Results for “numeric profiling” — Page 5

DOE OSTI2025

Mapping Spatiotemporal Solvent Velocity from Measured Concentration Gradients in a Polarized Electrolyte

The electric-field induced motion of neutral species impedes the efficacy of electrochemical devices. By combining operando X-ray transmission measurements with continuum mechanics, we have developed a methodology for determining the velocity of neutral solvent molecules under an applied field. The X-ray transmission experiments were used to determine ion concentration profiles as a function of space and time in a polymer electrolyte. The unsteady state solvent mass balance equation was solved numerically with experimental concentration profiles to map spatiotemporal solvent velocities. We compare our experimentally derived results with predictions made with concentrated solution theory. We use the cation transference number as the only adjustable parameter to match experimental measurements of both concentration and solvent velocity. Our approach may be used to determine solvent velocity with any operando technique used to measure time-dependent ion concentration profiles.

Abdo, Emily E↗

NASA NTRS1979

An internal velocity study of the Rosette Nebula

Emission-line profiles of H-alpha were studied at about 700 points in the Rosette Nebula by using a multislit echelle spectrograph. Numerical analysis of the profiles indicates that variations in the line-of-sight velocity occur within the nebula, reaching about + or - 20 km/s in the inner regions. Evidence is presented that these highest velocities are more probably inward, favoring a model where the central cavity is due to a depletion resulting from rapid star formation

Fountain, W. F.↗

DOE OSTI2024

Numerical implications of including drifts in SOLPS-ITER simulations of EAST

The inclusion of drifts in plasma edge codes like SOLPS-ITER is required to match simulation data with experimental profiles. However, this remains numerically challenging. In this paper, the effect of some numerical factors on the final plasma solution is investigated. This study is performed on three EAST simulations in the upper single null configuration: an attached purely deuterium case, an attached case with limited Ne-seeding, and a detached Ne-seeded case. The effects of the anomalous conductivity and anomalous thermo-electric coefficient on the plasma potential are investigated. Next, the effect of the employed grids is shown. In order to investigate these effects, accurate drift simulations are needed. Therefore, the employed time step and numerical parameters are discussed for the three studied simulations. For all presented simulations, it is verified that the restriction of the grid to the first flux surface tangent to the main chamber wall is sufficient within the context of non-extended simulations. This means that the main power dissipation takes place inside the simulated domain, and only a small fraction of the power is leaving the B2.5 grid through the grid boundary closest to the first wall. Finally, the effect of drifts on the asymmetry between the inner and outer target for EAST simulations is demonstrated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2016

Airborne Observations of Ozone and Other Trace Gases Upwind of National Parks in California and Nevada

The Alpha Jet Atmospheric eXperiment (AJAX) is a research project based at Moffett Field, CA, which collects airborne measurements of ozone, carbon dioxide, methane, water vapor, and formaldehyde, as well as 3-D winds, temperature, pressure, and location. Since its first science flight in 2011, AJAX has developed a wide a variety of mission types, combining vertical profiles (from approximately 8 km to near surface), boundary layer legs, and plume sampling as needed. With an ongoing five-year data set, the team has sampled over 160 vertical profiles, a dozen wildfires, and numerous stratospheric ozone intrusions. Our largest data collection includes 55 vertical profiles at Railroad Valley, NV, approximately 100 miles southwest of Great Basin National Park, and many of those flights include comparisons to surface monitors in the Nevada Rural Ozone Initiative network. We have also collected a smaller set of measurements northwest of Joshua Tree National Park, and are looking to develop partnerships that can put this data to use to assess or improve air quality in nearby Parks. AJAX also studies the plumes emitted by wildfires in California, as most emissions inventories are based on prescribed fires. We have sampled a dozen fires, and results will be presented from several, including the Rim (2013), Soberanes and Cedar (2016) Fires.

Ozone↗

NASA NTRS2007

Development of an Airborne Molecular Direct Detection Doppler Lidar for Tropospheric Wind Profiling

Global measurement of tropospheric winds is a key measurement for understanding atmospheric dynamics and improving numerical weather prediction. Global wind profiles remain a high priority for the operational weather community and also for a variety of research applications including studies of the global hydrologic cycle and transport studies of aerosols and trace species. In addition to space based winds, high altitude airborne Doppler lidar systems flown on research aircraft, UAV's or other advanced sub-orbital platforms would be of great scientific benefit for studying mesoscale dynamics and storm systems such as hurricanes. The Tropospheric Wind Lidar Technology Experiment (TWiLiTE) is a three year program to advance the technology readiness level of the key technologies and subsystems of a molecular direct detection wind lidar system by validating them, at the system level, in an integrated airborne lidar system. The TWiLiTE Doppler lidar system is designed for autonomous operation on the WB57, a high altitude aircraft operated by NASA Johnson. The WE357 is capable of flying well above the midlatitude tropopause so the downward looking lidar will measure complete profiles of the horizontal wind field through the lower stratosphere and the entire troposphere. The completed system will have the capability to profile winds in clear air from the aircraft altitude of 18 km to the surface with 250 m vertical resolution and < 3 mis velocity accuracy. Progress in technology development and status of the instrument design will be presented.

Gentry, Bruce↗

DOE OSTI2021

Environmental sensitivities of shallow-cumulus dilution – Part 2: Vertical wind profile

This second part of a numerical study on shallow-cumulus dilution focuses on the sensitivity of cloud dilution to changes in the vertical wind profile. Insights are obtained through large-eddy simulations of maritime and continental cloud fields. In these simulations, the speed of the initially uniform geostrophic wind and the strength of geostrophic vertical wind shear in the cloud and subcloud layer are varied. Increases in the cloud-layer vertical wind shear (up to 9 ms -1 km -1 ) lead to 40%–50% larger cloud-core dilution rates compared to their respective unsheared counterparts. When the background wind speed, on the other hand, is enhanced by up to 10 ms -1 and subcloud-layer vertical wind shear develops or is initially prescribed, the dilution rate decreases by up to 25%. The sensitivities of the dilution rate are linked to the updraft strength and the properties of the entrained air. Increases in the wind speed or vertical wind shear result in lower vertical velocities across all sets of experiments with stronger reductions in the cloud-layer wind shear simulation (27%–47%). Weaker updrafts are exposed to mixing with the drier surrounding air for a longer time period, allowing more entrainment to occur (i.e., the “core-exposure effect”). However, reduced vertical velocities, in concert with increased cloud-layer turbulence, also assist in widening the humid shell surrounding the cloud cores, leading to entrainment of more humid air (i.e., the “core–shell dilution effect”). In the experiments with cloud-layer vertical wind shear, the core-exposure effect dominates and the cloud-core dilution increases with increasing shear. Conversely, when the wind speed is increased and subcloud-layer vertical wind shear develops or is imposed, the core–shell dilution effect dominates to induce a buffering effect. The sensitivities are generally stronger in the maritime simulations, where weaker sensible heat fluxes lead to narrower, more tilted, and, therefore, more suppressed cumuli when cloud-layer shear is imposed. Moreover, in the experiments with subcloud wind shear, the weaker baseline turbulence in the maritime case allows for a larger turbulence enhancement, resulting in a widening of the transition zones between the cores and their environment, leading to the entrainment of more humid air.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRSDate not supplied

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

To understand such an aerodynamic characteristic of the CMC blades, we numerically simulated three different CMC blades with varying trailing edge thicknesses. We utilized both Large Eddy simulation (LES) with the dynamic subgrid closure as well a recently implemented Reynolds-averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model. We considered two sets of experimental test points with different Reynolds numbers at a given high-free stream turbulence range (Tu=~10-13%). The LES was previously validated by comparing with experimental data. We validated the RANS transition model against the ERCOFTAC experimental zero-pressure gradient smooth flat plate boundary layer at low- and high freestream turbulence offered by the experimental data of the Stripf’s for a turbine blade. We confirmed that the predicted skin friction and the heat flux agree well with the data. Finally, we computed the predicted pressure loading profiles, total loss distributions, and integrated loss of the three different CMC blades and made comparisons against the experimental data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Our paper will present the aforementioned results and discuss the ability of LES and RANS model of our choice to predict salient aerodynamic characteristics of the blades with the various trailing edge thickness effects.

LES↗

NASA NTRSDate not supplied

Numerical Investigation of the Effect of Trailing Edge Thickness of Simulated CMC Blades on Loss Profiles

To understand such an aerodynamic characteristic of the CMC blades, we numerically simulated three different CMC blades with varying trailing edge thicknesses. We utilized both Large Eddy simulation (LES) with the dynamic subgrid closure as well a recently implemented Reynolds-averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model. We considered two sets of experimental test points with different Reynolds numbers at a given high-free stream turbulence range (Tu=~10-13%). The LES was previously validated by comparing with experimental data. We validated the RANS transition model against the ERCOFTAC experimental zero-pressure gradient smooth flat plate boundary layer at low- and high freestream turbulence offered by the experimental data of the Stripf’s for a turbine blade. We confirmed that the predicted skin friction and the heat flux agree well with the data. Finally, we computed the predicted pressure loading profiles, total loss distributions, and integrated loss of the three different CMC blades and made comparisons against the experimental data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Our paper will present the aforementioned results and discuss the ability of LES and RANS model of our choice to predict salient aerodynamic characteristics of the blades with the various trailing edge thickness effects.

LES↗

NASA NTRS1992

Numerical simulations of inductive-heated float-zone growth

The present work provides an improved fluid flow and heat-transfer modeling of float-zone growth by introducing a RF heating model so that an ad hoc heating temperature profile is not necessary. Numerical simulations were carried out to study the high-temperature float-zone growth of titanium carbide single crystal. The numerical results showed that the thermocapillary convection occurring inside the molten zone tends to increase the convexity of the melt-crystal interface and decrease the maximum temperature of the molten zone, while the natural convection tends to reduce the stability of the molten zone by increasing its height. It was found that the increase of induced heating due to the increase of applied RF voltage is reduced by the decrease of zone diameter. Surface tension plays an important role in controlling the amount of induced heating. Finally, a comparison of the computed shape of the free surface with a digital image obtained during a growth run showed adequate agreement.

Chan, Y. T.↗

DOE OSTI2022

Dissecting Tensor Cores via Microbenchmarks: Latency, Throughput and Numeric Behaviors

Tensor Cores have been an important unit to accelerate Fused Matrix Multiplication Accumulation (MMA) in all NVIDIA GPUs since Volta Architecture. To program Tensor Cores, users have to use either legacy wmma APIs or current mma APIs. Legacy wmma APIs are more easy-to-use but can only exploit limited features and power of Tensor Cores. Specifically, wmma APIs support fewer operand shapes and can not leverage the new sparse matrix multiplication feature of the newest Ampere Tensor Cores. However, the performance of current programming interface has not been well explored. Furthermore, the computation numeric behaviors of low-precision floating points (TF32, BF16, and FP16) supported by the newest Ampere Tensor Cores are also mysterious. In this paper, we explore the throughput and latency of current programming APIs. Further, we intuitively study the numeric behaviors of Tensor Cores MMA and profile the intermediate operations including multiplication, addition of inner product, and accumulation. All codes used in this work can be found in https://github.com/sunlex0717/DissectingTensorCores.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1990

Two-dimensional atmospheric transport and chemistry model - Numerical experiments with a new advection algorithm

Extensive testing of the advective scheme proposed by Prather (1986) has been carried out in support of the California Institute of Technology-Jet Propulsion Laboratory two-dimensional model of the middle atmosphere. The original scheme is generalized to include higher-order moments. In addition, it is shown how well the scheme works in the presence of chemistry as well as eddy diffusion. Six types of numerical experiments including simple clock motion and pure advection in two dimensions have been investigated in detail. By comparison with analytic solutions, it is shown that the new algorithm can faithfully preserve concentration profiles, has essentially no numerical diffusion, and is superior to a typical fourth-order finite difference scheme.

Shia, Run-Lie↗

NASA NTRS1973

Three-dimensional hypersonic transitional/turbulent mean flow profiles.

Detailed three-dimensional compressible transitional/turbulent boundary-layer profiles are presented for use as test cases in numerical and integral calculation procedures. The profiles were obtained from tests conducted in the Mach 20 leg of the Langley High Reynolds Number Helium Facility. The presented data represent an arduous test case for analytical prediction methods, since 'low Reynolds number' and precursor transition effects should probably be accounted for to accurately predict the boundary-layer growth and development.

Fischer, M. C.↗

NASA NTRS1982

CONSERVB: A numerical method to compute soil water content and temperature profiles under a bare surface

A comprehensive, yet fairly simple model of water disposition in a bare soil profile under the sequential impact of rain storms and other atmospheric influences, as they occur from hour to hour is presented. This model is intended mostly to support field studies of soil moisture dynamics by our current team, to serve as a background for the microwave measurements, and, eventually, to serve as a point of departure for soil moisture predictions for estimates based in part upon airborne measurements. The main distinction of the current model is that it accounts not only for the moisture flow in the soil-atmosphere system, but also for the energy flow and, hence, calculates system temperatures. Also, the model is of a dynamic nature, capable of supporting any required degree of resolution in time and space. Much critical testing of the sample is needed before the complexities of the hydrology of a vegetated surface can be related meaningfully to microwave observations.

Vanbavel, C. H. M.↗

NASA NTRSDate not supplied

Thermal Modelling of the in-Situ Consolidation of Automated Fiber Placement of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Thermoplastics↗

NASA NTRSDate not supplied

Thermal Modelling of the In-Situ Consolidation of Automated Fiber Placement Of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Christopher J. Stelter↗

DOE OSTI2022

On the physical size of the Milky Way globular cluster NGC 7089 (M2)

ABSTRACT We study the outer regions of the Milky Way globular cluster NGC 7089 based on new Dark Energy Camera observations. The resulting background-cleaned stellar density profile reveals the existence of an extended envelope. We confirm previous results that cluster stars are found out up to ∼1° from the cluster’s centre, which is nearly three times the value of the most robust tidal radii estimations. We also used results from direct N-body simulations in order to compare with the observations. We found a fairly good agreement between the observed and numerically generated stellar density profiles. Because of the existence of gaps and substructures along globular cluster tidal tails, we closely examined the structure of the outer cluster region beyond the Jacobi radius. We extended the analysis to a sample of 35 globular clusters, 20 of them with observed tidal tails. We found that if the stellar density profile follows a power law ∝ r−α, the α slope correlates with the globular cluster present mass, in the sense that, the more massive the globular cluster, the smaller the α value. This trend is not found in globular clusters without observed tidal tails. The origin of such a phenomenon could be related, among other reasons, to the proposed so-called potential escapers or to the formation of globular clusters within dark matter minihaloes.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS2008

Experimental and Numerical Characterization of High Heat Fluxes During Transient Blackbody Calibrations

High heat fluxes are encountered in numerous applications, such as hypersonic vehicles in flight, fires, and engines, Calibration of heat flux gages may be performed in a dual cavity cylindrical blackbody resulting in a transient calibration environment. To characterize the transient heat fluxes. experiments were performed on a dual cavity cylindrical blackbody at nominal temperatures varying from 800 C to 1900 C in increments of 100 C. Based on experiments, the optimum heat flux sensor insertion location as measured from the center partition was determined. The pre-insertion steady state axial temperature profile is compared experimentally, numerically, and analytically. The effect of convection in the blackbody cavity during the insertion is calculated and found to be less than 2 per cent. Also, an empirical correlation for predicting the emissivity of the blackbody is included. Detailed transient thermal models have been developed to simulate the heat flux calibration process at two extreme fluxes. The high (1MW/sq m) and relatively low (70 kw/sq m) fluxes are reported in this article. The transient models show the effect of inserting a heat flux gage at room temperature on the thermal equilibrium of the blackbody at 1800 C and 800 C nominal temperatures, respectively. Also, heat flux sensor outputs are derived from computed sensor temperature distributions and compared to experimental results.

Abdelmessih, Amanie N.↗

NASA NTRS1989

Prediction of the aerodynamic environment and heat transfer for rotor-stator configurations

A numerical study of the aerodynamic and thermal environment associated with axial turbine stages is presented. Computations were performed using a modification of the unsteady viscous code, ROTORI, and an improved version of the steady inviscid cascade system, MERIDL-TSONIC, coupled with boundary layer codes, BLAYER and STAN5. Two different turbine stages were analyzed: the first stage of the United Technologies Research Center Large Scale Rotating Rig (LSRR) and the first stage of the Space Shuttle Main Engine (SSME) high pressure fuel turbopump turbine. The time-averaged airfoil midspan pressure and heat transfer profiles were predicted for numerous thermal boundary conditions including adiabatic wall, prescribed surface temperature, and prescribed heat flux. Computed solutions are compared with each other and with experimental data in the case of the LSRR calculations. Modified ROTORI predictions of unsteady pressure envelopes and instantaneous contour plots are also presented. Relative merits of the two computational approaches are discussed.

Griffin, L. W.↗