SEARCH · Engineering Papers

Results for “power coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1957

Turbulence in the Wake of a Thin Airfoil at Low Speeds

Experiments have been made to determine the nature of turbulence in the wake of a two-dimensional airfoil at low speeds. The experiments were motivated by the need for data which can be used for analysis of the tail-buffeting problem in aircraft design. Turbulent intensity and power spectra of the velocity fluctuations were measured at a Reynolds number of 1.6 x 10(exp 5) for several angles of attack. Total-head measurements were also obtained in an attempt to relate steady and fluctuating wake properties. Mean-square downwash was found to have nearly the same dependence on vertical position in the wake as that shown by total-head loss. For this particular wing, turbulent intensity, integrated across the wake, increased roughly as the 3/2 power of the drag coefficient. Power-spectrum measurements indicated a decrease in frequency as wing angle of attack was increased. The average frequency in the wake was proportional to the ratio of mean wake velocity to wake width.

Campbell, George S.↗

NASA NTRS1974

Experimental and analytical sonic nozzle discharge coefficients for Reynolds numbers up to 8 x 10 to the 6th power

Sonic discharge coefficients are presented for two different geometry flow nozzles using nitrogen gas at high pressures where real gas corrections are significant. Throat Reynolds number range extended up to 8 million. Experimentally obtained coefficients for a nozzle with a continuous and finite radius of curvature agreed with those obtained analytically to within 0.2 percent. Experimental coefficients for a long radius ASME nozzle agreed to within 1/4 percent to an empirical equation representing the most probable subsonic discharge coefficient.

Szaniszlo, A. J.↗

NASA NTRS1975

Experimental and analytical sonic nozzle discharge coefficients for Reynolds numbers up to 8 x 10 to the 6th power

Sonic discharge coefficients are obtained for two different geometry flow nozzles using high-pressure nitrogen gas (100 atm) with significant real-gas flow corrections. Throat Reynolds number range extended up to 8 million. Discharge coefficients for both nozzles monotonically increase in value at the high throat Reynolds numbers. The 95-percent confidence band for each nozzle is shown. Analytical discharge coefficients for the continuous and finite radius of curvature nozzle are presented. These analytical results for the laminar and turbulent boundary-layer cases are compared to experimental values for sonic flow. Experimental values are also compared to values calculated from the best empirical curve fit equation for subsonic flow.

Szaniszlo, A. J.↗

NASA NTRS1944

Effect of Mach and Reynolds Numbers on the Power-Off Maximum Lift Coefficient Obtainable on a P-39N-1 Airplane as Determined in Flight

Flight tests were conducted on a Bell P-39N-1 airplane to determine the variation with Mach and Reynolds numbers of the maximum lift coefficient obtainable. The tests were made with the propeller in the constant-speed high-pitch setting and with the power off in order to minimize the effect of power and the propeller. The investigation covered a Mach number range of 0.146 to 0.655 and a Reynolds-number range of 4,900,000 to 17,100,000.The results of the investigation indicated that the maximum lift coefficient obtainable decreased markedly with an increase in Mach number for a given Reynolds number and exhibited a tendency to increase with an increase in Reynolds number for a given Mach number up to a Mach number of 0.55.

James M Nissen↗

NASA NTRS1987

Sound radiation from single and annular stream nozzles, with modal decomposition of in-duct acoustic power

An experimental program was carried out to study the acoustic characteristics of single and annular stream duct-nozzle systems at various flow conditions by using a refined acoustic impulse technique. In this technique, signal synthesis and signal averaging processes are incorporated to generate a desired impulsive signal from acoustic driver(s) and to eliminate background noise (flow noise) from in-duct and far field signals, respectively. The contribution of higher order modes to incident reflected and transmitted acoustic powers is accounted for by using a modal decomposition process. The annular stream terminations were tested statically at various annular stream flow velocities with no inner stream flow. The results derived from the experiments include in-duct acoustic powers, termination reflection coefficients, transmission coefficients, far field power, and acoustic dissipation.

Salikuddin, M.↗

NASA NTRS2000

A Common Calibration Source Framework for Fully-Polarimetric and Interferometric Radiometers

Two types of microwave radiometry--synthetic thinned array radiometry (STAR) and fully-polarimetric (FP) radiometry--have received increasing attention during the last several years. STAR radiometers offer a technological solution to achieving high spatial resolution imaging from orbit without requiring a filled aperture or a moving antenna, and FP radiometers measure extra polarization state information upon which entirely new or more robust geophysical retrieval algorithms can be based. Radiometer configurations used for both STAR and FP instruments share one fundamental feature that distinguishes them from more 'standard' radiometers, namely, they measure correlations between pairs of microwave signals. The calibration requirements for correlation radiometers are broader than those for standard radiometers. Quantities of interest include total powers, complex correlation coefficients, various offsets, and possible nonlinearities. A candidate for an ideal calibration source would be one that injects test signals with precisely controllable correlation coefficients and absolute powers simultaneously into a pair of receivers, permitting all of these calibration quantities to be measured. The complex nature of correlation radiometer calibration, coupled with certain inherent similarities between STAR and FP instruments, suggests significant leverage in addressing both problems together. Recognizing this, a project was recently begun at NASA Goddard Space Flight Center to develop a compact low-power subsystem for spaceflight STAR or FP receiver calibration. We present a common theoretical framework for the design of signals for a controlled correlation calibration source. A statistical model is described, along with temporal and spectral constraints on such signals. Finally, a method for realizing these signals is demonstrated using a Matlab-based implementation.

Kim, Edward J.↗

NASA NTRS1982

Mode Propagation in Nonuniform Circular Ducts with Potential Flow

A previously reported closed form solution is expanded to determine effects of isentropic mean flow on mode propagation in a slowly converging-diverging duct, a circular cosh duct. On the assumption of uniform steady fluid density, the mean flow increases the power transmission coefficient. The increase is directly related to the increase of the cutoff ratio at the duct throat. With the negligible transverse gradients of the steady fluid variables, the conversion from one mode to another is negligible, and the power transmission coefficient remains unchanged with the mean flow direction reversed. With a proper choice of frequency parameter, many different modes can be made subject to a single value of the power transmission loss. A systematic method to include the effects of the gradients of the steady fluid variables is also described.

Cho, Y. C.↗

NASA NTRS1982

Mode propagation in nonuniform circular ducts with potential flow

A previously reported closed form solution is expanded to determine effects of isentropic mean flow on mode propagation in a slowly converging-diverging duct - a circular cosh duct. On the assumption of uniform steady fluid density, the mean flow increases the power transmission coefficient. The increase is directly related to the increase of the cutoff ratio at the duct throat. With the negligible transverse gradients of the steady fluid variables, the conversion from one mode to another is negligible, and the power transmission coefficient remains unchanged with the mean flow direction reversed. With a proper choice of frequency parameter, many different modes can be made subject to a single value of the power transmission loss. The paper also describes a systematic method to include the effects of the gradients of the steady fluid variables.

Cho, Y. C.↗

NASA NTRS2011

Enhancements in Deriving Smoke Emission Coefficients from Fire Radiative Power Measurements

Smoke emissions have long been quantified after-the-fact by simple multiplication of burned area, biomass density, fraction of above-ground biomass, and burn efficiency. A new algorithm has been suggested, as described in Ichoku & Kaufman (2005), for use in calculating smoke emissions directly from fire radiative power (FRP) measurements such that the latency and uncertainty associated with the previously listed variables are avoided. Application of this new, simpler and more direct algorithm is automatic, based only on a fire's FRP measurement and a predetermined coefficient of smoke emission for a given location. Attaining accurate coefficients of smoke emission is therefore critical to the success of this algorithm. In the aforementioned paper, an initial effort was made to derive coefficients of smoke emission for different large regions of interest using calculations of smoke emission rates from MODIS FRP and aerosol optical depth (AOD) measurements. Further work had resulted in a first draft of a 1 1 resolution map of these coefficients. This poster will present the work done to refine this algorithm toward the first production of global smoke emission coefficients. Main updates in the algorithm include: 1) inclusion of wind vectors to help refine several parameters, 2) defining new methods for calculating the fire-emitted AOD fractions, and 3) calculating smoke emission rates on a per-pixel basis and aggregating to grid cells instead of doing so later on in the process. In addition to a presentation of the methodology used to derive this product, maps displaying preliminary results as well as an outline of the future application of such a product into specific research opportunities will be shown.

Ellison, Luke↗

NASA NTRS2004

Quantification of Inlet Impedance Concept and a Study of the Rayleigh Formula for Noise Radiation from Ducted Fan Engines

This paper addresses two aspects of duct propagation and radiation which can contribute to more efficient fan noise predictions. First, we assess the effectiveness of Rayleigh's formula as a ducted fan noise prediction tool. This classical result which predicts the sound produced by a piston in a flanged duct is expanded to include the uniform axial inflow case. Radiation patterns using Rayleigh's formula with single radial mode input are compared to those obtained from the more precise ducted fan noise prediction code TBIEM3D. Agreement between the two methods is excellent in the peak noise regions both forward and aft. Next, we use TBIEM3D to calculate generalized radiation impedances and power transmission coefficients. These quantities are computed for a wide range of operating parameters. Results were obtained for higher Mach numbers, frequencies, and circumferential mode orders than have been previously published. Viewed as functions of frequency, calculated trends in lower order inlet impedances and power transmission coefficients are in agreement with known results. The relationships are more oscillatory for higher order modes and higher Mach numbers.

Posey, Joe W.↗

NASA NTRS1988

Venus - Surface electromagnetic properties

Pioneer Venus high-angle radar imaging data are used here to correct values of the specular power reflection coefficient for the effects of diffusely scattering small-scale surface roughness. A value of 5.0 + or - 0.9 is found for the average dielectric permittivity of the rolling plains and lowlands, suggesting that most of the Venus surface is overlain by at most only a few cm of soil or dust. The unexpectedly high values of power reflection coefficient are confirmed by observations of correspondingly low values of radiothermal emission. Thus there can be little doubt that most of the highlands contain significant amounts of a conducting mineral near the surface.

Pettengill, Gordon H.↗

NASA NTRS1977

Mathematical models for the reflection coefficients of lossy dielectric half-spaces with application to transient responses of chirped pulses

Reflection coefficients are found at normal incidence for a large class of homogeneous lossy half-spaces with a one-dimensionally inhomogeneous or stratified lossy layer on top. Solutions are in terms of Hankel functions of complex argument to decrease cancellation error at high frequencies. One special case is that of layers on a homogeneous half-space where the dielectric constant in each layer may vary in a quite general manner. A Wronskian is used to insure the critical computations are correct. The reflection of chirped pulses is considered. Solutions are obtained by applying the fast Fourier transform. It is found that for a typical relatively long normalized 'long' pulse the power reflected as a function of time is essentially the power reflection coefficient for the frequencies swept out, whereas for a relatively short 'long' pulse, with the same relative change in frequency and the same number of oscillations there is only the uniform attenuation by the power reflection coefficient of the center frequency. By a 'long' pulse we mean a pulse whose spatial length is long compared to the thickness of the reflecting layer.

Evans, D. D.↗

NASA NTRS1954

Lift and moment coefficients expanded to the seventh power of frequency for oscillating rectangular wings in supersonic flow and applied to a specific flutter problem

Linearized theory for compressible unsteady flow is used to derive the velocity potential and lift and moment coefficients in the form of oscillating rectangular wing moving at a constant supersonic speed. Closed expressions for the velocity potential and lift and moment coefficients associated with pitching and translation are given to seventh power of the frequency. These expressions extend the range of usefulness of NACA report 1028 in which similar expressions were derived to the third power of the frequency of oscillation. For example, at a Mach number of 10/9 the expansion of the potential to the third power is an accurate representation of the potential for values of the reduced frequency only up to about 0.08; whereas the expansion of the potential to the seventh power is an accurate representation for values of the reduced frequency up to about 0.2. The section and total lift and moment coefficients are discussed with the aid of several figures. In addition, flutter speeds obtained in the Mach number range from 10/9 to 10/6 for a rectangular wing of aspect ratio 4.53 by using section coefficients derived on the basis of three-dimensional flow are compared with flutter speeds for this wing obtained by using coefficients derived on the basis of two-dimensional flow.

Nelson, Herbert C↗

NASA NTRSDate not supplied

Aeropropulsive Assessment of a BLI Tail-Cone Thruster Propulsion System for the NASA Common Research Model and a Transonic Truss-Braced Wing Configuration

This paper presents an investigation into the potential benefits of a boundary layer ingestion(BLI) aft fuselage propulsion system, or tail-cone thruster (TCT), when applied to two transport category aircraft: a conventional tube-and-wing configuration based on the NASA Common Research Model (CRM) and a transonic truss-braced wing (TTBW) configuration. Through the ingestion of low-momentum flow developed over the airframe of an aircraft, the TCT propulsion system technology can reduce overall power consumption and hence fuel burn and emissions. However, an accurate assessment of this potential requires the application of high-fidelity analysis tools that can capture the relevant propulsion-airframe integration effects, at least to first order. Toward this end, the present study employs aeropropulsive analysis tools based on the Reynolds-averaged Navier-Stokes equations to estimate the power savings coefficient, measured relative to equivalent non-BLI configurations of a given airframe. Results indicate shaft power savings of 4.1% and 5.9% can be obtained for the boundary-layer ingesting TCT configuration of the CRM and TTBW, respectively. The present study also examines the coupling between airframe aerodynamics and the inlet flow distortion experienced by the TCT of a given aircraft configuration through airframe component sensitivity studies.

AATT↗

NASA NTRS2005

Small-Scale Drop Size Variability: Impact on Estimation of Cloud Optical Properties

Most cloud radiation models and conventional data processing techniques assume that the mean number of drops of a given radius is proportional to volume. The analysis of microphysical data on liquid water drop sizes shows that, for sufficiently small volumes, this proportionality breaks down; the number of cloud drops of a given radius is instead proportional to the volume raised to a drop size-dependent nonunit power. The coefficient of proportionality, a generalized drop concentration, is a function of the drop size. For abundant small drops the power is unity as assumed in the conventional approach. However, for rarer large drops, it falls increasingly below unity. This empirical fact leads to drop clustering, with the larger drops exhibiting a greater degree of clustering. The generalized drop concentration shows the mean number of drops per cluster, while the power characterizes the occurrence frequency of clusters. With a fixed total number of drops in a cloud, a decrease in frequency of clusters is accompanied by a corresponding increase in the generalized concentration. This initiates a competing process missed in the conventional models: an increase in the number of drops per cluster enhances the impact of rarer large drops on cloud radiation while a decrease in the frequency suppresses it. Because of the nonlinear relationship between the number of clustered drops and the volume, these two opposite tendencies do not necessarily compensate each other. The data analysis suggests that clustered drops likely have a stronger radiative impact compared to their unclustered counterpart; ignoring it results in underestimation of the contribution from large drops to cloud horizontal optical path.

Knyazikhin, Y.↗

NASA NTRS2023

Reconfigurations in Brain Networks Upon Awakening From Slow Wave Sleep: Interventions and Implications in Neural Communication

Sleep inertia is the brief period of impaired alertness and performance experienced immediately after waking. Little is known about the neural mechanisms underlying this phenomenon. A better understanding of the neural processes during sleep inertia may offer insight into the awakening process. We observed brain activity every 15 min for 1 hr following abrupt awakening from slow wave sleep during the biological night. Using 32-channel electroencephalography, a network science approach, and a within-subject design, we evaluated power, clustering coefficient, and path length across frequency bands under both a control and a polychromatic short-wavelength-enriched light intervention condition. We found that under control conditions, the awakening brain is typified by an immediate reduction in global theta, alpha, and beta power. Simultaneously, we observed a decrease in the clustering coefficient and an increase in path length within the delta band. Exposure to light immediately after awakening ameliorated changes in clustering. Our results suggest that long-range network communication within the brain is crucial to the awakening process and that the brain may prioritize these long-range connections during this transitional state. Our study highlights a novel neurophysiological signature of the awakening brain and provides a potential mechanism by which light improves performance after waking.

EEG↗

NASA NTRS2015

Skylon Aerodynamics and SABRE Plumes

An independent partial assessment is provided of the technical viability of the Skylon aerospace plane concept, developed by Reaction Engines Limited (REL). The objectives are to verify REL's engineering estimates of airframe aerodynamics during powered flight and to assess the impact of Synergetic Air-Breathing Rocket Engine (SABRE) plumes on the aft fuselage. Pressure lift and drag coefficients derived from simulations conducted with Euler equations for unpowered flight compare very well with those REL computed with engineering methods. The REL coefficients for powered flight are increasingly less acceptable as the freestream Mach number is increased beyond 8.5, because the engineering estimates did not account for the increasing favorable (in terms of drag and lift coefficients) effect of underexpanded rocket engine plumes on the aft fuselage. At Mach numbers greater than 8.5, the thermal environment around the aft fuselage is a known unknown−a potential design and/or performance risk issue. The adverse effects of shock waves on the aft fuselage and plumeinduced flow separation are other potential risks. The development of an operational reusable launcher from the Skylon concept necessitates the judicious use of a combination of engineering methods, advanced methods based on required physics or analytical fidelity, test data, and independent assessments.

Mehta, Unmeel↗

NASA NTRS1983

Sound radiation from annular ducts/nozzles using modal decomposition of in-duct acoustic power

Using a refined acoustic impulse technique, an experimental program was carried out to determine the proper procedure for measuring the acoustic power for both incident and reflected sound fields for annular ducts with and without nozzles at various flow conditions. Several radial and azimuthal pressure measurements were made, and using these complex pressure data, the modal content of the pressure field was determined. A mathematical approach for the modal decomposition of annular duct acoustic power was developed. The acoustic power due to each individual mode and also their total sum were derived. The acoustic characteristics of annular duct-nozzle systems were studied at various flow conditions. The results derived from the experiments include the termination reflection coefficient, the normalized transmission coefficients, the power transfer functions and the power imbalance.

Salikuddin, M.↗