Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parameter reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Flight tests for the assessment of task performance and control activity

The tests were performed with the helicopters BO 105 and UH-1D. Closely connected with tactical demands the six test pilots' task was to minimize the time and the altitude over the obstacles. The data reduction yields statistical evaluation parameters describing the control activity of the pilots and the achieved task performance. The results are shown in form of evaluation diagrams. Additionally dolphin tests with varied control strategy were performed to get more insight into the influence of control techniques. From these test results recommendations can be derived to emphasize the direct force control and to reduce the collective to pitch crosscoupling for the dolphin.

Pausder, H. J.↗
NASA NTRS1984

Enhanced vibration controllability by minor structural modifications

A procedure for checking whether small changes in a structure have the potential for significant enhancements of its vibration control system is described. The first step in the procedure consists of the calculation of the sensitivity of the required strength of the control system to small changes in structural parameters. The second step consists of the optimization of the structural parameters to produce maximal reduction in required control system strength with minimal change in the structure. The procedure has been demonstrated for a flexible beam supported by four cables and controlled by a rate feedback single-colocated force-actuator velocity-sensor pair. Large changes in control strength requirement were obtained with small structural modifications. Analytical predictions of such effects have also been validated experimentally.

Haftka, R. T.↗
NASA NTRS1989

Middle atmosphere measurements of small-scale electron density irregularities and ion properties during the MAC/Epsilon campaign

Rocket payloads designed to measure small scale electron density irregularities and ion properties in the middle atmosphere were flown with each of the three main salvos of the MAC/Epsilon campaign conducted at the Andoya Rocket Range, Norway, during October to November 1987. Fixed bias, hemispheric nose tip probes measured small scale electron density irregularities, indicative of neutral air turbulence, during the rocket's ascent; and subsequently, parachute-borne Gerdien condensers measured the region's polar electrical conductivity, ion mobility and density. One rocket was launched during daylight (October 15, 1052:20 UT), and the other two launches occurred at night (October 21, 2134 UT: November 12, 0021:40 UT) under moderately disturbed conditions which enhanced the detection and measurement of turbulence structures. A preliminary analysis of the real time data displays indicates the presence of small scale electron density irregularities in the altitude range of 60 to 90 km. Ongoing data reduction will determine turbulence parameters and also the region's electrical properties below 90 km.

Blood, S. P.↗
NASA NTRS1991

The 15 years of comet photometry: A comparative analysis of 80 comets

In 1976, a program of narrowband photometry of comets was initiated that has encompassed well over 400 nights of observations. To date, the program has provided detailed information on 80 comets, 11 of which were observed during multiple apparitions. The filters (initially isolating CN, C2, and continuum and later including C3, OH, and NH) as well as the detectors used for the observations were changed over time, and the parameters adopted in the reduction and modeling of the data have likewise evolved. Accordingly, we have re-reduced the entire database and have derived production rates using current values for scalelengths and fluorescence efficiencies. Having completed this task, the results for different comets can now be meaningfully compared. The general characteristics that are discussed include ranges in composition (molecular production rate ratios) and dustiness (gas production compared with Af(rho)). Additionally an analysis of trends on how the production rates vary with heliocentric distance and on pre- and post-perihelion asymmetries in the production rates of individual comets. Possible taxonomic groupings are also described.

Osip, David J.↗
NASA NTRS1990

Lead-ruthenium pyrochlores as oxygen electrocatalysts

An investigation of lead-ruthenium pyrochlores of the structure Pb2(Ru/2-x/Pb/x/) O7-y for use as oxygen electrocatalysts in alkaline media is discussed. Lead-ruthenium pyrochlore mixed metal oxides were prepared and characterized by X-ray diffraction, BET surface area, dry powder conductivity, and chemical stability. Gas diffusion electrodes were developed specifically for the lead-ruthenium pyrochlore materials. Also investigated were the effects of varying electrode fabrication parameters on the oxygen reduction performance of the lead-ruthenium pyrochlore electrocatalyst. Long-term stability performance was also evaluated. The oxygen reduction performance of the pyrochlore electrocatalyst is considerably higher than that of the state-of-the-art gold-platinum alloy electrocatalyst currently used by NASA. Furthermore, the pyrochlore electrocatalysts are attractive candidates for high-performance pressurized alkaline fuel cells.

Anderson, E. B.↗
NASA NTRS1996

Multigrid Approach to Incompressible Viscous Cavity Flows

Two-dimensional incompressible viscous driven-cavity flows are computed for Reynolds numbers on the range 100-20,000 using a loosely coupled, implicit, second-order centrally-different scheme. Mesh sequencing and three-level V-cycle multigrid error smoothing are incorporated into the symmetric Gauss-Seidel time-integration algorithm. Parametrics on the numerical parameters are performed, achieving reductions in solution times by more than 60 percent with the full multigrid approach. Details of the circulation patterns are investigated in cavities of 2-to-1, 1-to-1, and 1-to-2 depth to width ratios.

Wood, William A.↗
NASA NTRS1994

Acquisition and processing of data for isotope-ratio-monitoring mass spectrometry

Methods are described for continuous monitoring of signals required for precise analyses of 13C, 18O, and 15N in gas streams containing varying quantities of CO2 and N2. The quantitative resolution (i.e. maximum performance in the absence of random errors) of these methods is adequate for determination of isotope ratios with an uncertainty of one part in 10(5); the precision actually obtained is often better than one part in 10(4). This report describes data-processing operations including definition of beginning and ending points of chromatographic peaks and quantitation of background levels, allowance for effects of chromatographic separation of isotopically substituted species, integration of signals related to specific masses, correction for effects of mass discrimination, recognition of drifts in mass spectrometer performance, and calculation of isotopic delta values. Characteristics of a system allowing off-line revision of parameters used in data reduction are described and an algorithm for identification of background levels in complex chromatograms is outlined. Effects of imperfect chromatographic resolution are demonstrated and discussed and an approach to deconvolution of signals from coeluting substances described.

NASA Discipline Exobiology↗
NASA NTRS2008

James Webb Space Telescope - Applying Lessons Learned to I&T

The James Webb Space Telescope (JWST) is part of a new generation of spacecraft acquiring large data volumes from remote regions in space. To support a mission such as the JWST, it is imperative that lessons learned from the development of previous missions such as the Hubble Space Telescope and the Earth Observing System mission set be applied throughout the development and operational lifecycles. One example of a key lesson that should be applied is that core components, such as the command and telemetry system and the project database, should be developed early, used throughout development and testing, and evolved into the operational system. The purpose of applying lessons learned is to reap benefits in programmatic or technical parameters such as risk reduction, end product quality, cost efficiency, and schedule optimization. In the cited example, the early development and use of the operational command and telemetry system as well as the establishment of the intended operational database will allow these components to be used by the developers of various spacecraft components such that development, testing, and operations will all use the same core components. This will reduce risk through the elimination of transitions between development and operational components and improve end product quality by extending the verification of those components through continual use. This paper will discuss key lessons learned that have been or are being applied to the JWST Ground Segment integration and test program.

Johns, Alan↗
NASA NTRS1976

Determination of nonlinear energy toughness values for cyclic loading applications

For several years the nonlinear energy method proposed by Liebowitz and Eftis has been examined as a failure criterion for static testing of center-cracked and compact tension specimens. Since the method appears to be valid under conditions of crack-tip plasticity, subcritical crack growth and load relaxation, tests have been conducted to ascertain the merit of this method as a failure criterion under cyclic loading conditions. The nonlinear energy toughness for cyclic loading is obtained from an envelope of the cyclic load-displacement record, which naturally imposes some restrictions on the loading program. The cyclic toughness parameter has been evaluated for thin center-cracked sheets of 2024-T3 and 7075-T6 aluminum alloys. Both alloys exhibited a significant reduction of the cyclic toughness parameter with increasing cyclic life in a manner similar to the classical S-N diagram. It is suggested that this method may serve the design process by allowing the establishment of a fracture toughness parameter capable of including the effects of the entire loading history of a structure into the fracture toughness requirements.

Poulose, P. K.↗
NASA NTRS2006

Latitudinal variations of cloud base height and lightning parameters in the tropics

The observed reduction in cloud-to-ground lightning in the new-equational zone is examined from the perspective of the width of the main negative charge region. Thermodynamic observations of cloud base height also show a climatological minimum value in the near-equatorial region. The association of low cloud base with both narrow updrafts and narrow changing zones may impede the bridging of the large air gap to ground, and thereby suppress cloud-to-ground lightning activity. This width dependence may be more important than the approx. 10% variation in height of the freezing level in the encouraging flashes to ground.

Mushtak, V. C.↗
NASA NTRS2008

Prediction of Turbulent Jet Mixing Noise Reduction by Water Injection

A one-dimensional control volume formulation is developed for the determination of jet mixing noise reduction due to water injection. The analysis starts from the conservation of mass, momentum and energy for the confrol volume, and introduces the concept of effective jet parameters (jet temperature, jet velocity and jet Mach number). It is shown that the water to jet mass flow rate ratio is an important parameter characterizing the jet noise reduction on account of gas-to-droplet momentum and heat transfer. Two independent dimensionless invariant groups are postulated, and provide the necessary relations for the droplet size and droplet Reynolds number. Results are presented illustrating the effect of mass flow rate ratio on the jet mixing noise reduction for a range of jet Mach number and jet Reynolds number. Predictions from the model show satisfactory comparison with available test data on perfectly expanded hot supersonic jets. The results suggest that significant noise reductions can be achieved at increased flow rate ratios.

Kandula, Max↗
NASA NTRS2007

Effective Jet Properties for the Prediction of Turbulent Mixing Noise Reduction by Water Injection

A one-dimensional control volume formulation is developed for the determination of jet mixing noise reduction due to water injection. The analysis starts from the conservation of mass, momentum and energy for the control volume, and introduces the concept of effective jet parameters (jet temperature, jet velocity and jet Mach number). It is shown that the water to jet mass flow rate ratio is an important parameter characterizing the jet noise reduction on account of gas-to-droplet momentum and heat transfer. Two independent dimensionless invariant groups are postulated, and provide the necessary relations for the droplet size and droplet Reynolds number. Results are presented illustrating the effect of mass flow rate ratio on the jet mixing noise reduction for a range of jet Mach number and jet Reynolds number. Predictions from the model show satisfactory comparison with available test data on supersonic jets. The results suggest that significant noise reductions can be achieved at increased flow rate ratios.

Kandula, Max↗
NASA NTRS2002

Studies of Dust Emission as Measured by DIRBE and IRAS

The main activity supported by this grant was to make the dust reddening map more useful for optical and microwave astronomy, and to increase our understanding of interstellar dust in general. We completed all the major objectives of the proposal, and we are eagerly awaiting the launch of Space Infrared Telescope Facility (SIRTF) so that we can check one of our most controversial conclusions. According to the ADS abstract service, the above paper has been cited 895 times. A number of authors have claimed the SFD98 dust maps are miscalibrated, but recent work suggests that the calibration is correct. The primary goal of this ADP grant was to determine the microwave / sum-mm spectrum of interstellar dust emission by cross-correlating the Far Infrared Absolute Spectrophotometer (FIRAS) spectra with a model based on the SFD98 dust map. Because of temperature variation, large (factor of two) variations are observed in submillimeter / 100 micron ratio, so a careful accounting of dust temperature data, based on Diffuse Infrared Background Experiment (DIRBE) 100 and 240 micron channels, was required. Even this improvement was unable to reduce the chi(sup 2) per degree of freedom below 30. Further study revealed that a two-component model, with the two components having different (but reasonable) optical properties, achieved a decrease in chi(sup 2) to less than 2, five times better than the next best fit in the literature. The resulting model uses density and temperature estimates based on DIRBE data, with only four global parameters fit using the FIRAS data. This dramatic reduction in chi(sup 2) using only four fit parameters may indicate that the model is physically correct, but in any case, it is an acceptable phenomenological model. We have released the appropriate data and software on our website (http://astro.berkeley.edu/dust) to allow users to compute the interstellar dust emission between from 100-3000 GHz (or 100 micron 3 mm) with approx. 15% precision. The paper describing these efforts appeared in ApJ 524, 867. This paper has to date been cited 24 times.

Davis, Marc↗
NASA NTRS1992

Krylov vector methods for model reduction and control of flexible structures

Krylov vectors and the concept of parameter matching are combined here to develop model-reduction algorithms for structural dynamics systems. The method is derived for a structural dynamics system described by a second-order matrix differential equation. The reduced models are shown to have a promising application in the control of flexible structures. It can eliminate control and observation spillovers while requiring only the dynamic spillover terms to be considered. A model-order reduction example and a flexible structure control example are provided to show the efficacy of the method.

Su, Tzu-Jeng↗
NASA NTRS1979

Preliminary noise tradeoff study of a Mach 2.7 cruise aircraft

NASA computer codes in the areas of preliminary sizing and enroute performance, takeoff and landing performance, aircraft noise prediction, and economics were used in a preliminary noise tradeoff study for a Mach 2.7 design supersonic cruise concept. Aerodynamic configuration data were based on wind-tunnel model tests and related analyses. Aircraft structural characteristics and weight were based on advanced structural design methodologies, assuming conventional titanium technology. The most advanced noise prediction techniques available were used, and aircraft operating costs were estimated using accepted industry methods. The 4-engines cycles included in the study were based on assumed 1985 technology levels. Propulsion data was provided by aircraft manufacturers. Additional empirical data is needed to define both noise reduction features and other operating characteristics of all engine cycles under study. Data on VCE design parameters, coannular nozzle inverted flow noise reduction and advanced mechanical suppressors are urgently needed to reduce the present uncertainties in studies of this type.

Mascitti, V. R.↗
NASA NTRS1988

Basic research for the geodynamics program

Additional results are presented concerning a study that considers improvements over present Earth Rotation Parameter (ERP) determination methods by directly combining observations from various space geodetic systems in one adjustment. Earlier results are extended, showing that in addition to slight improvements in accuracy, substantial (a factor of three or more) improvements in precision and significant reductions in correlations between various parameters can be obtained (by combining Lunar Laser Ranging - LLR, Satellite Laser Ranging - SLR to Lageos, and Very Long Baseline Interferometry - VLBI data in one adjustment) as compared to results from individual systems. Smaller improvements are also seen over the weighted means of the individual system results. Although data transmission would not be significantly reduced, negligible additional computer time would be required if (standardized) normal equations were available from individual solutions. Suggestions for future work and implications for the New Earth Rotation Service (IERS) are also presented.

Mueller, Ivan I.↗
NASA NTRS1992

Development of an expert data reduction assistant

We propose the development of an expert system tool for the management and reduction of complex data sets. The proposed work is an extension of a successful prototype system for the calibration of CCD images developed by Dr. Johnston in 1987. The reduction of complex multi-parameter data sets presents severe challenges to a scientist. Not only must a particular data analysis system be mastered, (e.g. IRAF/SDAS/MIDAS), large amounts of data can require many days of tedious work and supervision by the scientist for even the most straightforward reductions. The proposed Expert Data Reduction Assistant will help the scientist overcome these obstacles by developing a reduction plan based on the data at hand and producing a script for the reduction of the data in a target common language.

Miller, Glenn E.↗