Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrostaticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Improved Compaction Experiments and Modeling of Waste Isolation Pilot Plant Standard, Non-degraded, Waste Containers

A credible simulation of disposal room porosity at the Waste Isolation Pilot Plant (WIPP) requires a tenable compaction model for the 55-gallon waste containers within the room. A review of the legacy waste material model, however, revealed several out-of-date and untested assumptions that could affect the model’s compaction behavior. For example, the legacy model predicted non-physical tensile out-of-plane stresses under plane strain compression. (Plane strain compression is similar to waste compaction in the middle of a long drift.) Consequently, a suite of new compaction experiments were performed on containers filled with surrogate, non-degraded, waste. The new experiments involved uniaxial, triaxial, and hydrostatic compaction tests on quarter-scale and full-scale containers. Special effort was made to measure the volume strain during uniaxial and triaxial tests, so that the lateral strain could be inferred from the axial and volume strain. These experimental measurements were then used to calibrate a pressure dependent, viscoplastic, constitutive model for the homogenized compaction behavior of the waste containers. This new waste material model’s predictions agreed far better with the experimental measurements than the legacy model’s predictions, especially under triaxial and hydrostatic conditions. Under plane strain compression, the new model predicted reasonable compressive out-of-plane stresses, instead of tensile stresses. Moreover, the new model’s plane strain behavior was substantially weaker for the same strain, yet substantially stronger for the same porosity, than the legacy model’s behavior. Although room for improvement exists, the new model appears ready for prudent engineering use.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Sizing and Selection of Pressure Relief Valves for High-Pressure Thermal–Hydraulic Systems

This study covers the critical concerns related to the sizing, selection, installation, maintenance, and testing of pressure safety valves (PSVs). The aim is to ensure the safety of pressurized systems, hydrostatic transmission systems, and hydraulic plants, including process plants, thermal power plants, and nuclear reactor systems. PSVs are devices that ensure the safety and reliability of pressurized vessels, lines, and systems during overpressure events. The task of selecting which PSV features are of greatest value for a specific purpose is complex—especially in the design of a high-pressure experimental thermal–hydraulic facility for hydrostatic and transient testing of the reactor system—when the systems are in the design and development phases and require qualification and demonstration to prove that they have reached a given level of technological readiness. The present study highlights the required steps for users to follow the associated rules, guidelines, and recommendations. As a part of this research, case studies are presented to help readers better understand the applicable strategy and standards. A discussion and a review of PSV performance degradation and failure are summarized to provide a better understanding of varied process applications and conditions, including fluid flow dynamics, boundary-layer formation and pressure drops, gas bubble formation and collapse, geometric configurations, inlet/outlet piping, abrupt pressure fluctuations, and acoustic resonance. Moreover, this study discusses the servicing and testing of PSVs in a multiphase pressurized system. Overall, it provides a basic overview of how PSVs ensure the safety of pressurized systems, supported by case studies and industrial practices.

02 PETROLEUM↗
DOE OSTI2021

The effect of aspect ratio on the mechanical behavior of Li metal in solid-state cells

The Li metal anode is necessary for solid-state batteries to dramatically exceed the energy density of state-of-the-art conventional Li-ion batteries. To enable the Li metal anode, the mechanical properties of Li metal under compression in a commercially relevant cell configuration must be determined. This work examines the compression creep behavior of Li metal coupled with a relevant model solid-state electrolyte (Li 6.5 La 3 Ta 0.5 Zr 1.5 O 12 ) and current collector (Ni) as a function of applied stress (1–10 MPa) and Li foil thickness (100–700 μm). At 1 MPa applied stress, the strain rate of all Li foil thicknesses under compression was almost four orders of magnitude lower than what is predicted from tensile creep tests. Steady-state creep behavior was observed for Li foil ≥350 μm at 5 MPa and ≥250 μm at 10 MPa. Conversely, sustained creep deformation was not observed for 100 and 150 μm Li foils at any applied stress. It is suggested that friction at the Li/LLZO and Li/Ni interfaces leads to the formation of hydrostatic stress that controls Li deformation at low aspect ratios. Finally, these results have implications for battery pack stack pressure requirements, particularly relating to void formation during stripping and Li metal filament penetration during plating.

25 ENERGY STORAGE↗
DOE OSTI2023

Pressure-Dependent Magnetic Properties of Quasi-2D Cr 2 Si 2 Te 6 and Mn 3 Si 2 Te 6

Recently, pressure has been used to induce structural and magnetic phase transitions in many layered quantum materials whose layers are linked by van der Waals forces. Materials with such weakly held layers allow for relatively easy manipulation of the superexchange mechanism, which can give rise to novel magnetic behavior. Here, using hydrostatic pressure as a disorderless means to manipulate the interlayer coupling, we applied pressure on two quasi-2D sister compounds, namely, Cr 2 Si 2 Te 6 (CST) and Mn 3 Si 2 Te 6 (MST), up to ~1 GPa. Magnetic property measurements with the application of pressure revealed that the ferromagnetic transition temperature decreases in CST, while the opposite occurs for the ferrimagnetic MST. In MST, magnetization decreases with the increase in pressure, and such a trend is not clearly observed within the pressure range studied for CST. The overall pressure effect on magnetic characteristics such as exchange couplings and magnetic anisotropy energies is also examined theoretically using density functional theory. Exchange coupling in MST is strongly frustrated, and the first nearest neighbor interaction is the most dominant of the components with the strongest pressure dependence. In CST, the exchange coupling parameters exhibit very little dependence on pressure. This combined experimental and theoretical work has the potential to expand to other relevant quantum materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Planar, longitudinal, compressive waves in solids: Thermodynamics and uniaxial strain restrictions

A new tri-axial pressure-based constitutive expression has been found using Cauchy's stress tensor. This stress state emphasizes pressure and shear stress. The description is a pressure plus an effective shear stress allowing for a constitutive law based on atomic solid-state phase changes in crystalline cells due to pressure plus shear-based dislocation motion commonly associated with plasticity. Pressure has a new role in the material's constitutive response as it is separated from plasticity. The thermo-mechanical system describes third-order Gibbs’ expressions without specific volume restrictions placed upon the material. Isothermally, the ratio of heat to shear work in elastic copper is shown to approach zero at a very low temperature and become larger than one as temperature approaches melting. Wave compression models investigated are elastic and plastic: in fully elastic materials, the planar wave is restricted by Poisson's effect although plastic shear changes this constraint. Plastic deformation, dominated by dissipative shear stresses in uniaxial strain, heats the material while excluding phase changes from hydrostatic pressures. The material properties per se across Hugoniot shocks are described with entropy concepts. Shock waves are exceedingly complex since the constitutive laws are linked at extreme temperatures, pressures, and shear stresses. Isothermal, isentropic, isochoric, and iso-shear conditions are used throughout with Jacobian algebra.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Nanolamellar phase transition in an additively manufactured eutectic high-entropy alloy under high pressures

Much is unknown about how phase transitions link to micro-/nano-structures in high-entropy systems, especially under extreme pressure and temperature conditions. This work studies the evolution of dual-phase nanolamellar eutectic high-entropy alloy phases of AlCoCrFeNi 2.1 generated by laser powder-bed fusion (L-PBF) for pressures up to 42 GPa. We compare quasi-hydrostatic high pressure synchrotron x-ray diffraction studies on L-PBF printed cylindrical samples up to 5.5 GPa (large-volume Paris–Edinburgh cell) to those carried out on an L-PBF printed foil in a diamond anvil cell where the pressure reached 42 GPa. Our results show that the initially alternating face-centered cubic (FCC) and body-centered cubic (BCC) nanolamellar structure of AlCoCrFeNi 2.1 transformed into single-phase FCC nanolamellae under high pressure with BCC–FCC phase transformation completion at 21 ± 3 GPa. Our results indicate a diffusionless BCC–FCC transformation in this additively manufactured far-from-equilibrium microstructure and demonstrate that the FCC phase is stable up to very high pressures. The measured equation of state for the FCC phase of AlCoCrFeNi 2.1 is presented up to 42 GPa and shows excellent agreement between the data obtained in large-volume press and diamond anvil cell experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simultaneous compression of NaCl, Au, and ruby: toward mutually consistent pressure scales

Here, we evaluate pressure consistency of equations of state (EOS) for NaCl and Au at 300 K. The simultaneous measurements of unit-cell volumes (V) with ruby R1 line shifts (Δλ) in a helium (He) loaded diamond cell effectively remove potential systematic errors. Compression and decompression data were automatically collected at 1 sec interval, yielding a dense dataset with >8,000 (V, Δλ) pairs each for NaCl and Au. Solidification of He has noticeable effects on both V and Delta lambda (hence P). Only data up to similar to 14 GPa, or 6000 (V, P) pairs, can be considered hydrostatic within the resolution. The P-V data are fitted to the Rydberg-Vinet and the 3 rd order Birch-Murnaghan EOS. Predicted pressures of these EOSs agree with those given by the Ruby2020 ruby scale to within +/- 0.05 GPa. Overall, pressures predicted by the Rydberg-Vinet EOS are in better agreement with the average of commonly used NaCl and Au pressure scales.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Model, data, and code for paper "Modeling of streamflow in a 30-kilometer-long reach spanning 5 years using OpenFOAM 5.x"

The data package includes data, model, and code that support the analyses and conclusions in the paper titled “modeling of streamflow in a 30-kilometer-long reach spanning 5 years using OpenFOAM 5.x”. The primary goal of this paper is to demonstrate that key streamflow properties such as water depth, flow velocity, and dynamic pressure in a natural river at 30-kilometer scale over 5 years can be reliably and efficiently modeled using the computational framework presented in this paper. To support the paper, various data types from remote sensing, field observations, and computational models are used. Specific details are described as follows. Firstly, the river bathymetry data was obtained from a Light Detection and Ranging (LiDAR) survey. This data is then converted to a triangulated surface format, STL, for mesh generation in OpenFOAM. The STL data can be found in Model_Setups/BaseCase_2013To2015/constant/triSurface. The OpenFOAM mesh generated using this STL file can be found in constant/polyMesh. Other model setups, boundary and initial conditions can be found in /system and /0.org under folder BaseCase_2013To2015. A similar data structure can also be found in BaseCase_2018To2019 for the simulations during 2018 and 2019. Secondly, the OpenFOAM simulations need the upstream discharge and water depth information at the upstream boundary to drive the model. These data are generated from a one-dimensional hydraulic model and the data can be found under the folder Model_Setups /1D model Mass1 data. The mass1_65.csv and mass1_191.csv files include the results of the 1D model at the model inlet and outlet, respectively. The Matlab source code Mass1ToOFBC20182019.m is used to convert these data into OpenFOAM boundary condition setups.With the above OpenFOAM model, it can generate data for water surface elevation, flow velocity, and dynamic pressure. In this paper, the water surface elevation was measured at 7 locations during different periods between 2011 and 2019. The exact survey locations (see Fig1_SurveyLocations.txt) can be found in folder Fig_1. The variation of water stage over time at the 7 locations can be found in folder /Observation_WSE. The data type include .txt, .csv, .xlsx, and .mat. The .mat data can be loaded by Matlab.We also measured the flow velocities at 12 cross-sections along the river. At each cross-section, we recorded the x, y locations, depth, three velocity components u,v,w. These data are saved to a Matlab format which can be found under folder /Observation_Velocity and /Fig_1. The relative locations of velocity survey locations to the river bathymetry can be found in Figure 1c.The water stage data at the 7 locations from OpenFOAM, 1D, and 2D hydraulic models are also provided to evaluate the long-term performance of 3D models vs 1D/2D models. The water stage data for the 7 locations from OpenFOAM have been saved to .mat format and can be found in /OpenFOAM_WSE. The water stage data from the 1D model are saved in .csv format and can be found in /Mass1_WSE. The water stage from the 2D model is saved as .mat format and can be found in / Mass2_WSEIn addition, the OpenFOAM model outputs the information of hydrostatic and hydrodynamic pressure. They are saved as .mat format under folder /Fig_11/2013_1. As the files are too large, we only uploaded the data for January 2013. The area of different ratio of dynamic pressure to static pressure for all simulation range, i.e., 2013-2015, are saved to .mat format. They can be found in /Fig_11/PA. Further, the data of wall clock time versus the solution time of the OpenFOAM modeling are also saved to .mat format under folder /Fig_13/LogsMat. In summary, the data package contains seven data types, including .txt, .csv, .xlsx, .dat, .stl, .m, and .mat. The former 4 types can be directly open using a text editor or Microsoft Office. The .mat format needs to be read by Matlab. The Matlab source code .m files need to be run with Matlab. The OpenFOAM setups can be visualized in ParaView. The .stl file can be opened in ParaView or Blender. The data in subfolders Fig_1 to Fig_10 and Fig_12 are copied from the aforementioned data folders to generate specific figures for the paper. A readME.txt file is included in each subfolder to further describe how the data in each folder are generated and used to support the paper.Please use the data package's DOI to cite the data package. Please contact yunxiang.chen@pnnl.gov if you need more data related to the paper.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Efficient, Compact, and Smooth Variable Propulsion Motor (Final Report)

In this project, a new architecture of highly efficient hydraulic motor was developed for the propulsion of off-highway vehicles. The motor uses an adjustable linkage driving a cam to vary the displacement of the piston, resulting in a Variable Displacement Linkage Motor (VDLM). The motor uses low friction rolling element bearings to significantly reduce mechanical friction, especially in the demanding low-speed high-torque conditions experienced by off-highway vehicles. The VDLM has high torque capabilities for its size due to the radial piston packaging and use of a multi-lobe cam. A VDLM is very smooth due to the ability to tune the torque ripple through the design of the cam profile. The project was divided into three periods. During the first period, a dynamic model was constructed of the motor to predict the performance of the motor and the vehicle. During the second period, a single-cylinder learning prototype was designed, built, and tested to validate the models constructed in the first period. In the third period, a multi-cylinder prototype motor was optimized, designed, fabricated, and tested. The motor demonstrated excellent mechanical efficiency (above 92.5% across the range of displacements), but the experimentally measure volumetric efficiency was lower than expected due to higher leakage rates created by the poor tolerance control on the prototype. To validate the dynamic models developed in the first period and better understand design trade-offs. In the third period a multi-cylinder concept demonstration prototype will be designed, fabricated, and tested. The final prototype will be tested on a motor dynamometer and will be utilized in hardware-in-the-loop testing to demonstrate its efficiency and performance impacts on the overall drive train. The experimental results were used in a drive train simulation of a compact track loader operating through a drive cycle. Using the VDLM in a hydrostatic circuit yielded 17.1% reduction in fuel consumption and 36.5% reduction in a series hybrid transmission.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Stimuli‐Responsive Emission from Hybrid Metal Halides

Abstract Stimuli‐responsive photoluminescent (PL) materials have attracted considerable attention in recent years owing to their potential applications in anti‐counterfeiting, information encryption, and sensing. Further investigations of the transformation mechanism and potential applications of stimulus‐responsive PL materials are considerably important. In the current study, an organic–inorganic metal halide, C 9 H 15 N 3 SbCl 5 ([C 9 H 13 N 3 ] 2+ is a 1‐(2‐pyridyl) piperazine cation) is obtained, which exhibits a 0D structure withP‐1 space group. At room temperature, when excited by UV light, the C 9 H 15 N 3 SbCl 5 single crystals exhibit unimodal blue light emission at 405 nm, and grinding or hydrostatic pressure induces double‐peak emissions at 405 and 650 nm. Interestingly, double‐emission samples can be restored to single‐emission samples by short annealing or storage in air for 2 weeks, and this process is reversible. Luminescence response to mechanical stimuli can also be achieved in the presence of hydrochloric acid and water. Spectral analysis and the analysis of the microstructural changes revealed that the structural modifications of the inorganic group play a pivotal role in the response to the stimulus. Finally, a composite film device based on C 9 H 15 N 3 SbCl 5 is prepared to demonstrate the potential of these smart materials in anti‐counterfeiting and sensing applications.

Chemistry↗
DOE OSTI2026

Reducing the Strain Required for Ambient‐Pressure Superconductivity in Ruddlesden‐Popper Bilayer Nickelates

ABSTRACT The discovery of high‐temperature superconductivity in pressurized bulk Ruddlesden‐Popper (RP) bilayer nickelates has prompted the conjecture that epitaxial compressive strain might mimic essential aspects of hydrostatic pressure. The realization of superconductivity in films on SrLaAlO 4 (001) (SLAO) supports this correspondence, yet it remains unclear whether the pressure–temperature phase diagram of RP bilayer nickelates can be systematically mapped (and studied at ambient pressure) as a function of epitaxial strain. To this end, experimental access near the elusive edge of the superconducting phase boundary would provide invaluable insight into the nature of the superconducting state and the ground state from which it emerges. Here we report superconducting RP bilayer nickelates grown on LaAlO 3 (001) (LAO), where the compressive strain required for ambient‐pressure superconductivity is nearly halved to −1.2%. These films exhibit a superconducting onset above 10 K and reach zero resistance at 3 K, with normal‐state transport properties differing from those of films grown on SLAO. Our comparative study shows that strain–rather than interfacial structure is the primary factor governing the superconductivity and normal‐state properties. This work offers a new opportunity to probe emergent phenomena near the superconducting phase boundary in the strain–temperature phase diagram of RP bilayer nickelates.

Tarn, Yaoju [Department of Applied Physics Stanfor↗
DOE OSTI2022

Processing and properties of hafnium-doped tin-modified lead zirconate titanate 95/5 ceramics

Niobium (Nb)-doped lead-tin-zirconate-titanate (PSZT) ceramics near the lead-zirconate-titanate 95/5 orthorhombic AFE-rhombohedral FE morphotropic phase boundary (PSZT 13.5/81/5.5 -1.6Nb) were prepared with up to 10 mol.% of hafnium (Hf) substituted for zirconium. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1150°C for 6 h in sealed alumina crucibles with self-same material as the lead vapor source. All compositions were ~98% dense with no detectable secondary phases by X-ray diffraction. The grain size was ~3 μm for all compositions, consisting of equiaxed grains with intergranular porosity. The compositions exhibited remnant polarization values of ~32 μC/cm 2 . Depolarization by the hydrostatic pressure-induced FE-AFE phase transition occurred at 310 MPa for all compositions, resulting in a total depolarization output of 32.4 μC/cm 2 for the PSZT ceramics. Evaluation of the R3c-R3m and R3m-Pm $\bar{3}$ m phase transition temperatures by impedance spectroscopy showed temperatures on heating ranging from 86 to 92°C and 186 to 182°C, respectively, for increasing nominal Hf content. Thermal hysteresis of the phase transitions was also observed in the ceramics, with the transition temperature on cooling being 1–4°C lower. The study demonstrated that the PSZT ceramics are relatively insensitive to variations in Hf content in the range of 0 to 10 mol.%.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Processing and properties of PSZT 95/5 ceramics with varying Ti and Nb substitution

Niobium doped lead-tin-zirconate-titanate ceramics near the PZT 95/5 orthorhombic AFE – rhombohedral FE morphotropic phase boundary Pb 1-0.5y (Zr 0.865-x Ti x Sn 0.135 ) 1-y Nb y O 3 were prepared according to a 2 2+1 factorial design with x = 0.05, 0.07 and y = 0.0155, 0.0195. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1250°C for 6 hours. All compositions were ~98% dense with no detectable secondary phases by XRD. The ceramics exhibited equiaxed grains with intergranular porosity and grain size was ~5 μm, decreasing with niobium substitution. Compositions exhibited remnant polarization values of ~32 μC/cm 2 , increasing with Ti substitution. Depolarization by the hydrostatic pressure induced FE-AFE phase transition was drastically affected by variation of the Ti and Nb substitution, increasing at a rate of 113 MPa / 1% Ti and 21 MPa / 1% Nb. Total depolarization output was insensitive to the change in Ti and Nb substitution, ~32.8 μC/cm 2 for the PSZT ceramics. The R3c-R3m and R3m-Pm3m phase transition temperatures on heating ranged from 90 to 105°C and 183 to 191°C, respectively. Ti substitution stabilized the R3c and R3m phases to higher temperatures, while Nb substitution stabilized the Pm3m phase to lower temperatures. Thermal hysteresis of the phase transitions was also observed in the ceramics, with transition temperature on cooling being as much as 10°C lower.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pressure–Modulated Luminescence Enhancement and Quenching in a Hydrogen–Bonded Organic Framework

Light emission in the solid state is central for illumination, sensing, and imaging applications. Unlike luminescence in dilute solutions, where the excited states are unimolecular in nature, intermolecular interaction plays a significant role in the quantum yield of solid-state luminophores, manifested as competing aggregation-caused quenching (ACQ) and aggregation-induced enhancement (AIE). Both effects are extensively studied in various systems; however, it remains unclear how their competition depends on molecular conformation and intermolecular stacking. Here the direct observation of pressure-modulated AIE-ACQ competition in a crystalline hydrogen-bonded organic framework (HOF) is reported. Using in situ spectroscopies and computational modeling, the intramolecular vibration and intermolecular π–π stacking directly responsible for the non-radiative decay of the excited state are identified. The extent of these two contributions is modulated by hydrostatic pressure and guest molecules in the HOF pores. Furthermore, this work demonstrates a physically neat model system to understand and control solid-state luminescence, and a potential material platform for piezoluminescent sensing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Control of deviatoric stress in the diamond anvil cell through thermal expansion mismatch stress in thin films

Elastic and plastic properties of materials and phase transitions at extreme conditions vary with both hydrostatic pressure and deviatoric stress. To generate and measure controlled deviatoric stress at pressures beyond those accessible with large volume differential and rotational presses and optical access for spectroscopy, experiments tested the combination of diamond anvil cell and thin film technology. Thin films of polycrystalline Cr-doped Al 2 O 3 ruby were prepared using pulsed laser deposition on single-crystal substrates of either Al 2 O 3 sapphire or yttria-stabilized cubic zirconia for contrasting initial film stress, and loaded in diamond anvil cells for confining stress. The piezospectroscopic response of the ruby films demonstrates consistently higher deviatoric stress in the film on zirconia relative to the film on the control sapphire, and an increase in deviatoric stress with applied load. Complementary synchrotron X-ray diffraction of the zirconia substrate confirmed that no pressure-induced phase transitions impacted the stress state of the ruby film, but differences in compressibility of film and substrate result in changes in film stress analogous to thermal expansion mismatch. Furthermore, this technique may be applied to evaluate elastic and plastic response of thin films of a variety of materials under extreme stress.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-pressure Cr 3+ R-line luminescence of zoisite and kyanite: a probe of octahedral site distortion

Here, the Cr 3+ luminescence spectra of zoisite and kyanite, two geologically important minerals, were studied up to 40 and 20 GPa, respectively, in various pressure media. Cr 3+ substitutes into the octahedral aluminum sites in both minerals and the R-line luminescence is a particularly sensitive site-specific probe of the octahedral Al site. Unlike many previous studies where Cr 3+ luminescence was utilized, both these minerals have multiple highly distorted octahedral sites resulting in very large splitting of their R-lines, ~ 300 cm -1 in zoisite and ~ 360 cm -1 in kyanite (for reference, ruby is 29 cm -1 ). For zoisite, the R-line splitting increases as pressure increases and more than triples from its ambient value by 40 GPa, while the R-line splitting in kyanite from the M1 and M2 sites does not change when compressed in a Ne pressure medium up to 20 GPa. We do not observe evidence of any phase transitions in either zoisite or kyanite across the pressure range of these new luminescence measurements. Furthermore, we present some high-pressure luminescence results where kyanite was known to be bridged between the diamond anvils and show how these spectra illustrate the different effect of uniaxial relative to hydrostatic stress on luminescence spectra.

36 MATERIALS SCIENCE↗
DOE OSTI2022

CO 2 supplementation eliminates sugar-rich media requirement for plant propagation using a simple inexpensive temporary immersion photobioreactor

In vitro plant propagation systems such as temporary immersion bioreactors (TIBs) are valuable tools that enable production of disease-free plants with improved traits. However, TIB systems can be expensive, difficult to implement, and prone to contamination due to sugar rich propagation media. Using rapidly growing chicory root cultures to expedite design-build-test cycles, we report here an improved, low-cost version of a previously reported Hydrostatically-driven TIB (Hy-TIB) that facilitates economical use of gas mixtures. Bioreactor improvements include decreased material costs, expanded modes of operation, and a horizontal orientation of a plastic film plant growth chambers that increase propagule light exposure. To take advantage of these improvements, we describe here experiments that evaluate the impacts of elevated CO 2 on propagation of cacao (Theobroma cacao) secondary embryos and nodal cultures of yam (Dioscorea spp.) during both phototrophic and photomixotrophic growth. Our experiments show that elevated CO 2 during plant propagation significantly improved both cacao and yam propagule development and eliminated the need for supplemental sugars in tissue culture growth media. Thus, our improved Hy-TIB shows potential as a simple, low-cost, and scalable propagation platform with cost-effective gas composition control and reduced risk of contamination overgrowth. We provide detailed instructions for assembly of this Hy-TIB design and discuss the implications of its adoption in food-insecure regions of the world.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Predicting Fluid Flow Regime, Permeability, and Diffusivity in Mudrocks from Multiscale Pore Characterisation

In geoenergy applications, mudrocks prevent fluids to leak from temporary (H 2 , CH 4 ) or permanent (CO 2 , radioactive waste) storage/disposal sites and serve as a source and reservoir for unconventional oil and gas. Understanding transport properties integrated with dominant fluid flow mechanisms in mudrocks is essential to better predict the performance of mudrocks within these applications. In this study, small-angle neutron scattering (SANS) experiments were conducted on 71 samples from 13 different sets of mudrocks across the globe to capture the pore structure of nearly the full pore size spectrum (2 nm–5 μm). We develop fractal models to predict transport properties (permeability and diffusivity) based on the SANS-derived pore size distributions. The results indicate that transport phenomena in mudrocks are intrinsically pore size-dependent. Depending on hydrostatic pore pressures, transition flow develops in micropores, slip flow in meso- and macropores, and continuum flow in larger macropores. Fluid flow regimes progress towards larger pore sizes during reservoir depletion or smaller pore sizes during fluid storage, so when pressure is decreased or increased, respectively. Capturing the heterogeneity of mudrocks by considering fractal dimension and tortuosity fractal dimension for defined pore size ranges, fractal models integrate apparent permeability with slip flow, Darcy permeability with continuum flow, and gas diffusivity with diffusion flow in the matrix. This new model of pore size-dependent transport and integrated transport properties using fractal models yields a systematic approach that can also inform multiscale multi-physics models to better understand fluid flow and transport phenomena in mudrocks on the reservoir and basin scale.

36 MATERIALS SCIENCE↗