Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “methane concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

In situ aerobic methane oxidation rates in a stratified lake

Abstract Microbial aerobic methane oxidation is an important sink for aquatic methane worldwide. Despite its importance to global methane fluxes, few aerobic methane oxidation rates have been obtained in freshwater or marine environments without imposing changes to the microbial community through use of ex situ methods. A novel in situ incubation method for continuous time‐series measurements was used in Jordan Lake, North Carolina, during 2020–2021, to determine reaction kinetics for aerobic methane oxidation rates across a wide range of naturally varying methane (55–1833 nM) and dissolved oxygen (DO; 28–366 μM) concentrations and temperatures (17–30°C). Methane oxidation began immediately at the start of each of 21 incubations and methane oxidation rates were 1 st order with respect to methane. The data density allowed for accurate calculation of 1 st ‐order rate constants,k, that ranged from 0.018 to 0.462 h −1 (R 2 > 0.967). Addition of ammonium (20–45 μM) to natural concentrations ranging from 0.057 to 2.4 μM did not change aerobic methane oxidation rate kinetics, suggesting that the natural population of aerobic methane oxidizers in this eutrophic lake was not nitrogen limited. Values ofkinversely correlated most strongly with initial DO concentrations (R 2 = 0.82) rather than temperature. Values forkincreased with Julian day throughout our sampling period, suggesting seasonal influences on methane oxidation via responses to geochemical changes or shifts in microbial community abundance and composition. These experiments demonstrate a high variability in the enzymatic capacity for 1 st ‐order methane oxidation rates in this eutrophic lake that is tightly and inversely coupled to oxygen concentrations. Measurements of in situ aerobic methane oxidation rate constants allow for the direct quantification and modeling of the microbial community's capacity for methane oxidation over a wide range of natural methane concentrations.

Marine & Freshwater Biology↗
DOE OSTI2026

Dynamics of argon metastables in Ar–CH 4 radio frequency capacitively-coupled plasma: real-time monitoring with neural network-augmented broadband optical emission spectroscopy

In moderate-pressure radio frequency (RF) capacitively coupled plasmas generated in argon–methane mixtures, the density of argon metastable atoms (Ar 1 s 5 ) exhibits a non-monotonic dependence on methane (CH 4 ) concentration. Laser-induced fluorescence (LIF) was used to measure and compare local Ar 1 s 5 densities in Ar and Ar–CH 4 plasmas at 2.6 Torr and RF powers of 17–117 W. The addition of 1% CH 4 increases the metastable density, and 2% CH 4 triggers a strong depletion by an order of magnitude, compared to 1% CH 4 case. This non-monotonic behavior demonstrates the sensitivity of metastable populations to small gas admixtures, which is critical for processes where metastables drive precursor dissociation. For real-time monitoring of metastable population, broadband optical emission spectroscopy (OES) is augmented with a feedforward neural network (NN) to predict Ar s1 5 densities from spectral features. When trained on LIF data, the NN replicates the absolute densities and the dynamic trends of Ar 1 s 5 density variation. The NN-augmented broadband OES approach can be used as a simple and cost-effective tool for tracking Ar metastables in Ar-rich plasmas, facilitating industrial-scale optimization.

Yatom, Shurik [Princeton Plasma Physics Laboratory↗
DOE OSTI2021

Tritiated Sulfur Hexafluoride Disposition Strategies

Tritium (T 2 ) is a radioactive isotope of hydrogen that is produced in nuclear fission reactions and is often used in nuclear fusion reactions and accelerator-based applications for medical isotope production. As a hydrogen isotope, tritium can readily bind to hydroxyl radicals (OH), forming tritiated water (HTO or T 2 0), and to carbon atoms. Tritium decays to helium-3 ( 3 He) via beta-decay with max decay energy of 18.6 keV. While it is not an external radiation hazard, it can be an internal radiation hazard if tritium is inhaled, ingested, or absorbed through the skin. In applications where tritium is handled, tritium confinement is performed using different barriers to minimize releases to the environment. For gaseous (elemental), liquid (oxide), and metal (hydride) tritium, process piping and components provide the primary confinement function. Secondary tritium confinement is typically provided by inert (i.e. non-flammable gases such as nitrogen, argon, or helium) gloveboxes which are connected to a tritium stripper system. Primary tritium confinement barriers typically produce low volumes of high tritium concentrations of tritiated methane from carbon in steels or organic materials along with tritiated water/tritium oxide (e.g. HTO) and tritiated ammonia from reactions with oxygen and nitrogen. Tritium escaping primary confinement into secondary confinement atmospheres (e.g. gloveboxes) produce higher volumes of lower activity contamination than found in process piping. Tritium contamination also occurs by leaks or tritium permeation/diffusion through confinement materials. Tritium from inside primary confinement barriers will diffuse or leak out of the primary confinement barrier and usually into the air, if the system is inside an air hood or ventilated hot cell, or into the secondary confinement (e.g. glovebox) atmosphere which is either exhausted or stripped based on the function of the secondary confinement (glovebox) system. Accelerator based processes for medical isotope production represent an atypical tritium contamination challenge. In medical isotope production, deuterium supply gas is ionized and accelerated to a tritium gas target to produce neutrons that are then used to produce the medical isotopes through additional nuclear fission reactions. To create large voltage differentials for accelerator operations, an electrical insulation medium is needed to prevent or rapidly quench electric discharges. A common electrical insulation medium utilized in accelerator applications is sulfur hexafluoride (SF 6 ) gas. SF 6 has a high dielectric strength and allows for the construction of smaller accelerator systems compared to other electrical insulation mediums such as air or dry nitrogen. Due to tritium permeation/diffusion through accelerator process and confinement materials, there is the possibility that tritium can contaminate the electrical insulation medium of the accelerator. Tritium contaminated SF 6 creates a material without any obvious processes for managing the contamination, reuse, or disposal of the used SF 6 . This document will discuss possible management strategies for tritium contaminated SF 6 for accelerator-based processes for Molybdenum-99 (Mo-99) production.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2022

Porewater Geochemical Assessment of Seismic Indications for Gas Hydrate Presence and Absence: Mahia Slope, East of New Zealand’s North Island

We compare sediment vertical methane flux off the Mahia Peninsula, on the Hikurangi Margin, east of New Zealand’s North Island, with a combination of geochemical, multichannel seismic and sub-bottom profiler data. Stable carbon isotope data provided an overview of methane contributions to shallow sediment carbon pools. Methane varied considerably in concentration and vertical flux across stations in close proximities. At two Mahia transects, methane profiles correlated well with integrated seismic and TOPAS data for predicting vertical methane migration rates from deep to shallow sediment. However, at our “control site”, where no seismic blanking or indications of vertical gas migration were observed, geochemical data were similar to the two Mahia transect lines. This apparent mismatch between seismic and geochemistry data suggests a potential to underestimate gas hydrate volumes based on standard seismic data interpretations. To accurately assess global gas hydrate deposits, multiple approaches for initial assessment, e.g., seismic data interpretation, heatflow profiling and controlled-source electromagnetics, should be compared to geochemical sediment and porewater profiles. A more thorough data matrix will provide better accuracy in gas hydrate volume for modeling climate change and potential available energy content.

03 NATURAL GAS↗
DOE OSTI2020

Chamber Flux and Porewater Concentration of CH4, CO2 and N2O, 2018, Columbia River bank at the Hanford site, WA, USA

This is the corresponding observations data for the paper: Jorge A Villa; Garrett J Smith; Yang Ju; Lupita Renteria; Jordan C Angle; Evan Arntzen; Samuel F Harding; Huiying Ren; Xingyuan Chen; Audrey H Sawyer; Emily B Graham; James C Stegen; Kelly C Wrighton; Gil Bohrer (2020) Methane and nitrous oxide porewater concentrations and surface fluxes of a regulated river. Science of the Total Environment.Greenhouse gas (GHG) emissions from rivers are a critical missing component of current global GHG models. Their exclusion is mainly due to a lack of in-situ measurements and a poor understanding of the spatiotemporal dynamics of GHG production and emissions, which prevents optimal model parametrization. We combined simultaneous observations of porewater concentrations along different beach positions and depths, and surface fluxes of methane and nitrous oxide at a plot scale in a large regulated river during three water stages: rising, falling, and low. Our goal was to gain insights into the interactions between hydrological exchanges and GHG emissions and elucidate possible hypotheses that could guide future research on the mechanisms of GHG production, consumption, and transport in the hyporheic zone (HZ). Results indicate that the site functioned as a net source of methane. Surface fluxes of methane during river water stages at three beach positions (shallow, intermediate and deep) correlated with porewater concentrations of methane. However, fluxes were significantly higher in the intermediate position during the low water stage, suggesting that low residence time increased methane emissions. Vertical profiles of methane peaked at different depths, indicating an influence of the magnitude and direction of the hyporheic mixing during the different river water stages on methane production and consumption. The site acted as either a sink or a source of nitrous oxide depending on the elevation of the water column. Nitrous oxide porewater concentrations peaked at the upper layers of the sediment throughout the different water stages. River hydrological stages significantly influenced porewater concentrations and fluxes of GHG, probably by influencing heterotrophic respiration (production and consumption processes) and transport to and from the HZ. Our results highlight the importance of including dynamic hydrological exchanges when studying and modeling GHG production and consumption in the HZ of large rivers.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Biological conversion of methane to methanol at high H 2 S concentrations with an H 2 S-tolerant methanotrophic consortium

To develop biological biogas to methanol conversion technology without costly hydrogen sulfide (H 2 S) removal, a high H 2 S tolerant methanotrophic consortium (HTMC), was enriched from an anaerobic digester effluent in presence of 5.64 g/m 3 H 2 S in the gas phase. The HTMC can grow stably and produce methanol under conditions with CH 4 /air mixtures containing 5.64 g/m 3 of H 2 S. There is no significant (p>0.05) difference in cell yield or CH 4 to methanol conversion efficiency between trials with different H 2 S concentrations from 0 g/m 3 to 5.64 g/m 3 . Further, under optimal conditions, a cell yield of 0.333 g cells/g CH 4 , a methanol concentration of 0.28 mg/mL, and a CH 4 to methanol conversion efficiency of 0.22 mol/mol were obtained, respectively. Besides methanotrophs (14.85%) and other bacteria, Cyanobacteria were also identified in the HTMC with a high abundancy (32.16%), which could broaden the application of HTMC for simultaneous utilization of CH 4 and CO 2 from raw biogas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Concentration fluctuations and flammability of cryo-compressed hydrogen and methane jets

Compressed hydrogen stored at cryogenic temperatures has a much higher density than room-temperature storage, which enables large-scale hydrogen storage and transport. An understanding of the release of cryogenic hydrogen from pressurized vessels is needed to evaluate the risk and safety concerns with the use of this fuel. Here, the present work extends the analysis of previous experimental studies that measured the gas concentrations of cryo-compressed hydrogen jets and methane jets using a laser Raman scattering diagnostic system. Since the Raman signals are very small, a denoising algorithm was applied to significantly reduce the noise to enable statistical analysis of the data. The transient features of the turbulent jets were characterized by their concentration intermittencies and probability density functions (PDFs). A two-part PDF was developed to predict the bimodal features of the jet concentration distributions. Then, the flammability factors of the cryogenic jets were calculated based on the intermittency and the PDF.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

LaNi x Fe 1–x O 3 as flexible oxygen or carbon carriers for tunable syngas production and CO 2 utilization

The current study reports LaFe 1–x Ni x O 3–δ redox catalysts as flexible oxygen or carbon carriers for CO2 utilization and tunable production of syngas at relatively low temperatures (~700 °C), in the context of a hybrid redox process. Specifically, perovskite-structured LaFe 1–x Ni x O 3–δ with seven different compositions (x = 0.4–1) were prepared and investigated. Cyclic experiments under alternating methane and CO 2 flows indicated that all the samples exhibited favorable reactive performance: CH 4 and CO 2 conversions varied between 85% and 98% and 70–88%, respectively. While H 2 /CO ratio from Fe-rich redox catalysts was ~2.3:1 in the methane conversion step, Ni-rich catalysts produced a concentrated (~ 93.7 vol%) hydrogen stream via methane cracking. The flexibility of LaFe 1–x Ni x O 3–δ to produce syngas (or hydrogen) with tunable compositions was found to be governed by the iron/nickel (Fe/Ni) ratio. Redox catalysts with higher Fe contents act as a lattice oxygen carrier via chemical looping partial oxidation (CLPOx) of methane whereas those with higher Ni contents function as a carbon carrier via chemical looping methane cracking (CLMC) scheme. XRD analysis and temperature-programmed reactions revealed that both types of catalysts involve the formation of La 2 O 3 and Ni 0 /Ni-Fe phases under the methane environment. The ability to re-incorporate La 2 O 3 and Ni/Fe into a perovskite structure gives rise to oxygen-carrying capacity whereas stable Ni 0 or Ni/Fe phases would catalyze methane cracking without lattice oxygen exchange in the reaction cycles. Here, temperature programmed oxidation and Raman spectroscopy indicated the presence of graphitic and amorphous carbon species, which were effectively gasified by CO 2 to produce concentrated CO. Stability tests over LaFe 0.5 Ni 0.5 O 3 and LaNiO 3 revealed that the redox performance was stable over a span of 50 cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Control of hydrogen concentrations by microbial sulfate reduction in two contrasting anoxic coastal sediments

Introduction Molecular hydrogen is produced by the fermentation of organic matter and consumed by organisms including hydrogenotrophic methanogens and sulfate reducers in anoxic marine sediment. The thermodynamic feasibility of these metabolisms depends strongly on organic matter reactivity and hydrogen concentrations; low organic matter reactivity and high hydrogen concentrations can inhibit fermentation so when organic matter is poor, fermenters might form syntrophies with methanogens and/or sulfate reducers who alleviate thermodynamic stress by keeping hydrogen concentrations low and tightly controlled. However, it is unclear how these metabolisms effect porewater hydrogen concentrations in natural marine sediments of different organic matter reactivities. Methods We measured aqueous concentrations of hydrogen, sulfate, methane, dissolved inorganic carbon, and sulfide with high-depth-resolution and 16S rRNA gene assays in sediment cores with low carbon reactivity in White Oak River (WOR) estuary, North Carolina, and those with high carbon reactivity in Cape Lookout Bight (CLB), North Carolina. We calculated the Gibbs energies of sulfate reduction and hydrogenotrophic methanogenesis. Results Hydrogen concentrations were significantly higher in the sulfate reduction zone at CLB than WOR (mean: 0.716 vs. 0.437 nM H 2 ) with highly contrasting hydrogen profiles. At WOR, hydrogen was extremely low and invariant (range: 0.41–0.52 nM H 2 ) in the upper 15 cm. Deeper than 15 cm, hydrogen became more variable (range: 0.312–2.56 nM H 2 ) and increased until methane production began at ~30 cm. At CLB, hydrogen was highly variable in the upper 15 cm (range: 0.08–2.18 nM H 2 ). Ratios of inorganic carbon production to sulfate consumption show AOM drives sulfate reduction in WOR while degradation of organics drive sulfate reduction in CLB. Discussion We conclude more reactive organic matter increases hydrogen concentrations and their variability in anoxic marine sediments. In our AOM-dominated site, WOR, sulfate reducers have tight control on hydrogen via consortia with fermenters which leads to the lower observed variance due to interspecies hydrogen transfer. After sulfate depletion, hydrogen accumulates and becomes variable, supporting methanogenesis. This suggests that CLB’s more reactive organic matter allows fermentation to occur without tight metabolic coupling of fermenters to sulfate reducers, resulting in high and variable porewater hydrogen concentrations that prevent AOM from occurring through reverse hydrogenotrophic methanogenesis.

Microbiology↗
DOE OSTI2025

Source attribution of near-surface ozone pollution in Jiangsu Province of China over 2013–2019

Near-surface ozone (O3) is one of the most severe air pollutants in China, particularly over densely populated Jiangsu Province in the Yangtze River Delta. In this study, an O3 source tagging technique is utilized in a chemistry-climate model to quantify the source contributions of various emission sectors and regions for nitrogen oxides (NOx) and volatile organic compounds (VOCs) to O3 concentrations in Jiangsu Province during 2013–2019. The results show that the near-surface O3 in Jiangsu Province is mainly contributed by surrounding and remote anthropogenic NOx emissions through long-range transport. Local anthropogenic NOx emissions account for only 13 % and 18 % of the annual and summertime mean near-surface O3 in Jiangsu Province, respectively. Anthropogenic NOx emissions from the surface transportation, industry, and energy sectors account for 21 %, 22 % and 20 % of the annual mean near-surface O3 concentration in Jiangsu Province, respectively. Biogenic and anthropogenic VOCs emissions each explains one-third of the annual mean near-surface O3 concentration in Jiangsu, while methane and stratospheric chemical production contribute 21 % and 6 %, respectively. The sources from stratospheric production, aircraft, lightning, and foreign emissions are the primary contributors to O3 in the mid- and high troposphere. During high pollution days in Jiangsu Province, the near-surface O3 concentrations increase with the maximum exceeding 20 ppb, which is attributed to both the enhanced photochemical production and regional transport in favorable meteorological conditions.

ozone pollution↗
DOE OSTI2021

Amines have lower sooting tendencies than analogous alkanes, alcohols, and ethers

While the sooting tendencies of regular hydrocarbons, oxygenates, and complex fuel mixtures have been well-studied, far less research has been devoted to analyzing the influence of fuel-nitrogen on soot formation. The effect of nitrogen on soot formation becomes relevant for diesel fuels with nitrogen-containing additives, as well as biomass or biomass-derived fuels, which can contain up to 30% nitrogen-containing compounds by dry weight. To begin closing these gaps in the literature, the sooting tendencies of 14 C4 and C6 amines were measured. Sooting tendencies were quantified by re-scaling relative soot concentrations measured in fuel-doped methane flames into Yield Sooting Indices (YSI). The relative soot concentrations were measured with line-of-sight spectral radiance, and validation experiments confirmed that the presence of nitrogen in the test compounds did not interfere with this diagnostic. All of these amines had lower sooting tendencies than the structurally analogous hydrocarbons and oxygenates. The sooting tendencies of amine isomers with the same chemical formula varied significantly. Secondary amines with linear substituents were found to offer the lowest sooting propensity, while primary amines with branched substituents were observed to yield the largest sooting tendencies. In conclusion, the relationship between sooting propensity and chemical structure of the amines hints at the complex nature of soot formation, and highlights an interesting and unexplored area of combustion chemistry for further studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Stable isotopes of carbon dioxide (CO2), dissolved inorganic carbon (DIC), water and concentrations of greenhouse gases in a mountainous watershed (Crested Butte, Colorado)

Temperature and precipitation variability in response to climate change affects water cycling of watersheds and can potentially impact water quality, water availability, elemental and molecular fluxes, and biogeochemical processes. Here we report the measurements of light stable isotopes and greenhouse gases analysis to a large multidisciplinary project addressing watershed function. Water hydrogen (H) and oxygen (O) stable isotopes of snow and water saturated soil were measured to constrain source contributions to groundwater and streamflow. In an effort to better constrain existing nitrogen and carbon cycling models in high-altitude ecosystems, carbon dioxide (CO2), nitrous oxide (N2O), methane (CH4) greenhouse gases concentrations and stable isotope signatures of CO2, dissolved inorganic carbon (DIC), and water were measured. This dataset includes one CSV file and one Excel file containing data including stable isotopes of carbon dioxide (CO2), dissolved inorganic carbon (DIC), water and concentrations of greenhouse gases. The CSV and Excel files contain the same information/data but have included both versions for accessibility.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Model simulations of Plum Island Ecosystems LTER low marsh site using ELM-PFLOTRAN

Model simulations using the E3SM Land Model (ELM) coupled to the PFLOTRAN reactive transport model via the Alquimia interface. The simulations were conducted for a tidal salt marsh at the Plum Island Ecosystems LTER near Rowley, Massachusetts, USA. Model simulations were forced using site-specific tidal cycles and salinity, and the simulations used a biogeochemical reaction network including aerobic decomposition, sulfate reduction, iron reduction, and methanogenesis. Model outputs include simulated carbon stocks, carbon dioxide and methane fluxes, and porewater concentrations of key solutes related to sulfur, iron, and carbon cycling. The model simulations included a saline simulation (with tidal sulfate inputs), a fresh simulation (with low salinity and low sulfate inputs), and a saline simulation with lower vegetation productivity to represent the effect of salinity on vegetation. These simulations were conducted to demonstrate that a new model framework incorporating subsurface redox and biogeochemical interactions into a land surface model could reproduce measured surface greenhouse gas fluxes and biogeochemical dynamics in tidal marsh ecosystems, and to test whether including redox interactions in a land surface model would allow the model to resolve contrasts in biogeochemical cycling and greenhouse gas production between saline and freshwater wetlands.The data package includes gzipped tar archives (which can be expanded using standard tar and gzip utilities) of model outputs from three model configurations: saline subsurface and reduced vegetation productivity related to salinity; saline subsurface with vegetation productivity not reduced; and freshwater. Also included are code for the modified E3SM model, Alquimia interface, and PFLOTRAN reactive transport simulator in gzipped tar format; plain text parameter and configuration files; python code files for visualizing model output and defining model configurations; and model output, tide and salinity forcing, and configuration files in netCDF format. See the README.md file in the data package for a detailed description of all files contained in the package. All files are in netCDF (.nc), gzipped tar archive (.tar.gz or .tgz), or text (all other files).Updated: May 13, 2024. Model output, E3SM code, PFLOTRAN input files, and python codes for visualizing results were updated to reflect changes made for the manuscript revision. The updated archive reflects the code and model output from the final accepted manuscript. Changes included updated reaction parameters reflecting improved parameterization and additional comparisons with field measurements. E3SM code changes included better support for multiple grid cells and improved flow and transport parameterization.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Mitigation of ventilation air methane (VAM) using novel methanotrophic coating materials: a technical analysis

Abstract Ventilation air methane (VAM) is a potent greenhouse gas source originating from geological wells, current and extinct mineshafts and other terrestrial conduits venting methane to the atmosphere, contributing to global methane emissions and disproportionate warming potential. Herein, we introduce the concept of the methanotrophic material as an engineering solution. Such materials should be capable of converting methane at ambient temperatures and pressures to a binder product, capturing and permanently sequestering the methane while simultaneously restricting its further emission. While such materials are currently under research development, this goal is supported and facilities by the mathematical framework, introduced and used herein, to evaluate the ability to convert methane, using currently published activity data. We include a case study of the conversion of a characteristic stream of VAM (0.6% methane in air, 1.7 × 10 8 l hr −1 equivalent to 100 000 standard cubic feet per minute). We show that when appropriately designed, such systems require a surface coverage of less than 1000 m of mine tunnel length (equivalent to 20 000 m 2 areal coverage) in order to reduce the methane emission from this stream by over 99%. Finally, we highlight formaldehyde as a reactive intermediate of methane oxidation which may itself be incorporated into these coating materials. As a component of binders and polymers already used ubiquitously in commercial products, this intermediate ultimately allows these systems to sequester the carbon from methane in a stable and solid form. The results presented here are easily extended to the treatment of other methane streams—either more concentrated or dilute—and the results herein will guide the design and development of a new class of carbon-negative materials.

Environmental Sciences & Ecology↗
DOE OSTI2026

Dataset for Cruz-O'Byrne et al (2026): "Divergent biogeochemical responses in upland coastal forest soils to repeated flooding and shifts in water chemistry"

Hydrologic disturbances from accelerated sea-level rise and the increasing frequency and intensity of storms and tidal flooding are altering biogeochemical processes in upland coastal forests, transforming these ecosystems into wetlands. However, the initial effects of flooding on belowground biogeochemistry and the mechanisms driving greenhouse gas dynamics and soil organic matter stability during the early stages of this transition remain poorly understood. This dataset presents the results of a mesocosm experiment conducted in a controlled, highly instrumented laboratory environment, in which freshwater and brackish water pulses were applied to intact soil monoliths from a temperate upland coastal forest to examine how floodwater chemistry influences soil biogeochemistry and organo-mineral interactions. All data files are plain-text CSV (comma-separated value), and no special software is required to read them. Details about the content of each file are available in the document “Dataset_readme”. The dataset consists of the following data: • rcruzobyrne_moisture: Soil volumetric water content (VWC) • rcruzobyrne_GHG: Headspace greenhouse gas (GHG) concentration and fluxes • rcruzobyrne_methane_isotopes: Headspace methane isotope signature • rcruzobyrne_porewater: Porewater chemistry • rcruzobyrne_CDOM: Porewater colored dissolved organic matter (CDOM) • rcruzobyrne_FTIR: Soil Fourier-transform infrared (FTIR) spectroscopy Details of the experimental setup, data collection, and data analysis are provided in the manuscript by Cruz-O’Byrne et al (2026) Divergent biogeochemical responses in upland coastal forest soils to repeated flooding and shifts in water chemistry. Biogeochemistry. https://doi.org/10.1007/s10533-026-01340-0

EARTH SCIENCE > ATMOSPHERE > GREENHOUSE GAS↗
DOE OSTI2021

SPRUCE Outflow Chemistry Data for Experimental Plots Beginning in 2016

This data set includes the chemistry of outflow waters in the SPRUCE experiment plots located in the S1 bog of the USDA Forest Service Marcell Experimental Forest (MEF) in northern Minnesota, 40 km north of Grand Rapids. These data are post-treatment data from the warming and elevated carbon dioxide (CO2) treatments associated with the SPRUCE experiment. There are ten experimental plots in SPRUCE: five temperature treatments (+0, +2.25, +4.5, +6.75, +9°C) at ambient CO2, and the same five temperature treatments at elevated CO2 (+500 ppm). Sample collection and analyses started in March of 2016 and will continue for the duration of the experiment. Samples were analyzed for pH, specific conductivity, anion concentrations (chloride, sulfate), cation concentrations (calcium, potassium, magnesium, sodium, aluminum, iron, manganese, silicon, strontium), nutrient concentrations (ammonium, nitrate, soluble reactive phosphorus, total nitrogen, total phosphorus), and total organic carbon (TOC) concentrations. Subsets of the samples have been analyzed for natural-abundance stable isotopes of water (δ18O-H2O and δD-H2O), dissolved carbon dioxide (δ13C-CO2), and dissolved methane (δ13C-CH4), and concentrations of total mercury (Thg), methylmercury (MeHg), ferrous iron (Fe2+), ferric iron (Fe3+), dissolved inorganic carbon (DIC), and dissolved methane (CH4).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Neutron imaging of hydrogenous gases in porous-carbon materials around phase transitions

Focus herein is on hydrogenous gases interacting with porous-carbon materials on activated biochar at pressures ranging from 0 to 100 bar and temperatures from room (ambient) to cryogenic. Neutron radiography was conducted using a custom-made cell system to simultaneously image pure gas and gas interacting with the porous carbon. From neutron attenuation, the cross sections of methane and ethane and number concentrations were determined for different pressures and temperatures and compared with corresponding reference data. Sorption properties of the porous materials were investigated in situ with methane, ethane, and propane.

Ossler, Frederik [Lund University, Sweden]↗
DOE OSTI2023

Biological methane production and accumulation under sulfate-rich conditions at Cape Lookout Bight, NC

Introduction: Anaerobic oxidation of methane (AOM) is hypothesized to occur through reverse hydrogenotrophic methanogenesis in marine sediments because sulfate reducers pull hydrogen concentrations so low that reverse hydrogenotrophic methanogenesis is exergonic. If true, hydrogenotrophic methanogenesis can theoretically co-occur with sulfate reduction if the organic matter is so labile that fermenters produce more hydrogen than sulfate reducers can consume, causing hydrogen concentrations to rise. Finding accumulation of biologically-produced methane in sulfate-containing organic-rich sediments would therefore support the theory that AOM occurs through reverse hydrogenotrophic methanogenesis since it would signal the absence of net AOM in the presence of sulfate. Methods: 16S rRNA gene libraries were compared to geochemistry and incubations in high depth-resolution sediment cores collected from organic-rich Cape Lookout Bight, North Carolina. Results: We found that methane began to accumulate while sulfate is still abundant (6–8 mM). Methane-cycling archaea ANME-1, Methanosarciniales, and Methanomicrobiales also increased at these depths. Incubations showed that methane production in the upper 16 cm in sulfate-rich sediments was biotic since it could be inhibited by 2-bromoethanosulfonoic acid (BES). Discussion: We conclude that methanogens mediate biological methane production in these organic-rich sediments at sulfate concentrations that inhibit methanogenesis in sediments with less labile organic matter, and that methane accumulation and growth of methanogens can occur under these conditions as well. Our data supports the theory that H2 concentrations, rather than the cooccurrence of sulfate and methane, control whether methanogenesis or AOM via reverse hydrogenotrophic methanogenesis occurs. We hypothesize that the high amount of labile organic matter at this site prevents AOM, allowing methane accumulation when sulfate is low but still present in mM concentrations

59 BASIC BIOLOGICAL SCIENCES↗