Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impact resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Impact Resistance of Uncoated SiC/SiC Composites

Two-dimensional woven SiC/SiC composites fabricated by melt infiltration method were impact tested at room temperature and at 1316 C in air using 1.59-mm diameter steel-ball projectiles at velocities ranging from 115 to 400 m/s. The extent of substrate damage with increasing projectile velocity was imaged and analyzed using optical and scanning electron microscopy, and non-destructive evaluation (NDE) methods such as pulsed thermography, and computed tomography. The impacted specimens were tensile tested at room temperature to determine their residual mechanical properties. Results indicate that at 115 m/s projectile velocity, the composite showed no noticeable surface or internal damage and retained its as-fabricated mechanical properties. As the projectile velocity increased above this value, the internal damage increased and mechanical properties degraded: At velocities >300 m/s, the projectile penetrated through the composite, but the composite retained approx.50% of the ultimate tensile strength of the as-fabricated composite and exhibited non-brittle failure. Predominant internal damages are delamination of fiber plies, fiber fracture and matrix shearing.

Bhatt, Ramakrishna T.↗
DOE OSTI2024

Low-velocity impact resistance and failure characteristics of all thermoplastic woven polymer-fiber-reinforced plastic composites

This study addresses the impact performances of recyclable composites made of all thermoplastic polymer-fiber-reinforced plastics (PFRPs), where the reinforcing fibers and matrix are made of thermoplastic polymers. Three woven PFRPs systems were evaluated, including polypropylene fibers, polypropylene matrix, and high-density polyethylene matrix. In low-velocity impact scenario with an impactor speed of less than 6 m/s, our results demonstrate the energy absorption capabilities of the flat laminate PFRPs compared to woven carbon fiber-reinforced plastics (CFRPs) and aluminum alloy 5052. For the systems studied, the PFRPs can reach the specific energy absorption 89% to 115% of the CFRPs. Even compared with the aluminum alloy 5052, the PFRPs can reach up to 97%. We investigate the failure morphologies of the PFRPs using X-ray µCT scans. They reveal the PFRPs’ unique ductile failure morphologies compared to common CFRPs. In addition, we heal the perforated region in the PFRPs by applying the manufacturing process identical to the initial curing process. The healed panels are perforated again, and they recovered 30% to 38% of their original specific energy absorption, a recovery not achievable with CFRPs. This study provides valuable experimental results, and concrete insights into the potential applications of recyclable PFRPs in various engineering fields. It emphasizes their excellent energy-absorbing capability and repairability.

CFRPs↗
NASA NTRS1971

Heat sterilizable impact resistant cell development

Developments in the design and fabrication of 25 AH, 5AH, 70 AH, and 25 AH high impact cells and batteries are reported along with the development of high cycle life, low impact cells. Discussions of the performance and failure modes are included.

Jordan, A. W.↗
NASA NTRS1973

Impact resistance of current design composite fan blades tested under short-haul operating conditions

Boron/epoxy and graphite/epoxy composite blades were impacted in a rotating whirligig facility with conditions closely simulating those which might be experienced by a STOL engine impacted with various foreign objects. The tip speed of the rotating blades was 800 feet per second. The blades were impacted with simulated birds, real birds, ice balls, and gravel. The results of composite blade impact tests were compared with a titanium blade tested under similar conditions. Neither composite material indicated a clear superiority over the other. Blades made from both composite materials showed more damage than the titanium blades.

Steinhagen, C. A.↗
NASA NTRSDate not supplied

Digitally-Engineered Impact Resistant Aerogel Composites for MMOD Protection (DIRAC-MP)

This project implemented a digital-engineering approach to optimize the impact absorption performance of polymer aerogels and aerogel-based composites for Micrometeoroids and Orbital Debris (MMOD) containment. We developed a curated materials database and a machine-learning framework to derive composition-response relationships, enabling predictive design and targeted material selection. In support of experimental validation, a split Hopkinson pressure bar (SHPB) test rig, specifically adapted for low-density aerogel materials, was designed and built in-house. This project accelerates the development of new aerogel formulations, producing candidate materials tailored for enhanced impact-absorption behavior.

Sadeq Malakooti↗
NASA NTRS1992

Shear failure and impact resistance in graphite fiber laminates

The multispan beam (MSB) test was evaluated as a predictor of damage resistance and damage tolerance in quasi-isotropic graphite laminates. Materials studied were five commercial prepreg system using high-strain and intermediate-modulus carbon fibers, as well as an amorphous thermoplastic system. Failure loads and displacements in the MSB tests showed little rate dependence. Values of compressive strength after a standard low-velocity impact correlated fairly well with the MSB results.

Srinivasan, Krishna↗
NASA NTRS1982

Impact resistance of fiber composites

Stress-strain curves are obtained for a variety of glass fiber and carbon fiber reinforced plastics in dynamic tension, over the stress-strain range of 0.00087-2070/sec. The test method is of the one-bar block-to-bar type, using a rotating disk or a pendulum as the loading apparatus and yielding accurate stress-strain curves up to the breaking strain. In the case of glass fiber reinforced plastic, the tensile strength, strain to peak impact stress, total strain and total absorbed energy all increase significantly as the strain rate increases. By contrast, carbon fiber reinforced plastics show lower rates of increase with strain rate. It is recommended that hybrid composites incorporating the high strength and rigidity of carbon fiber reinforced plastic with the high impact absorption of glass fiber reinforced plastics be developed for use in structures subjected to impact loading.

Chamis, C. C.↗
DOE OSTI2021

Excellent ballistic impact resistance of Al 0.3 CoCrFeNi multi-principal element alloy with unique bimodal microstructure

Multi-principal element alloys represent a new paradigm in structural alloy design with superior mechanical properties and promising ballistic performance. Here, the mechanical response of Al 0.3 CoCrFeNi alloy, with unique bimodal microstructure, was evaluated at quasistatic, dynamic, and ballistic strain rates. The microstructure after quasistatic deformation was dominated by highly deformed grains. High density of deformation bands was observed at dynamic strain rates but there was no indication of adiabatic shear bands, cracks, or twinning. The ballistic response was evaluated by impacting a 12 mm thick plate with 6.35 mm WC projectiles at velocities ranging from 1066 to 1465 m/s. The deformed microstructure after ballistic impact was dominated by adiabatic shear bands, shear band induced cracks, microbands, and dynamic recrystallization. The superior ballistic response of this alloy compared with similar Al x CoCrFeNi alloys was attributed to its bimodal microstructure, nano-scale L1 2 precipitation, and grain boundary B2 precipitates. Deformation mechanisms at quasistatic and dynamic strain rates were primarily characterized by extensive dislocation slip and low density of stacking faults. Deformation mechanisms at ballistic strain rates were characterized by grain rotation, disordering of the L1 2 phase, and high density of stacking faults.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Determining and analyzing the strength and impact resistance of high modulus glass

A number of new glass compositions have been prepared with increased emphasis on compositions without beryllia. Glass preparations have been much more broadly based and have included the eutectic glass fields, and the mullite-rare earth glass systems. Of the new glasses, the best non-toxic composition is UARL 472 with a bulk modulus of only 18.20 million psi. A second experimental glass, UARL 417, was chosen for research in making large quantities of fiber in monofilament form. Tests of these UARL 417 epoxy resin samples in comparison to similar composites made with the DuPont organic fiber, PRD-49-1, show that the UARL composites have a compressive strength 41/2 times higher and a specific compressive strength at least 21/2 times greater. Much of the research effort attempted to answer the question of why a given glass should have an impact strength superior to other glasses. No definitive answer to the question was found.

Bacon, J. F.↗
NASA NTRS1971

Determining and analyzing the strength and impact resistance of high modulus glass

An error was noticed recently in the computer program used to reduce the laboratory sonic measurements to tabulated values of Young's modulus of the bulk samples of experimental glasses. Correction of this error gave revised values for the last fifty experimental glasses prepared in this laboratory. This corrected data, when examined as input material for the calculation of Young's modulus of bulk glasses from composition by the C. J. Phillips procedure, resulted in new values for the contribution per mol of several oxides. The new value for the zinc oxide molal factor is especially significant since it is slightly greater than the factor for beryllia for the types of glasses melted in the UARL research program. This discovery provides a new tool in the search for nontoxic, i.e. without beryllia, high modulus glass fibers particularly when coupled with recent measurements that showed zinc oxide contributes significantly to increased impact strength. New glass compositions prepared in this period and the latest impact strength values measured are also included.

Bacon, J. F.↗
NASA NTRS2020

Durability Characterization of Low Ice Adhesion and Impact Resistance Coatings

Glaze, rime and mixed icing conditions can cause significant variation in aerodynamic performance, fuel efficiency, and flight safety. For commercial aircraft, active icing mitigation strategies are utilized to enable safe flight within icing conditions according to the FAR Part 25/29 Appendix C icing envelope. For general aviation and unmanned aerial vehicles that cannot support active anti-icing technologies, avoidance is the only recourse. Passive approaches have been investigated to reduce weight and energy consumption for active systems and to expand the operational envelope for smaller aircraft. Coatings are one passive method to reduce or mitigate ice accretion on frontal surfaces of commercial aircraft with the greatest region of interest being wing leading edges. Aircraft wing leading edges represent an extreme environment. Durability must be considered for any material to be applied as a coating in this area. Currently, there are no specifications regarding coating durability of a low ice adhesion material applied on the wing leading edge. Therefore, a reasonable starting point is to use the durability specifications put forth for an aircraft external coating. Besides the tests called out in these specifications, others were included such as Taber abrasion to simulate wear and erosion. Beyond durability, performance metrics with regards to adhesion strength of accreted in-flight (i.e., impact) icing are central to determine coating usefulness. Determination of this property though is particularly challenging and only a few facilities have the capability to quantify this. An instrument at NASA Langley Research Center [Adverse Environment Rotary Test Stand Jr., (AERTS Jr.)], based on the AERTS system at The Pennsylvania State University, allows for screening numerous coatings subjected to the icing environment. To establish a benchmark for comparison with research coatings, a state-of-the-art (SOA) commercial aircraft coating was subjected to an array of salient durability and performance experiments. The same tests were conducted using a baseline epoxy (BE) resin formulation that demonstrated some initial promising results for comparison. Results from this initial screening will be discussed herein.

Miranda L Beaudry↗