Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pitch control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Static Longitudinal Stability and Control Characteristics At A Mach Number of 1.99 of a Lenticular-Shaped Reentry Vehicle

An investigation has been made in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.99 to determine the longitudinal stability and control characteristics of a reentry model consisting of a lenticular-shaped body with two fin configurations (horizontal fins with end plates). Effects of deflecting the larger size fins as pitch-control surfaces were also investigated. The results indicate that the body alone was unstable from an angle of attack of 0 deg to about 55 deg where it became stable and remained so to 90 deg. The addition of fins provided positive longitudinal stability throughout the angle-of-attack range and increased the lift-drag ratio of the configuration. Reducing the horizontal-fin area at the inboard trailing edge of the fin had only a small effect on the aerodynamic characteristics of the vehicle for the condition of no fin deflection. Deflecting the fins, appeared to be an effective means of pitch control and had only a small effect on lift-drag ratio.

Jackson, Charles M., Jr.↗
NASA NTRS1991

Initial piloted simulation study of geared flap control for tilt-wing V/STOL aircraft

A simulation study of a representative tilt wing transport aircraft was conducted in 1990 on the Ames Vertical Motion Simulator. This simulation is in response to renewed interest in the tilt wing concept for use in future military and civil applications. For past tilt wing concepts, pitch control in hover and low-speed flight has required a tail rotor or reaction jets at the tail. Use of mono cyclic propellers or a geared flap have also been proposed as alternate methods for providing pitch control at low speed. The geared flap is a subject of this current study. This report describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, the pilots' evaluation tasks and procedures, and the results obtained from the simulation experiment. The pilot evaluations and comments are also documented in the report appendix.

Guerrero, Lourdes M.↗
NASA NTRS1984

An advanced pitch change mechanism incorporating a hybrid traction drive

A design of a propeller pitch control mechanism is described that meets the demanding requirements of a high-power, advanced turboprop. In this application, blade twisting moment torque can be comparable to that of the main reduction gearbox output: precise pitch control, reliability and compactness are all at a premium. A key element in the design is a compact, high-ratio hybrid traction drive which offers low torque ripple and high torsional stiffness. The traction drive couples a high speed electric motor/alternator unit to a ball screw that actuates the blade control links. The technical merits of this arrangement and the performance characteristics of the traction drive are discussed.

Steinetz, B. M.↗
NASA NTRS1971

Improved ITOS attitude control system with Hall generator brushless motor and earth-splitting technique

The ITOS with an improved attitude control system is described. A Hall generator brushless dc torque motor will replace the brush dc torque motor on ITOS-I and ITOS-A (NOAA-1). The four attitude horizon sensors will be replaced with two CO2 sensors for better horizon definition. An earth horizon splitting technique will be used to keep the earth facing side of the satellite toward earth even if the desired circular orbit is not achieved. The external appearance of the pitch control subsystem differs from TIROS-M (ITOS-1) and ITOS-A (NOAA-1) in that two instead of one pitch control electronics (PCE) boxes are used. Two instead of four horizon sensors will be used and one instead of two mirrors will be used for sensor scanning. The brushless motor will eliminate the requirement for brushes, strain gages and the telemetry for the brush wear. A single rotating flywheel, supported by a single bearing provides the gyroscopic stability and the required momentum interchange to keep one side of the satellite facing the earth. Magnetic torquing against the earth's magnetic field eliminates the requirement for expendable propellants which would limit satellite life in orbit.

Peacock, W. M.↗
NASA NTRS1995

Comparative wind tunnel tests of NACA 23024 airfoils with several aileron and spoiler configurations

This paper reviews research efforts at Wichita State University sponsored by NASA Lewis Research Center to design and evaluate aerodynamic braking devices which will be smaller and lighter than full-chord blade pitch control. Devices evaluated include a variety of aileron configurations, and spoilers located at both trailing edge and near the leading edge. The paper discusses analytical modeling, wind tunnel tests, and for some configurations, full-scale rotor tests. Current designs have not provided adequate control power at high angles of attack (low tip-speed-ratios). The reasons for these limitations are discussed. Analysis and wind tunnel test data indicate that several options are available to the designer to provide aerodynamic slowdown without full-chord pitch control. Three options are suggested; adding venting in front of the control surface hingeline, using spoilers located near the leading edge, and using a two-piece control combining downward deflection inboard with upward deflection outboard.

Wentz, W. H., Jr.↗
NASA NTRS1972

In-flight pilot evaluations of the flying qualities of a four-engine jet transport

The flying qualities of the CV-990 jet transport were evaluated over the normal operating flight envelope and in smooth air to provide baseline data for transport airplanes. Pilot ratings of airplane handling characteristics for specific test conditions and configurations from approach to normal cruise were compared with various flying qualities criteria. In general, the CV-990 flying qualities were evaluated as satisfactory, and the evaluations supported transport flying qualities criteria. The Dutch roll damping was rated more satisfactory than was predicted by the flying qualities criteria. The pilots found rudder coordination for the yaw generated during high roll rates very difficult. They preferred to control with roll and pitch controls and to use the yaw damper to provide the required rudder coordination.

Holleman, E. C.↗
NASA NTRS1977

A review of advanced rotor research

This paper reviews advanced-rotor concepts including the advancing blade concept, the circulation control rotor, the X-wing rotor, the variable diameter rotor, the hingeless tilt rotor, the bearingless main rotor, the composite structures rotor, the variable geometry rotor, the multicyclic controllable pitch rotor, the multicyclic controllable twist rotor, and the live twist rotor. The rotor concepts are discussed in terms of performance (cruise speed, and lift/drag ratio) and dynamic loads and vibration.

Kelly, M. W.↗
NASA NTRS1980

Multicyclic control for helicopters - Research in progress at Ames Research Center

The term multicyclic control describes a blade pitch control technique used by helicopter designers to alleviate vibration in rotorcraft. Because rotor-induced vibrations are periodic, a multicyclic system, synchronized to the main rotor's azimuth position, is suitable. Many types of rotors - ranging from the jet-flap and circulation-control rotors to the conventional full-blade feathering rotors - have utilized multicyclic control. Multicyclic control systems may be designed to reduce blade-bending stresses, to reduce rotor-induced vibration, and to improve rotor performance. Rotor types are reviewed, primarily to highlight their differences. The increased use of composites in blade construction is seen to indicate that vibration alleviation will be the prime focus of multicyclic control. Adaptive feedback control systems, which also incorporate gust alleviation, are considered to be the ultimate application of multicyclic control.

Mccloud, J. L., III↗
NASA NTRS1984

Development of an advanced pitch active control system for a wide body jet aircraft

An advanced PACS control law was developed for a commercial wide-body transport (Lockheed L-1011) by using modern control theory. Validity of the control law was demonstrated by piloted flight simulation tests on the NASA Langley visual motion simulator. The PACS design objective was to develop a PACS that would provide good flying qualities to negative 10 percent static stability margins that were equivalent to those of the baseline aircraft at a 15 percent static stability margin which is normal for the L-1011. Also, the PACS was to compensate for high-Mach/high-g instabilities that degrade flying qualities during upset recoveries and maneuvers. The piloted flight simulation tests showed that the PACS met the design objectives. The simulation demonstrated good flying qualities to negative 20 percent static stability margins for hold, cruise and high-speed flight conditions. Analysis and wind tunnel tests performed on other Lockheed programs indicate that the PACS could be used on an advanced transport configuration to provide a 4 percent fuel savings which results from reduced trim drag by flying at negative static stability margins.

Guinn, Wiley A.↗
NASA NTRS1987

Piloted simulator study of allowable time delay in pitch flight control system of a transport airplane with negative static stability

A piloted simulation study was conducted to determine the permissible time delay in the flight control system of a 10-percent statically unstable transport airplane during cruise flight conditions. The math model used for the simulation was a derivative Lockheed L-1011 wide-body jet transport. Data were collected and analyzed from a total of 137 cruising flights in both calm- and turbulent-air conditions. Results of this piloted simulation study verify previous findings that show present military specifications for allowable control-system time delay may be too stringent when applied to transport-size airplanes. Also, the degree of handling-qualities degradation due to time delay is shown to be strongly dependent on the source of the time delay in an advanced flight control system. Maximum allowable time delay for each source of time delay in the control system, in addition to a less stringent overall maximum level of time delay, should be considered for large aircraft. Preliminary results also suggest that adverse effects of control-system time delay may be at least partially offset by variations in control gearing. It is recommended that the data base include different airplane baselines, control systems, and piloting tasks with many pilots participating, so that a reasonable set of limits for control-system time delay can be established to replace the military specification limits currently being used.

Grantham, William D.↗
NASA NTRS1990

The FX/90: A proposal in response to a low Reynolds Number station keeping mission

The FX/90 is a remotely piloted vehicle designed to fly at Reynolds numbers below 2 x 10 to the 5th power. Several applications exist for this type of flight, such as low altitude flight of very small aircraft. The design presented here allows investigation into the unique problems involved in low Reynolds number flight, which will, in turn, further understanding of this flight regime. The aircraft will operate in a steady flight environment, free from significant atmospheric turbulence and weather effects. The F-90 has a 39 in. fuselage which is constructed of balsa and plywood. The landing gear for the aircraft is a detachable carriage on which the aircraft rests. The aerodynamic planform is a rectangular wing (no taper or sweep) with a chord of 9 in., a wingspan of 72 in., and is constructed entirely out of styrofoam. The propulsion system is a puller configuration mounted on the front of the fuselage. It consists of an Astro 05 engine and a 10-6 two bladed propeller. Control of the aircraft is accomplished through the use of two movable control surfaces: elevators for pitch control, and a rudder for yaw control. The aircraft is soundly constructed, highly maneuverable, and adequately powered. Furthermore, the investigation into alternative technologies, most notably the styrofoam wing and the detachable landing gear, holds promise to improve the performance of the aircraft.

Wirthman, David↗
NASA NTRS1992

On a finite-state inflow application to flap-lag-torsion damping in hover

An aerodynamic model with a coupled set of generalized dynamic wake equations and hybrid equations of motion for an elastic blade are applied here to a two-blade untwisted stiff in-plane hingeless small-scale model rotor with torsionally soft blades. Blade root offset, precone, blade droop, pitch control stiffness, and blade pitch angle are included in the model rotor. Numerical results show that 3D tip relief effects within the nonuniform steady-state inflow are significant to predict steady-state aerodynamic loads and blade deflections. Eigenvalue results confirm the importance of unsteady 3D aerodynamics in predicting lead-lag damping and frequency. Eigenvector analysis correlations reinforced qualitative and quantitative shortcomings associated with quasi-steady 2D aerodynamic theory for aeroelastic applications in hover.

De Andrade, Donizeti↗
NASA NTRS1982

Method and apparatus for producing an aircraft flare path control signal

Aircraft altitude, ground velocity, and altitude rate signals are input to a computer which, using a unique control law, generates a pitch control surface command signal suitable for guiding an aircraft on its flare path to a specified runway touchdown point despite varying wind conditions.

Lambregts, Antonius A.↗
NASA NTRS1949

Hovering and Low-Speed Performance and Control Characteristics of the Kaman Helicopter Rotor System as Determined on the Langley Helicopter Tower. TED No. NACA DE 205

An investigation has been conducted with the Langley helicopter tower to obtain basic performance and control characteristics of the Raman rotor system. Blade-pitch control is obtained in this configuration by utilizing an auxiliary flap to twist the blades. Rotor thrust and power required were measured for the hovering condition and over a range of wind velocities from 0 to 30 miles per hour. The control characteristics and the transient response of the rotor to various control movements were also measured. The hovering-performance data are presented as a survey of the wake velocities and the variation of torque coefficient with thrust coefficient. The power required for the test rotor to hover at a thrust of 1350 pounds and a rotor speed of 240 rpm is approximately 6.5 percent greater than that estimated for a conventional rotor of the same diameter and solidity. It is believed that most of this difference is caused by th e flap servomechanism. The reduction in total power required for sustentation of the single-rotor configuration tested at various wind velocities and at the normal operating rotor thrust was found to be similar to the theoretical and experimental results for ro tors with conventionally actuated pitch. The control effectiveness was determined as a function of rotor speed. Sufficient control was available to give a thrust range of 0 to 1500 pounds and a rotor tilt of plus or minus 7 degrees. The time lag between flap motion and blade-pitch response is approximately 0.02 to 0.03 second. The response of the rotor following the blade-pitch response is similar to that of a rotor with conventionally actuated pitch changes. The over-all characteristics of the rotor investigated indicate that satisfactory performance and control characteristics were obtained.

Carpenter, Paul J.↗
NASA NTRS1957

Flight Tests of a Model of a High-wing Transport Vertical-take-off Airplane with Tilting Wing and Propellers and with Jet Controls at the Rear of the Fuselage for Pitch and Yaw Control

An investigation of the stability and control of a high-wing transport vertical-take-off airplane with four engines during constant-altitude transitions from hovering to normal forward flight was conducted with a remotely controlled free-flight model. The model had four propellers distributed along the wing with the thrust axes in the wing chord plane. The wing could be rotated to 90 degrees incidence so that the propeller thrust axes were vertical for hovering flight. An air jet at the rear of the fuselage provided pitch and yaw control for hovering and low-speed flight.

CONTROL, LONGITUDINAL↗