Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

A digital signal processing system for coherent laser radar

A data processing system for use with continuous-wave lidar is described in terms of its configuration and performance during the second survey mission of NASA'a Global Backscatter Experiment. The system is designed to estimate a complete lidar spectrum in real time, record the data from two lidars, and monitor variables related to the lidar operating environment. The PC-based system includes a transient capture board, a digital-signal processing (DSP) board, and a low-speed data-acquisition board. Both unprocessed and processed lidar spectrum data are monitored in real time, and the results are compared to those of a previous non-DSP-based system. Because the DSP-based system is digital it is slower than the surface-acoustic-wave signal processor and collects 2500 spectra/s. However, the DSP-based system provides complete data sets at two wavelengths from the continuous-wave lidars.

Hampton, Diana M.↗
NASA NTRS1991

Spectroscopic characterization of dynamical processes for Tm,Ho:YAG lasers

The energy transfer processes in Tm,Ho:YAG lasers were investigated in spectral studies and measurements of the temporal response to pulsed excitation. These processes include the population of the 3H4 pump band of Tm, cross-relaxation in Tm, the transfer of energy from Tm to Ho, and various loss mechanisms. It was found that the Tm cross-relaxation is due to a dipole-dipole interaction between Tm ions and that the rate of this process is a function of temperature and ion concentration.

Armagan, G.↗
NASA NTRS1983

Lightweight solar array blanket tooling, laser welding and cover process technology

A two phase technology investigation was performed to demonstrate effective methods for integrating 50 micrometer thin solar cells into ultralightweight module designs. During the first phase, innovative tooling was developed which allows lightweight blankets to be fabricated in a manufacturing environment with acceptable yields. During the second phase, the tooling was improved and the feasibility of laser processing of lightweight arrays was confirmed. The development of the cell/interconnect registration tool and interconnect bonding by laser welding is described.

Dillard, P. A.↗
NASA NTRS1993

Lunar laser ranging data processing in a Unix/X windows environment

In cooperation with the NASA Crustal Dynamics Project initiative placing workstation computers at each of its laser ranging stations to handle data filtering and normalpointing, MLRS personnel have developed a new generation of software to provide the same services for the lunar laser ranging data type. The Unix operating system and X windows/Motif provides an environment for both batch and interactive filtering and normalpointing as well as prediction calculations. The goal is to provide a transportable and maintainable data reduction environment. This software and some sample displays are presented. that the lunar (or satellite) datacould be processed on one computer while data was taken on the other. The reduction of the data was totally interactive and in no way automated. In addition, lunar predictions were produced on-site, another first in the effort to down-size historically mainframe-based applications. Extraction of earth rotation parameters was at one time attempted on site in near-realtime. In 1988, the Crustal Dynamics Project SLR Computer Panel mandated the installation of Hewlett-Packard 9000/360 Unix workstations at each NASA-operated laser ranging station to relieve the aging controller computers of much of their data and communications handling responsibility and to provide on-site data filtering and normal pointing for a growing list of artificial satellite targets. This was seen by MLRS staff as an opportunity to provide a better lunar data processing environment as well.

Ricklefs, Randall L.↗
NASA NTRS1987

The recording and processing of pulsed laser diode spectra

A system capable of measuring and statistically analyzing wavelength and intensity fluctuations in pulsed laser diode output beams has been developed. The snapshot wavelength-intensity performance of laser diodes emitting discrete short-duration optical pulse is determined by isolating and recording individual pulses. Statistical processing of the resultant data generates information about the magnitude and/or frequency of occurrence of power variations or wavelength fluctuations in narrow optical bands. The system configuration along with plots depicting results based on measurements taken for various laser diodes are presented.

Fuhr, Peter L.↗
NASA NTRS1987

Excimer laser annealing: A gold process for CZ silicon junction formation

A cold process using an excimer laser for junction formation in silicon has been evaluated as a way to avoid problems associated with thermal diffusion. Conventional thermal diffusion can cause bulk precipitation of SiOx and SiC or fail to completely activate the dopant, leaving a degenerate layer at the surface. Experiments were conducted to determine the feasibility of fabricating high quality p-n junctions using a pulsed excimer laser for junction formation at remelt temperature with ion-implanted surfaces. Solar-cell efficiency exceeding 16 percent was obtained using Czochralski single-crystal silicon without benefit of back surface field or surface passivation. Characterization shows that the formation of uniform, shallow junctions (approximately 0.25 micron) by excimer laser scanning preserves the minority carrier lifetime that leads to high current collection. However, the process is sensitive to initial surface conditions and handling parameters that drive the cost up.

Wong, David C.↗
NASA NTRS1990

New Space Domain Processing Technique for Pulsed Laser Velocimetry

A new and fast data processing technique for pulsed-laser-velocimetry data is described. A simplified cross correlation algorithm was developed which uses the time history information of the recorded particle images. It is shown that, the use of the particle time history information (which can be obtained using an electronic camera to record the particle exposures) facilitates high speed processing and unambiguous velocity vector information. It was found that a complex convection vortex flow can be recorded and completely processed in less than 2 min on a personal computer, producing a two-dimensional map of the flow field containing over 300 velocity vectors.

Wernet, Mark P.↗
NASA NTRS2021

Data Processing of Miniaturized Laser Heterodyne Radiometer (mini-LHR) Ground Instrument Retrievals

The Miniaturized Laser Heterodyne Radiometer (mini-LHR) is a passive ground instrument that observes the mole fraction of carbon dioxide (CO) and methane (CH)in the atmospheric column by measuring their absorption of sunlight at 1.6 microns. A laser heterodyne radiometer is similar in design to the super heterodyne radio receiver that is well known by ham radio enthusiasts. While not previously a commercial technique, laser heterodyne radiometers have a history of measuring atmospheric trace gases that started in the 1960s. With the commercial availability of inexpensive, low-power, thumbnail-sized lasers developed for the telecommunications industry, it was possible to miniaturize this technique and ultimately commercialize it. The mini-LHR has been under development at NASA GSFC since 2009. During that time, in addition to signicant technical improvements, processing has also evolved and been streamlined. Here we present details of the processing approach for raw mini-LHR data to produce 30- and 60-minute data products of CH and CO column mole fractions. Processing occurs in two general stages: a python-based pre-processing of raw data, followed by ingestion into a Planetary Spectrum Generator (PSG) retrieval algorithm. Raw data processing involves removal of outliers, correcting for changes in air mass throughout the day, averaging scans, and ultimately converting averaged scans into transmittance vs. wavelength. The PSG retrieval simulates a spectra for the time/day/location of the scan with meteorological inputs from Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2) data set and then perturbs the concentrations of CO and CH to obtain a t based on an iterative least-squares curve fitting procedure.

Giancarlo Roberto Zambrano↗
NASA NTRS1973

Processing of the laser Doppler velocimeter signals

The laser Doppler velocimeter (LDV) is a probeless technique that provides a remote measurement of mean and fluctuating velocities. The measurement is actually obtained from small particles embedded in the flow which scatter light from an illuminating laser beam interference pattern. A portion of this scattered light is collected by a photomultiplier which yields an electronic signal whose frequency is directly proportional to the velocity of the small particles. The purpose of this paper is to describe and critically compare three techniques most used to process this electronic signal. These techniques are: (1) spectrum analyzer - a frequency scanning filter (frequency domain instrument), (2) wide-band frequency tracker - a frequency lock loop (frequency domain instrument), and (3) high-speed frequency counter - an interval timer (time domain instrument). The study determines the ability of each technique to process the LDV signal and yield velocity data to be used in determining the flow characteristics.

Meyers, J. F.↗
NASA NTRS1986

Laser-assisted solar cell metallization processing

The status of the laser-assisted solar cell metallization processing is described. Metallo-organic silver films were spun-on by argon ion laser beam pyrolysis. The metallo-organic decomposition (MOD) film was spun-on an evaporated Ti/Pd film to produce tood adhesion. In a maskless process, the argon ion laser writes the contact pattern. The film is then built up to obtain the required conductivity using conventional silverplating process. The Ti/Pd film in the field is chemically etched using the plated silver film as the mask. The width of the contact pattern is determined by the power of the laser. Widths as thin as 20 microns were obtained using 0.66 W of laser power. Cells fabricated with the 50 micron line widths of 4 ohm-cm floating zone (Fz) silicon-produced efficiencies of 16.6% (no passivation) which were equivalent to the best cells using conventional metallization/lithography and no passivation.

Meier, D. L.↗
NASA NTRS1977

Correlation between stimulated scattering processes and laser-induced damage in crystalline quartz

The results of a systematic series of experiments to uncover possible correlation between laser-induced stimulated-Brillouin-scattering (SBS) phonons and damage in quartz are presented. Such correlation is confirmed and the various thresholds are established. The anomalous transmission factor under phonon generation is found to decay exponentially as predicted with increasing incident laser power. The LF SBS phonon is also demonstrated to be a sensitive probe for precatastrophic damage.

Yu, C.↗
NASA NTRS1983

Measurement of heat pump processes induced by laser radiation

A series of experiments was performed in which a suitably tuned CO2 laser, frequency doubled by a Tl3AsSe37 crystal, was brought into resonance with a P-line or two R-lines in the fundamental vibration spectrum of CO. Cooling or heating produced by absorption in CO was measured in a gas-thermometer arrangement. P-line cooling and R-line heating could be demonstrated, measured, and compared. The experiments were continued with CO mixed with N2 added in partial pressures from 9 to 200 Torr. It was found that an efficient collisional resonance energy transfer from CO to N2 existed which increased the cooling effects by one to two orders of magnitude over those in pure CO. Temperature reductions in the order of tens of degrees Kelvin were obtained by a single pulse in the core of the irradiated volume. These measurements followed predicted values rather closely, and it is expected that increase of pulse energies and durations will enhance the heat pump effects. The experiments confirm the feasibility of quasi-isentropic engines which convert laser power into work without the need for heat rejection. Of more immediate potential interest is the possibility of remotely powered heat pumps for cryogenic use, such applications are discussed to the extent possible at the present stage.

Garbuny, M.↗
NASA NTRS1994

Development of infrared sensors using energy transfer/energy upconversion processes: Study of laser excited fluorescence in rare Earth ion doped crystals

A summary is presented of the spectroscopic study of three systems: LaF3:Ho(3+), LaF3:Er(3+) and CaF2:Nd(3+). When the D levels of Ho(3+) in LaF3 were resonantly excited with a laser beam of 640 nm, upconverted emissions were detected from J (416 nm), F (485 nm), and E (546 nm) levels. Energy upconverted emissions were also observed from F and E levels of Ho(3+) when the material was excited with an 800 nm near infrared laser. When the D levels of Er(3+) in LaF3 were resonantly excited with a laser beam of 637 nm, upconverted emissions were detected from the E (540 nm) and P (320, 400, and 468 nm) levels. Energy upconverted emissions were also observed from F, E, and D levels of Er(3+) when the material was resonantly excited with an 804 nm near infrared laser. When the D levels of Nd(3+) in CaF2 were resonantly excited with a laser beam of 577 nm, upconverted emissions were detected from the L (360 and 382 nm), K (418 nm), and I (432 nm) levels. Very weak upconverted emissions were detected when this system was irradiated with a near infrared laser. The numbers in parentheses are the wavelengths of the emissions.

Nash-Stevenson, S. K.↗
NASA NTRS2002

Application of Reconfigurable Computing Technology to Multi-KiloHertz Micro-Laser Altimeter (MMLA) Data Processing

The Multi-KiloHertz Micro-Laser Altimeter (MMLA) is an aircraft based instrument developed by NASA Goddard Space Flight Center with several potential spaceflight applications. This presentation describes how reconfigurable computing technology was employed to perform MMLA signal extraction in real-time under realistic operating constraints. The MMLA is a "single-photon-counting" airborne laser altimeter that is used to measure land surface features such as topography and vegetation canopy height. This instrument has to date flown a number of times aboard the NASA P3 aircraft acquiring data at a number of sites in the Mid-Atlantic region. This instrument pulses a relatively low-powered laser at a very high rate (10 kHz) and then measures the time-of-flight of discrete returns from the target surface. The instrument then bins these measurements into a two-dimensional array (vertical height vs. horizontal ground track) and selects the most likely signal path through the array. Return data that does not correspond to the selected signal path are classified as noise returns and are then discarded. The MMLA signal extraction algorithm is very compute intensive in that a score must be computed for every possible path through the two dimensional array in order to select the most likely signal path. Given a typical array size with 50 x 6, up to 33 arrays must be processed per second. And for each of these arrays, roughly 12,000 individual paths must be scored. Furthermore, the number of paths increases exponentially with the horizontal size of the array, and linearly with the vertical size. Yet, increasing the horizontal and vertical sizes of the array offer science advantages such as improved range, resolution, and noise rejection. Due to the volume of return data and the compute intensive signal extraction algorithm, the existing PC-based MMLA data system has been unable to perform signal extraction in real-time unless the array is limited in size to one column, This limits the ability of the MMLA to operate in environments with sparse signal returns and a high number of noise return. However, under an IR&D project, an FPGA-based, reconfigurable computing data system has been developed that has been demonstrated to perform real-time signal extraction under realistic operating constraints. This reconfigurable data system is based on the commercially available Firebird Board from Annapolis Microsystems. This PCI board consists of a Xilinx Virtex 2000E FPGA along with 36 MB of SRAM arranged in five separately addressable banks. This board is housed in a rackmount PC with dual 850MHz Pentium processors running the Windows 2000 operating system. This data system performs all signal extraction in hardware on the Firebird, but also runs the existing "software based" signal extraction in tandem for comparison purposes. Using a relatively small amount of the Virtex XCV2000E resources, the reconfigurable data system has demonstrated to improve performance improvement over the existing software based data system by an order of magnitude. Performance could be further improved by employing parallelism. Ground testing and a preliminary engineering test flight aboard the NASA P3 has been performed, during which the reconfigurable data system has been demonstrated to match the results of the existing data system.

Powell, Wesley↗
NASA NTRS1990

CO2 lasers and applications II; Proceedings of the Third European Congress on Optics, The Hague, Netherlands, Mar. 12-14, 1990

Recent advances in CO2 laser technology and its applications are examined. Topics discussed include the excitation of CO2 lasers by microwave discharge, a compact RF-excited 12-kW CO2 laser, a robotic laser for three-dimensional cutting and welding, three-dimensional CO2-laser material processing with gantry machine systems, and a comparison of hollow metallic waveguides and optical fibers for transmitting CO2-laser radiation. Consideration is given to an aerodynamic window with a pump cavity and a supersonic jet, cutting and welding Al using a high-repetition-rate pulsed CO2 laser, speckle reduction in CO2 heterodyne laser radar systems, high-power-laser float-zone crystal growth, melt dynamics in surface processing with laser radiation, laser hardfacing, surface melting of AlSi10Mg with CO2 laser radiation, material processing with Cu-vapor lasers, light-induced flow at a metal surface, and absorption measurements in high-power CW CO2-laser processing of materials.

Opower, Hans↗
NASA NTRS2008

Patterning of Indium Tin Oxide Films

A relatively rapid, economical process has been devised for patterning a thin film of indium tin oxide (ITO) that has been deposited on a polyester film. ITO is a transparent, electrically conductive substance made from a mixture of indium oxide and tin oxide that is commonly used in touch panels, liquid-crystal and plasma display devices, gas sensors, and solar photovoltaic panels. In a typical application, the ITO film must be patterned to form electrodes, current collectors, and the like. Heretofore it has been common practice to pattern an ITO film by means of either a laser ablation process or a photolithography/etching process. The laser ablation process includes the use of expensive equipment to precisely position and focus a laser. The photolithography/etching process is time-consuming. The present process is a variant of the direct toner process an inexpensive but often highly effective process for patterning conductors for printed circuits. Relative to a conventional photolithography/ etching process, this process is simpler, takes less time, and is less expensive. This process involves equipment that costs less than $500 (at 2005 prices) and enables patterning of an ITO film in a process time of less than about a half hour.

Immer, Christopher↗
NASA NTRS2016

Challenges in Laser Sintering of Melt-Processable Thermoset Imide Resin

Polymer Laser Sintering (LS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. LS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. The objective of this project is to investigate the possibility of printing a melt-processable RTM370 imide resin powder terminated with reactive phenylethynyl groups by LS, followed by a postcure in order to promote additional crosslinking to achieve higher temperature (250-300 C) capability. A preliminary study to build tensile specimens by LS and the corresponding DSC and rheology study of RTM370 during LS process is presented.

Additive Manufacturing↗