SEARCH · Engineering Papers

Results for “large Eddy simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Numerical Study of Liquid Piston Compression Using Large-Eddy Simulation and Volume-of-Fluid Approach

Efforts to increase the efficiency of residential and commercial air conditioners and heat pumps have demonstrated that the compressor accounts for most of the system’s electrical energy usage. Therefore, the efficiency of this component should be improved to reduce its energy usage. The US Department of Energy’s Oak Ridge National Laboratory developed a near-isothermal liquid piston compressor (LPC) that uses propylene glycol (PG) to compress CO2. This report presents numerical studies of the LPC in which the compression chamber fills with injected PG from the bottom inlet. Numerical simulations were performed using the large-eddy simulation (LES) with the wall-adapting local eddy-viscosity (WALE) subgrid-scale model coupled with the multiphase volume-of-fluid (VOF) model to simulate the transient interface between gas and liquid and to capture the heat and mass transfer within the compression chamber. In this effort, effects of boundary conditions applied to the LES-VOF calculations (e.g., no wall, an adiabatic wall, and a wall with a heat flux subscribed) to the overall pressure and temperature of CO2 gas as well as the transient evolution of flow and heat transfer evolution within the compression chamber are investigated and discussed. It was found that the LES calculation with no wall have shown no dynamical flow patterns and the volume-averaged temperature of CO2 increased from 305 to 392.7 K, while LES calculations with a constant wall temperature or a wall heat flux had similar increases of CO2 temperatures. Results of LES simulation using a wall heat flux showed different stages in the compression process and revealed dynamical formation and interaction of CO2 gas layers and circulation flow patterns within the chamber that contribute to the overall heat transfer between the solid wall, gas, and liquid surface in the compressor.

Nguyen, Thien D.↗

DOE OSTI2020

Spatiotemporally dynamic implicit large eddy simulation using machine learning classifiers

In this article, we utilize machine learning to dynamically determine if a point on the computational grid requires implicit numerical dissipation for large eddy simulation (LES). The decision making process is learnt through a priori training on quantities derived from direct numerical simulation (DNS) data. In particular, we compute eddy-viscosities obtained through the coarse-graining of DNS quantities and utilize their projection onto a Gaussian distribution to categorize areas that may require dissipation. If our learning determines that closure is necessary, an upwinded scheme is utilized for computing the non-linear Jacobian. In contrast, if it is determined that closure is unnecessary, a symmetric and second-order accurate energy and enstrophy preserving Arakawa scheme is utilized instead. This results in a closure framework that precludes the specification of any model-form for the small scale contributions of turbulence but deploys an appropriate numerical dissipation from explicit closure driven hypotheses. Here, this methodology is deployed for the Kraichnan turbulence test-case and assessed through various statistical quantities such as angle-averaged kinetic energy spectra and vorticity structure functions. Our framework thus establishes a link between the use of explicit LES ideologies for closure and numerical dissipation-based modeling of turbulence leading to improved statistical fidelity of a posteriori simulations.

42 ENGINEERING↗

DOE OSTI2020

Improvement of Atmospheric Objective Analysis Over Sloping Terrain and Its Impact on Shallow-Cumulus Clouds in Large-Eddy Simulations

Surface topography strongly impacts the regional atmospheric circulation dynamically and thermodynamically. Over the Great Plains in the United States, the gently tilted slope is an important factor that impacts clouds, convection and regional circulations. This study enhances an atmospheric constrained variational analysis by using a terrain-following sigma vertical coordinate and applies to the data collected at the Southern Great Plain (SGP) site of the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) program. Sensitivity studies are performed to examine the impact of the terrain effects on the derived large-scale atmospheric forcing fields and the simulated shallow-cumulus clouds in large-eddy simulation (LES) driven by the forcing. We found that the terrain impacts on the large-scale forcing fields are mainly at lower levels and are strongly controlled by up/downslope winds. The response of the derived forcing to the slope of the terrain is monotonic, but the response of the simulated shallow-cumulus clouds is more complex and depends on several factors. Overall, the terrain impact is small over SGP due to the small slope angle. However, the flat-surface assumption may cause larger biases in the large-scale forcing fields at locations with steeper terrain. The new sigma-coordinate algorithm, with its consideration of surface slope, should be more suitable to derive large-scale objective analysis over regions with steep terrain for application to force single-column models, cloud resolving models and LES models.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Toward Exascale: Overview of Large Eddy Simulations and Direct Numerical Simulations of Nuclear Reactor Flows with the Spectral Element Method in Nek5000

At the beginning of the last decade, Petascale supercomputers (i.e., computers capable of more than 1 petaFLOP) emerged. Now, at the dawn of exascale supercomputing, we provide a review of recent landmark simulations of portions of reactor components with turbulence-resolving techniques that this computational power has made possible. In fact, these simulations have provided invaluable insight into flow dynamics, which is difficult or often impossible to obtain with experiments alone. We focus on simulations performed with the spectral element method, as this method has emerged as a powerful tool to deliver massively parallel calculations at high fidelity by using large eddy simulation or direct numerical simulation. We also limit this paper to constant-property incompressible flow of a Newtonian fluid in the absence of other body or external forces, although the method is by no means limited to this class of flows. We briefly review the fundamentals of the method and the reasons it is compelling for the simulation of nuclear engineering flows. We review in detail a series of Petascale simulations, including the simulations of helical coil steam generators, fuel assemblies, and pebble beds. Even with Petascale computing, however, limitations for nuclear modeling and simulation tools remain. In particular, the size and scope of turbulence-resolving simulations are still limited by computing power and resolution requirements, which scale with the Reynolds number. In the final part of this paper, we discuss the future of the field, including recent advancements in emerging architectures such as GPUbased supercomputers, which are expected to power the next generation of high-performance computers.

computational fluid dynamics↗

DOE OSTI2023

A new coupling of a GPU-resident large-eddy simulation code with a multiphysics wind turbine simulation tool

The development of new wind farm control strategies can benefit from combined analysis of flow dynamics in the farm and the behavior of individual turbines within one simulation environment. In this work, we present such an environment by developing a new coupling between the large-eddy simulation (LES) code GRASP and the multiphysics wind turbine simulation tool OpenFAST via an actuator line model (ALM). In addition, the implementation of the recently proposed filtered actuator line model (FALM) within the coupling is described. The new ALM implementation is cross-verified with results from four other commonly used research LES codes. The results for the blade loads and the near wake obtained with the new coupling are consistent with the other codes. Deviations are observed in the far wake. The results further indicate that the FALM is able to reduce the lift and power overprediction from which the traditional ALM suffers on coarse LES grids. This new simulation environment paves the way for future wind farm simulations under realistic weather conditions by leveraging GRASP's ability to impose data from large-scale meteorological models as boundary conditions.

17 WIND ENERGY↗

DOE OSTI2022

Large-Eddy Simulation of a wind turbine using a Filtered Actuator Line Model

When dealing with multirotor devices such as quadcopters or wind farms, the cost of blade-resolved large-eddy simulation (LES) becomes prohibitive. Combining LES with a family of lower-fidelity models, called actuator line models (ALMs), has grown in popularity in the past decade. ALM replaces full blade resolution with an array of actuator points or lines parameterized by aerodynamic lift/drag polar plots along the blades. Body forces computed based on these actuator points are then projected onto the LES flow mesh, mimicking the effect of rotating blades on the flow. However, the optimal projection radius and the associated LES grid size is often too restrictive for multirotor simulations. Recently, a new tip-correction-based filtered ALM (F-ALM) was proposed by Martinez-Tossas and Meneveau (2019), which allows coarser-than-optimal grids by avoiding the associated overprediction of thrust. In this work, F-ALM is implemented into a high-order, in-house LES code to simulate National Renewable Energy Laboratory Phase VI wind turbine. It is then followed by a comparison between the baseline ALM and the newly implemented F-ALM in terms of instantaneous and time-averaged flow fields and blade loads, revealing the advantages of F-ALM in preventing the overprediction of power on coarse grids. Finally, this encourages accurate and affordable simulations of multirotor devices in the future.

17 WIND ENERGY↗

DOE OSTI2024

Validation of the stochastic inversion algorithm for acoustic travel-time tomography: a large eddy simulation study

Acoustic tomography (AT) is explored as a remote sensing technique to obtain instantaneous snapshots of temperature and velocity fluctuations for wind energy applications. This study integrates Large Eddy Simulation (LES) with the Stochastic Inversion (SI) method to validate the algorithm’s capacity for accurate reconstruction of atmospheric fluctuations. The initial findings demonstrate the efficacy of the method in accurately capturing the predominant flow structures. Normalized L2 error evaluations further inform the algorithm’s precision, with errors accentuated in less sampled peripheral regions. The results underscore the method’s promise as a non-intrusive observational tool, with ongoing development poised to improve its precision and reliability.

17 WIND ENERGY↗

DOE OSTI2024

A numerical study of ignition and flame development characteristics in GCI combustion using large eddy simulations and chemical explosive mode analysis

Here, this work investigates the ignition and flame development processes of low reactivity fuel combustion under compression ignition conditions based on the large eddy simulation approach. The chemical explosive mode analysis (CEMA) is employed to characterize the local combustion features, including gas-liquid fuel zone, auto-ignition, diffusion-assisted, extinction, cool flame and post-ignition zone, among which auto-ignition and post-ignition are found to play a key role in the overall heat release process. The local flame propagation modes in gasoline compression ignition (GCI) are determined by quantifying the relative magnitude of diffusion/chemistry at a representative progress variable in the pre-ignition zone. The results show that autoignition fronts and deflagration waves exist simultaneously in the ignition and intense high temperature heat release (HTHR) stages, but autoignition fronts dominate. In addition, the chemical kinetic processes of four heat release periods are analyzed. The heat release during the ignition period is found to be dominated by the reactions CH 3 + H (+M) <=> CH 4 (+M) and CH 3 CHO + H <=> CH 2 CHO + H 2 . The reaction CH 2 OH + OH <=> CH 2 O + H 2 O always plays an important role in the heat releases during the other three combustion stages including intense HTHR, moderate HTHR and post-combustion.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Toward prediction of turbulent atmospheric flows over propagating oceanic waves via machine-learning augmented large-eddy simulation

Wind-wave interactions have important effects on the energy harvesting of offshore wind farms. High-fidelity large-eddy simulation (LES) is a powerful approach for investigating wind-wave interactions in turbulent oceanic environments. Due to the large scale of the flow domain and the high grid resolution required to resolve multi-scale flow motions, however, brute-force LES of wind-wave interactions is computationally very expensive. We propose augmenting brute-force LES via machine-learning data-driven modeling (ML-LES) to dramatically reduce the computational time required to obtain converged turbulence statistics when the brute-force approach is employed. Namely, we employ a convolutional neural network (CNN) autoencoder trained and validated with LES data sets to develop a highly efficient ML-LES approach for computing turbulence statistics from just a few snapshots of instantaneous LES flow fields. Further, our results demonstrate the accuracy and efficiency of ML-LES in predicting the mean velocity, velocity fluctuations, and turbulence kinetic energy in highly stretched computational grid systems required to carry out simulations in real-life oceanic environments.

42 ENGINEERING↗

DOE OSTI2024

Large eddy simulation of lean blow-off in swirl-stabilized flame with the subgrid dissipation concept

The lean blow-off mechanism of the premixed swirl flame is numerically investigated by large eddy simulation (LES) with the subgrid dissipation concept (SDC) combustion model. Three simulated cases cover stable, near blow-off, and transient conditions. Compared with the experiment, the LES-SDC approach captures the flow and combustion features for stable and near blow-off conditions. More importantly, the predictions of the blowoff procedure and duration agree satisfactorily with the experiment, indicating that the LES-SDC approach is a promising tool for predicting strong, unsteady turbulent combustion processes. Further, the numerical results are used to investigate the blow-off mechanism. Two stages in the blow-off procedure are specified. The first is the necking and extinction of the downstream flame surface, and the second is the shrinking of the upstream flame surface. The blow-off mechanism is well explained by the theory of stretched flame extinction. At the end of the recirculation zone, the large negative radial velocity pushes the flame to the central line. The combustion process here can be abstracted as the stretched counter-flame of the reactant-reactant configuration. The excessive flame stretch dominates the flame extinction and triggers the blow-off event. The upstream flame resists the intense stretch with the help of hot product recirculation, and the combustion here can be idealized as the counter-flame of the reactant-product configuration. The alignment of the temperature gradient and flow velocity, together with the excessive stretch, clearly indicates the tendency of flame local extinction. A Damköhler number-based blow-off criterion is raised from the mean flow strain rate and laminar flame bulk extinction strain rate.

42 ENGINEERING↗

DOE OSTI2025

A Large-Eddy Simulation Study in WRF on Wind over Broadband Waves of Different Directions and Spreading Widths

We use the Weather Research and Forecasting (WRF) Model coupled with moving waves to conduct large-eddy simulations (LESs) of wind over broadband waves with different propagating directions and spreading widths. Our results show that wind-opposing waves can double the form drag, and the wave propagating direction affects the mean wind velocity, velocity variances, and pressure stress. On the other hand, waves with wider spread tend to reduce the form drag in the streamwise direction. Results further indicate that the wave direction can impact the bulk drag coefficient by as much as 25%, while the wave directional spreading width can change it by 5%. Based on our wave-phase-resolved simulations, we demonstrate that the parameterization of sea surface roughness is significantly influenced by the direction of wave propagation relative to the wind, a factor that the commonly used Charnock relation does not account for.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

The role of cool-flame fluctuations in high-pressure spray flames, studied using high-speed optical diagnostics and Large-Eddy Simulations

Here this work investigates the low- and high-temperature ignition and combustion processes, applied to the Engine Combustion Network Spray A flame, combining advanced optical diagnostics and large-eddy simulations (LES). Simultaneous high-speed (50 kHz) formaldehyde (CH 2 0) planar laser-induced fluorescence (PLIF) and line-of-sight OH* chemiluminescence imaging were used to measure the low- and high-temperature flame, during ignition as well as during quasi-steady combustion. While tracking the cool flame at the laser sheet plane, the present experimental setup allows detection of distinct ignition spots and dynamic fluctuations of the lift-off length over time, which overcomes limitations for flame tracking when using schlieren imaging. After significant development to improve LES prediction of the low-and high-temperature flame position, both during the ignition processes and quasi-steady combustion, the simulations were analyzed to gain understanding of the mixture variance and how this variance affects formation/consumption of CH 2 0. Analysis of the high-temperature ignition period shows that a key improvement in the LES is the ability to predict heterogeneous ignition sites, not only in the head of the jet, but in shear layers at the jet edge close to the position where flame lift-off eventually stabilizes. The LES analysis also shows concentrated pockets of CH 2 0, in the center of jet and at 20 mm downstream of the injector (in regions where the equivalence ratio is greater than 6), that are of similar length scale and frequency as the experiment (approximately 5–6 kHz). The periodic oscillation of CH 2 0 match the frequency of pressure waves generated during auto-ignition and reflected within the constant-volume vessel throughout injection. The ability of LES to capture the periodic appearance and destruction of CH 2 0 is particularly important because these structures travel downstream and become rich premixed flames that affect soot production.

42 ENGINEERING↗

DOE OSTI2020

Laminar-to-turbulent flame transition and cycle-to-cycle variations in large eddy simulation of spark-ignition engines

This paper investigates the effect of laminar-to-turbulent flame transition modeling on the prediction of cycle-to-cycle variations (CCVs) in large eddy simulation (LES) of spark-ignition (SI) engines. A laminar-to-turbulent flame transition model that describes the non-equilibrium sub-filter flame speed evolution during an early stage of flame kernel growth is developed. In the present model, the flame transition is characterized by the flame kernel size at which the flame transition ends, defined here as the flame transition scale. The proposed model captures the effects that variations in a turbulent flow field have on the evolution of early-stage burning rates, through variations in the flame transition scale. The proposed flame transition model is combined with the front propagation formulation (FPF) method and a spark-ignition model to predict CCVs in a gasoline direct injection SI engine. It is found that multi-cycle LES with the proposed flame transition model reproduces experimentally-observed CCVs satisfactorily. When the transition model is not considered or when variations in the transition process are neglected, CCVs are significantly under-predicted for the case considered here. These results indicate the importance of modeling the laminar-to-turbulent flame transition and the effect of turbulence on the transition process, when predicting CCVs, under certain engine conditions. The LES results are also used to analyze sources for variations in the flame transition. It is found, for the present engine case, that the most important source is the cycle-to-cycle variation in the turbulence dissipation rate, which is used to measure the strength of turbulence in the proposed model, near a spark plug. The large-scale velocity field and the variations of the laminar flame speed due to the mixture composition and thermal stratification are also found to be important factors to contribute to the variations in the flame transition.

42 ENGINEERING↗

DOE OSTI2023

Grid resolution requirement of chemical explosive mode analysis for large eddy simulations of premixed turbulent combustion

Full Article Figures & data References Citations Metrics Reprints & Permissions Read this article Abstract The grid resolution requirement for trustworthy Chemical Explosive Mode Analysis (CEMA) in Large Eddy Simulation (LES) of premixed turbulent combustion is proposed. Explicit filtering, to emulate the effect of the LES filter, is applied to one-dimensional laminar flame and three-dimensional planar turbulent flames across a wide range of Karlovitz numbers (5 - 239). The identification of the flame front by CEMA is found relatively insensitive to the cell size (Δ), while the combustion mode identification shows more significant sensitivity. Specifically, increasing Δ falsely enhances the auto-ignition and local extinction modes and suppresses the diffusion-assisted mode. Limited dependence of the CEMA performance on the turbulent combustion regime (Karlovitz number) is observed. A simple grid size criterion for reliable CEMA mode identification in LES is proposed as Δ ≲ δ L /2; The criterion can be relaxed to Δ ≲ δ L in the laminar flame limit. Furthermore, theoretical analysis is conducted on an idealised chemistry-diffusion system. The effects of the filtering process and turbulence on the local combustion mode are demonstrated, which is consistent with the numerical observations. Further, by incorporating turbulent combustion models in CEMA, potential improvement in identifying local combustion modes can be expected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

JHTDB-wind: a web-accessible large-eddy simulation database of a wind farm with virtual sensor querying

This paper introduces JHTDB-wind (https://turbulence.idies.jhu.edu/datasets/windfarms, last access: 11 November 2025), a publicly accessible database containing large-eddy simulation (LES) data from wind farms. Building on the framework of the Johns Hopkins Turbulence Database (JHTDB), which hosts direct numerical simulation (DNS) and some LES datasets of canonical turbulent flows, JHTDB-wind stores the 4D space–time history of the flow and provides users the ability to access and query the data via a web-based virtual sensor interface. The initial dataset comprises LES results from a large wind farm with 10×6 turbines, modeled using a filtered actuator line method, under conventionally neutral atmospheric conditions. These data comprise 1 h (hour) of flow field data (velocity, pressure, potential temperature deviation, subgrid-scale (SGS) eddy viscosity, and turbine forces, approximately 15 TB (terabytes) and wind turbine data – including both turbine-level operational quantities and blade-level aerodynamic quantities (approximately 1.3 TB) – stored in Zarr and Parquet formats, respectively. Data retrieval is facilitated by the giverny Python package, allowing remote users to query the database in Python or MATLAB (C and Fortran support are available for flow field data). This paper details the simulation setup and demonstrates data access through examples that analyze wind farm flow structures and turbine performance. The framework is extensible to future datasets, including the JHTDB-wind diurnal cycle simulation analyzed in Xiao et al. (2025).

17 WIND ENERGY↗

DOE OSTI2023

Analysis of ducted fuel injection at high-pressure transcritical conditions using large-eddy simulations

Ducted fuel injection (DFI) is a proposed fuel injection concept for achieving substantial reductions in emissions. In this concept, the fuel is injected through a coannular duct, resulting in increased fuel-air mixing and minimized formation of soot and other unwanted combustion products. Apart from comprehensive experimental investigations on DFI, so far computational studies have been limited to single-point Reynolds-averaged Navier Stokes simulations. Therefore, the objective of this work is to complement these studies by performing large-eddy simulations using a diffuse-interface method to examine the physical mechanisms and combustion processes of DFI, specifically focusing on the mixing process and the effect of fuel-ducting on combustion and pollutant emissions. To this end, finite-rate chemistry simulations are performed of the DFI configuration corresponding to the Engine Combustion Network Spray A injector at transcritical conditions (n-dodecane fuel, 60 bar pressure and 1000 K temperature chamber conditions). A two-equation soot model is employed for the qualitative analysis of soot emissions. Direct comparisons of averaged and instantaneous flow field results with the Spray A configuration are performed to assess the effect of DFI on the first- and second-stage ignition and soot formation. Compared to the free-spray condition, the results show that the DFI case exhibits a combination of (i) increased mass flow rate and entrained air, (ii) larger pressure drop magnitude and flow velocity, and (iii) a closer-to-stoichiometric mixture composition (both globally and locally), each of which is conjectured to contribute toward reduced soot production.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2024

Large-Eddy Simulation Study of Flow and Combustion Dynamics in a Full-Scale Hydrogen–Air Rotating Detonation Combustor-Stator Integrated System

In the present work, a first-of-its-kind three-dimensional (3D) large-eddy simulation (LES) study is conducted to numerically investigate the combustion dynamics as well as aero-thermal phenomena in a full-scale nonpremixed hydrogen–air rotating detonation engine (RDE) (with a diverging-shaped lower-end wall), when integrated with nozzle guide vanes (NGV) acting as the turbine stator. The wall-modeled LES framework incorporates hydrogen–air detailed chemical kinetics and adaptive mesh refinement (AMR). A comparative analysis is carried out for two operating conditions with different fuel/air mass flow rates but global equivalence ratio of unity, and considering RDE configurations without and with stator. The LES model is validated against available experimental data for the low mass flux condition with respect to detonation wave speed/height, wave dynamics, and axial static pressure distribution. Numerical results indicate significant deflagrative combustion occurring in the fill region near the inner wall due to formation of recirculation zones in the injection near-field driven by the backward facing step. The leading detonation wave is found to be trailed by an azimuthal reflected-shock combustion (ARSC) wave, consistent with experimental observations, which consumes unburned vitiated reactants that leak through the main detonation wave. The main detonation wave characteristics, such as detonation wave speed/height and combustion efficiency, do not change appreciably with the presence of NGV. A novel combustion diagnostic technique based on chemical explosive mode analysis (CEMA) is employed to quantify the fraction of heat release occurring in the detonative mode versus deflagrative mode for the simulated conditions. The exit flow is found to be nearly fully subsonic and supersonic for the low and high mass flux conditions, respectively. Further analysis of the exit flow profiles shows that the presence of NGV renders the flow more axial and significantly impacts the exit Mach number and total pressure, while the total temperature shows negligible change. In addition, the low mass flux operating point, despite exhibiting more deflagrative losses within the combustor, yields overall lower pressure drop from plenum to exhaust, which is mainly attributed to lower pressure drop across the injectors. Lastly, the rotating detonation engine-nozzle guide vanes (RDE-NGV) configuration exhibits higher total pressure loss compared to rotating detonation engine (RDE) without stator across both the mass flux conditions. In conclusion, this study extends the state-of-the-art in numerical modeling of pressure gain combustion (PGC) systems by demonstrating high-fidelity 3D reacting LES of full-scale RDE-NGV systems relevant to RDE-turbine integration for stationary power generation.

Combustion↗

DOE OSTI2023

Large-Eddy Simulation of Flow Over Boeing Gaussian Bump Using Multiagent Reinforcement Learning Wall Model: Preprint

We develop a wall model for large-eddy simulation (LES) that takes into account various pressure-gradient effects using multi-agent reinforcement learning. The model is trained using low-Reynolds-number flow over periodic hills with agents distributed on the wall at various computational grid points. It utilizes a wall eddy-viscosity formulation as the boundary condition to apply the modeled wall shear stress. Each agent receives states based on local instantaneous flow quantities at an off-wall location, computes a reward based on the estimated wall-shear stress, and provides an action to update the wall eddy viscosity at each time step. The trained wall model is validated in wall-modeled LES of flow over periodic hills at higher Reynolds numbers, and the results show the effectiveness of the model on flow with pressure gradients. The analysis of the trained model indicates that the model is capable of distinguishing between the various pressure gradient regimes present in the flow. To further assess the robustness of the developed wall model, simulations of flow over the Boeing Gaussian bump are conducted at a Reynolds number of 2 x 10^6, based on the free-stream velocity and the bump width. The results of mean skin friction and pressure on the bump surface, as well as the velocity statistics of the flow field, are compared to those obtained from equilibrium wall model (EQWM) simulations and published experimental data sets. The developed wall model is found to successfully capture the acceleration and deceleration of the turbulent boundary layer on the bump surface, providing better predictions of skin friction near the bump peak and exhibiting comparable performance to the EQWM with respect to the wall pressure and velocity field. We also conclude that the subgrid-scale model is crucial to the accurate prediction of the flow field, in particular the prediction of separation.

boundary layer↗