Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “insertion loss.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

RF MEMS Switches with SiC Microbridges for Improved Reliability

Radio frequency (RF) microelectromechanical (MEMS) switches offer superior performance when compared to the traditional semiconductor devices such as PIN diodes or GaAs transistors. MEMS switches have a return loss (RL) better than -25 dB, negligible insertion loss (IL), isolation better than -30 dB, and near zero power consumption. However, RF MEMS switches have several drawbacks the most serious being long-term reliability. The ability for the switch to operate for millions or even billions of cycles is a major concern and must be addressed. MEMS switches are basically grouped in two categories, capacitive and metal-to-metal contact. The capacitive type switch consists of a movable metal bridge spanning a fixed electrode and separated by a narrow air gap and thin insulating material. The metal-to-metal contact type utilizes the same basic design but without the insulating material. After prolonged operation the metal bridges, in most of these switches, begin to sag and eventually fail to actuate. For the metal-to-metal type, the two metal layers may actually fuse together. Also if the switches are not packaged properly or protected from the environment moisture may build up and cause stiction between the top and bottom electrodes rendering them useless. Many MEMS switch designs have been developed and most illustrate fairly good RF characteristics. Nevertheless very few have demonstrated both great RF performance and ability to perform millions/billions of switching cycles. Of these, nearly all are of metal-to-metal type so as the frequency increases RF performance decreases.

Scardelletti, Maximilian C.↗
DOE OSTI2023

Scaling comb-driven resonator-based DWDM silicon photonic links to multi-Tb/s in the multi-FSR regime

The use of chip-based micro-resonator Kerr frequency combs in conjunction with dense wavelength-division multiplexing (DWDM) enables massively parallel intensity-modulated direct-detection data transmission with low energy consumption. Resonator-based modulators and filters used in such systems can limit the number of usable wavelength channels due to practical constraints on the maximum achievable free spectral range (FSR). In this work, we introduce the design of multi-Tb/s comb-driven resonator-based silicon photonic links by leveraging the multi-FSR regime. We demonstrate the viability of the link architecture with yield estimates that are supported by extensive wafer-scale measurements of 704 micro-resonators fabricated in a commercial complementary metal–oxide–semiconductor foundry. We show that a 2.80 Tb/s link is realizable with a ≥6 σ yield (∼99.999%), and that aggregate bandwidths of 3.76 Tb/s and 4.72 Tb/s are possible if yield targets are relaxed (3 σ and 1 σ , respectively). All designs represent a 1.94−3.28× boost to aggregate link bandwidth while maintaining BER≤10 −10 performance, with a theoretical bandwidth of 10.51 Tb/s being possible for sufficiently robust resonators. We use high-speed BER measurements to inform co-optimization of data rate and aggressor spacing ( λ ag ), limiting any additional loss-based power penalties to off-resonance insertion loss (IL) and routing loss. This work demonstrates that, through the multi-FSR regime, there is a clear path toward Kerr comb-driven ultra-broadband, high bandwidth silicon photonic links that can support next-generation data centers and high-performance computers.

James, Aneek (ORCID:0000000262527807)↗
NASA NTRS1987

Acoustic transmissibility of advanced turboprop aircraft windows

Advanced turboprop technology allows propeller aircraft to reach cruise speeds comparable to current jet aircraft yet with considerable fuel savings. Due to the higher blade loading and higher tip speed of these propellers, noise levels of up to 150 dB are expected on the outside of the fuselage in the propeller plane. In this study the transmissibility of triple pane windows, designed to provide 69 dB noise transmission loss at the blade propeller frequency of 164 Hz, was experimentally investigated using insertion loss and three-dimensional intensity techniques. A modal analysis on the outer window panes was conducted to determine pane modal frequencies. Coherence and phase relation of outer panes and window frame were established to obtain double/triple wall and lump mass resonance frequencies. Double/triple wall resonances were found to degrade the transmission loss of the two windows. It was shown that, at the blade passage frequency and the first two overtones, the combinations of window plus scratch shield provide less transmission loss than the average transmission loss of the treated fuselage. Strong disagreement was obtained between the experimental transmission loss of this investigation and the theoretical predictions from another study.

Grosveld, Ferdinand W.↗
NASA NTRS2008

Compact Low-Loss Planar Magic-T

This design allows broadband power combining with high isolation between the H port and E port, and achieves a lower insertion loss than any other broadband planar magic-T. Passive micro wave/millimeter-wave signal power is combined both in-phase and out-of-phase at the ports, with the phase error being less than 1 , which is limited by port impedance. The in-phase signal combiner consists of two quarter-wavelength-long transmission lines combined at the microstrip line junction. The out-of-phase signal combiner consists of two half-wavelength-long transmission lines combined in series. Structural symmetry creates a virtual ground plane at the combining junction, and the combined signal is converted from microstrip line to slotline. Optimum realizable characteristic impedances are used so that the magic-T provides broadband response with low return loss. The magic-T is used in microwave and millimeter-wave frequencies, with the operating bandwidth being approximately 100 percent. The minimum isolation obtainable is 32 dB from port E to port H. The magic-T VSWR is less than 1.1 in the operating band. Operating temperature is mainly dependent on the variation in the dielectric constant of the substrate. Using crystallized substrate, the invention can operate in an extremely broad range of temperatures (from 0 to 400 K). It has a very high reliability because it has no moving parts and requires no maintenance, though it is desirable that the magic-T operate in a low-humidity environment. Fabrication of this design is very simple, using only two metallized layers. No bond wires, via holes, or air bridges are required. Additionally, this magic-T can operate as an individual component without auxiliary components.

U-yen, Kongpop↗
NASA NTRS1986

A 30-GHz monolithic receiver

Several monolithic integrated circuits have been developed to make a 30-GHz receiver. The receiver components include a low-noise amplifier (LNA), an IF amplifier, a mixer, and a phase shifter. The LNA has a 7-dB noise figure with over 17 dB of associated gain. The IF amplifier has a 13-dB gain with a 30-dB control range. The mixer has a conversion loss of 10.5 dB. The phase shifter has a 180-deg phase shift control and a minimum insertion loss of 1.6 dB.

Liu, Louis C. T.↗
NASA NTRS1994

Adjustable Optical-Fiber Attenuator

Adjustable fiber-optic attenuator utilizes bending loss to reduce strength of light transmitted along it. Attenuator functions without introducing measurable back-reflection or insertion loss. Relatively insensitive to vibration and changes in temperature. Potential applications include cable television, telephone networks, other signal-distribution networks, and laboratory instrumentation.

Buzzetti, Mike F.↗
NASA NTRS2002

Experimental Analysis of Reduced-Sized Coplanar Waveguide Transmission Lines

An experimental investigation of the use of capacitive loading of coplanar waveguides to reduce their line length and, thus the size, of monolithic microwave integrated circuits is presented. The reduced sized coplanar waveguides are compared to unloaded transmission lines and to lumped element transmission line segments. The phase bandwidth, defined by 2 percent error in S(sub 21), and the return loss bandwidth, defined by a return loss greater than 15 dB, of coplanar waveguides reduced from 0 to 90 percent are compared, and the insertion loss as a function of the size reduction is presented.

Ponchak, George E.↗
NASA NTRS1992

Determination of the dissipative loss of a two-port network from noise temperature measurements

When radiometric equipment is available, noise temperature measurement techniques provide a convenient and accurate means for determining the dissipative component of the insertion loss of a two-port network. It is increasingly becoming the practice to ignore mismatch errors caused by multiple reflections between the source, the receiver, and the component whose dissipative loss is being measured. Mismatch errors are difficult to determine in practice because of the requirements of having full knowledge of the magnitudes of reflection coefficients and S-parameters. This article shows it is permissible to neglect the effects of mismatch errors if special conditions are met. These special conditions only require that the reflection coefficients of the source and load be made negligibly small and that the two-port network being evaluated has reciprocal and symmetrical properties.

Otoshi, T. Y.↗
NASA NTRS1991

Performance of a high T (sub c) superconducting ultra-low loss microwave stripline filter

Discussed here is the successful fabrication of a five-pole interdigital stripline filter made of the 93 K superconductor (Y1Ba2Cu3O sub y) coated on a silver substrate, with center frequency of 8.5 GHz and an extremely high rejection ratio of 80 dB. The lowest injection loss measured was 0.1 dB at 12 K, with a return loss of better than 16 dB, representing a significant improvement over a similar copper filter, and is comparable to low critical temperature filters. The insertion loss appears to be limited by extrinsic factors, such as tuning mismatch and joint losses, and not by superconducting material losses.

Bautista, J. J.↗
DOE OSTI2024

Low loss fiber-coupled volumetric interconnects fabricated via direct laser writing

Photonic integrated circuits (PICs) are vital for high-speed data transmission. However, optical routing is limited in PICs composed of only one or a few stacked planes. Further, coupling losses must be low in deployed systems. Previously, we developed the subsurface controllable refractive index via beam exposure (SCRIBE) technique to write accurate 3D gradient refractive index (GRIN) profiles within a mesoporous silica scaffold. Here, we apply SCRIBE to fabricate low loss, broadband, polarization insensitive, fiber-coupled, single-mode volumetric interconnects that include waveguides traversing arbitrary 3D paths. By seamlessly integrating mode-matching subsurface lenses and GRIN waveguide tapers, calibrating for positional writing errors, implementing multipass exposure, automating alignment, and switching to antireflection coated fibers, we reduced the insertion loss for a fiber-PIC-fiber interconnect from 50 to 2.14 dB, or 1.47 dB, excluding the fiber array’s loss. Further, we establish an upper bound of 0.45 dB loss per coupler. We report quality factors of 27,000 and 77,000 and bending losses of 6 and 3 dB/cm for 15 and 30 µm radii microrings, respectively. We also demonstrate Bézier escalators, polarization-rotating and polarization-splitting interconnects, and a seven-channel 25 µm pitch volumetric interconnect. The SCRIBE platform presents a clear path toward realizing 3D PICs with unique functionality.

Optics↗
NASA NTRS1991

Low loss waveguide four-port crossover circuit and its application for cross-slot antenna feed

A four-way crossover circuit using a cylindrical cavity with four rectangular input/output ports has been designed to feed a cross-slot antenna to achieve dual polarization. Because all the input and output circuits are waveguides, the network is especially useful for high power systems and millimeter wave applications. The crossover circuit exhibits a very low insertion loss and good isolation.

Chang, K.↗
NASA NTRS2010

Compact Magic-T using microstrip-slotline transitions

The design of a compact low-loss Magic-T is described. The planar Magic-T incorporates a compact microstrip-slotline tee junction and small microstrip-slotline transition area to reduce slotline radiation. The Magic-T produces broadband in-phase and out-of-phase power combiner/divider responses, has low in-band insertion loss, and small in-band phase and amplitude imbalance.

U-Yen, Kongpop↗
NASA NTRS1978

Low loss, flexible, lightweight corporate RF feed system for SAR antenna application

Mechanical and electrical efficiency constraints imposed by the SEASAT-A synthetic aperture radar antenna posed difficult design problems. After consideration of available standard cable and waveguide systems, it was determined that an optimum design could be obtained from a suspended substrate RF feed system. Size and mechanical flexibility constraints forced the design of a flexible, suspended substrate section capable of 180-degree flexure. Original design goal for insertion loss over power division was 1 db; measured results indicated 0.6 db maximum across the band. Multipactor testing of system components indicated system breakdown capability in excess of 4 kW compared to a specification input maximum of 1500 W.

Schiavone, F.↗
NASA NTRS2009

The Fiber Optic Subsystem Components on Express Logistics Carrier for International Space Station

ISS SSP 50184 HRDL optical fiber communication subsystem, has system level requirements that were changed to accommodate large loss optical fiber links previously installed. SSQ22680 design is difficult to implement, no metal shell over socket/pin combination to protect the weak part of the pin. Additions to ISS are planned for the future. AVIM still used for interconnection in space flight applications without incident. Thermal cycling resulted in less than 0.25 dB max change in Insertion Loss for all types during cycling, nominal as compared to the AVIM. Vibration testing results conclusion; no significant changes, nominal as compared to AVIM.

Ott, Melanie N.↗
NASA NTRS1989

A low-loss linear analog phase modulator for 8415 MHz transponder application

A breadboard single-section low-loss analog phase modulator with good thermal stability for a spacecraft transponder application has been analyzed, fabricated, and evaluated. A linear phase shift of 70 degrees with a linearity tolerance of plus or minus 7 percent was measured for this modulator from 8257 to 8634 MHz over the temperature range -20 C to 75 C. The measured insertion loss and the static delay variation with temperature were within 2 plus or minus 0.3 dB and 0.16 ps/C, respectively. Four sections will be cascaded to provide the X-band (8415 MHz) phase modulator. The generic modulator design can also be utilized at 7950 to 8075 MHz followed by X4 multiplication to provide modulation of a Ka-band downlink signal.

Mysoor, N.↗
NASA NTRS2007

A Compact Low-loss Magic-T using Microstrip-Slotline Transitions

The design of a compact low-loss magic-T is proposed. The planar magic-T incorporates the compact microstrip-slotline tee junction and small microstrip-slotline transition area to reduce slotline radiation. The experimental results show that the magic-T produces broadband in-phase and out-of-phase power combiner/divider responses, has an average in-band insertion loss of 0.3 dB and small in-band phase and amplitude imbalance of less than plus or minus 1.6 deg. and plus or minus 0.3 dB, respectively.

U-yen, Kongpop↗
DOE OSTI2022

Piezo-optomechanical cantilever modulators for VLSI visible photonics

Visible-wavelength very large-scale integration photonic circuits have a potential to play important roles in quantum information and sensing technologies. The realization of scalable, high-speed, and low-loss photonic mesh circuits depends on reliable and well-engineered visible photonic components. Here, we report a low-voltage optical phase shifter based on piezo-actuated mechanical cantilevers, fabricated on a CMOS compatible, 200 mm wafer-based visible photonics platform. We show linear phase and amplitude modulation with 6 V π cm in differential operation, −1.5 to −2 dB insertion loss, and up to 40 dB contrast in the 700–780 nm range. By adjusting selected cantilever parameters, we demonstrate a low-displacement and a high-displacement device, both exhibiting a nearly flat frequency response from DC to a peak mechanical resonance at 23 and 6.8 MHz respectively, which, through resonant enhancement of Q ∼ 40, further decreases the operating voltage down to 0.15 V π cm.

Dong, Mark↗