Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “modal filtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Precision Pointing Improvements for the Lunar Reconnaissance Orbiter Camera

The Lunar Reconnaissance Orbiter (LRO) was launched in 2009 and, with its seven science instruments, continues to make remarkable discoveries of the Moon. LRO is in a slightly elliptical, polar lunar orbit and nominally maintains a nadir orientation. In early 2018, the Miniature Inertial Measurement Unit (MIMU) was powered off following a fairly rapid decline in the laser intensity on the X axis. An algorithm combining star tracker quaternion differentiated rates and integrated control torque commands in a complementary filter, now provides the onboard rate estimate, replacing the MIMU. One of the science instruments, the LRO Camera(LROC) system, contains a Wide Angle Camera (WAC) and two Narrow Angle Cameras (NAC). The NACs suffer from larger attitude drifts during imaging of the Moon for stereo image processing, resulting from pointing stability degradation of the star tracker derived rates. The controller gains and structural filter were redesigned to attenuate the new disturbances while also maintaining adequate stability and modal suppression. This paper documents the development, testing, and operational implementation of the revised control system parameters, specifically targeted for use during LROC imaging. The new parameters improved pointing performance for LROC.

Julie Halverson↗
NASA NTRSDate not supplied

Distributed Target Tracking With Optimal Data Migration

The paper presents an Extended Kalman Filter based framework for airborne target tracking using dynamic information fusion from multi-modal sensors with geodiversity. First, the algorithm execution location is determined using an optimal data migration strategy, next the sensors information is dynamically fused at each estimation instance using validity flag for each sensor reading, finally the target estimation is updated based on the fused innovation vector. The approach is applied to synthetic data generated from the radar and camera models located on the ground for the simulated target flight in Reflection simulation environment.

Distributed sensing↗
NASA NTRS1993

An overview of recent advances in system identification

This paper presents an overview of the recent advances in system identification for modal testing and control of large flexible structures. Several techniques are discussed including the Observer/Kalman Filter Identification, the Observer/Controller Identification and the State-Space System Identification in the Frequency Domain. The System/Observer/Controller Toolbox developed at NASA Langley Research Center is used to show the applications of these techniques to real aerospace structures such as the Hubble spacecraft telescope and the active flexible aircraft wing.

Juang, Jer-Nan↗
NASA NTRS1994

An overview of recent advances in system identification

This paper presents an overview of the recent advances in system identification for modal testing and control of large flexible structures. Several techniques are discussed including the Observer/Kalman Filter Identification, the Observer/Controller Identification, and the State-Space System Identification in the Frequency Domain. The System/Observer/Controller Toolbox developed at NASA Langley Research Center is used to show the applications of these techniques to real aerospace structures such as the Hubble spacecraft telescope and the active flexible aircraft wing.

Juang, Jer-Nan↗
NASA NTRS1983

Decoupling and observation theory applied to control of a long flexible beam in orbit

Techniques which use decoupling theory and state variable feedback to control the pitch attitude and the flexible mode amplitudes of a long, thin beam are discussed. An observer based on the steady state Kalman filter was incorporated into the control design procedure in order to estimate the values of the modal state variables required for the feedback control law.

Hamer, H. A.↗
NASA NTRS1983

Adaptive control of a flexible beam using least square lattice filters

This paper presents an indirect adaptive control scheme for the control of flexible structures using recursive least square lattice filters. The identification scheme uses lattice filters which provide an on-line estimate of the number of modes, mode shapes and modal amplitudes. These modes are coupled and a transformation to decouple them in order to obtain the natural modes is presented. The decoupled modal amplitude time series are then used in an equation error identification scheme to identify the model parameters in an autoregressive moving average (ARMA) form. The control is based on modal pole placement scheme with the objective of vibration suppression. The control gains are calculated based on the identified ARMA parameters. Before using the identified parameters for control, detailed testing and validation procedures are carried out on the identified parameters. The full adaptive control scheme is demonstrated using the simulation for the 12 foot free-free beam apparatus at NASA Langley Research Center.

Sundararajan, N.↗
NASA NTRS1992

Spatial filters for shape control

Recently there has emerged a new class of sensors, called spatial filters, for structures which respond over a significant gauge length. Examples include piezoelectric laminate PVDF film, modal domain optical fiber sensors, and holographic sensors. These sensors have a unique capability in that they can be fabricated to locally alter their sensitivity to the measurand. In this paper we discuss how these sensors can be used for the implementation of control algorithms for the suppression of acoustic radiation from flexible structures. Based on this relationship between the total power radiated to the far field to the modal velocities of the structure, we show how the sensor placement to optimize the control algorithm to suppress the radiated power.

Lindner, Douglas K.↗
NASA NTRS2023

A Hybrid Transfer Function Procedure for Broadband Auralization Within Small Flight Vehicle Interiors

Auralization of the sound fields within flight vehicle interiors is of interest to aircraft designers considering crew and passenger ride quality. Computer models can be used to predict the filtering effects that the fuselage structure and interior volume have on the exterior sound field in order to simulate the resulting cabin interior noise. However, this can become expensive when a wide frequency range of analysis suitable for passenger auralization is desired. This is particularly the case when using deterministic modeling methods such as finite element analysis (FEA) wherein prohibitively high levels of detail and finite element discretizations are required to resolve the wavelengths at high frequencies. On the contrary, Statistical Energy Analysis (SEA), while not capturing important modal behaviors at low frequencies, is better suited for higher frequency analyses where structural and interior dynamics exhibit high modal overlap and spatially averaged physical quantities suffice. For this reason, a hybrid procedure is considered here that utilizes FE modal solutions at lower frequencies and SEA results at higher frequencies. A transfer function dataset containing the exterior to interior vibroacoustic filtering effect is calculated accordingly and subsequently stored to be used for a variety of exterior dynamic load cases. At low frequencies, the transfer function dataset detail is related to the level of FE model refinement whereas at high frequencies it functions as an equalizer array with a level of detail corresponding to the SEA subsystem partitioning scheme. The above procedure is described herein and demonstrated on a six passenger flight vehicle with eight propulsors in a hover flight condition.

auralization↗
NASA NTRS2023

A Hybrid Transfer Function Procedure for Broadband Auralization Within Small Flight Vehicle Interiors

Auralization of the sound fields within flight vehicle interiors is of interest to aircraft designers considering crew and passenger ride quality. Computer models can be used to predict the filtering effects that the fuselage structure and interior volume have on the exterior sound field in order to simulate the resulting cabin interior noise. However, this can become expensive when a wide frequency range of analysis suitable for passenger auralization is desired. This is particularly the case when using deterministic modeling methods such as finite element analysis (FEA) wherein prohibitively high levels of detail and finite element discretizations are required to resolve the wavelengths at high frequencies. On the contrary, Statistical Energy Analysis (SEA), while not capturing important modal behaviors at low frequencies, is better suited for higher frequency analyses where structural and interior dynamics exhibit high modal overlap and spatially averaged physical quantities suffice. For this reason, a hybrid procedure is considered here that utilizes FE modal solutions at lower frequencies and SEA results at higher frequencies. A transfer function dataset containing the exterior to interior vibroacoustic filtering effect is calculated accordingly and subsequently stored to be used for a variety of exterior dynamic load cases. At low frequencies, the transfer function dataset detail is related to the level of FE model refinement whereas at high frequencies it functions as an equalizer array with a level of detail corresponding to the SEA subsystem partitioning scheme. The above procedure is described herein and demonstrated on a six passenger flight vehicle with eight propulsors in a hover flight condition.

auralization↗
NASA NTRS1986

Control design for robust stability in linear regulators: Application to aerospace flight control

Time domain stability robustness analysis and design for linear multivariable uncertain systems with bounded uncertainties is the central theme of the research. After reviewing the recently developed upper bounds on the linear elemental (structured), time varying perturbation of an asymptotically stable linear time invariant regulator, it is shown that it is possible to further improve these bounds by employing state transformations. Then introducing a quantitative measure called the stability robustness index, a state feedback conrol design algorithm is presented for a general linear regulator problem and then specialized to the case of modal systems as well as matched systems. The extension of the algorithm to stochastic systems with Kalman filter as the state estimator is presented. Finally an algorithm for robust dynamic compensator design is presented using Parameter Optimization (PO) procedure. Applications in a aircraft control and flexible structure control are presented along with a comparison with other existing methods.

Yedavalli, R. K.↗
DOE OSTI2020

Adaptive noise canceling for transient absorption microscopy

Significance: Ultrafast fiber lasers are an attractive alternative to bulk lasers for nonlinear optical microscopy for their compactness and low cost. The high relative intensity noise (RIN) of these lasers poses a challenge for pump-probe measurements such as transient absorption and stimulated Raman scattering, along with modalities that provide label-free contrast from the vibrational and electronic structure of molecules. Aim: Digital adaptive filtering was applied to determine the applicability for canceling laser RIN in a transient absorption microscope with an ultrafast fiber laser source. Approach: Digitized signals from the transmitted probe and reference photodetectors were fed to an adaptive filter in MATLAB, running in a noise canceling configuration. This result was then fed to a software lock-in algorithm to demodulate the pump-probe signal. Images were built up one line scan at a time with a 3.5-kHz resonant scanner, with 100× averaging. The imaging target was Bi4Ge3O12, which exhibits nondegenerate two-photon absorption at the pump/probe wavelengths used (530-nm pump and 490-nm probe). Results: Without adaptive noise cancellation, the lock-in output primarily passes the laser RIN within its detection bandwidth, resulting in images that closely follow the linear transmissivity and lack sensitivity to pump-probe time delay. With adaptive noise cancellation in front of the lock-in, the RIN rejection is enough to restore the z-sectioning and sensitivity to pump-probe delay, as expected for transient absorption. Results were limited primarily by noise from the photodetector and analog-to-digital converter. Conclusions: Digital adaptive noise cancellation, even when limited by electronics noise, can recover pump-probe signals by removal of laser RIN, under conditions where averaging alone fails.

42 ENGINEERING↗
NASA NTRS1979

Helicopter high gain control

High gain control is explored through a design study of the CH-47B helicopter. The plans are designed to obtain the maximum bandwidth possible given the hardware constraints. Controls are designed with modal control theory to specific bandwidths and closed loop mode shapes. Comparisons are made to an earlier complementary filter approach. Bandwidth improvement by removal of limitations is explored in order to establish hardware and mechanization options. Improvements in the pitch axis control system and in the rate gyro sensor noise characteristics in all axes are discussed. The use of rotor state feedback is assessed.

Cunningham, T. B.↗
NASA NTRS1990

Approach to large space structure control system design using traditional tools

This paper illustrates how traditional analysis and design tools can be successfully applied, with insights derived from recent research on control-structure interaction, to preliminary control system design for a large space structure such as the Space Station Freedom. The control system regulates attitude during construction, normal on-orbit operation, reboost, and docking using control-moment gyros and thrusters. The tools include finite-element modeling, model reduction based on modal truncation, single-input/single-output Bode plot design, position and rate feedback, roll-off and phase filter, and simulation. The resulting system is characterized by simple architecture and moderate bandwidth. The large configuration changes during the construction period are handled by gain scheduling.

Chu, P. Y.↗
NASA NTRSDate not supplied

Aeroservoelastic Control Law Development for the Integrated Adaptive Wing Technology Maturation Wind-Tunnel Test

In this paper, a linear quadratic Gaussian (LQG) regulator was applied to a computational aeroservoelastic (ASE) model of the Integrated Adaptive Wing Technology Maturation (IAWTM) wind-tunnel model to demonstrate its effectiveness for active flutter suppression. The aerodynamics within this computational ASE model were solved using unsteady Reynolds-averaged Navier-Stokes (RANS) equations; the structural dynamics of the model were solved using modal analysis. This RANS-based ASE model was used as the plant for the LQG regulator. The Kalman filter and controller used within the LQG regulator were derived from a reduced-order model (ROM) of the RANS-based ASE model. This ROM-based ASE model was generated using system identification techniques. It was shown that the Kalman filter adequately predicted important states of the plant, and that LQG regulator successfully stabilized an aeroelastically unstable plant without exceeding reasonable control surface limitations. All of this was demonstrated using simulation data, and the methods presented here appear feasible for use in the upcoming IAWTM wind-tunnel tests.

Josiah M. Waite↗
NASA NTRS1993

Identification of a second-order mechanical system model from a state space realization

Many system identification algorithms produce models in modern state variable form. When a mechanical system is identified one knows that there must be a model in second order form. In structural dynamics one is interested in either a modal model of the system, or in a model including a mass matrix, stiffness matrix and a damping matrix. In this paper, algorithms are developed that convert a modern state space realization into the above two representations of interest in mechanical systems. The algorithm can be used with any identification methods that produce a modern state variable representation such as the Eigensystem Realization Algorithm (ERA), its modified version by data correlation (ERA/DC), and combinations of these with Observer/Kalman Filter Identification (OKID). An algorithm is developed that allows one to identify the damping matrix in a model representation, so that one determines how near to modal the damping is in the system, and can therefore understand the degree to which the modes are coupled by the damping in the system. A second algorithm produced the mass, damping, and stiffness matrices, given the input and output matrices. It is assumed that the number of sensors (or the number of actuators) is greater than or equal to the number of modes in the system, and it is proved that this is a necessary condition to be able to uniquely identify these matrices. Experience with examples suggests that a singular value truncation involved in these algorithms can help one determine the true system order. This truncation has the benefit of knowledge of the correct form for a mechanical system model, which is not present in the modern control identification algorithm.

Tseng, Dong-Huei↗
NASA NTRS1979

On adaptive modal control of large flexible spacecraft

A recently developed strategy for adaptive sampled-data control of distributed parameter systems based on a plant modal expansion description and modal simultaneous identification and regulation algorithms is presented with frequent reference to the annular momentum control device (AMCD) test example. The requirements of observation spillover reduction and modal eigenvector shape prespecification, which are especially crucial to the proposed adaptive control strategy, are addressed. Individual low pass time filtering of sensed AMCD particle displacements is proposed for observation spillover reduction. A layered scheme incorporating 'eigenvector' shape improvement is outlined to combat the expansion basis prespecification requirement.

Johnson, C. R., Jr.↗
NASA NTRS1989

Adaptive precompensators for flexible-link manipulator control

The application of input precompensators to flexible manipulators is considered. Frequency domain compensators color the input around the flexible mode locations, resulting in a bandstop or notch filter in cascade with the system. Time domain compensators apply a sequence of impulses at prespecified times related to the modal frequencies. The resulting control corresponds to a feedforward term that convolves in real-time the desired reference input with a sequence of impulses and produces a vibration-free output. An adaptive precompensator can be implemented by combining a frequency domain identification scheme which is used to estimate online the modal frequencies and subsequently update the bandstop interval or the spacing between the impulses. The combined adaptive input preshaping scheme provides the most rapid slew that results in a vibration-free output. Experimental results are presented to verify the results.

Tzes, Anthony P.↗
NASA NTRS1990

An experimental modal testing/identification technique for personal computers

A PC-based system for mode shape identification is evaluated. A time-domain modal identification procedure is utilized to identify the mode shapes of a beam apparatus from discrete time-domain measurements. The apparatus includes a cantilevered aluminum beam, four accelerometers, four low-pass filters, and the computer. The method's algorithm is comprised of an identification algorithm: the Eigensystem Realization Algorithm (ERA) and an estimation algorithm called Minimum Model Error (MME). The identification ability of this algorithm is compared with ERA alone, a frequency-response-function technique, and an Euler-Bernoulli beam model. Detection of modal parameters and mode shapes by the PC-based time-domain system is shown to be accurate in an application with an aluminum beam, while mode shapes identified by the frequency-domain technique are not as accurate as predicted. The new method is shown to be significantly less sensitive to noise and poorly excited modes than other leading methods. The results support the use of time-domain identification systems for mode shape prediction.

Roemer, Michael J.↗