Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “kapton”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Effects of Electrons, Protons, and Ultraviolet Radiation on Thermophysical Properties of Polymeric Films

The response of coated thin polymer films to ultraviolet (UV), electron and proton radiation simultaneously has been evaluated, with selected measurements in situ. Exposure was intended to simulate the electron and proton radiation environment near the Earth-Sun Lagrangian points (LI and L2) for five years and approximately 1000 equivalent solar hours (ESH) UV. These orbital environments are relevant to several potential missions such as the Next Generation Space Telescope and Geomagnetic Storm Warning, both of which may use thin film based structures for a sunshade and solar sail, respectively. The thin film candidates (12.5 micrometers thick) consisted of commercially available materials (Kapton(R) E, HN, Upilex(R) S, CP-1, CP-2, TOR-RC, and TOR-LMBP) that were metalized on one side with vapor deposited aluminum. All of the films are aromatic polyimides, with the exception of TORLMBP, which is a copoly(arylene ether benzimidazole). The films were exposed as second surface mirrors and the effects of the exposure on solar absorptance, thermal emittance, and tensile properties were determined. The in situ changes in solar absorptance from Kapton(R) and Upilex(R) were less than 0. 1, whereas the solar absorptance of TOR and CP films increased by more than 0.3 without saturating. The thermal emittance measurements also showed that the Kapton(R) and Upilex(R) materials increased only 1-2%, but the remaining materials increased 5-8%. Based on tensile property measurements made in air following the test, the failure stress of every type of polymer film decreased as a result of irradiation. The polymers most stable in reflectance, namely Upilex(R) and Kapton(R), were also the strongest in tension before irradiation, and they retained the greatest percentage of tensile strength. The films less stable in reflectance were also weaker in tension, and lost more tensile strength as a result of irradiation. The apparent failure strain (as a percent of original gage length) of every type of polymer film except TOR-RC, decreased as a result of irradiation.

Russell, Dennis A.↗
NASA NTRS2006

MISSE Scattered Atomic Oxygen Characterization Experiment

An experiment designed to measure the atomic oxygen (AO) erosion profile of scattered AO was exposed to Low Earth Orbital (LEO) AO for almost four years as part of the Materials International Space Station Experiment 1 and 2 (MISSE 1 and 2). The experiment was flown in MISSE Passive Experiment Carrier 2 (PEC 2), Tray 1, attached to the exterior of the International Space Station (ISS) Quest Airlock. The experiment consisted of an aperture disk lid of Kapton H (DuPont) polyimide coated on the space exposed surface with a thin AO durable silicon dioxide film. The aperture lid had a small hole in its center to allow AO to enter into a chamber and impact a base disk of aluminum. The AO that scattered from the aluminum base could react with the under side of the aperture lid which was coated sporadically with microscopic sodium chloride particles. Scattered AO erosion can occur to materials within a spacecraft that are protected from direct AO attack but because of apertures in the spacecraft the AO can attack the interior materials after scattering. The erosion of the underside of the Kapton lid was sufficient to be able to use profilometry to measure the height of the buttes that remained after washing off the salt particles. The erosion pattern indicated that peak flux of scattered AO occurred at and angle of approximately 45 from the incoming normal incidence on the aluminum base unlike the erosion pattern predicted for scattering based on Monte Carlo computational predictions for AO scattering from Kapton H polyimide. The effective erosion yield for the scattered AO was found to be a factor of 0.214 of that for direct impingement on Kapton H polyimide.

Banks, Bruce A.↗
DOE OSTI2025

Chain Flexibility and Structure of a Polyimide Copolymer: Revisiting the Freely Rotating Chain Model

Poly(4–4′-oxydiphenylene-pyromellitimide)-based polyimides─trade name Kapton─have wide-ranging engineering applications owing to their thermal and mechanical stability, but little is known about underlying chain-level characteristics. While theoretical models have conceptualized Kapton as inflexible polycyclic rods separated by freely rotating diphenyl ether hinge groups, the model’s core predictions remain untested and subtleties of the relaxation behavior are missed, which atomistic modeling can resolve. To these ends, we examine all-atom Kapton structures in crystalline and glassy amorphous configurations using a DFT-validated class II force field. Constructing amorphous configurations is challenging, as the fused-ring-containing backbone has slow relaxation dynamics and scaling suggestive of entanglements even in oligomers. In conclusion, we find larger backbone rearrangements of the linear polycyclic segments about ether groups that are consistent with the rod-hinge picture on the monomer scale, whereas a ring rotation analysis suggests partially flexible rod-like segments and involves multiple facile rotational relaxation modes.

Liesen, Nicholas T. [Lawrence Livermore National L↗
NASA NTRS1971

Investigation of the feasibility of developing low permeability polymeric films

The feasibility of reducing the gas permeability rate of Mylar and Kapton films without drastically effecting their flexibility characteristics at cryogenic temperatures was considered. This feasibility was established using a concept of diffusion bonding two layers of metallized films together forming a film-metal-film sandwich laminate. The permeability of kapton film to gaseous helium was reduced from a nominal ten = to the minus 9 power cc-mm/sq cm sec. cm Hg to ten to the minus 13 power cc-mm/ sq cm - sec. cm Hg with some values as low as ten to the minus 15 power cc - mm/sq cm m-sec - cm Hg being obtained. Similar reductions occurred in the liquid hydrogen permeability at -252 C. In the course of the program the permeability, flexibility and bond strength of plain, metalized and diffusion bond film were determined at +25 C, -195 C and -252 C. The cryogenic flexibility of Kapton film was reduced slightly due to the metallization process but no additional loss in flexibility resulted from the diffusion bonding process.

Hoggatt, J. T.↗
NASA NTRS1975

Photoconductivity of high voltage space insulating materials: Measurements with metal electrodes

The electrical conductivities of high voltage insulating materials were measured in the dark and under various intensities of illumination. The materials investigated included FEP Teflon, Kapton-H, fused quartz, and parylene. Conductivities were determined as functions of temperature between 22 and 100 C and light intensity between 0 and 2.5 kW/m2. The thickness dependence of the conductivity was determined for Teflon and Kapton, and the influence of spectral wavelengths on the conductivity was determined in several cases. All measurements were made in a vacuum to simulate a space environment, and all samples had metallic electrodes. The conductivity of Kapton was permanently increased by exposure to light; changes as great as five orders of magnitude were observed after six hours of illumination.

Coffey, H. T.↗
NASA NTRS1977

Effects of illumination on the conductivity properties of spacecraft insulating materials

Experimental data on the dark and illuminated conductivities of Kapton V and polyvinylidene fluoride (PVF2) films are described as well as the changes in insulating properties produced in Kapton H, Kapton V, PVF2, and FEP Teflon films as result of prolonged exposure to solar illumination. An overall summary of the results of tests is presented. A general introduction and a description of the experimental apparatus and procedures used are also given.

Adamos, R. C.↗
NASA NTRS1980

Evaluation of charge control techniques on spacecraft thermal surfaces (electrostatic discharge study)

The charging and discharging characteristics of various dielectric materials commonly used on spacecraft were tested. The experimental apparatus and the calculations used to analyze the data generated during the testing are described. The test technique, results, and analysis used are presented. Indium tin oxide coated Teflon, Kapton, and quartz do not charge significantly. CTL 15 white paint shows no large charge build up. Pinholes in Teflon and Kapton increase the leakage through the sample and reduce the energy released in an arc. Conductive grids in Teflon and Kapton reduce the arc energy by two orders of magnitude over untreated samples. Extreme low temperatures (-195 C) do not significantly increase the arc energy of the gridded sample.

Robinson, P. A., Jr.↗
NASA NTRS1982

Oxygen atom reaction with shuttle materials at orbital altitudes

Surfaces of materials used in the space shuttle orbiter payload bay and exposed during STS-1 through STS-3 were examined after flight. Paints and polymers, in particular Kapton used on the television camera thermal blanket, showed significant change. Generally, the change was a loss of surface gloss on the polymer with apparent aging on the paint surfaces. The Kapton surfaces showed the greatest change, and postflight analyses showed mass loss of 4.8 percent on STS-2 and 35 percent on STS-3 for most heavily affected surfaces. Strong shadow patterns were evident. The greatest mass loss was measured on surfaces which were exposed to solar radiation in conjunction with exposure in the vehicle velocity vector. A mechanism which involves the interaction of atomic oxygen with organic polymer surfaces is proposed. Atomic oxygen is the major ambient species at low orbital altitudes and presents a flux of 8 x 10 to the 14th power atoms/cu cm sec for reaction. Correlation of the expected mass loss based on ground-based oxygen atom/polymer reaction rates shows lower mass loss of the Kapton than measured. Consideration of solar heating effects on reaction rates as well as the high oxygen atom energy due to the orbiter's orbital velocity brings the predicted and measured mass loss in surprisingly good agreement. Flight sample surface morphology comparison with ground based Kapton/oxygen atom exposures provides additional support for the oxygen interaction mechanism.

Leger, L. J.↗
NASA NTRS1982

Multi-100 kW: Planar low cost solar array development

The applicability of selected low cost options to solar array blanket design was studied by fabricating representative modules and submitting them to thermal cycle environment. Large area (5.9 x 5.9 cm) solar cells of 3 varieties were purchased: (1) Standard wraparound, (2) Copper contacts substituted for the conventional Titanium-Palladium-Silver, and (3) Standard wraparound except with gridded back contact instead of continuous metallization. The baseline cell was purchased to compare fabrication cost and to serve as a control cell during test evaluation of the other two cells. All cells were assembled into either substrate modules where the cell is individually filtered and welded to an integrated Kapton-copper circuit or into a superstrate configuration with 4 cells jointly adhered to a single sheet of microsheet and then welded to the integrated Kapton-copper circuit. Cell quality, particularly in the metallization of contacts, was less than desired. Problems were encountered with copper metallization in laying down a barrier metal which would ohmically bond to the silicon. The cells received were shunted (sintered) or with low contact pull strength (non-sintered), thus leading to the decision to solder rather than weld the copper cells to the Kapton substrate.

Source record↗
NASA NTRS1984

LEO atomic oxygen effects on spacecraft materials: STS-5 results

Effects of low Earth orbit (LEO) atomic oxygen were measured on a variety of spacecraft materials which obtained exposure on STS-5. Material degradation dependency on temperature was found in one material. Of the five paints flown, only S13GLO was unaffected. Generally, the glossy paints became Lambertian and the diffuse coatings improved. Scanning electron microscope examinations indicated removal of urethane and epoxy paint binder materials. Reaction products were evident on the surfaces of Z302 paint and Mylar. Thin films showed thickness losses ranging from negligible loss in Teflon to considerable loss in Mylar and Kapton. Glossy films such as black Kapton and white Tedlar became diffused. Kevlar 29 rope lost tensile strength and silver solar cell interconnect material oxidized. Oxidation on the backside of an elevated specimen indicated that reflections of oxygen atoms were occurring and that reflecting surfaces, probably Kapton, were not fully accommodating the incident atoms.

Whitaker, A. F.↗
NASA NTRS1986

Analyses of spacecraft polymeric materials

Partial analytical characterizations are made by four different techniques of three polymeric materials used in conjunction with the Space Telescope for samples flown on mission STS-8. The polymers were Tedlar, Kapton H, and Kapton F. The surfaces of the three polymers were attacked and oxidized by atomic oxygen, and fluorine is lost from the surface of Kapton F, largely due to displacement by atomic oxygen.

Worley, S. D.↗
NASA NTRS1985

Examination of returned solar-max surfaces for impacting orbital debris and meteoroids

The thermal insulation of the Solar Maximum Mission launched on 14 February 1980 which consisted of 17 layers of alumized Kapton offers an excellent opportunity to obtain chemistry of impacting particles. To date, approximately 0.7 sq. met. of the insulation and 0.05 sq. met. of the aluminum louvers have been mapped by optical microscope for crater diameters larger than 40 microns. Atomic oxygen has eroded up to 20 microns of the exposed Kapton surfaces removing the older and smaller craters. The crater size distribution found on 3 different Kapton surfaces is shown. About 250 chemical spectra were recorded of particles observed in or around impact pits or in the debris pattern found on the second layer beneath impact holes in the outer layer. The debris populations are listed and discussed.

Kessler, D. J.↗
NASA NTRS1987

Spectroscopic comparison of effects of electron radiation on mechanical properties of two polyimides

The differences in the radiation durabilities of two polyimide materials, Du Pont Kapton and General Electric Ultem, are compared. An explanation of the basic mechanisms which occur during exposure to electron radiation from analyses of infrared (IR) and electron paramagnetic resonance (EPR) spectroscopic data for each material is provided. The molecular model for Kapton was, in part, established from earlier modeling for Ultem (pp. 1293-1298 of IEEE Transactions on Nuclear Science, December 1984). Techniques for understanding the durability of one complex polymer based on the understanding of a different and equally complex polymer are demonstrated. The spectroscopic data showed that the primary radiation-generated change in the tensile properties of Ultem (a large reduction in tensile elongation) was due to crosslinking, which followed the capture by phenyl radicals of hydrogen atoms removed from gem-dimethyl groups. In contrast, the tensile properties of Kapton remained unchanged because radical-radical recombination, a self-mending process, took place.

Long, Edward R., Jr.↗
NASA NTRS1986

An evaluation of candidate oxidation resistant materials for space applications in LEO

Ground based testing of materials considered for polyimide (Kapton) solar array blanket protection and graphite-epoxy stroctural member protection was performed in an RF plasma asher. Protective coatings on Kapton from various commercial sources and from NASA Lewis Research Center were exposed to the air plasma; and mass loss per unit area was measured for each sample. All samples evaluated provided some protection to the underlying surface, but metal-oxide-fluoropolymer coatings provided the best protection by exhibiting very little degradation after 47 hr of asher exposure. Mica paint was evaluated as a protective coating for graphite-epoxy structural members. Mica appeared to be resistant to attack by atomic oxygen, but only offered limited protection as a paint. this is believed to be due to the paint vehicle ashing underneath the mica leaving unattached mica flakes lying on the surface. The protective coatings on Kapton evaluated so far are promising but further research on protection of graphite-epoxy support structures is needed.

Rutledge, Sharon↗
NASA NTRS1987

Groundbased studies of spacecraft glow and erosion caused by impact of oxygen and nitrogen beams

To simulate surface reactions in the space environment a ground-based facility was developed that produces a very high flux 10(14) to 10(16)/sq cm/s of low energy (2 to 20 eV) neutral atoms and molecules. The neutral beams are created using a method involving neutralization and reflection of ions from a biased limiter, where the ions are extracted from a toroidal plasma source. The spectra of emission due to beam-solid interactions on targets of Chemglaze Z-306 optical paint and Kapton are presented. Erosion yields for carbon and Kapton targets with low energy (approx. 10 eV) nitrogen and oxygen beams were measured. The reaction rates and surface morphology for the erosion of Kapton are similar to those measured in experiments on STS-5.

Langer, W. D.↗
NASA NTRS1987

An evaluation of candidate oxidation resistant materials

Ground based testing of materials considered for Kapton solar array blanket protection, graphite epoxy structural member protection, and high temperature radiators was performed in an RF plasma asher. Ashing rates for Kapton were correlated with rates measured on STS-8 to determine the exposure time equivalent to one year in low Earth orbit (LEO) at a constant density space station orbital flux. Protective coatings on Kapton from Tekmat, Andus Corporation, and LeRC were evaluated in the plasma asher and mass loss rates per unit area were measured for each sample. All samples evaluated provided some protection to the underlying surface but ion beam sputter deposited samples of SiO2 and SiO2 with 8% polytetrafluoroethylene (PTFE) showed no evidence of degradation after 47 hours of exposure. Mica paint was evaluated as a protective coating for graphite epoxy structural members. Mica appears to be resistant to attack by atomic oxygen but only offers some limited protection as a paint because the paint vehicles evaluated to date were not resistant to atomic oxygen. Four materials were selected for evaluation as candidate radiator materials: stainless steel, copper, niobium-1% zirconium, and titanium-6% aluminum-4% vanadium. These materials were surface textured by various means to improve their emittance. Emittances as high as 0.93 at 2.5 microns for stainless steel and 0.89 at 2.5 microns for Nb-1 Zr were obtained from surface texturing. There were no significant changes in emittance after asher exposure.

Rutledge, Sharon↗
NASA NTRS1986

Electron-radiation effects on the ac and dc electrical properties and unpaired electron densities of three aerospace polymers

The effects of gigarad-level total absorbed doses from 1-MeV electrons on the post-irradiation alternating-current (ac) and direct-current (dc) electrical properties and the unpaired electron densities have been studied for Kapton, Ultem, and Mylar. The unpaired electron densities (determined from electron paramagnetic resonance spectroscopy) and the dc electrical conductivities of the irradiated materials were monitored as functions of time following the exposures to determine their decay characteristics at room temperature. The elevated-temperature ac electrical dissipations of the Ultem and Mylar were affected by the radiation. The dc conductivity of the Kapton increased by five orders of magnitude, while the dc conductivities of the Ultem and Mylar increased by less than an order of magnitude, due to the radiation. The observed radiation-generated changes in the ac electrical dissipations are explained in terms of known radiation-generated changes in the molecular structures of the three materials. A preliminary model relating the dc electrical conductivity and the unpaired electron density in the Kapton is proposed.

Long, Sheila Ann T.↗
NASA NTRS1987

Degradation mechanisms of materials for large space systems in low Earth orbit

Degradation was explored of various materials used in aerospace vehicles after severe loss of polymeric material coatings (Kapton) was observed on an early shuttle flight in low Earth orbit. Since atomic oxygen is the major component of the atmosphere at 300 km, and the shuttle's orbital velocity produced relative motion corresponding to approx. 5 eV of oxygen energy, it was natural to attribute much of this degradation to oxygen interaction. This assumption was tested using large volume vacuum systems and ion beam sources, in an exploratory effort to produce atomic oxygen of the appropriate energy, and to observe mass loss from various samples as well as optical radiation. Several investigations were initiated and the results of these investigations are presented in four papers. These papers are summarized. They are entitled: (1) The Space Shuttle Glow; (2) Laboratory Degradation of Kapton in a Low Energy Oxygen Ion Beam; (3) The Energy Dependence and Surface Morphology of Kapton Degradation Under Atomic Oxygen Bombardment; and (4) Surface Analysis of STS 8 Samples.

Gordon, William L.↗