Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “nanostructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Nonequilibrium defect-phase nanostructures stabilized by irradiation in undersaturated Ni-Si nanocrystalline alloy

Nanocrystalline thin films of the undersaturated alloy Ni-8.5 at% Si were subjected to 2 MeV Ti irradiation at temperatures ranging from 450˚C to 550˚C. Correlative microscopy combining transmission electron microscopy (TEM), scanning-TEM and atom probe tomography (APT revealed that large dose irradiation at 450˚C of samples with initial grain sizes below 100 nm stabilized a novel nanostructure which surprisingly contained three co-existing phases, the γ face-centered-cubic (FCC) matrix, γ' L12 ordered precipitates on intragranular dislocation loops and Ni 31 Si 12 precipitates at triple junctions (TJs). In contrast, irradiation at 550˚C and irradiation of larger grain-size samples at 450˚C only produced a γ-γ' two-phase coexistence. Analysis of the three-phase nanostructure and phase field simulations indicates that radiation-induced segregation is most pronounced at TJs, thus triggering the formation of Ni 31 Si 12 precipitates. These incoherent precipitates, in turn, are expected to stabilize the grain size under irradiation. The results are generalized using the concept of driven defect-phases. It is suggested that the stabilization of driven defect-phases may impart radiation resilience by providing localized relaxation modes to the microstructure evolution during and after temporary perturbations in irradiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanostructural evolution of Al(OH)3 gel formed by the cubic and orthorhombic ye'elimite clinkers of calcium sulfoaluminate cements in an ultra-wide hydration temperature range

This paper investigated the influence of hydration temperature on the nanostructure of the AH{sub 3} phase formed in calcium sulfoaluminate cements. Orthorhombic ye'elimite (st-ye'elimite) and cubic ye'elimite (ss-ye'elimite) were hydrated in an ultra-wide temperature range (5–220 °C). Results showed that the AH{sub 3} phase formed by ss-ye'elimite was always microcrystalline in nature at various curing temperatures (5–130 °C), and transformed into the AlOOH phase at 150 °C and above. However, the AH{sub 3} phase formed by st-ye'elimite grew from a microcrystal to a favorable crystal as the temperature increased, and transformed into the AlOOH phase at 170 °C and above. The nanostructure of hydration products was further investigated using TEM/SAED analysis together with FE-SEM images, directly evidencing that the formed AFm-12 phase was single-crystal in nature, and the formed AH{sub 3} phase was microcrystalline at low temperatures and grew into single-crystal hexagonal prisms with the preferred growth direction along [001] direction at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In situ study on medium-range order evolution during the polyamorphous phase transition in a Pd-Ni-P nanostructured glass

Engineering multiscale structural hierarchies in glassy alloys enable a broad spectrum of potential applications. Metallic glasses were born in hierarchical structures from atomic-to-nanometer scales. However, the frozen-in structures in traditional metallic glasses prepared by rapid quenching techniques are challenging to tailor. Here, we show that a Pd 40 Ni 40 P 20 bulk nanostructured glass of polyamorphous interfacial structures was prepared by inert-gas condensation with a laser evaporation source, and its multiscale structures could be engineered. In-situ scattering experiment results reveal polyamorphous phase transitions occurred in the interfacial regions, which are accompanied by the evolution of medium-range order and the nanoscale heterogeneous structures during the condensation process of glassy nanoparticles under high pressure and the following heating process. Moreover, changes in the cluster connectivity resulting from repacking of the local ordering induced by pressure and temperature could be observed. The thermophysical and mechanical properties, including boson peaks, hardness, and elasticity modulus, could be changed as a function of heat-treatment parameters. In conclusion, our findings would shed light on the synthesis of bulk nanostructured glassy alloys with tailorable thermodynamic and dynamical behavior as well as mechanical properties based on the understanding of metastability for polyamorphous interfacial phases.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Chiral Spectroscopy of Nanostructures

Chirality is ubiquitous in the universe and in living creatures over detectable length scales from the subatomic to the galactic, as exemplified in the two extremes by subatomic particles (neutrinos) and spiral galaxies. Between them are living creatures that display multiple levels of chirality emerging from hierarchically assembled asymmetric building blocks. Not too far from the bottom of this pyramid are the foundational building blocks with chiral atomic centers on sp 3 carbon atoms exemplified by L-amino acids and D-sugars that are self-assembled into higher-order structures with increasing dimensions forming highly complex, amazingly functional, and energy-efficient living systems. The organization and materials employed in their construction inspired scientists to replicate complex living systems via the self-assembly of chiral components. Multiple studies pointed to unexpected and unique electromagnetic properties of chiral structures with nanoscale and microscale dimensions, including giant circular dichroism and collective circularly polarized scattering that their constituent units did not possess. To address the wide variety of chiral geometries observed in continuous materials, singular particles, and their complex systems, multiple analytic techniques are needed. Simultaneously, their spectroscopic properties create a pathway to multiple applications. For example, mirror-asymmetric vibrations at chiral centers formed by sp 3 carbon atoms lead to optical activity for the infrared (IR) wavelength regions. At the same time, understanding the optical activity in, for example, the IR region enables biomedical applications because multiple modalities of biomedical imaging and vibrational optical activity (VOA) of biomolecules are known for IR range. In turn, VOA can be realized in both absorption and emission modalities due to large magnetic transition moments, as vibrational circular dichroism (VCD) or Raman optical activity (ROA) spectroscopy. In addition to the VOA, in the range of longer wavelengths, lattice vibrational mode or phononic behavior occurs in chiral crystals and nanoassemblies, which can be readily detected by terahertz circular dichroism (TCD) spectroscopy. Meanwhile, chiral self-assembly can induce circularly polarized light emission (CPLE) regardless of the existence of chirality in coassembled fluorophores. The CPLE from self-assembled chiral materials is particularly interesting because the CPLE can originate from both circularly polarized luminescence and circularly polarized scattering (CPS). Furthermore, because self-assembled nanostructures often exhibit stronger optical activity than their building blocks owing to dimension and resonance effects, the optical activity of single assembled nanostructures can be investigated by using microscopic technology combined with chiral optics. Here, we describe the state of the art for spectroscopic methods for the comprehensive analysis of chiral nanomaterials at various photon wavelengths, addressed with special attention given to new tools emerging both for materials with self-organized hierarchical chirality and single-particle spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Design and Control of Three-Dimensional Topological Magnetic Fields Using Interwoven Helical Nanostructures

Three-dimensional (3D) magnetic nanostructures are an emerging platform capable of creating complex topological magnetic fields. The control of localized nanoscale magnetic fields is seen to be of importance for diverse areas from bioapplications such as drug delivery, to particle trapping and controlling Majorana Fermions for quantum computing. Three-dimensional geometric confinement and proximity can create tailor-made spin textures not possible in two dimensions. The control of magnetization afforded here can allow the formation of unique stray field textures. Here, we report the creation of reconfigurable 3D topological magnetic field textures induced by an interwoven 3D nanostructure and applied field protocol. These field textures emerge due to distinct DWs formed in this structure and lead to the creation of an antivortex field, a hexapole cusp and a 3D skyrmion field tube of mixed chirality. In conclusion, our results therefore show a key step toward the design and control of topological magnetic fields on the nanoscale.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strategy for Nonenzymatic Harvesting of Cells via Decoupling of Adhesive and Disjoining Domains of Nanostructured Stimulus-Responsive Polymer Films

The nanostructured polymer film introduces a novel mechanism of nonenzymatic cell harvesting by decoupling solid cell-adhesive and soft stimulus-responsive cell-disjoining areas on the surface. The key characteristics of this architecture are the decoupling of adhesion from detachment and the impermeability to the integrin protein complex of the adhesive domains. This surface design eliminates inherent limitations of thermoresponsive coatings, namely, the necessity for the precise thickness of the coating, grafting or cross-linking density, and material of the basal substrate. The concept is demonstrated with nanostructured thermoresponsive films made of cell-adhesive epoxy photoresist domains and cell-disjoining poly(N-isopropylacrylamide) brush domains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Sequential Infiltration Synthesis of Bilayer Porous Alumina Nanostructures for Broad-Angle, Broadband Antireflective Coatings

Antireflective coatings (ARCs) are thin films engineered to reduce light reflections. Delivering broadband, wide-angle performance is essential for photovoltaics, imaging, and sensing, yet truly omnidirectional antireflection remains difficult due to angle-dependent optical paths and a narrow palette of suitable refractive indices. Here, in this study, we systematically investigate an emerging class of multilayer inorganic ARCs based on conformally coated nanoporous alumina templated by intrinsically microporous polymers (PIMs) and block copolymers (BCPs). We establish a design framework that maps thickness reflectance relationships to identify thickness pairs minimizing reflection across wavelength and incidence angle. We show that deliberately separating the local reflectance minima of the top and bottom layers in bilayer nanostructures broadens the antireflective bandwidth and angular range. We show that 235-nm single-side bilayer porous alumina nanostructures achieves under 2 % reflectance from 380–750 nm for incidence angles up to 45° with less than 0.6% reflectance for incidence angles under 20°. The approach is readily extensible to additional layers or materials with refractive indices tuned via templated nanoporosity and composition, enabling practical, etch-free ARC fabrication without HF or fluorinated precursors and advancing straightforward design of broadband, wide-angle (quasi-omnidirectional) ARCs for next-generation optical systems.

antireflective coatings↗
DOE OSTI2022

Nontrivial nanostructure, stress relaxation mechanisms, and crystallography for pressure-induced Si-I → Si-II phase transformation

Crystallographic theory based on energy minimization suggests austenite-twinned martensite interfaces with specific orientation, which are confirmed experimentally for various materials. Pressure-induced phase transformation (PT) from semiconducting Si-I to metallic Si-II, due to very large and anisotropic transformation strain, may challenge this theory. Here, unexpected nanostructure evolution during Si-I → Si-II PT is revealed by combining molecular dynamics (MD), crystallographic theory, generalized for strained crystals, and in situ real-time Laue X-ray diffraction (XRD). Twinned Si-II, consisting of two martensitic variants, and unexpected nanobands, consisting of alternating strongly deformed and rotated residual Si-I and third variant of Si-II, form {111} interface with Si-I and produce almost self-accommodated nanostructure despite the large transformation volumetric strain of -0.237. The interfacial bands arrest the {111} interfaces, leading to repeating nucleation-growth-arrest process and to growth by propagating {110} interface, which (as well as {111} interface) do not appear in traditional crystallographic theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Pulsed laser heating of diesel engine and turbojet combustor soot: Changes in nanostructure and implications

Here, carbonaceous particulate produced by a diesel engine and turbojet engine combustor are analyzed by transmission electron microscopy (TEM) for differences in nanostructure before and after pulsed laser annealing. Soot is examined between low/high diesel engine torque and low/high turbojet engine thrust. Small differences in nascent nanostructure are magnified by the action of high-temperature annealing induced by pulsed laser heating. Lamellae length distributions show occurrence of graphitization while tortuosity analyses reveal lamellae straightening. Differences in internal particle structure (hollow shells versus internal graphitic ribbons) are interpreted as due to higher internal sp3 and O-atom content under the higher power conditions with hypothesized greater turbulence and resulting partial premixing. TEM in concert with fringe analyses reveal that a similar degree of annealing occurs in the primary particles in soot from both diesel engine and turbojet engine combustors—despite the aggregate and primary size differences between these sources. Implications of these results for source identification of the combustion particulate and for laser-induced incandescence (LII) measurements of concentration are discussed with inter-instrument comparison of soot mass from both diesel and turbojet soot sources.

42 ENGINEERING↗
DOE OSTI2023

In-situ study of rules of nanostructure evolution, severe plastic deformations, and friction under high pressure

Severe plastic deformations under high pressure are used to produce nanostructured materials but were studied ex-situ. Rough diamond anvils are introduced to reach maximum friction equal to yield strength in shear and the first in-situ study of the evolution of the pressure-dependent yield strength and radial distribution of nanostructural parameters are performed for severely pre-deformed Zr. ω-Zr behaves like perfectly plastic, isotropic, and strain-path-independent and reaches steady values of the crystallite size and dislocation density, which are pressure-, strain- and strain-path-independent. However, steady states for a-Zr obtained with smooth and rough anvils are different, causing major challenge in plasticity theory. In-situ study of severe plastic deformation of α-Zr with rough diamond anvils revealed that pressure-dependent yield strength, crystallite size, and dislocation density are getting steady and plastic strain- and strain-path-independent.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Superior plastic flow stability of self-patterned carbide – amorphous ceramic nanostructures

Amorphous ceramics and carbides exhibit superb strength but poor plasticity. Here, we synthesized TiC-SiOC nanostructures with TiC-nanocarbides embedded in amorphous ceramic SiOC by co-sputtering followed by high-temperature annealing and/or irradiation. TiC-SiOC nanostructures exhibit high strength and good plastic flow stability even after heavy irradiation, 7 GPa at room temperature and 3.6 GPa at 700 ℃ with a uniform strain of about 10%∼18%. The uniform deformation is accommodated by the shearing of amorphous ceramic and the rotation of nanocarbides. Nanocarbides inhibit the propagation of shear banding in amorphous SiOC, and amorphous-crystal interfaces act as sinks to manage irradiation-induced defects.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sustainable and Green Production of Nanostructured Cellulose by a 2-Step Mechano-Enzymatic Process

Nanostructured cellulose (NC) represents an emerging sustainable biomaterial for diverse biotechnological applications; however, its production requires hazardous chemicals that render the process ecologically unfriendly. Using commercial plant-derived cellulose, an innovative strategy for NC production based on the combination of mechanical and enzymatic approaches was proposed as a sustainable alternative to conventional chemical procedures. After ball milling, the average length of the fibers was reduced by one order of magnitude (down to 10–20 μm) and the crystallinity index decreased from 0.54 to 0.07–0.18. Moreover, a 60 min ball milling pre-treatment followed by 3 h Cellic Ctec2 enzymatic hydrolysis led to NC production (15% yield). Analysis of the structural features of NC obtained by the mechano-enzymatic process revealed that the diameters of the obtained cellulose fibrils and particles were in the range of 200–500 nm and approximately 50 nm, respectively. Interestingly, the film-forming property on polyethylene (coating ≅ 2 μm thickness) was successfully demonstrated and a significant reduction (18%) of the oxygen transmission rate was obtained. Altogether, these findings demonstrated that nanostructured cellulose could be successfully produced using a novel, cheap, and rapid 2-step physico-enzymatic process that provides a potential green and sustainable route that could be exploitable in future biorefineries.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Synthesis of 2H/ fcc -Heterophase AuCu Nanostructures for Highly Efficient Electrochemical CO 2 Reduction at Industrial Current Densities

Structural engineering of nanomaterials offers a promising way for developing high-performance catalysts toward catalysis. However, the delicate modulation of thermodynamically unfavorable nanostructures with unconventional phases still remains a challenge. Here, in this study, the synthesis of hierarchical AuCu nanostructures is reported with hexagonal close-packed (2H-type)/face-centered cubic (fcc) heterophase, high-index facets, planar defects (e.g., stacking faults, twin boundaries, and grain boundaries), and tunable Cu content. The obtained 2H/fcc Au 99 Cu 1 hierarchical nanosheets exhibit excellent performance for the electrocatalytic CO 2 reduction to produce CO, outperforming the 2H/fcc Au 91 Cu 9 and fcc Au 99 Cu 1 . The experimental results, especially those obtained by in-situ differential electrochemical mass spectroscopy and attenuated total reflection Fourier-transform infrared spectroscopy, suggest that the enhanced catalytic performance of 2H/fcc Au 99 Cu 1 arises from the unconventional 2H/fcc heterophase, high-index facets, planar defects, and appropriate alloying of Cu. Impressively, the 2H/fcc Au 99 Cu 1 shows CO Faradaic efficiencies of 96.6% and 92.6% at industrial current densities of 300 and 500 mA cm -2 , respectively, as well as good durability, placing it among the best CO 2 reduction electrocatalysts for CO production. The atomically structural regulation based on phase engineering of nanomaterials (PEN) provides an avenue for the rational design and preparation of high-performance electrocatalysts for various catalytic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxidation Driven Thin‐Film Solid‐State Metal Dealloying Forming Bicontinuous Nanostructures

Abstract Solid‐state metal dealloying (SSMD) is a promising method for fabricating nanoscale metallic composites and nanoporous metals across a range of materials. Thin‐film SSMD is particularly attractive due to its ability to create fine features via solid‐state interfacial reactions within a thin‐film geometry, which can be integrated into devices for various applications. This work examines a new dealloying couple, namely the Nb–Al alloy with the dealloying agent Sc, as previously predicted in the machine‐learning (ML) models. Prior ML predictions aimed to guide the design of nanoarchitectured materials through dealloying, relying on intuition‐driven discovery within a large parameter space. However, this work reveals that at the nanoscale, the involvement of oxygen in thin film processing may instead drive the dealloying process, resulting in the formation of bicontinuous nanostructures similar to those formed by metal‐agent dealloying. The phase evolution, as well as chemical and morphological changes, are closely analyzed using a combination of X‐ray absorption spectroscopy, diffraction, and scanning transmission electron microscopy to understand the mechanisms behind nanostructure formation. The findings suggest a potential pathway for utilizing oxygen to drive the formation of bicontinuous metal–metal oxide nanocomposites, paving the way for further development of functional nanoporous materials in diverse fields.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Spatiotemporal Studies of Soluble Inorganic Nanostructures with X‐rays and Neutrons

Abstract This Review addresses the use of X‐ray and neutron scattering as well as X‐ray absorption to describe how inorganic nanostructured materials assemble, evolve, and function in solution. We first provide an overview of techniques and instrumentation (both large user facilities and benchtop). We review recent studies of soluble inorganic nanostructure assembly, covering the disciplines of materials synthesis, processes in nature, nuclear materials, and the widely applicable fundamental processes of hydrophobic interactions and ion pairing. Reviewed studies cover size regimes and length scales ranging from sub‐Ångström (coordination chemistry and ion pairing) to several nanometers (molecular clusters, i.e. polyoxometalates, polyoxocations, and metal‐organic polyhedra), to the mesoscale (supramolecular assembly processes). Reviewed studies predominantly exploit 1) SAXS/WAXS/SANS (small‐ and wide‐angle X‐ray or neutron scattering), 2) PDF (pair‐distribution function analysis of X‐ray total scattering), and 3) XANES and EXAFS (X‐ray absorption near‐edge structure and extended X‐ray absorption fine structure, respectively). While the scattering techniques provide structural information, X‐ray absorption yields the oxidation state in addition to the local coordination. Our goal for this Review is to provide information and inspiration for the inorganic/materials science communities that may benefit from elucidating the role of solution speciation in natural and synthetic processes.

Yin, Jia‐Fu↗
DOE OSTI2022

In Situ Growth of Crystalline and Polymer-Incorporated Amorphous ZIFs in Polybenzimidazole Achieving Hierarchical Nanostructures for Carbon Capture

We report mixed matrix materials (MMMs) hold great potential for membrane gas separations by merging nanofillers with unique nanostructures and polymers with excellent processability. In situ growth of the nanofillers is adapted to mitigate interfacial incompatibility to avoid the selectivity loss. Surprisingly, functional polymers have not been exploited to co-grow the nanofillers for membrane applications. Herein, in situ synergistic growth of crystalline zeolite imidazole framework-8 (ZIF-8) in polybenzimidazole (PBI), creating highly porous structures with high gas permeability, is demonstrated. More importantly, PBI contains benzimidazole groups (similar to the precursor for ZIF-8, i.e., 2-methylimidazole) and induces the formation of amorphous ZIFs, enhancing interfacial compatibility and creating highly size-discriminating bottlenecks. For instance, the formation of 15 mass% ZIF-8 in PBI improves H- 2 permeability and H- 2 /CO 2 selectivity by approximate to 100% at 35 degrees C, breaking the permeability/selectivity tradeoff. This work unveils a new platform of MMMs comprising functional polymer-incorporated amorphous ZIFs with hierarchical nanostructures for various applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Binary Atomically Dispersed Metal-Site Catalysts with Core–Shell Nanostructures for O 2 and CO 2 Reduction Reactions

Engineering atomically dispersed metal site catalysts with controlled local coordination environments and 3D nanostructures effectively improves the catalytic performance for the oxygen reduction reaction (ORR) and the carbon dioxide reduction reaction (CO 2 RR), which are critical for clean energy conversion and chemical production. Herein, an innovative approach for preparing core-shell nanostructured catalysts with different single-metal sites in the core and the shell, respectively, is developed. In particular, as the shell precursors, covalent organic polymers with a thin layered structure that is polymerized in situ and coated on a metal-doped ZIF-derived carbon core are used, followed by a controlled thermal activation. The selective combination and construction of different metal sites increase active site density in the surface layers, promote structural robustness, facilitate mass/charge transfer, and yield a possible synergy of active sites in the core and the shell. The p-FeNC(shell)@CoNC(core), consisting of a polymerized FeTPPCl-derived carbon layer (p-FeNC) on a Co-doped ZIF-derived carbon (CoNC), exhibits remarkable ORR activity and stability in acidic media along with encouraging durability in H 2 –air fuel cells. Likewise, a p-FeNC(shell)@NiNC(core) catalyst demonstrates outstanding CO 2 RR activity and stability. Hence, integrating two appropriate single-metal sites in core and shell precursors, respectively, can modulate morphological and catalytic properties for a possible synergy toward different electrocatalysis processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Gradient nanostructuring via compositional means

Nanocrystalline metals are inherently unstable against thermal and mechanical stimuli, commonly resulting in significant grain growth. Also, while these metals exhibit substantial Hall-Petch strengthening, they tend to suffer from low ductility and fracture toughness. With regard to the grain growth problem, alloying elements have been employed to stabilize the microstructure through kinetic and/or thermodynamic mechanisms. And to address the ductility challenge, spatially-graded grain size distributions have been developed to facilitate heterogeneous deformation modes: high-strength at the surface and plastic deformation in the bulk. In the present work, we combine these two strategies and present a new methodology for the fabrication of gradient nanostructured metals via compositional means. Here, we have demonstrated that annealing a compositionally stepwise Pt-Au film with a homogenous microstructure results in a film with a spatial microstructural gradient, exhibiting grains which can be twice as wide in the bulk compared to the outer surfaces. Additionally, phase-field modeling was employed for the comparison with experimental results and for further investigation of the competing mechanisms of Au diffusion and thermally induced grain growth. This fabrication method offers an alternative approach for developing the next generation of microstructurally stable gradient nanostructured films.

36 MATERIALS SCIENCE↗