Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “linear switching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

On some numerical schemes for transonic flow problems

New second-order-accurate finite-difference approximations for a class of nonlinear PDEs of mixed type, which includes the two-dimensional low-frequency transonic small-disturbance equation (TSD) and full-potential equation (FP), are presented. For the TSD equation, the scheme is implemented via a time-splitting algorithm; the inclusion of flux limiters keeps the total variation nonincreasing and eliminates spurious oscillations near shocks. Global-linear-stability, TVD, and entropy-stability results are proved. Numerical results for the flow over a thin airfoil are presented. Current techniques used to solve the TSD equation may easily be extended to second-order accuracy by this method. For the FP equation, the new scheme requires no subsonic/supersonic switching and no numerical flux biasing. Global linear stability for all values of the Mach number is proved.

Mostrel, Marco Mosche↗
NASA NTRS2012

Analog bus driver and multiplexer

For a source-follower signal chain, the ohmic drop in the selection switch causes unacceptable voltage offset, non-linearity, and reduced small signal gain. For an op amp signal chain, the required bias current and the output noise rises rapidly with increasing the array format due to a rapid increase in the effective capacitance caused by the Miller effect boosting up the contribution of the bus capacitance. A new switched source-follower signal chain circuit overcomes limitations of existing op-amp based or source follower based circuits used in column multiplexers and data readout. This will improve performance of CMOS imagers, and focal plane read-out integrated circuits for detectors of infrared or ultraviolet light.

Pain, Bedabrata↗
NASA NTRS1983

Effects of ISI and satellite channel nonlinearity on Viterbi demodulation/decoding

It is shown that, for convolutionally coded transmission over bandwidth-constrained channels, a mere reversal of the switching direction at the encoder output produces a change in the system bit error probability performance. This change is significant when the Viterbi demodulator/decoder is matched to the total channel memory and is more significant for linear channels than for nonlinear ones. The reversal of switching direction is a simple demonstration of the fact that the well-known optimum codes for the linear AGWN channel are no longer necessarily optimum for a bandwidth-constrained channel with or without the addition of channel nonlinearity. It is concluded that potentially significant performance improvement can be obtained by matching the encoder (through the appropriate choice of tap weights and modulo-2 summers) to the channel in addition to matching the demodulator/decoder to the channel for a given encoder.

Divsalar, D.↗
NASA NTRS2006

Switching Characteristics of a 4H-SiC Based Bipolar Junction Transistor to 200 C

Static curves and resistive load switching characteristics of a 600 V, 4 A rated, SiC-based NPN bipolar power transistor (BJT) were observed at selected temperatures from room to 200 C. All testing was done in a pulse mode at low duty cycle (approx.0.1 percent). Turn-on was driven by an adjustable base current pulse and turn-off was accelerated by a negative base voltage pulse of 7 V. These base drive signals were implemented by 850 V, gated power pulsers, having rise-times of roughly 10 ns, or less. Base charge sweep-out with a 7 V negative pulse did not produce the large reverse base current pulse seen in a comparably rated Si-based BJT. This may be due to a very low charge storage time. The decay of the collector current was more linear than its exponential-like rise. Switching observations were done at base drive currents (I(sub B)) up to 400 mA and collector currents (I(sub C)) up to 4 A, using a 100 Omega non-inductive load. At I(sub B) = 400 mA and I(sub C) = 4 A, turn-on times typically varied from 80 to 94 ns, over temperatures from 23 to 200 C. As expected, lowering the base drive greatly extended the turn-on time. Similarly, decreasing the load current to I(sub C) = 1 A with I(sub B) = 400 mA produced turn-on times as short as 34 ns. Over the 23 to 200 C range, with I(sub B) = 400 mA and I(sub C) = 4 A, turn-off times were in the range of 72 to 84 ns with the 7 V sweep-out.

Niedra, Janis M.↗
NASA NTRS1968

Dynamic linearity measurement technique

Measurement technique involves frequency modulated discriminator which produces an error signal as two signals, one of known and one of unknown frequency. The signals are electronically switched to a discriminator input, allowing independent measuring of dynamic linearity in a frequency modulated subcarrier oscillator.

Merz, K.↗
DOE OSTI2022

Metaplastic and energy-efficient biocompatible graphene artificial synaptic transistors for enhanced accuracy neuromorphic computing

CMOS-based computing systems that employ the von Neumann architecture are relatively limited when it comes to parallel data storage and processing. In contrast, the human brain is a living computational signal processing unit that operates with extreme parallelism and energy efficiency. Although numerous neuromorphic electronic devices have emerged in the last decade, most of them are rigid or contain materials that are toxic to biological systems. In this work, we report on biocompatible bilayer graphene-based artificial synaptic transistors (BLAST) capable of mimicking synaptic behavior. The BLAST devices leverage a dry ion-selective membrane, enabling long-term potentiation, with ~50 aJ/µm 2 switching energy efficiency, at least an order of magnitude lower than previous reports on two-dimensional material-based artificial synapses. The devices show unique metaplasticity, a useful feature for generalizable deep neural networks, and we demonstrate that metaplastic BLASTs outperform ideal linear synapses in classic image classification tasks. With switching energy well below the 1 fJ energy estimated per biological synapse, the proposed devices are powerful candidates for bio-interfaced online learning, bridging the gap between artificial and biological neural networks.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1999

Electrical Field Effects in Phthalocyanine Film Growth by Vapor Deposition

Phthalocyanine, an organic material, is a very good candidate for non-linear optical application, such as high-speed switching and optical storage devices. Phthalocyanine films have been synthesized by vapor deposition on quartz substrates. Some substrates were coated with a very thin gold film for introducing electrical field. These films have been characterized by surface morphology, material structure, chemical and thermal stability, non-linear optical parameters, and electrical behaviors. The films have excellent chemical and optical stability. However, the surface of these films grown without electrical field shows flower-like morphology. When films are deposited under an electrical field ( an aligned structure is revealed on the surface. A comparison of the optical and electrical properties and the growth mechanism for these films grown with and without an electrical field will be discussed.

Banks, Curtis E.↗
NASA NTRS1973

Analysis and modeling of a family of two-transistor parallel inverters

A family of five static dc-to-square-wave inverters, each employing a square-loop magnetic core in conjunction with two switching transistors, is analyzed using piecewise-linear models for the nonlinear characteristics of the transistors, diodes, and saturable-core devices. Four of the inverters are analyzed in detail for the first time. These analyses show that, by proper choice of a frame of reference, each of the five quite differently appearing inverter circuits can be described by a common equivalent circuit. This equivalent circuit consists of a five-segment nonlinear resistor, a nonlinear saturable reactor, and a linear capacitor. Thus, by proper interpretation and identification of the parameters in the different circuits, the results of a detailed solution for one of the inverter circuits provide similar information and insight into the local and global behavior of each inverter in the family.

Lee, F. C. Y.↗
NASA NTRS1981

Optimal trajectories in atmospheric flight

Aspects of optimization theory and switching theory are discussed, taking into account the necessary conditions for extrema, a solution subject to constraints, the calculus of variations, the Pontryagin maximum principle, the canonical transformation, Contensou's domain of maneuverability, optimal switching, a junction with singular arc, and linearized singular control. Equations of motion are considered along with aerodynamic and propulsive forces, the general properties of optimal trajectories, flight in a horizontal plane, optimal coasting flight, supersonic cruise, the supersonic turn, supersonic maneuvers in a vertical plane, energy state approximation, a modified Chapman's formulation for optimal reentry trajectories, optimal planar reentry trajectories, and an optimal glide of reentry vehicles. Orbital aerodynamic maneuvers are examined, giving attention to aerodynamic capture, a change in the apogee, a change in the eccentricity, a change in the perigee, an orbital maneuver, an aerodynamic maneuver, and a combined maneuver.

Vinh, N. X.↗
NASA NTRS1997

Application of Laser Based Ultrasound for NDE of Damage in Thick Stitched Composites

As design engineers implement new composite systems such as thick, load bearing composite structures, they must have certifiable confidence in structure s durability and worthiness. This confidence builds from understanding the structural response and failure characteristics of simple components loaded in testing machines to tests on full scale sections. Nondestructive evaluation is an important element which can provide quantitative information on the damage initiation, propagation, and final failure modes for the composite structural components. Although ultrasound is generally accepted as a test method, the use of conventional ultrasound for in-situ monitoring of damage during tests of large structures is not practical. The use of lasers to both generate and detect ultrasound extends the application of ultrasound to in- situ sensing of damage in a deformed structure remotely and in a non-contact manner. The goal of the present research is to utilize this technology to monitor damage progression during testing. The present paper describes the application of laser based ultrasound to quantify damage in thick stitched composite structural elements to demonstrate the method. This method involves using a Q-switched laser to generate a rapid, local linear thermal strain on the surface of the structure. This local strain causes the generation of ultrasonic waves into the material. A second laser used with a Fabry-Perot interferometer detects the surface deflections. The use of fiber optics provides for eye safety and a convenient method of delivering the laser over long distances to the specimens. The material for these structural elements is composed of several stacks of composite material assembled together by stitching through the laminate thickness that ranging from 0.5 to 0.8 inches. The specimens used for these nondestructive evaluation studies had either impact damage or skin/stiffener interlaminar failure. Although little or no visible surface damage existed, internal damage was detected by laser based ultrasound.

Anastasi, Robert F.↗
NASA NTRS2004

Digital Beam Steering Device Based on Decoupled Birefringent Prism Deflector and Polarization Rotator

We describe digital beam deflectors (DBDs) based on liquid crystals. Each stage of the device comprises a polarization rotator and a birefringent prism deflector. The birefringent prism deflects the beam by an angle that depends on polarization of the incident beam. The prism can be made of the uniaxial smectic A (SmA) liquid crystal (LC) or a solid crystal such as yttrium orthovanadate (YVO4). SmA prisms have high birefringence and can be constructed in a variety of shapes, including single prisms and prismatic blazed gratings of different angles and profiles. We address the challenges of uniform alignment of SmA, such as elimination of focal conic domains. Rotation of linear polarization is achieved by an electrically switched twisted nematic (TN) cell. A DBD composed of N rotator-deflector pairs steers the beam into 2(sup N) directions. As an example, we describe a four-stage DBD deflecting normally incident laser beam within the range of +/- 56 mrad with 8 mrad steps. Redirection of the beam is achieved by switching the TN cells.

Pishnyak, Oleg↗
NASA NTRS2005

Support of NASA ADR/ Cross-Enterprise NRA Advanced Adiabatic Demagnetization Refrigerators for Continuous Cooling from 10K to 50mK, Development of a Heat Switch

Mechanical heat switches are used in conjunction with sorption refrigerators, adiabatic demagnetization refrigerators and for other cryogenic tasks including the pre-cooling cryogenic systems. They use a mechanical actuator which closes Au plated Cu jaws on an Au plated Cu bar. The thermal conductance in the closed position is essentially independent of the area of the jaws and proportional to the force applied. It varies linearly with T. It is approximately 10mW/K for 200 N at 1.5K. In some applications, the heat switch can be driven from outside the cryostat by a rotating rod and a screw. Such heat switches are available commercially from several sources. In other applications, including systems for space, it is desirable to drive the switch using a cold linear motor, or solenoid. Superconducting windings are used at temperatures s 4.2K to minimize power dissipation, but are not appropriate for pre-cooling a system at higher temperatures. This project was intended to improve the design of solenoid activated mechanical heat switches and to provide such switches as required to support the development of Advanced Adiabatic Demagnetization Refrigerators for Continuous Cooling from 10 K to 50 mK at GSFC. By the time funding began in 5/1/01, the immediate need for mechanical heat switches at GSFC had subsided but, at the same time, the opportunity had arisen to improve the design of mechanical heat switching by incorporating a "latching solenoid". In this device, the solenoid current is required only for changing the state of the switch and not during the whole time that the switch is closed.

Richards, Paul L.↗
NASA NTRS1979

Antenna feed system for receiving circular polarization and transmitting linear polarization

An invention is described which provides for receiving a circularly polarized signal from an antenna feed connected to orthogonally spaced antenna elements. It also provides for transmitting a linearly polarized signal through the same feed without switches, and without suffering a 3 dB polarization mismatch loss, using an arrangement of hybrid junctions. The arrangement is comprised of two dividing hybrid junctions, each connected to a different pair of antenna elements and a summing hybrid junction. In one version, a receiver is connected to the summing hybrid junction directly. A diplexer is used to connect a transmitter to only one pair of antenna elements. In another version, designated left and right circularly polarized (LCP and RCP) transmitters are connected to the summing hybrid junction by separate diplexers, and separate LCP and RCP sensitive receivers are connected to the diplexers in order to transmit linearly polarized signals using all four antenna elements while receiving circularly polarized signals as before. An orthomode junction and horn antenna may replace the two dividing hybrid junctions and antenna feed.

Seidel, B. L.↗
DOE OSTI2021

Switching Device-Cognizant Sequential Distribution System Restoration

This paper presents an optimization framework for sequential reconfiguration using an assortment of switching devices and repair process in distribution system restoration. Compared to existing studies, this paper considers types, capabilities and operational limits of different switching devices, making it applicable in practice. We develop a novel multi-phase method to find the optimal sequential operation of various switching devices and repair faulted areas. We consider circuit breakers, reclosers, sectionalizers, load breaker switches, and fuses. The switching operation problem is decomposed into two mixed-integer linear programming (MILP) subproblems. The first subproblem determines the optimal network topology and estimates the number of steps to reach that topology, while the second subproblem generates a sequence of switching operations to coordinate the switches. For repairing the faults, we design an MILP model that dispatches repair crews to clear faults and replace melted fuses. After clearing a fault, we update the topology of the network by generating a new sequence of switching operations, and the process continues until all faults are cleared. To improve the computational efficiency, a network reduction algorithm is developed to group line sections, such that only switchable sections are present in the reduced network. The proposed method is validated on the IEEE 123-bus and 8500-bus systems.

distribution system↗
NASA NTRS1981

Antenna feed system for receiving circular polarization and transmitting linear polarization

An object is to provide for receiving a circularly polarized signal from an antenna feed (10) connected to orthogonally spaced antenna elements (11, 12, 13, 14) and for transmitting a linearly polarized signal through the same feed without switches, and without suffering a 3 dB polarization mismatch loss, using an arrangement of hybrid junctions. The arrangement is comprised of two dividing hybrid junctions (15, 16), each connected to a different pair of antenna elements and a summing hybrid junction (17). In one embodiment, a receiver (18) is connected to the summing hybrid junction directly. A diplexer (19a or 19b) is used to connect a transmitter (20a or 20b) to only one pair of antenna elements. In an alternative embodiment, designated left and right circularly polarized (LCP and RCP) transmitters (21, 22) are connected to the summing hybrid junction by separate diplexers (23, 24), and separate LCP and RCP sensitive receivers (25, 26) are connected to the diplexers in order to transmit linearly polarized signals using all four antenna elements while receiving circularly polarized signals as before. An orthomode junction (30) and horn antenna (32) may replace the two dividing hybrid junctions (15, 16) and antenna feed (10).

Seidel, Boris L.↗
NASA NTRS1980

Application of small-signal modeling and measurement techniques to the stability analysis of an integrated switching-mode power system

Small-signal modeling techniques are used in a system stability analysis of a breadboard version of a complete functional electrical power system. The system consists of a regulated switching dc-to-dc converter, a solar-cell-array simulator, a solar-array EMI filter, battery chargers and linear shunt regulators. Loss mechanisms in the converter power stage, including switching-time effects in the semiconductor elements, are incorporated into the modeling procedure to provide an accurate representation of the system without requiring frequency-domain measurements to determine the damping factor. The small-signal system model is validated by the use of special measurement techniques which are adapted to the poor signal-to-noise ratio encountered in switching-mode systems. The complete electrical power system with the solar-array EMI filter is shown to be stable over the intended range of operation.

Wong, R. C.↗
DOE OSTI2021

Megavolt bremsstrahlung measurements from linear induction accelerators demonstrate possible use as a FLASH radiotherapy source to reduce acute toxicity

Abstract Recent studies indicate better efficacy and healthy tissue sparing with high dose-rate FLASH radiotherapy (FLASH-RT) cancer treatment. This technique delivers a prompt high radiation dose rather than fractional doses over time. While some suggest thresholds of > 40 Gy s −1 with a maximal effect at > 100 Gy s −1 , accumulated evidence shows that instantaneous dose-rate and irradiation time are critical. Mechanisms are still debated, but toxicity is minimized while inducing apoptosis in malignant tissue. Delivery technologies to date show that a capability gap exists with clinic scale, broad area, deep penetrating, high dose rate systems. Based on these trends, if FLASH-RT is adopted, it may become a dominant approach except in the least technologically advanced countries. The linear induction accelerator (LIA) developed for high instantaneous and high average dose-rate, species independent charged particle acceleration, has yet to be considered for this application. We review the status of LIA technology, explore the physics of bremsstrahlung-converter-target interactions and our work on stabilizing the electron beam. While the gradient of the LIA is low, we present our preliminary work to improve the gradient by an order of magnitude, presenting a point design for a multibeam FLASH-RT system using a single accelerator for application to conformal FLASH-RT.

42 ENGINEERING↗
DOE OSTI2021

Tuning the charge density wave quantum critical point and the appearance of superconductivity in Ti Se 2

The transition metal dichalcogenide TiSe 2 is an ideal correlated system for studying the interplay between superconductivity (SC) and a charge density wave (CDW) because both symmetry-breaking phases can be easily controlled by either Cu intercalation or physical pressure. SC appears in proximity to a CDW quantum critical point (QCP) induced by both Cu intercalation and applied pressure, raising the possibility of CDW-driven SC. Here, we report tuning the CDW QCP by simultaneously controlling Cu intercalation and external pressure and the appearance of a SC dome centered on the tunable QCP. When subjected to pressure, CDW ordering of Cu-intercalated Cu 0.025 TiSe 2 is completely suppressed at 2.3 GPa, where the residual resistivity and the resistivity-temperature exponent decrease sharply, indicating the presence of the CDW QCP. The upper critical field of Cu 0.025 TiSe 2 is 3.51 kOe, 16 times larger than that of pristine TiSe 2 , and its temperature dependence is linear, indicating that SC of TiSe 2 is switched from the two-dimensional- to anisotropic three-dimensional-like by Cu intercalation. These discoveries show that the simultaneous application of Cu intercalation and pressure move the CDW QCP and that the highest SC transition temperature is pinned to the QCP, suggesting that the SC in TiSe 2 is strongly correlated with CDW quantum criticality.

2-dimensional systems↗