Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Adding Realism to Nuclear Material Dissolving Analysis

Two new criticality modeling approaches have greatly increased the efficiency of dissolver operations in H-Canyon. The first new approach takes credit for the linear, physical distribution of the mass throughout the entire length of the fuel assembly. This distribution of mass is referred to as the linear density. Crediting the linear density of the fuel bundles results in using lower fissile concentrations, which allows higher masses to be charged to the dissolver. Also, this approach takes credit for the fact that only part of the fissile mass is wetted at a time. There are multiple assemblies stacked on top of each other in a bundle. On average, only 50-75% of the mass (the bottom two or three assemblies) is wetted at a time. This means that only 50-75% (depending on operating level) of the mass is moderated and is contributing to the reactivity of the system. The second new approach takes credit for the progression of the dissolving process. Previously, dissolving analysis looked at a snapshot in time where the same fissile material existed both in the wells and in the bulk solution at the same time. The second new approach models multiple consecutive phases that simulate the fissile material moving from a high concentration in the wells to a low concentration in the bulk solution. This approach is more realistic and allows higher fissile masses to be charged to the dissolver.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Expanded Materials Degradation Analysis (EMDA) Volume 3: Aging of Reactor Pressure Vessels

In NUREG/CR-6923 ORNL/TM-2013/532, "Expert Panel Report on Proactive Materials Degradation Assessment," referred to as the PMDA report, NRC conducted a comprehensive evaluation of potential aging-related degradation modes for core internal components, as well as primary, secondary, and some tertiary piping systems, considering operation up to 40 years. This document has been a very valuable resource, supporting NRC staff evaluations of licensees' aging management programs and allowing for prioritization of research needs.This report describes an expanded materials degradation assessment (EMDA), which significantly broadens the scope of the PMDA report. The analytical timeframe is expanded to 80 years to encompass a potential second 20-year license-renewal operating-period, beyond the initial 40-year licensing term and a first 20-year license renewal. Further, a broader range of structures, systems, and components (SSCs) was evaluated, including core internals, piping systems, the reactor pressure vessel (RPV), electrical cables, and concrete and civil structures. The EMDA uses the approach of the phenomena identification and ranking table (PIRT), wherein an expert panel is convened to rank potential degradation scenarios according to their judgment of susceptibility and current state of knowledge.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Random Forest Prediction of Crystal Structure from Electron Diffraction Patterns

Transmission electron microscopy (TEM) diffraction patterns are regularly used to determine the structure of crystalline materials. Electron diffraction is the most common method to solve for unknown or partially known crystal structures, as it provides direct and interpretable feedback on the orientation of crystal grains under the beam [1]. However, it remains a challenge to determine the crystal structure of a new material or even a new phase of an existing material. Analysis of such materials commonly requires manual exploration and comparison with simulated diffraction patterns. This is often a time consuming process with no obvious start point when many similar structures are possible, and this method cannot be used to determine crystal structure or orientation from structures not included in the diffraction libraries. Therefore, we have developed a machine learning model to determine the crystal structure of a material from its electron diffraction pattern.

36 MATERIALS SCIENCE↗

Fusion-Driven Subcritical System FDS-SFB and Its Blanket Materials Activation Analysis

Fusion-fission hybrid reactor is a bridge between fusion and fission nuclear energy and it is a solution to overcome difficulties of fission energy development with the features of energy production, fuel breeding and waste transmutation. Many researches on fusion-fission hybrid reactor have been done in last decades. Fusion Driven Subcritical Spent Fuel Burning System (FDS-SFB) was proposed as an intermediate step toward the final application of fusion energy and designed to transmute the long-lived nuclear wastes from fission power plants and to produce fissile nuclear fuels for feeding fission power plants. The design of FDS-SFB is based on relatively easy-achieved plasma parameters extrapolated form the successful operation of the experimental advanced superconducting Tokamak (EAST) in China and other tokamaks in the world, and the subcritical blanket is designed based on the well-developed technologies of fission reactor. Materials activation characteristic is one of the key issues for hybrid reactor research. The activation of materials would substantially influence not only the safety of the reactors but also the recycling of used reactor materials. The selection of materials is very important to control the neutron-induced activation on fusion reactor as well as to ensure the attractiveness of fusion-fission nuclear power regarding safety and environmental aspects. The reduced activation ferritic-martensitic (CLAM) steel is preliminarily considered as the candidate structural materials for FDS-SFB. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Evaluation of Compton suppression for enhancing trace element identification in neutron activation analysis of reference materials

Neutron activation analysis (NAA) is a powerful technique for identifying and quantifying trace elements in materials. However, challenges such as high dead times, spectral interferences, and high Compton continuum often arise. This study employs a Compton suppression system (CSS) to enhance NAA sensitivity by reducing the Compton continuum, thereby improving the peak-to-Compton ratio. National Institute of Standards and Technology certified reference materials 1632d, 1633c, and Canadian National Research Council TORT-1 were irradiated in a thermal and epithermal neutron flux under various irradiation, decay and counting times and analyzed using high-resolution gamma-ray spectroscopy with and without Compton suppression. The reduction factor was calculated to evaluate the effectiveness of the CSS, demonstrating significant background reduction and improved detection limits for trace elements. Additional experiments with a 137Cs point source demonstrated the impact of detector-source geometry on system performance, showing a decrease in the reduction factor as the source was moved further from the NaI detector. An optimum distance between the source and HPGe detector was observed, yielding the highest peak-to-Compton ratio. The results highlight the CSS's ability to minimize spectral interference and enhance elemental identification.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Sensitivity Analysis of Material Model Parameters to Reproduce Crushing of Composite Tubes

The ability to predict the behavior of composite structures under impact conditions is an important challenge for engineering analysis since it requires modeling beyond the elasticity and into failure initiation and propagation. Crushing of laminate composites is the result of a combination of several and complex failure mechanisms, which are not always possible to reproduce together in a single finite element analysis (FEA). In this paper, models based on lamina-level failure criteria have been used to predict the onset of damage; once failure initiates, the mechanisms of failure propagation require reducing the material properties using several degradation schemes. Among the composite material models available in LS-DYNA, MAT-ENHANCED-COMPOSITE-DAMAGE (MAT-54) has been chosen for modeling the axial crushing of composite tubes with various resistant sections and wall slope, given the reduced experimental input parameters to insert into the card definition. Comparison with experimental data shows that such material model is able to successfully reproduce the crushing behavior, even if the numerical results are strictly correlated with some model parameters which cannot be measured experimentally or are purely mathematical expedients. Therefore, extensive calibration of these parameters by trial-and-error is necessary to achieve successful simulation results. Once done it for a structure made of the same composite material, it is possible to adopt the same card configuration for all the other cases, obtaining good agreement between numerical and experimental results. After, the attempt to model the same geometries using the MAT-LAMINATED-COMPOSITE-FABRIC (MAT-58) card with the same parameter values previously calibrated has been done obtaining results comparable with the experimental data.

36 MATERIALS SCIENCE↗

Neutron Resonance Spectroscopy for the Analysis of Materials and Objects

The presence of resonances in neutron induced reaction cross sections is the basis of the Neutron Resonance Capture (NRCA) and Transmission (NRTA) Analysis techniques. Since resonances can be observed at neutron energies which are specific for each nuclide, they can be used as fingerprints to identify and quantify elements in materials and objects. Both NRCA and NRTA are fully non-destructive methods which determine the bulk elemental composition, do not require any sample preparation and result in a negligible residual activation. In this text we review the technique and present an analysis procedures including one based on a more methodological approach which relies on a full Resonance Shape Analysis (RSA) and accounts directly for the neutron self-shielding, multiple scattering, Doppler broadening and instrumental resolution.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Characterization of Shallow, Undoped Ge/SiGe Quantum Wells Commercially Grown on 8-in. (100) Si Wafers

Hole spins in Ge quantum wells have shown success in both spintronic and quantum applications, thereby increasing the demand for high-quality material. We performed material analysis and device characterization of commercially grown shallow and undoped Ge/SiGe quantum well heterostructures on 8-in. (100) Si wafers. Material analysis reveals the high crystalline quality, sharp interfaces, and uniformity of the material. We demonstrate a high mobility (1.7 × 10 5 cm 2 V –1 s –1 ) 2D hole gas in a device with a conduction threshold density of 9.2 × 10 10 cm –2 . We study the use of surface preparation as a tool to control barrier thickness, density, mobility, and interface trap density. We report interface trap densities of 6 × 10 12 eV –1 . Our results validate the material’s high quality and show that further investigation into improving device performance is needed. We conclude that surface preparations which include weak Ge etchants, such as dilute H 2 O 2 , can be used for postgrowth control of quantum well depth in Ge-rich SiGe while still providing a relatively smooth oxide–semiconductor interface. Our results show that interface state density is mostly independent of our surface preparations, thereby implying that a Si cap layer is not necessary for device performance. Transport in our devices is instead limited by the quantum well depth. Commercially sourced Ge/SiGe, such as studied here, will provide accessibility for future investigations.

36 MATERIALS SCIENCE↗

Lithium Intercalation in Core-Shell Materials-Theoretical Analysis

Core-shell composite structures are potential candidates for Li-ion battery electrodes as they can take advantage of materials with higher energy density and materials with higher cyclability. This paper derives an analytical solution for isotropic 1-dimensional diffusion with galvanostatic boundary condition in composite slab, cylinder and sphere using separation of variables method. A general interfacial condition has been used to represent the dynamics at the interface of the composite material rendering the solution useful for wide variety of battery materials. Using the derived analytical solution for diffusion, intercalation induced stresses were estimated for spherical core-shell materials. (C) 2014 The Electrochemical Society. All rights reserved.

Suthar, B↗

Analysis of material recovery facilities for use in life-cycle assessment

Highlights: • Life-cycle assessment of solid waste management relies on accurate process models. • Material recovery facility (MRF) processes were modeled with new primary data. • Single stream, dual stream, pre-sorted, and mixed waste MRFs were considered. • MRF electricity consumption ranges from 4.7 to 7.8 kW h per Mg input. • Total cost ranges from $19.8 to $24.9 per Mg input. - Abstract: Insights derived from life-cycle assessment of solid waste management strategies depend critically on assumptions, data, and modeling at the unit process level. Based on new primary data, a process model was developed to estimate the cost and energy use associated with material recovery facilities (MRFs), which are responsible for sorting recyclables into saleable streams and as such represent a key piece of recycling infrastructure. The model includes four modules, each with a different process flow, for separation of single-stream, dual-stream, pre-sorted recyclables, and mixed-waste. Each MRF type has a distinct combination of equipment and default input waste composition. Model results for total amortized costs from each MRF type ranged from $19.8 to $24.9 per Mg (1 Mg = 1 metric ton) of waste input. Electricity use ranged from 4.7 to 7.8 kW h per Mg of waste input. In a single-stream MRF, equipment required for glass separation consumes 28% of total facility electricity consumption, while all other pieces of material recovery equipment consume less than 10% of total electricity. The dual-stream and mixed-waste MRFs have similar electricity consumption to a single-stream MRF. Glass separation contributes a much larger fraction of electricity consumption in a pre-sorted MRF, due to lower overall facility electricity consumption. Parametric analysis revealed that reducing separation efficiency for each piece of equipment by 25% altered total facility electricity consumption by less than 4% in each case. When model results were compared with actual data for an existing single-stream MRF, the model estimated the facility’s electricity consumption within 2%. The results from this study can be integrated into LCAs of solid waste management with system boundaries that extend from the curb through final disposal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

RAPID: The Development and Application of a Hybrid High Pressure Ion Chromatography and Inductively Coupled Plasma Mass Spectrometry Method for the Direct Analysis of Irradiated Materials

RAPID (Rapid Analysis of Post-Irradiation Debris) is an automated online separation–direct analysis method developed at Oak Ridge National Laboratory (ORNL) to measure both radioactive and stable fission isotopes by mass. Developed to measure the concentration and isotopic composition of over 40 elements down to the femtogram level, RAPID demonstrates the sensitivity, stability, and precision required to achieve accurate, low-level analyses of elements of non-natural origin. The application of the RAPID method to silica- and soil-based matrices achieved complete matrix exclusion and direct online analysis of the elementally separated analytes, yielding precise isotopic compositions. When combined with isotope dilution, this approach yielded elemental concentrations with low uncertainties, providing a rapid analytical method that encompasses group I and II metals, transition metals, refractory metals, platinum group metals, lanthanides, and actinides. The robustness, sensitivity, reproducibility, and numerous applications to a number of fields in nuclear measurements have been confirmed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advanced In-situ Diagnostics for Multicomponent Gas Analysis and Material Aging

Current methods of detecting material aging rely heavily on accelerated aging studies expensive, bulky, and resource-hungry diagnostics. We are developing compact gas analysis methods based on sensor platforms such as quartz crystal microbalances (QCM), using nanoporous metals and Metal-Organic Frameworks (MOFs), which enhance sensitivity and impart selectivity to analytes. Targeted analytes are O2 and other volatile analytes. In FY16 we installed and tested a new QCM system coupled to a commercial gas mixing system. This instrumentation provides a new multi-use capability that: 1) allows evaluation of detection of novel materials to enable selective detection of volatile species relevant to Enhanced Surveillance; 2) accelerates development of new thin film deposition methods for depositing these materials on sensing devices; and 3) enables in-situ monitoring, with sub-monolayer sensitivity, of the interaction of volatile species with material surfaces subject to aging or corrosion.

36 MATERIALS SCIENCE↗

Analysis of Material Properties of Aged Rigid Polyurethane Foam

Polyurethane foams are organic materials which can be classified as mechanically rigid or flexible. They are chemically inert, relatively unaffected by the presence of water (cracking, swelling, absorption), and can be manufactured in densities from 3-40 lb/ft 3 . In addition, polyurethane foams have exceptional mechanical and thermal properties, which support use of polyurethane foams in the 9977 shipping packages. These packages are designed for shipment of special nuclear material and are approved for storage in the K-area complex (KAC) at Savannah River Site. Through the analysis of conditioned foams, a service life ofFR-3700 can be estimated for the storage of the 9977 packages. Thus, considering anticipated temperatures of the 9977 packages in the KAC, FR-3700 was conditioned at 160°F, 185°F, 215°F, 250°F, and 160°F with 50% relative humidity, which remains within the service temperature of-320°F - 250°F of the FR-3700 foam in the 9977 packages. Prior studies have analyzed foams after 7, 20, and 30 months of conditioning with the current study analyzing foams up to 55 months of conditioning. Considering the limited information on the effects of radiation on FR-3700, samples were irradiated with a cobalt-60 source at a high and low dose rate of 90.9 krad/hr and 16.67 krad/hr, respectively, to examine the effects of irradiation and dose rate on thermal properties. It was found that foams conditioned up to 55 months had comparable heat capacity values to FR-3700, with a slight increase due to humidity. Results suggest that fire additives began decomposing at higher conditioning temperatures, reducing the average percent mass loss. Overall, irradiation and humidity had minimal effects on thermal properties of FR-3700.

36 MATERIALS SCIENCE↗

Secondary Ion Mass Spectrometry Analysis of Materials to Develop In-core Safeguards Reactor Monitoring Devices

During reactor operations and fuel burn up, some isotopic abundances change due to nuclear reactions and provide sensitive indicators of neutron fluence and fuel burnup. Secondary ion mass spectrometry (SIMS) analysis has been used to directly measure isotope ratios of selected impurity elements in irradiated nuclear reactor materials. Direct in situ SIMS measurements were made in graphite and metal samples, following shaping and surface cleaning. Other elements such as Be must be chemically separated and purified prior to SIMS analyses. Elements such as pre-existing impurity U and Pu produced from the U, are in low abundance and must also be chemically separated and are measured by thermal ionization mass spectrometry (TIMS). Studies combining SIMS and TIMS analyses demonstrate the value of this approach in determining reactor fluence profiles, power production, and other parameters. Future work proceeding from this analytical work will include developing monitoring devices designed for relatively easy placement and retrieval in a reactor, and direct SIMS analyses after exposure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Process Design and Techno-economic Analysis for Materials to Treat Produced Waters

Significant quantities of water are produced during enhanced oil recovery making these “produced water” streams attractive candidates for treatment and reuse. However, high concentrations of dissolved silica raise the propensity for fouling. In this paper, we report the design and economic analysis for a new ion exchange process using calcined hydrotalcite (HTC) to remove silica from water. This process improves upon known technologies by minimizing sludge product, reducing process fouling, and lowering energy use. Process modeling outputs included raw material requirements, energy use, and the minimum water treatment price (MWTP). Monte Carlo simulations quantified the impact of uncertainty and variability in process inputs on MWTP. These analyses showed that cost can be significantly reduced if the HTC materials are optimized. Specifically, R&D improving HTC reusability, silica binding capacity, and raw material price can reduce MWTP by 40%, 13%, and 20%, respectively. Optimizing geographic deployment further improves cost competitiveness.

04 OIL SHALES AND TAR SANDS↗

Applications of laser produced ion beams to nuclear analysis of materials

Laser produced ion beams have unique characteristics which are ultra-short pulse, very low emittance, and variety of nuclear species. These characteristics could be used for analyzing various materials like low Z ion doped heavy metals or ceramics. Energies of laser produced ion beam extend from 0.1MeV to 100MeV. Therefore, various nuclear processes can be induced in the interactions of ion beams with samples. The ion beam driven nuclear analysis has been developed for many years by using various electrostatic accelerators. To explore the applicability of laser ion beam to the analysis of the Li ion battery, a proton beam with the diameter of {approx} 1.0 {mu}m at Takasaki Ion Acceleration for Advanced Radiation Application (TIARA), JAEA was used. For the analysis, the PIGE (Particle-Induced Gamma Ray Emission) is used. The proton beam scans over Li battery electrode samples to diagnose Li density in the LiNi{sub 0.85}Co{sub 0.15}O{sub 2} anode. As the results, PIGE images for Li area density distributions are obtained with the spatial resolution of better than 1.5{mu}m FWHM. By the Li PIGE images, the depth dependence of de-intercalation levels of Li in the anode is obtained. By the POP experiments at TIARA, it is clarified that laser produced ion beam is appropriate for the Li ion battery analysis. 41.85.Lc, 41.75.Jv, 42.62.cf.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

AGC 2 Irradiated Material Properties Analysis

The Advanced Reactor Technologies Graphite Research and Development Program is conducting an extensive graphite irradiation experiment to provide data for licensing of a high temperature reactor (HTR) design. In past applications, graphite has been used effectively as a structural and moderator material in both research and commercial high temperature gas cooled reactor designs. , Nuclear graphite H 451, used previously in the United States for nuclear reactor graphite components, is no longer available. New nuclear graphite grades have been developed and are considered suitable candidates for new HTR reactor designs. To support the design and licensing of HTR core components within a commercial reactor, a complete properties database must be developed for these current grades of graphite. Quantitative data on in service material performance are required for the physical, mechanical, and thermal properties of each graphite grade, with a specific emphasis on data accounting for the life limiting effects of irradiation creep on key physical properties of the HTR candidate graphite grades. Further details on the research and development activities and associated rationale required to qualify nuclear grade graphite for use within the HTR are documented in the graphite technology research and development plan.

36 MATERIALS SCIENCE↗