Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “niobium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Analysis of furnace contamination on superconducting radio frequency niobium using secondary-ion mass spectrometry

Detection of surface contamination on niobium materials used in superconducting radio frequency (SRF) applications is difficult due to quantitative sensitivity and near-atomic depth resolution needed. Inspection of samples known to have experienced surface contamination was found to have inconsistent nitride coverage after high-temperature nitrogen gas exposure (“doping”). Here we compare contaminating species found on samples treated in several different vacuum furnaces, both “exposed” directly in the chamber and “protected” by containment shielding from evaporative sources with “furnace caps.” Typically, furnace caps are used to impede contamination from reaching the interior surface of cavities during the high-temperature vacuum bake that immediately precedes exposure to nitrogen gas. Although, to date, little is known about the effectiveness of these caps, SIMS results showed that they were effective in limiting contamination arising from the furnace environment. Inspection of sample surfaces by SEM showed a lack of nitrides present on contaminated specimens. TEM with energy dispersive spectroscopy performed on these samples revealed that a carbon-rich layer now existed, indicating that a relatively high contaminant load prevents the nucleation and growth of surface nitrides, while thus inhibiting interstitial nitrogen uptake. Except in extreme cases, subsequent removal of the top several micrometers of the surface via electropolishing appears to effectively eliminate any strong influence on the subsequent SRF cavity performance. With the absence of furnace cleaning, carbon contamination was found to be nearly 10× higher for protected nitrogen-doped and electropolished samples, with minimal metallic contamination detected for both processes. SIMS analysis was also performed to compare the cleanliness of samples fully prepared by such nitrogen “doping” with those prepared by a related process, involving the dissolution of niobium surface oxide and diffusion of oxygen into the surface. This oxygen doping or alloying process offers attractive advantages.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Niobium-tin as a transformative technology for low-beta linacs

Niobium-tin has been identified as the most promising next-generation superconducting material for accelerator cavities. This is due to the higher critical temperature (Tc = 18 K) of Nb3Sn compared to niobium (TC = 9.2 K), which leads to greatly reduced RF losses in the cavity during 4.5 K operation. This allows two important changes during cavity and cryomodule design. First, the higher Tc leads to negligible BCS losses when operated at 4.5 K, which allows for a higher frequency to be used, translating to significantly smaller cavities and cryomodules. Second, the reduced dissipated power lowers the required cryogenic cooling capacity, meaning that cavities can feasibly be operated on 5-10 W cryocoolers instead of a centralized helium refrigeration plant. These plants and distribution systems are costly and complex, requiring skilled technicians for operation and maintenance. These fundamental changes present an opportunity for a paradigm shift in how low-beta linacs are designed and operated. Fabrication challenges and first coated cavity test results are discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Flux Expulsion Studies of Niobium Material of 650 MHz Cavities for PIP-II

Two different vendors supplied the niobium sheet material for PIP-II 5-cell 650 MHz cavities, which was characterized by multiple different ASTM sizes. Cavities subsequently fabricated from these sheets were heat-treated at various temperatures, then the cavities’ flux-expulsion performance was measured. Where the initial measurements of vendor O materials showed that nearly all flux remained trapped despite a high thermal gradient, 900C heat treatment subsequently improved the flux expulsion to an acceptable rate. Understanding and characterizing vendor O materials in this way is key for upcoming and future projects planning to employ niobium sheet from this supplier.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Study of Mechanical Grinding Effects on Niobium Surface

Mechanical grinding is commonly employed to eliminate surface defects such as scratches and pits from niobium cavity surfaces or sheets before cavity fabrication. Subsequently, chemically buffered polishing or electropolishing is often utilized to completely remove residues of the polishing media and any defects induced by mechanical grinding, ensuring a pristine surface. In this study, we conducted a systematic investigation to assess the influence of mechanical grinding using silicon carbide (SiC) and aluminium oxide (Al2O3) polishing media on niobium surfaces. Additionally, the study examines the effects of post-mechanical grinding chemical treatments on surface quality.

Chouhan, V.↗
DOE OSTI2025

Impact of surface growth method and surface treatment in niobium-based superconducting devices

We explore the comparison between two growth methods for niobium film - sputtering and electron-cyclotron resonance growth - for niobium-based superconducting resonators. We discuss some of the key properties of the films, including surface characterization and residual resistance measurements metrics. We present our design of various devices used in this study including superconducting resonators and qubits, both in planar configurations and integrated in 3D cavities, as well as experimental characterization of coherence metrics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Improving the Performance of Mid-T Baked Niobium Cavities through Post-Bake Surface Treatment

he Medium temperature (mid-T) baking of niobium superconducting radio-frequency cavities at 300 350 C in a vacuum furnace is known to enhance the quality factor (Q₀). However, despite this improvement, cavities treated with this process often exhibit premature quench at relatively low accelerating fields. This limitation is suspected to arise from the formation of surface contaminants, such as niobium carbides, during the furnace bake at 350 C for 3 h. To investigate the influence of potential surface contamination, this study applied an ultralight chemical removal to 1.3 GHz and 650 MHz single-cell cavities that had undergone medium-temperature baking. The removal of the top RF surface layer led to a notable improvement in the quench field and Q₀, indicating a beneficial effect of eliminating possible surface residues introduced during the bake.

Chouhan, Vijay [Fermilab]↗
DOE OSTI2026

Topographic Characterization of Niobium Films on Copper for SRF Applications

Niobium films on copper substrates are being actively developed as a low-cost alternative to bulk niobium for superconducting radio-frequency (SRF) cavities, offering superior thermal conductivity, reduced material cost, and the potential for scalable cavity fabrication. The performance of such films can be limited by imperfect surfaces that reduce the peak achievable magnetic field. Nb films deposited under varied electron cyclotron resonance conditions were characterized via atomic force microscopy. The films exhibit a corrugated surface morphology which can be characterized by the depth of the corrugation, slope angle, and standard roughness parameters. The influence of this surface roughness on field limitations is examined within the framework of London theory. These measurements and models aid in understanding how ECR deposition conditions influence the nanometer-scale roughness of Nb films on Cu and its impact on high-field SRF cavity performance.

Redman, Brandi [Old Dominion Univ., Norfolk, VA (U↗
DOE OSTI2021

Methods for synthesizing high purity niobium or rhenium powders

Methods are provided for synthesizing high purity niobium or rhenium powders by a combustion reaction. The methods can include: forming a combustion synthesis solution by dissolving in water an oxidizer, a fuel, and at least one base-soluble, ammonium salt of niobium or rhenium in amounts that yield a stoichiometric burn when combusted; and heating the combustion synthesis solution to a temperature sufficient to substantially remove the water and to initiate a self-sustaining combustion reaction.

Frye, Jr., John G.↗
DOE OSTI2022

Niobium to Titanium Electron Beam Welding for SRF Cavities

Titanium and niobium are the main materials used for the fabrication of Superconducting Radio Frequency (SRF) cavities. These two metals are usually joined , using various welding techniques, using a third material in between. This contribution focuses on the development of an innovative electron beam welding technique capable of producing a strong bond between these two different materials. Several samples are produced and tested to assess the mechanical strength at room and cryogenic temperature as well as the composition of the resulting welded joint. Also, the first units of the Single Spoke Resonator type 2 (SSR2) cavities for the Proton Improvement Plan-II (PIP-II [1]) have been fabricated joining directly various grades of titanium to niobium and results gathered through the fabrication will be reported.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Effect of successive heat treatment on the performance of superconducting radio frequency niobium cavities

One of the primary sources of radio frequency residual losses leading to lower quality factor is trapped residual magnetic field during the cooldown of superconducting radio frequency cavities. It has been reported that non-uniform recrystallization of niobium cavities after the post fabrication heat treatment leads to higher flux trapping during the cooldown, and hence the lower quality factor. Here, we fabricated two 1.3 GHz single cell cavities from high purity fine grain niobium and processed with successive heat treatments in the range 800-1000 ?C to measure the flux expulsion and flux trapping sensitivity. The results show the improved flux expulsion with increase in heat treatment temperature and flux trapping sensitivity depends on the final surface preparation prior to the rf test.

Khanal, Bashu↗
DOE OSTI2022

Temperature Mapping analysis of Nitrogen-doped Niobium Radio Frequency Cavity

Nitrogen-doping of niobium superconducting radio-frequency (SRF) cavity has been shown to significantly improve the quality factors as compared to the standard treated niobium cavities. However, the nitrogen-doped cavities generally quench at lower accelerating gradients. To understand the possible sources of rf losses in nitrogen-doped cavities that could reduce the quench field, we used 576 thermometer sensors to map the temperature distribution of the outer cavity surface while increasing the accelerating field. Our measurements have revealed a strong effect of the cavity cooldown rate on the intensity of hot spots and their spatial distribution, indicating a significant contribution from trapped vortices on the RF losses.

Makita, Junki↗
DOE OSTI2023

Demonstration of Niobium Tin in 218 MHz Low-beta Quarter Wave Accelerator Cavity

A 218 MHz quarter wave niobium cavity has been fabricated for the purpose of demonstrating Nb3Sn technology on a low-beta accelerator cavity. Niobiumtin has been established as a promising next generation SRF material, but development has focused primarily in high-beta elliptical cell cavities. This material has a significantly higher TC than niobium, allowing for design of higher frequency quarter wave cavities (that are subsequently smaller) as well as for significantly lowered cooling requirements (possibly leading to cryocooler based designs). The fabrication, initial cold testing, and Nb3Sn coating are discussed as well as test plans and details of future applications.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Growth of Native Oxides of Niobium Thin Films for Superconducting Qubits with Etching Chemistry

Niobium thin films have been broadly applied in building superconducting qubits for quantum computing hardware. While improvements have been made by device engineering efforts, scaling the energy-sensitive quantum system requires materials study for further improvements. In this study, we performed XPS and ToF-SIMS analysis for Nb thin films across samples with different manufacturing techniques. By varying the air exposure time of the samples, this research comparatively investigates the chemical and depth profile of native oxides before and after the etching process. We observe a rapid logarithmic growth of oxide thickness across all samples and the dominant presence and growth of Niobium pentoxide in atomic percentage concentration on the surface. This comparative study provides insight into oxides mitigation strategies and correlation with qubits performance.

Lei, Zhicheng↗
DOE OSTI2024

Study of Mechanical Grinding Effects on Niobium Surface

Mechanical grinding is commonly employed to eliminate surface defects such as scratches and pits from niobium cavity surfaces or sheets before cavity fabrication. Subsequently, chemically buffered polishing or electropolishing is often utilized to completely remove residues of the polishing media and any defects induced by mechanical grinding, ensuring a pristine surface. In this study, we conducted a systematic investigation to assess the influence of mechanical grinding using silicon carbide and aluminum oxide polishing media on niobium surfaces. Additionally, the study examines the effects of post-mechanical grinding chemical treatments on surface quality.

Chouhan, V.↗
DOE OSTI2026

Improving the performance of mid-T baked niobium cavities through post-bake surface treatment

The Medium temperature (mid-T) baking of niobium superconducting radio-frequency cavities at 300 350 C in a vacuum furnace is known to enhance the quality factor (Q₀). However, despite this improvement, cavities treated with this process often exhibit premature quench at relatively low accelerating fields. This limitation is suspected to arise from the formation of surface contaminants, such as niobium carbides, during the furnace bake at 350 C for 3 h. To investigate the influence of potential surface contamination, this study applied an ultralight chemical removal to 1.3 GHz and 650 MHz single-cell cavities that had undergone medium-temperature baking. The removal of the top RF surface layer led to a notable improvement in the quench field and Q₀, indicating a beneficial effect of eliminating possible surface residues introduced during the bake.

Chouhan, V. [Fermilab] (ORCID:0000000282004931)↗
DOE OSTI2023

Electropolishing parameters study for surface smoothening of low-$\beta$650 MHz five-cell niobium superconducting radio frequency cavity

Electropolishing (EP) is applied to niobium (Nb) superconducting radio frequency (SRF) cavities, which are used in particle accelerators for their surface treatment. The EP process for 1.3 GHz cavities has been extensively studied earlier. In this work, a parametric study on EP of low-β (0.61) 650 MHz Nb SRF cavities (LB650), which will be used in pre-production cryomodule for proton improvement plan-II (PIP-II) linear accelerator, was conducted to determine adequate EP conditions for attaining a smooth surface of the cavities. EP performed with the standard parameters and an initial cathode (cathode-I) having a cathode surface area of ~5% of the cavity surface area yielded a rough equator surface of the cavity. The grain step height on the equator weld position was measured to be ~ 32 μm. The rough surface was attributed to preferential grain etching confirmed by a polarization curve showing a linear relationship between the EP current and voltage and the absence of the current plateau region. The cathode was modified to make its surface area twice that of cathode-I. The modified cathode (cathode-M) provided a current plateau region in the corresponding I-V curves measured at different cavity temperatures. The onset voltage for the plateau was found to be higher at higher cavity temperatures. Here this study revealed that even with cathode-M, the standard 18 V was low for EP of such large-sized cavities when the cavity temperature was 18 °C. EP performed at a higher voltage of 22–24.5 V with cathode-M yielded a smooth surface with a grain step height of only 0.6 μm. The applied EP conditions also improved removal uniformity along the cavity length. In contrast to the cavity treated with cathode-I, the cavities treated with cathode-M achieved a significantly higher accelerating gradient (E acc ) in vertical tests conducted in a cryostat at 2 K. The modified EP was found efficient to produce the cavities that achieved E acc of 22.4 MV/m, required by PIP II project in the baseline RF tests, to qualify for further surface processing used to enhance their quality factors.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Enhancement of oxidative dehydrogenation over cerium-doped nickel niobium catalysts and analysis of batch-to-batch variability

Nickel based catalysts are inexpensive and efficient for use in the oxidative dehydrogenation of ethane. NiO doped with niobium and cerium shows increased ethylene production. Small amounts of Ce doped onto a NiNb catalyst led to increased Ni activity. The catalyst that had the highest ethylene production rate per g of catalyst had 1 atom% Ce, 86 at% Ni, and 13 at% Nb (1CeNiNb) while, if surface area is incorporated into the calculation, the catalyst that had the highest ethylene production rate per m 2 was the 0.5CeNiNb catalyst. The ethylene production rates of these Ce-containing catalysts are 27 %-127 % higher than those with NiNb alone previously reported in the literature. Here, to fully understand how cerium affects the NiNb catalyst, the Ce content and effect on active sites has been fully characterized over multiple batches. In doing this, light has been shed on batch-to-batch variability. Characterization techniques such as powder X-ray diffraction, hydrogen temperature programmed reduction, X-ray photoelectron spectroscopy, synchrotron X-ray absorption spectroscopy, and methanol adsorption were used.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Preventing native oxide formation in niobium thin films through platinum encapsulation

Superconducting transmon qubits are a key technology in quantum computing, with niobium (Nb) widely used due to its favorable superconducting properties and compatibility with scalable fabrication. However, the performance of Nb-based qubits is hindered by two-level systems (TLS), which arise predominantly from native oxide layers at surfaces and interfaces. These oxides and suboxides form rapidly in air and contribute significantly to decoherence by introducing dielectric losses. While various mitigation strategies, including thermal-annealing, chemical-etching, and nitrogen plasma treatment, have been explored, many are challenging to integrate into large-scale manufacturing due to complexity and instability in ambient conditions. In this study, we investigate the structural, chemical, and superconducting properties of room-temperature sputtered Nb thin films grown on sapphire substrates. We focus on a surface protection strategy using noble metal encapsulation with platinum (Pt) to suppress oxides and reduce TLS-related losses. Structural and chemical characterization were performed using X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. Superconducting properties were measured using a physical property measurement system. Results demonstrate that Pt encapsulation effectively suppresses surface oxidation and mitigates its detrimental impact on superconducting performance. In conclusion, this approach offers a promising path toward enhancing the coherence of Nb-based qubits while remaining compatible with scalable-fabrication processes.

36 MATERIALS SCIENCE↗