SEARCH · Engineering Papers

Results for “low-loss”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Radiative transfer theory for active remote sensing of half-space random media

In active remote sensing of low-loss and scattering-dominant areas, the effect of volume scattering can be modeled as a half-space random medium with lateral and vertical fluctuations. Correlation functions are assumed to be Gaussian laterally and exponential vertically. A radiative transfer theory is developed in this paper to calculate backscattering cross sections. An iteration process is used. When calculated to first order in albedo, the result gives the single-scattering effects and confirms previous work. Calculated to second order, it is found that the backscattered power exhibits depolarization effects. This important consequence is studied numerically by illustrating the backscattering cross sections as a function of incidence angles and frequencies.

Tsang, L.↗

NASA NTRS1979

Fiber optic rotation sensor /FORS/ signal detection and processing

The recent development of low-loss single-mode optical fiber waveguides for light has made possible a new class of inertial reference devices built on the principle of a closed loop interferometer. Light circulating through the loop in both directions experiences a relative phase delay proportional to rotation rate about the loop axis. This paper derives the phase delay and discusses signal detection, signal processing techniques and error sources. It is concluded that synchronous modulation and demodulation and an active gain control at the signal calculation level are required to eliminate drift errors. Potential performance is extraordinarily good; rotation rate sensitivity of a few milli-arc seconds per second and angular position random walk errors of an arc second per square root hour appear feasible.

Goss, W. C.↗

NASA NTRS1979

Design of elastomer dampers for a high-speed flexible rotor

This paper describes the methods used to design elastomerically damped supports for high-speed, flexible rotor-bearing systems. The procedure consists of using a damped natural frequency analysis to identify stiffness and damping requirements for the supports over the speed range. Optimum values for these coefficients are found and unbalance response analysis is used to calculate expected rotor behavior. Equations for calculating the shear and compressive stiffness and damping of button-type elastomer mounts are given, as is a procedure for their application to the design of the elastomeric mounts. These techniques were successfully applied to the design of damped elastomeric supports for a high-speed rotor, which traverses two bending critical speeds. Results of the testing showed that the rotor was well behaved and showed linear response to unbalance. Measured modal damping exceeded expectations and tests were conducted with both high- and low-loss elastomers, enabling the exploration of the practical range of elastomer damping capability.

Tecza, J. A.↗

NASA NTRS1979

Small solar thermal electric power plants with early commercial potential

Cost-effective small solar thermal electric power plants (1- to 10-MW nominal size) offer an attractive way of helping the world meet its future energy needs. The paper describes the characteristics of a conceptual near-term plant (about 1 MW) and a potential 1990 commercial version. The basic system concept is one in which steam is generated using two-axis tracking, parabolic dish, and point-focusing collectors. The steam is transported through low-loss piping to a central steam turbine generator unit where it is converted to electricity. The plants have no energy storage and their output power level varies with the solar insolation level. This system concept, which is firmly based on state-of-the-art technology, is projected to offer one of the fastest paths for U.S. commercialization of solar thermal electric power plants through moderate technology advances and mass production.

Jones, H. E.↗

NASA NTRS1980

Saturn's rings - 3-mm observations and derived properties

Three-millimeter Saturn observations, obtained from 1965 through 1977 and with Jupiter as a reference, have been used to derive a ring brightness temperature of 18 + or - 8 K. The brightness temperature of the disk of Saturn is 156 + or - 9 K. Part of the ring brightness (approximately 6 K) may be accounted for as disk emission which is scattered from the rings; the remainder (12 + or - 8K) is attributed to ring particle thermal emission. Because this thermal component brightness temperature is so much less than the particle physical temperature, limits are placed on the mean size and composition of the ring particles. In particular, as found by others, the particles cannot be rocky, but must be either metallic or composed of extremely low-loss dielectric material such as water ice. If the particles are pure water ice, for example, then a simple slab model and a multiple-scattering model both give upper limits to the particle sizes of approximately 1 m, a value three times smaller than previously available. The multiple-scattering model gives a particle single-scattering albedo at 3 mm of 0.83 + or - 0.13.

Epstein, E. E.↗

NASA NTRS1981

Radiative transfer theory for active remote sensing of a homogeneous layer containing spherical scatterers

The radiative transfer theory with a Rayleigh scattering model is used to study the effect of volume scattering for active microwave remote sensing of low-loss and scattering dominant areas by obtaining backscattering cross sections through iterative and numerical approaches. The iterative approach gives closed form solutions which are valid when the effect of scattering is small. The depolarization of the backscattered power is shown to be a second-order effect. For the general cases, a numerical approach is used to solve the radiative transfer equations. The theoretical results are compared and illustrated for the various cases.

Shin, R. T.↗

NASA NTRS1981

Molybdenum-tin as a solar cell metallization system

The operations of solar cell manufacture are briefly examined. The formation of reliable, ohmic, low-loss, and low-cost metal contacts on solar cells is a critical process step in cell manufacturing. In a commonly used process, low-cost metallization is achieved by screen printing a metal powder-glass frit ink on the surface of the Si surface and the conductive metal powder. A technique utilizing a molybdenum-tin alloy for the metal contacts appears to lower the cost of materials and to reduce process complexity. The ink used in this system is formulated from MoO3 with Sn powder and a trace amount of titanium resonate. Resistive losses of the resulting contacts are low because the ink contains no frit. The MoO3 is finally melted and reduced in forming gas (N2+H2) to Mo metal. The resulting Mo is highly reactive which facilitates the Mo-Si bonding.

Boyd, D. W.↗

NASA NTRS1980

SPS solid state antenna power combiner

Solid state dc-rf converters offer potential improvements in reliability, mass and low voltage operation, provided that anticipated efficiencies in excess of 80 percent can be realized. Field effect transistors offer the greatest potential in the SPS frequency band at 2.45 GHz. To implement this approach it is essential that means be found to sum the power of many relatively low power solid state sources in a low-loss manner, and that means be provided to properly control the phase of the outputs of the large number of solid state sources required. To avoid the power combining losses associated with circuit hybrids it was proposed that the power from multiple solid state amplifiers be combined by direct coupling of each amplifier's output to the radiating antenna structure. The selected power-combining antenna consists of a unique printed (metalized) microstrip circuit on a ceramic type dielectric substrate which is backed by a shallow lightweight aluminum cavity which sums the power of four microwave sources. The antenna behaves like two one-half wavelength slot-line antennas coupled together via their common cavity structure.

Fitzsimmons, G. W.↗

NASA NTRS1981

Advanced Microwave Moisture Sounder (AMMS) for WB-57F CCOPE mission

The AMMS, flown on the WB-57F Cooperative Convective Precipitation Experiment (CCOPE), collected data at three bands on either side of the 183.3 GHz water vapor line at + or - 2.25, + or - 5.00, and + or - 8.75 GHz. Data were also collected simultaneously at a single low-loss atmospheric window channel near 94 GHz. The AMMS scanner imaged the scene below the WB-57F over an angular range of + or - 45 degree about nadir with beam-widths of 2 degree and 1 degree for the 94 GHz and 183 GHz sensors, respectively. The radiometer system operated under control of the onboard microcomputer used to: store radiometric data on the AMMS flight recorder, operate the stepper motor driven scanner, and collect pertinent housekeeping data for the system. A portable ground support system was used following each CCOPE flight to provide quick-look data analysis. The CCOPE flight logs and tape of the AMMS data were delivered to NASA.

Gagliano, J. A.↗

NASA NTRS1981

Metallization for large-area solar cells

In large area, low cost solar cells of any type, the contact and grid structure metallization is an important factor which has an effect on the efficiency of the solar cell and its reliability. The present investigation is concerned with aspects of solar cell efficiency. An optimized metallization design leads to minimum total power loss, which is related to a simultaneous minimization of ohmic voltage drops and of shading of the front surface of the cell by the overlaid metal. The requirements regarding the design for a low-loss metallization pattern for the front surface of large area solar cells are represented by a set of design rules listed in a table. The total shading and voltage drop on such cells can be held to about 5%. However, not every metallization process is suited for meeting the requirements of the low-cost design. The low losses can be achieved only by use of several bus lines containing a bulk conductor, such as a wire.

Wolf, M.↗

NASA NTRS1985

Pure Glasses From Multicomponent Gels

Report describes experiments with multicomponent gels for preparation of pure glass. Experiments aimed at developing zerogravitation process for fabrication of low-loss optical fibers.

Mukherjee, S. P.↗

NASA NTRS1984

Two-beam interferometer for optical constants measurements at near-millimeter wavelengths

A simple and versatile instrument for the measurement of optical constants in the near millimeter spectral region is described. Studies of quasi-optical components used in this instrument for effective beam transmission and control are reported. These studies include transmission characteristics of dielectric waveguides and performance of a variable coupler based on frustrated total internal reflection. Operation of this instrument as a two-beam interferometer for determining the index of refraction or as a device to measure transmission for determining the absorption coefficient are described. Values measured with this instrument at 245 GHz, using an optically pumped molecular laser as the source, are reported for several low-loss materials. Appropriate corrections and error estimates are discussed. The potential for improvement and increased accuracies are discussed.

Jones, C. R.↗

NASA NTRS1984

Spaceborne radar subsurface imaging in hyperarid regions

Imaging data acquired with the Shuttle Imaging Radar (SIR-A) over the hyperarid region of Egypt/Sudan clearly show surface penetration through the sand cover. Even though absorption does occur in the sand layer, surface refraction leads to a steeper incidence angle at the sand/bedrock interface resulting in a stronger backscatter. A simple backscatter model shows that for a low-loss thin sand layer the presence of the covering layer enhances the capability to image the subsurface interface, particularly at large incidence angles and HH polarization.

Elachi, C.↗

NASA NTRS1984

NASA OAST perspective

An advanced OTV is one of a number of advanced STS vehicles that the NASA OAST Space Systems Division Transportation Systems Office identified as candidates for future vehicle development. Vehicle requirements as well as technology needs and need dates were established and technology programs initiated to support those potential developments in a timely manner. It is assumed that advanced OTV will be space based and fully reusable for low cost operations, use aeroassist for return to low-Earth-orbit, and evolve to a man-rated system. The propulsion system will need to maintain high performance over a wide thrust range for mission flexibility, ranging from the transfer of large, acceleration limited structures from LEO to GEO, to demanding high reliability round-trip manned missions. Technology advances are needed in propulsion, aerobraking, low-gravity cryogenic fluid management, and in environmentally compatible, low-loss cryogenic tankage. In addition, diagnostic instrumentation for monitoring the health of on-board components and systems, and automated check-out capability will enhance low-cost space based OTV operations.

Stephenson, F.↗

NASA NTRS1985

Monolithic optical integrated control circuitry for GaAs MMIC-based phased arrays

Gallium arsenide (GaAs) monolithic microwave integrated circuits (MMIC's) show promise in phased-array antenna applications for future space communications systems. Their efficient usage will depend on the control of amplitude and phase signals for each MMIC element in the phased array and in the low-loss radiofrequency feed. For a phased array contining several MMIC elements a complex system is required to control and feed each element. The characteristics of GaAs MMIC's for 20/30-GHz phased-array systems are discussed. The optical/MMIC interface and the desired characteristics of optical integrated circuits (OIC's) for such an interface are described. Anticipated fabrication considerations for eventual full monolithic integration of optical integrated circuits with MMIC's on a GaAs substrate are presented.

Bhasin, K. B.↗

NASA NTRS1941

Experimental investigations on freely exposed ducted radiators

This report deals with the relation between the open areas, the drag, and the air flow as observed on freely exposed, ducted radiators - the air conductivity being modified from zero to one unit. In conjunction with theoretical results, the individual components of the drag of ducted radiators are discussed and general rules established for low-loss ducts. The influence of the wall thickness of the ducts, of the length ratio of the exit, and the effects of sonic velocity on diffusers are dealt with by special measurement.

Linke, W↗

NASA NTRS1983

Periodic reverse current pulsing to form uniformly sized feed through conductors

A large number of electrically conductive solid, dense feed-through paths for the high-speed low-loss transfer of electrical signals between integrated circuits of a single silicon-on-sapphire body, or between integrated circuits of several silicon-on-sapphire bodies, are provided by an electroforming method utilizing periodic reverse-current pulsing.

Anthony, Thomas R.↗

NASA NTRS1983

Alignment-enhancing feed-through conductors for stackable silicon-on-sapphire wafers

Alignment-enhancing electrically conductive feed-through paths are provided for the high-speed low-loss transfer of electrical signals between integrated circuits of a plurality of silicon-on-sapphire bodies arrayed in a stack. The alignment-enhancing feed-throughs are made by a process involving the drilling of holes through the body, double-sided sputtering, electroplating, and the filling of the holes with solder by capillary action. The alignment-enhancing feed-throughs are activated by forming a stack of wafers and remelting the solder whereupon the wafers, and the feed-through paths, are pulled into alignment by surface tension forces.

Anthony, Thomas R.↗