jeffbenite: implications for stability in the transition zone and uppermost lower mantle

Jeffbenite, ideally Mg 3 Al 2 Si 3 O 12 , has been identified as inclusions in super-deep diamonds originating from depths that exceed 300 km. Although Mg-end member jeffbenite has limited stability at upper-mantle conditions, iron-bearing jeffbenite may have broader P–T stability that extends to the transition zone or uppermost lower mantle, incorporating significant amounts of ferric iron. Using synchrotron-based, single-crystal X-ray diffraction (XRD) and synchrotron Mössbauer spectroscopy (SMS) at pressures up to 29 GPa, we report the crystal structure, compressibility, and likely spin transition of iron in ferromagnesian jeffbenite (Mg 2.32 Al 0.03 Fe 2+ 1.28 Fe 3+ 1.77 Si 2.85 O 12 ). High-pressure structure refinements reveal that Fe 3+ substitution for Si in the T2 site, which shares edges with the M2 octahedron, likely stabilizes jeffbenite at high pressure, because it increases the cation-to-cation distance between these sites. Although ferromagnesian jeffbenite does not undergo a structural phase transition below 30 GPa, SMS hyperfine parameters suggest the onset of an electronic spin transition of iron from high-spin (HS) to low-spin (LS) at around 22 GPa, which may increase its stability at high pressures. Pressure–volume data were fit to a third order Birch–Murnaghan equation of state, resulting in V o = 816.54(9), K To = 181.54(1.39), and K' T0 = 2.76(14). These equation of state parameters are applicable to evaluating the encapsulation pressures of super-deep diamonds. The density and bulk modulus of ferromagnesian jeffbenite are similar to or higher than pyrope–almandine, pyrope–majorite, and skiagite–majorite solid solution garnets, further suggesting that jeffbenite may be an important ferric–iron silicate in the deeper parts of the mantle transition zone and uppermost lower mantle. Furthermore, future studies on the influence of temperature and oxidation state on the stability and equations of state of iron-bearing jeffbennite are still needed to determine what role, if any, jeffbenite plays in transition-zone mineralogy.

58 GEOSCIENCES↗
DOE OSTI2025

Harnessing Machine Learning to Predict MoS 2 Solid Lubricant Performance

Physical vapor deposited (PVD) molybdenum disulfide (MoS 2 ) solid lubricant coatings are an exemplar material system for machine learning methods due to small changes in process variables often causing large variations in microstructure and mechanical/tribological properties. Here, in this work, a gradient boosted regression tree machine learning method is applied to an existing experimental data set containing process, microstructure, and property information to create deeper insights into the process-structure–property relationships for molybdenum disulfide (MoS 2 ) solid lubricant coatings. The optimized and cross-validated models show good predictive capabilities for density, reduced modulus, hardness, wear rate, and initial coefficients of friction. The contribution of individual deposition variables (i.e., argon pressure, deposition power, target conditioning) on coating properties is highlighted through feature importance. The process-property relationships established herein show linear and non-linear relationships and highlight the influence of uncontrolled deposition variables (i.e., target conditioning) on the tribological performance.

MoS2↗
DOE OSTI2022

Molecular simulations and NMR reveal how lipid fluctuations affect membrane mechanics

Lipid bilayers form the main matrix of functional cell membranes, and their dynamics underlie a host of physical and biological processes. Here we show that elastic membrane properties and collective molecular dynamics (MD) are related by the mean-square amplitudes (order parameters) and relaxation rates (correlation times) of lipid acyl chain motions. We performed all-atom MD simulations of liquid-crystalline bilayers that allow direct comparison with carbon-hydrogen (CH) bond relaxations measured with NMR spectroscopy. Previous computational and theoretical approaches have assumed isotropic relaxation, which yields inaccurate description of lipid chain dynamics and incorrect data interpretation. Instead, the new framework includes a fixed bilayer normal (director axis) and restricted anisotropic motion of the CH bonds in accord with their segmental order parameters, enabling robust validation of lipid force fields. Simulated spectral densities of thermally excited CH bond fluctuations exhibited well-defined spin-lattice (Zeeman) relaxations analogous to those in NMR measurements. Their frequency signature could be fit to a simple power-law function, indicative of nematic-like collective dynamics. Moreover, calculated relaxation rates scaled as the squared order parameters yielding an apparent K C modulus for bilayer bending. Our results show a strong correlation with K C values obtained from solid-state NMR studies of bilayers without and with cholesterol as validated by neutron spin-echo measurements of membrane elasticity. The simulations uncover a critical role of interleaflet coupling in membrane mechanics and thus provide important insights into molecular sites of emerging elastic properties within lipid bilayers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Yielding Behavior of Bottlebrush and Linear Block Copolymers

Block copolymers can exhibit a pronounced yield stress, but the impact of molecular architecture, chemistry, and self-assembly on macroscopic rheology remains poorly understood. Here, we study the linear-viscoelastic and yield-stress fluid behavior of two architectures—bottlebrush copolymers (with statistical or blocky sequences) and linear diblocks—that self-assemble into body-centered cubic (BCC) spheres and hexagonally close-packed cylinders (HEX). The dynamic properties of these polymers were probed by oscillatory frequency and amplitude sweeps at temperatures well below the order–disorder transition (TODT) to furnish insights into the yielding transition. All BCC-forming polymers have a similar signature of yielding: smaller yield strains (γ yBCC ≈ 0.053 < γ y,HEX ≈ 0.18), sharper solid–liquid transitions, and better reversibility than HEX. Statistical bottlebrushes show the most frequency-independent structural modulus (G 0 ) and no signs of defect relaxation. A simple power-law relationship captures the dependence of the normalized structural modulus (G 0 /RT) on the inter-micelle distance (d) across different architectures and morphologies [G 0 /(RT) = 1.31 × 10 4 (nm 2.6 mol/m 3 ) d –2.6 ]. These studies establish quantitative structure–property relationships that are relevant in contemporary applications, for example, extrusion-based 3D printing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental Assessment of Elastic Modulus vs. Relative Density for Stretch- and Bend-Dominated Lattices

This project was designed to study the possibility of using structural properties of lattices to replicate the material properties of certain hard to manufacture designs and use topology optimization to determine the lattice type and density required to mimic these properties. The integration of additively manufactured lattice structures with topology optimization highlights the need for well characterized mechanical properties and uncertainty analyses to insure these optimized structures respond as predicted. Stereolithographically printed octet and rhombic dodecahedron lattices were manufactured at 10%, 25% and 65% density by volume. As a separate task, yet integrated into this work, finite element analysis (FEA) was used to predict the printed lattice’s mechanical properties, which were then compared to our experimental results. After comparing FEA and experimentallymeasured elastic moduli, it was determined that the FEA provides highly reliable predictions for the modulus of these printed lattice structures. These lattices also exhibited greater tensile stiffness than that of the solid material demonstrating the flexibility that lattices provide to designing parts with designer structural properties. The accurate printing and reliable modeling of these lattices will enable topology optimization of complex parts from well-characterized rhombic dodecahedron and octet lattice structures of varying densities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of Best-Practices and Computationally Inexpensive Radiative Exchange Models for Discrete Element Method Modeling of Aluminosilicate Particles in Concentrating Solar Power Environments

Chemically inert, aluminosilicate based particles have been investigated as both a thermal transport and sensible energy storage medium for concentrating solar power facilities. These particles will experience a wide range of operating temperatures (300-1000 K) and handling conditions (dense to dilute falling particle curtains, dense granular flows, or dense structures), requiring specially-designed and optimized infrastructures. The relative influence of collisional and frictional interactions between particles varies based on temperature-dependent particulate properties and greatly impacts the bulk, granular flow behavior. These underlying physics are captured using discrete element method modeling tools. However, this modeling method is computationally expensive as each particle position and interaction is tracked during the simulation. These modeling methods are further complicated by introducing temperature-dependent particle properties, high-temperature radiative exchange, and directional irradiation sources experienced by granular flows in concentrating solar power environments. In this study, coupled experimental and numerical slump testing of aluminosilicate particles was performed and computationally efficient radiative exchange models were evaluated to establish best-practices for discrete element method models for concentrating solar power environments. The three particle types investigated included Carbobead HSP 30 /60, Carbobead CP 30/60, and Granusil 4030. Existing modeling limitations and computationally-efficient multi-modal heat transfer models were evaluated using Aspherix®, a commercial discrete element method software. High-temperature (< 1073 K) slump testing of aluminosilicate particles was performed to investigate the deviation between experimentally-observed and numerically-predicted angles of repose introduced by computation-time reduction practices including the relaxation of the particle elastic modulus and coarse-graining. Coarse-graining is used to use a single modeled particle that is representative of a collection of smaller particles, decreasing the computational cost at the expense of geometric accuracy. Additionally, relaxation of the elastic modulus is used to reduce computational time at the expense of an increased, modeled particle overlap. Prior studies have determined that aluminosilicate particles retain a high elastic modulus at high temperatures (< 1073 K), requiring small simulation timesteps to ensure resolved contact forces resemble appropriate solid mechanics. A parametric study was performed to evaluate the influence of computation time improvements on the deviation between experimental and modeled angle of repose across high temperatures < 1073 K. Additionally, numerical case studies were performed on candidate particle systems at varying porosities and temperatures. These studies were performed to investigate the influence of computationally-efficient radiative-exchange modeling methods coupled to Aspherix® on modeled accuracy and computation time. The recently-developed distance-based approximation was evaluated in estimating radiative exchange between particles and participating surfaces located in close proximity. The distance based approximation was developed to use tabulated estimates of the radiative distribution factor between individual particles and surfaces in close proximity (< 40 particle radii). These methods were expanded to the aluminosilicate particles of interest, including the influence of particle size distributions. To capture radiative exchange between particles and surfaces not in close proximity (> 40 particle radii) and to capture the absorption of directional irradiation from concentrating solar resources, a volumetrically-averaged radiative distribution factor was calculated between the modeled granular flow and surfaces using Monte Carlo ray-tracing for participating media. Volume-averaged absorption and scattering coefficients were predicted using a volumetric discretization of the modeled domain with monodisperse approximations based on geometric optics and experimentally-determined scattering phase functions for aluminosilicate particles.

14 SOLAR ENERGY↗
DOE OSTI2022

Task-Specific Phosphonium Iongels by Fast UV-Photopolymerization for Solid-State Sodium Metal Batteries

Sodium metal batteries are an emerging technology that shows promise in terms of materials availability with respect to lithium batteries. Solid electrolytes are needed to tackle the safety issues related to sodium metal. In this work, a simple method to prepare a mechanically robust and efficient soft solid electrolyte for sodium batteries is demonstrated. A task-specific iongel electrolyte was prepared by combining in a simple process the excellent performance of sodium metal electrodes of an ionic liquid electrolyte and the mechanical properties of polymers. The iongel was synthesized by fast (<1 min) UV photopolymerization of poly(ethylene glycol) diacrylate (PEGDA) in the presence of a saturated 42%mol solution of sodium bis(fluorosulfonyl)imide (NaFSI) in trimethyl iso-butyl phosphonium bis(fluorosulfonyl)imide (P111i4FSI). The resulting soft solid electrolytes showed high ionic conductivity at room temperature (≥10 -3 S cm -1 ) and tunable storage modulus (10 4 –10 7 Pa). Iongel with the best ionic conductivity and good mechanical properties (Iongel10) showed excellent battery performance: Na/iongel/NaFePO 4 full cells delivered a high specific capacity of 140 mAh g -1 at 0.1 C and 120 mAh g -1 at 1 C with good capacity retention after 30 cycles.

25 ENERGY STORAGE↗