Results for “observable behavior” — Page 5

NASA NTRS1984

A history dependent damage model for low cycle fatigue

This paper examines damage assessment and accumulation. A nonlinear damage postulate is advanced that embodies the dependence of the damage rate on cycle-dependent changes in the bulk microstructure and the surface topography. The postulate is analytically formulated in terms of the deformation history dependence of the bulk behavior. This formulation is used in conjunction with baseline data in accordance with the damage postulate to predict the low cycle fatigue resistance of OFE copper. Close comparison of the predictions with observed behavior suggests the postulate offers a viable basis for nonlinear damage analysis.

Leis, B. N.↗

NASA NTRS2002

Atomistic Modeling of Quaternary Alloys: Ti and Cu in NiAl

The change in site preference in NiAl(Ti,Cu) alloys with concentration is examined experimentally via ALCHEMI and theoretically using the Bozzolo-Ferrante-Smith (BFS) method for alloys. Results for the site occupancy of Ti and Cu additions as a function of concentration are determined experimentally for five alloys. These results are reproduced with large-scale BFS-based Monte Carlo atomistic simulations. The original set of five alloys is extended to 25 concentrations, which are modeled by means of the BFS method for alloys, showing in more detail the compositional range over which major changes in behavior occur. A simple but powerful approach based on the definition of atomic local environments also is introduced to describe energetically the interactions between the various elements and therefore to explain the observed behavior.

Bozzolo, Guillermo↗

NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Ice Crystal Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for the development of icing physics models and simulation validation. This paper presents the analysis of the ice crystal icing data subset from tests conducted in 2022 at the NASA Icing Research Tunnel that studied both supercooled liquid and ice-crystal icing. The test article that was utilized replicated 3D geometrical features of an inter-compressor duct and strut region of a turbofan engine. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a weighing scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized icing conditions. To that end, ice crystal cloud characterization tests were conducted that provided cloud property values at the test section. The ice crystal accretion tests investigated how different test condition parameters impacted ice accretion size, location, and characteristics (such as physical attributes). A key finding was that a sufficiently high surface heat flux at the leading edge can provide a continuous supply of liquid melt to critical accretion zones downstream, resulting in elevated ice mass accretions. Another key finding was that warmer heater settings in critical accretion zones can suppress ice accretion. These findings are consistent with icing behavior observed in full-scale engine icing tests conducted previously at the NASA Glenn Research Center. Test runs investigating the contribution of liquid melt generated at the leading edge found that the melt can be transported downstream to critical accretion regions in two forms, via runback and splash. The form of melt supplied downstream affected accretion behavior and features. Sharkteeth-shaped ice accretions were generated at certain test conditions, a physical attribute that has been observed in full-scale engine icing tests. The ice accretion data will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost‑effective way.

ice crystal icing↗

NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Ice Crystal Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for the development of icing physics models and simulation validation. This paper presents the analysis of the ice crystal icing data subset from tests conducted in 2022 at the NASA Icing Research Tunnel that studied both supercooled liquid and ice-crystal icing. The test article that was utilized replicated 3D geometrical features of an inter-compressor duct and strut region of a turbofan engine. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a weighing scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized icing conditions. To that end, ice crystal cloud characterization tests were conducted that provided cloud property values at the test section. The ice crystal accretion tests investigated how different test condition parameters impacted ice accretion size, location, and characteristics (such as physical attributes). A key finding was that a sufficiently high surface heat flux at the leading edge can provide a continuous supply of liquid melt to critical accretion zones downstream, resulting in elevated ice mass accretions. Another key finding was that warmer heater settings in critical accretion zones can suppress ice accretion. These findings are consistent with icing behavior observed in full-scale engine icing tests conducted previously at the NASA Glenn Research Center. Test runs investigating the contribution of liquid melt generated at the leading edge found that the melt can be transported downstream to critical accretion regions in two forms, via runback and splash. The form of melt supplied downstream affected accretion behavior and features. Sharkteeth-shaped ice accretions were generated at certain test conditions, a physical attribute that has been observed in full-scale engine icing tests. The ice accretion data will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost‑effective way.

ice crystal icing↗

NASA NTRS1988

A nonlinear history-dependent damage model for low cycle fatigue

A nonlinear damage postulate that embodies the dependence of the damage rate on cycle-dependent changes in the bulk microstructure and the surface topography is examined. The postulate is analytically formulated in terms of the deformation history dependence of the bulk behavior. This formulation is used in conjunction with baseline data in accordance with the damage postulate to predict the low cycle fatigue resistance of OFE copper. Close comparison of the predictions with experimentally observed behavior suggests that the postulate offers a viable basis for nonlinear damage analysis.

Leis, B. N.↗

NASA NTRS1998

Effects of Gravity on Crystallization of Fluorozircante Optical Fibers

ZBLAN (ZrF4-BaF2-LaF3-AlF3-NaF) optical fibers were flown on NASA's reduced gravity KC135 aircraft and Conquest I sub-orbital rocket. The purpose of these experiments was to determine the effects of gravity on the crystallization process of this material. Fiber samples encapsulated in evacuated quartz ampoules were heated to the crystallization temperature during flight in reduced gravity and on the ground in unit gravity. Scanning electron and transmission electron microscopy were utilized to study the crystallization behavior. Samples heated under unit gravity conditions exhibited significant crystallization, while fibers heated to the crystallization temperature in reduced gravity showed no signs of crystallization. A mechanism based on microcellular convection is proposed to explain these observed behaviors.

Tucker, D. S.↗

NASA NTRS1991

Observation of frequency doubling in tantalum doped silica fibres

Second harmonic conversion efficients of 3 x 0,0001 in tantalum-doped silica fibers prepared by the seeding technique are reported. A series of experiments were conducted to characterize the frequency doubling in this fiber and to compare the results to the behavior observed in germanosilicate and rare earth-doped aluminosilicate fibers.

Driscoll, T. J.↗

NASA NTRSDate not supplied

Electromagnetic Modeling of Wind tunnel Magnetic Suspension and Balance Systems

An analytical framework for the open-loop behavior of a permanent magnet element levitated within an applied magnetic field are shown, in the context of application to wind tunnel Magnetic Suspension and Balance Systems (MSBS). Various modes of motion are identified, which correlate with observed behavior of the NASA/ODU 6-inch MSBS. This system is being developed as a technology demonstrator for dynamic stability testing of atmospheric entry capsules, with possible application to a supersonic wind tunnel. The analytic equations are populated with field information from experimental measurements and a finite element model. Finally, a system simulation can provide alternative estimates of system dynamic behavior via model linearization, with preliminary comparisons presented. Taken together, the analytical framework, experimental measurement, finite element analysis, and dynamic simulation provide a complete understanding of the characteristics and behavior of the MSBS.

magnetic suspension↗

NASA NTRS2016

Probabilistic Modeling of Aircraft Trajectories for Dynamic Separation Volumes

With a proliferation of new and unconventional vehicles and operations expected in the future, the ab initio airspace design will require new approaches to trajectory prediction for separation assurance and other air traffic management functions. This paper presents an approach to probabilistic modeling of the trajectory of an aircraft when its intent is unknown. The approach uses a set of feature functions to constrain a maximum entropy probability distribution based on a set of observed aircraft trajectories. This model can be used to sample new aircraft trajectories to form an ensemble reflecting the variability in an aircraft's intent. The model learning process ensures that the variability in this ensemble reflects the behavior observed in the original data set. Computational examples are presented.

Lewis, Timothy A.↗

NASA NTRS1987

The fading of R Coronae Borealis

Using the International Ultraviolet Explorer (IUE) low-resolution spectra were obtained of R CrB, the prototype of its class of variable stars, shortly after the beginning of its 1983-84 minimum and during its rise to maximum again. The behavior of the spectra during the rise to maximum is similar to the behavior of the spectra of RY Sgr during a similar phase in 1979-80. The extinction data have been analyzed using Mie theory and are consistent with the stellar photosphere being obscured by 20-nm glassy carbon particles. The observations during the decline to minimum show substantial spectral variations which cannot be explained in terms of simple continuum absorption. An interpretation of the observed behavior in terms of a model incorporating an occulting cloud and circumstellar emission is offered.

Holm, A. V.↗

NASA NTRS1994

NO2 column changes induced by volcanic eruptions

Nitrogen dioxide slant column amounts measured by ground-based remote sensing from Lauder, New Zealand (45 deg S) and Campbell Island (53 deg S) during the second half of 1991 and early 1992 show anomalously low values that are attributed to the effects of volcanic eruptions. It is believed that the eruptions of Mount Pinatubo in the Philippines in June 1991 and possibly Mount Hudson in Chile in August 1991 are responsible for the stratospheric changes, which first became apparent in July 1991. The effects in the spring of 1991 are manifested as a reduction in the retrieved NO2 column amounts from normal levels by 35 to 45 percent, and an accompanying increase in the overnight decay of NO2. The existence of an accurate long-term record of column NO2 from the Lauder site enables us to quantify departures from the normal seasonal behavior with some confidence. Simultaneous retrievals of column ozone agree well with Dobson measurements, confirming that only part of the NO2 changes can be attributed to a modification of the scattering geometry by volcanic aerosols. Other reasons for the observed behavior are explored, including the effects of stratospheric temperature increases resulting from the aerosol loading and the possible involvement of heterogeneous chemical processes.

Johnston, Paul V.↗

NASA NTRS1972

Interstellar propagation of galactic cosmic-ray nuclei 2 less than or equal to Z less than or equal to 8 in the energy range 10 to 1000 MeV per nucleon.

Analysis of the differential kinetic energy per nucleon spectra of galactic cosmic-ray He, Li, Be, B, C, N, and O with the University of Chicago cosmic-ray telescope on board the IMP-5 satellite in 1969-1970. The ratios He/(C + N + O) and (Li + Be + B)/(C + N + O) obtained from these spectra are found, within errors of about 20%, to be energy-independent over the energy range 10-1000 MeV per nucleon, and equal to about 15 and about 0.25, respectively. These results are compared with discrepancies existing among other measurements of these ratios, and with predictions of a class of steady-state models of cosmic-ray propagation which assume that Li, Be, and B are absent in cosmic-ray sources. The best fits for the present measurements are obtained for models with a source spectrum in the form of a power law in total energy per nucleon, but even these fits are outside the error limits at energies below 100 MeV per nucleon. In the context of the propagation models examined, it is concluded that the observed behavior of these ratios requires an additional mechanism operative at low energies. This mechanism may be adiabatic deceleration of cosmic rays in the solar wind. In order for this mechanism to be adiabatic deceleration, the deceleration in 1969 must have been such that particles observed at 10 to 20 MeV per nucleon had energies greater than 100 to 150 MeV per nucleon in the local interstellar space.

Mason, G. M.↗

NASA NTRS1994

Radiative acceleration in outflows from broad absorption line quasi-stellar objects. 2: Wind models

We investigate the dynamics of radiatively driven broad absorption-line (BAL) outflows in quasi-stellar objects (QSOs) by developing radial and time-independent numerical models. Two limits are explored. The first assumes that the absorbing matter is not forced to comove with the substrate, which provides pressure confinement. This assumption allows us to explore in detail a case in which the acceleration is entirely due to radiation pressure. Using the parameters inferred from observations, we find that under these conditions radiative acceleration (mainly due to resonance line scattering) can readily accelerate the flow to the observed velocities. An important feature of the noncoupled flow is that the line profiles tend to stay relatively flat throughout the velocity interval covered by the line. We discuss how relaxing the assumptions of radial symmetry and time independent may help to explain the structures observed in BALs. In the second class of models, the absorbing flow is assumed to be completely coupled to the substrate in which it is embedded. Aside from being more plausible physically, these models produce line profiles that trail off at higher velocities, a behavior observed in some BALs. We show that, even if the substrate is massless, we have to assume a starting radius very close to the inferred radius of the broad emission-line region (approximately 0.1 pc) in order to obtain a significant contribution from radiative acceleration, given a typical active galactic nucleus (AGN) spectrum. The reason is that the energy input needed to pressurize the substrate, allowing the flow to become supersonic and to retain a reasonable ionization equilibrium, at the same time contributes appreciably to the acceleration. A way to relax the small starting radius constraint is to use a softer ionizing spectrum.

Arav, Nahum↗

NASA NTRS2015

Aeroelastic Analysis of SUGAR Truss-Braced Wing Wind-Tunnel Model Using FUN3D and a Nonlinear Structural Model

Considerable attention has been given in recent years to the design of highly flexible aircraft. The results of numerous studies demonstrate the significant performance benefits of strut-braced wing (SBW) and trussbraced wing (TBW) configurations. Critical aspects of the TBW configuration are its larger aspect ratio, wing span and thinner wings. These aspects increase the importance of considering fluid/structure and control system coupling. This paper presents high-fidelity Navier-Stokes simulations of the dynamic response of the flexible Boeing Subsonic Ultra Green Aircraft Research (SUGAR) truss-braced wing wind-tunnel model. The latest version of the SUGAR TBW finite element model (FEM), v.20, is used in the present simulations. Limit cycle oscillations (LCOs) of the TBW wing/strut/nacelle are simulated at angle-of-attack (AoA) values of -1, 0 and +1 degree. The modal data derived from nonlinear static aeroelastic MSC.Nastran solutions are used at AoAs of -1 and +1 degrees. The LCO amplitude is observed to be dependent on AoA. LCO amplitudes at -1 degree are larger than those at +1 degree. The LCO amplitude at zero degrees is larger than either -1 or +1 degrees. These results correlate well with both wind-tunnel data and the behavior observed in previous studies using linear aerodynamics. The LCO onset at zero degrees AoA has also been computed using unloaded v.20 FEM modes. While the v.20 model increases the dynamic pressure at which LCO onset is observed, it is found that the LCO onset at and above Mach 0.82 is much different than that produced by an earlier version of the FEM, v. 19.

Bartels, Robert E.↗

NASA NTRS2017

Relationship Between Unusual High-Temperature Fatigue Crack Growth Threshold Behavior in Superalloys and Sudden Failure Mode Transitions

An investigation of high temperature cyclic fatigue crack growth (FCG) threshold behavior of two advanced nickel disk alloys was conducted. The focus of the study was the unusual crossover effect in the near-threshold region of these type of alloys where conditions which produce higher crack growth rates in the Paris regime, produce higher resistance to crack growth in the near threshold regime. It was shown that this crossover effect is associated with a sudden change in the fatigue failure mode from a predominant transgranular mode in the Paris regime to fully intergranular mode in the threshold fatigue crack growth region. This type of a sudden change in the fracture mechanisms has not been previously reported and is surprising considering that intergranular failure is typically associated with faster crack growth rates and not the slow FCG rates of the near-threshold regime. By characterizing this behavior as a function of test temperature, environment and cyclic frequency, it was determined that both the crossover effect and the onset of intergranular failure are caused by environmentally driven mechanisms which have not as yet been fully identified. A plausible explanation for the observed behavior is proposed.

Fatigue Crack Growth Thresholds; Grain boundary ox↗

NASA NTRS2017

Relationship Between Unusual High-Temperature Fatigue Crack Growth Threshold Behavior in Superalloys and Sudden Failure Mode Transitions

An investigation of high temperature cyclic fatigue crack growth (FCG) threshold behavior of two advanced nickel disk alloys was conducted. The focus of the study was the unusual crossover effect in the near-threshold region of these type of alloys where conditions which produce higher crack growth rates in the Paris regime, produce higher resistance to crack growth in the near threshold regime. It was shown that this crossover effect is associated with a sudden change in the fatigue failure mode from a predominant transgranular mode in the Paris regime to fully intergranular mode in the threshold fatigue crack growth region. This type of a sudden change in the fracture mechanisms has not been previously reported and is surprising considering that intergranular failure is typically associated with faster crack growth rates and not the slow FCG rates of the near-threshold regime. By characterizing this behavior as a function of test temperature, environment and cyclic frequency, it was determined that both the crossover effect and the onset of intergranular failure are caused by environmentally driven mechanisms which have not as yet been fully identified. A plausible explanation for the observed behavior is proposed.

Fatigue Crack Growth Thresholds; Grain boundary ox↗

NASA NTRS2001

Cloud Structure and Cloud-Radiation Interaction: From Smallest Observable Scales (Less than 10 m) to GCM Grid Scales (More than 100 km)

In this presentation we review the fractal nature of internal cloud structure from cm- to km-scales as captured by in-situ probes during long horizontal penetrations by aircraft. We uncover the non-Poissonian spatial distribution of cloud droplets at submeter scales and confirm scale-invariant behavior for large scales. Based on these structural characteristics, we generate simple fractal cloud models that reproduce statistical scaling properties of real clouds. These stochastic models represent a link between nonlinear science, in general, and cloud-radiation interaction, in particular. Next we run three-dimensional radiative transfer computations on these synthetic fractal clouds and compare the structure of the resulting radiation fields with the known structure of the cloud model and with satellite images of real clouds. The different behaviors observed for small and large-scale variabilities will be discussed in detail. We find that while the large-scale fluctuations of the resulting radiation fields resemble those in the original scale-invariant cloud structure, the radiation at small scales is much smoother than its cloud liquid water counterpart. This violates scale-invariance and produces a scale-break at 0.2-0.5 km that is clearly observed in high-resolution satellite data such as from Landsat. Finally, we show how radiative transfer Green function theory in the photon diffusion limit explains (and predicts) the above phenomena of "radiative smoothing."

Marshak, Alexander↗

NASA NTRSDate not supplied

Examining the Relationship between Self-Reported Workload and Resilient Performance in Airline Flight Crews

Workload has long been associated with human performance in aviation. High workload is typically viewed as a system design problem. The aim of this work was to find observable behaviors that guard cognitive resource margins; thus, improve handling of perturbations that arise. Twelve commercial airline flight crews participated in an experiment at NASA Langley Research Center. We explored workload data (NASA Task Load Index) self-reported after completing flight simulation scenarios to see how different individuals, using the same technologies, cope with challenging situations. A trained observer from the same airline as the study participants assessed performance. We differentiated a lower workload crew from a higher workload crew and analyzed their workload and performance. Results indicate that the workload may be a component of pilots’ resilient performance. Initial strategies that reduced workload were classified and these types of behaviors, if implemented correctly, might assist pilots in maintaining functional workload resource margins.

Michael Stewart↗