SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Hydrogen isotherms have been measured for activated LaNi(sub 4.6)M(sub 0.4) alloys from 300 K to 473 K or 493 K, where M= Si, Ge, Sn. Thermodynamic parameters have been obtained from the isotherms using van't Hoff plots for hydride decomposition.
The isothermal oxidation kinetics of as-cast Cu-17%Cr and Cu-17%Cr-5%Al in air were studied between 773 and 1173 K under atmospheric pressure. These observations reveal that Cu-17%Cr-5%Al oxidizes at significantly slower rates than Cu-17%Cr. The rate constants for the alloys were determined from generalized analyses of the data without an a priori assumption of the nature of the oxidation kinetics. Detailed analyses of the isothermal thermogravimetric weight change data revealed that Cu-17%Cr exhibited parabolic oxidation kinetics with an activation energy of 165.9+/-9.5 kJ/mol. In contrast, the oxidation kinetics for the Cu-17%Cr-5%Al alloy exhibited a parabolic oxidation kinetics during the initial stages followed by a quartic relationship in the later stages of oxidation. Alternatively, the oxidation behavior of Cu-17%CR-5%Al could be better represented by a logarithmic relationship. The parabolic rate constants and activation energy data for the two alloys are compared with literature data to gain insights on the nature of the oxidation mechanisms dominant in these alloys.
The isothermal oxidation kinetics of as-cast Cu-17%Cr and Cu-17%Cr-5%Al in air were studied between 773 and 1173 K under atmospheric pressure. These observations reveal that Cu- 17%Cr-5%Al oxidizes at significantly slower rates than Cu-17%Cr. The rate constants for the alloys were determined from generalized analyses of the data without an a priori assumption of the nature of the oxidation kinetics. Detailed analyses of the isothermal thermogravimetric weight change data revealed that Cu-17%Cr exhibited parabolic oxidation kinetics with an activation energy of 165.9 +/- 9.5 kJ/mol. In contrast, the oxidation kinetics for the Cu-17%Cr- 5%Al alloy exhibited a parabolic oxidation kinetics during the initial stages followed by a quartic relationship in the later stages of oxidation. Alternatively, the oxidation behavior of Cu-17%CR- 5%Al could be better represented by a logarithmic relationship. The parabolic rate constants and activation energy data for the two alloys are compared with literature data to gain insights on the nature of the oxidation mechanisms dominant in these alloys.
The isothermal oxidation kinetics of as-cast Cu-17%Cr and Cu-17%Cr-5%Al in air were studied between 773 and 1173 K under atmospheric pressure. These observations reveal that Cu- 17%Cr-5%Al oxidizes at significantly slower rates than Cu-17%Cr. The rate constants for the alloys were determined from generalized analyses of the data without an a priori assumption of the nature of the oxidation kinetics. Detailed analyses of the isothermal thermogravimetric weight change data revealed that Cu-17%Cr exhibited parabolic oxidation kinetics with an activation energy of 165.9 9.5 kJ mol-1. In contrast, the oxidation kinetics for the Cu-17%Cr- 5%Al alloy exhibited a parabolic oxidation kinetics during the initial stages followed by a quartic relationship in the later stages of oxidation. Alternatively, the oxidation behavior of Cu-17%CR- 5%Al could be better represented by a logarithmic relationship. The parabolic rate constants and activation energy data for the two alloys are compared with literature data to gain insights on the nature of the oxidation mechanisms dominant in these alloys.
To meet future demand for single-aisle composite aircraft production, manufacturing rates are expected to increase by up to six times current production rates. Resin infusion is a manufacturing method that has potential to enable fabrication of structures at the desired rates. However, production cycle times with currently available commercial infusion resins cannot support the rates needed for an estimated 80 aircraft per month. Recently, rapid-curing isothermal resins were developed that can reduce the overall processing time. These resins can be infused, cured, and demolded at a single temperature below 100 °C, thereby eliminating the need for time consuming temperature ramps and shortening the overall cure time. In addition, the low temperatures enable use of low-cost tooling during production. This presentation will discuss the use of resin transfer molding to produce composites with rapid-curing isothermal resins, manufacturing considerations, and performance characteristics of the composites.
Cementitious reagents are used to solidify/stabilize aqueous radioactive, hazardous, and mixed salt solutions, and sludges to meet low-level radioactive waste (LLW) and Resource Conservation and Recovery Act (RCRA) requirements for disposal at Department of Energy (DOE). It is flexible enough to solidify radioactive wastewater saturated in complex species that include but are not limited to radioactive isotopes from the bombardment of neutrons in reactor operation, corrosion products from metallic components, and a variety of soluble organic compounds. [1,2]. Waste form testing typically includes processing or fresh properties, cured properties, compressive strength and hydraulic properties, porosity, density, saturated and unsaturated moisture transport, and leachability of contaminants in the waste form pore solution. Properties are collected over a relatively limited time, typically 28 to 365 days [3]. In addition, changes in the waste form as the result of time and changing conditions are important for concrete engineers to predict overall performance of the forms and potential release of contaminants in the disposal process via unintended filtration into the environment [4]. These predictions are determined/calculated characterizing young waste forms (relative to the standard age of concrete) and are based on transport through soluble ions in pore solutions. Characterization methods include X-ray, SEM, and isothermal calorimetry among other methods used to define the composition, amorphous vs. crystalline nature of the components, and the energetic formation mechanisms for multi-phase mineral systems. [5–7] Isothermal calorimetry is a well standardized technique for cements and concretes and can be used to predict the timing and nature of the hydration reactions.[8] The technique can measure long term energetic
Electrocatalysts enable the efficient interconversion of electrical and chemical energy for the sustainable production of fuels and chemicals. Here, in this Comment, we highlight the importance of developing electrochemical adsorption isotherms to demystify complex reaction mechanisms and rationalize catalytic activity.
Thin film thickness from theoretical expressions for conductivity and isothermal Hall effect
Isothermal map of Proclus area of moon and description of map making methods
Physical adsorption isotherm based on triangular site model, including neighbor interactions via Lennard-Jones intermolecular potentials
Thermionic conversion system performance analysis based on space charge theory and isothermal diode sheath theory
Atlas of stratospheric mean isotherms derived from Tiros VII observations
Specific isothermal mass capacity of humid air for calculating mass transfer from colloidal capillary-porous body to surroundings
Isothermal and isophotic atlas of moon contours through lunation
Heat exchange with carbon dioxide along supercritical isotherms under free convection
Complete hydrogen isotherms have been measured using highly stoichiometric, activated LaNi5 over a wide temparature range, 373K to 228K.
Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.
Here, we report a strategy to accelerate the synthesis and increase the crystallinity of colloidal crystals engineered with DNA. Specifically, by holding the DNA-modified Au particle building blocks above the T m of the individual nanoparticle building blocks, but slightly below the T m of the anticipated colloidal crystal during the assembly process, crystallinity is increased, and enthalpically-favored phases with high degrees of facet registration are observed. We studied the utility of this approach with systems for which the commonly adopted slow-cooling approach yielded primarily amorphous aggregates. In particular, we used it to synthesize high-volume fraction colloidal crystals from large (80 nm) anisotropic nanoparticles (cubes and rhombic dodecahedra) with short (<14 nm) DNA designed to restrict the degrees of freedom for the DNA bonds and maintain the anisotropy of the particle building block. Small-angle X-ray scattering and electron microscopy studies show that the crystalline phases synthesized via this method are more thermally stable than their corresponding aggregate phases, likely due to an increased number of DNA-DNA bonds between particles. Crystal size tunability (between 0.5 and 15 µm edge lengths) and epitaxial growth were demonstrated using this strategy by modulating the NaCl concentration in tandem with previously synthesized colloidal crystal nuclei. Taken together, this isothermal strategy provides a route to deliberately crystallize a wide variety of anisotropic colloidal materials and expands the phase space accessible to nanoparticles modified with DNA.