Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hot pressing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Enabling High-Performance NASICON-Based Solid-State Lithium Metal Batteries Towards Practical Conditions

Solid-state lithium metal batteries (SSLMBs) are promising next-generation high-energy rechargeable batteries. However, the practical energy densities of the reported SSLMBs have been significantly overstated due to the use of thick solid-state electrolytes, thick lithium (Li) anodes, and thin cathodes. Here, a high-performance NASICON-based SSLMB using a thin (60 µm) Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte, ultrathin (36 µm) Li metal, and high-loading (8 mg cm -2 ) LiFePO 4 (LFP) cathode is reported. The thin and dense LAGP electrolyte prepared by hot-pressing exhibits a high Li ionic conductivity of 1 × 10 -3 S cm -1 at 80 °C. The assembled SSLMB can thus deliver an increased areal capacity of ≈1 mAh cm -2 at C/5 with a high capacity retention of ≈96% after 50 cycles under 80 °C. Furthermore, it is revealed by synchrotron X-ray absorption spectroscopy and in situ high-energy X-ray diffraction that the side reactions between LAGP electrolyte and LFP cathode are significantly suppressed, while rational surface protection is required for Ni-rich layered cathodes. This study provides valuable insights and guidelines for the development of high-energy SSLMBs towards practical conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

PLA Renewable Bio Polymer Based Solid-State Gamma Radiation Detector-Dosimeter for Biomedical and Nuclear Industry Applications

Polylactic acid (PLA) as a “green,” renewable corn-soy based polymer resin was assessed as a novel solid-state detector for rapid-turnaround gamma radiation dosimetry in the 1–100 kGy range–of significant interest in biomedical and general nuclear industry applications. Co-60 was used as the source of gamma photons. It was found that PLA resin responds well in terms of rheology and porosity metrics with an absorbed gamma dose (Dg). In this work, rheological changes were ascertained via measuring the differential mass loss ratio (MLR) of irradiated PLA placed within PTFE-framed (40 mm × 20 mm × 0.77 mm) cavities bearing ~0.9 g of PLA resin and pressed for 12–16 min in a controlled force hot press under ~6.6 kN loading and platens heated to 227 °C for the low Dg range: 0–11 kGy; and to 193 °C for the extended Dg range: 11–120 kGy. MLR varied quadratically from 0.05 to ~0.2 (1σ ~ 0.007) in the 0–11 kGy experiments, and from 0.05 to ~0.5 (1σ ~0.01) in the 0–120 kGy experiments. Rheological changes from gamma irradiation were modeled and simultaneously correlated with void-pocket formations, which increase with Dg. A single PLA resin bead (~0.04 g) was compressed 5 min at 216 °C in 0–16 kGy experiments, and compressed 2 min at 232 °C in the 16–110 kGy experiments, to form sturdy ~100 µm thick wafers in the same press. Aggregate coupon porosity was then readily measurable with conventional optical microscope imaging and analyzed with standard image processing; this provided complementary data to MLR. Average porosity vs. dose varied quadratically from ~0 to ~15% in the 0–16 kGy range and from ~0 to ~18% over the 16–114 kGy range. These results provide evidence for utilizing “green”/renewable (under $0.01) PLA resin beads for rapid and accurate (+/-5–10%) gamma dosimetry over a wide 0–120 kGy range, using simple to deploy mass and void measuring techniques using common laboratory equipment.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2025

A New Family of Ternary Intermetallic Compounds with Dualistic Atomic Ordering – The ZIP Phases

A new family of nanostructured ternary intermetallic compounds − named the ZIP phases − is introduced in this work. The ZIP phases exhibit dualistic atomic ordering, i.e., they form two structural variants: one with the fcc diamond cubic structure (space group Fd$\bar{3}$m) and one with the hexagonal structure (space group P6 3 /mmc). They are also characterized by metallic behavior, ionic bonding, and atomic zigzagging. Powder metallurgical routes involving pressure-assisted densification are adopted to demonstrate ZIP phase synthesis in the Nb-Si-Ni, Nb-Si-Co, Ta-Si-Ni, V-Si-Ni, and Nb-Si-Fe ternary systems. Crucially, reactive hot pressing is capable of producing high-purity ZIP phase materials after the judicious, elemental system-specific optimization of the processing route. Synthesis of phase-pure materials – demonstrated in the Nb-Si-Ni ternary system by the synthesis of quasi phase-pure Nb 3 SiNi 2 and Ni 3 SiNb 2 ZIP phase-based materials – is a steppingstone to the prospective exploitation of the ZIP phases. Characterization of Nb 3 SiNi 2 and Ni 3 SiNb 2 involves crystal structure determination, spatially resolved chemical analysis, and determination of select thermal, electrical, magnetic, mechanical, and physical properties. Density functional theory is used to assess the stability of Nb 3 SiNi 2 & Ni 3 SiNb 2 and derivative binary compounds at different temperatures, also exploring the exfoliation of these two ZIP phases along specific surfaces to produce 2D derivatives.

Intermetallic compounds (IMCs)↗
DOE OSTI2021

Bulk nanocrystalline Al alloys with hierarchical reinforcement structures via grain boundary segregation and complexion formation

Grain size engineering, particularly reducing grain size into the nanocrystalline regime, offers a promising pathway to further improve the strength-to-weight ratio of Al alloys. Unfortunately, the fabrication of nanocrystalline metals often requires non-equilibrium processing routes, which typically limit the specimen size and require large energy budgets. In this study, multiple dopant elements in ternary Al alloys are deliberately selected to enable segregation to the grain boundary region and promote the formation of amorphous complexions. Three different fully dense bulk nanocrystalline Al alloys (Al-Mg-Y, Al-Fe-Y, and Al-Ni-Y) with small grain sizes were successfully fabricated using a simple powder metallurgy approach, with full densification connected directly to the onset of amorphous complexion formation. All the compositions demonstrate densities above 99% with grain sizes <60 nm following consolidation via hot pressing at 585 °C. The very fine grain structure results in excellent mechanical properties, as evidenced by nanoindentation hardness values in the range of 2.2-2.8 GPa. Detailed microstructural characterization verifies the segregation of all dopant species to grain boundaries as well as the formation of amorphous complexions, which suggests their influential role in aiding effective consolidation and endowing thermal stability in the alloys. Moreover, nanorods with a core-shell structure are also observed at the grain boundaries, which likely contribute to the stabilization of the grain structure while also strengthening the materials. Lastly, intermetallic particles with sizes of hundreds of nanometers form in all systems. As a whole, the results presented here demonstrate a general alloy design strategy of segregation and boundary evolution pathway that enables the fabrication of multiple nanocrystalline Al alloys with hierarchical microstructures and improved performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Combining direct ink writing with reactive melt infiltration to create architectured thermoelectric legs

Here, we present a new additive-reactive synthesis method where inks – cast into molds or 3D-additively extruded into architectured shapes – are reacted into intermetallic thermoelectric compounds. The new method, as demonstrated for equiatomic TiNiSn, combines: (i) extrusion printing (or casting) of inks containing Ni and Ti powders, (ii) debinding and reactive sintering to form a porous NiTi network, (iii) network infiltration with liquid Sn and subsequent reaction to synthesize the TiNiSn phase. Thin plates, created through this method, show high phase purity and low residual porosity. A thermoelectric figure of merit zT = 0.47 ± 0.05 is achieved at 800 K, within the broad range of values (zT= 0.3–1.0) reported for TiNiSn created via traditional powder hot-pressing methods. Layered TiNiSn microlattices – after 3D ink-extrusion printing and infiltration – exhibit high relative densities and minimal undesirable secondary phase content, with a Seebeck coefficient on par with the ink-cast TiNiSn plates, demonstrating that thermoelectric legs with far-ranging architectural freedom can be created additively with this novel reactive manufacturing method. Numerous other thermoelectric (and other) compounds, currently limited to basic geometries due to brittleness, are amenable to this new method based on a sequence of reactive sintering/infiltration of cast or ink-extruded precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Zirconium-diboride silicon-carbide composites: A review

Zirconium diboride (ZrB 2 ) and silicon carbide (SiC) composites have long been of interest since it was observed that ZrB 2 improved the thermal shock resistance of SiC. However, processing of these materials can be difficult due to high and different sintering temperatures and differences in the thermodynamic stability of each material. ZrB 2 –SiC composites have been processed in a variety of ways including hot-pressing, spark-plasma sintering, reactive melt infiltration, pack cementation, chemical vapor deposition, chemical vapor infiltration, stereolithography, direct ink writing, selective laser sintering, electron beam melting, and binder jet additive manufacturing. Each manufacturing method has its own pros and cons. This review serves to summarize more than 60 years of research and provide a coherent resource for the variety of methods and advancements in development of ZrB 2 –SiC composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis of nanograined zirconium diboride microsphere powder feedstock via emulsification of suspensions

Ceramic nanograined materials have desirable characteristics compared to their macroparticle counterparts but are rarely used in industrial applications due to issues with poor handleability and health hazards. Due to interparticle forces that become more dominant as the particle size decreases, it is difficult to use nanomaterials to fill dies, spread on surfaces, or flow through hoppers found in various manufacturing processes. In this work, we report a scalable gelcasting solution and unique emulsification process to create microspheres composed of nanoscale powders to enhance the flowability and handleability of nanomaterials. The gelcasting solution and emulsification process can be used with any nanoparticle composition that can be suspended in a liquid phase. This paper reports the effects of various parameters on zirconium diboride microsphere formation, such as surfactant content and mixing conditions. The microspheres maintain the nano-scale characteristics of the powder but improve its flowability by using cross-linked polyvinyl alcohol to combine irregularly shaped zirconium diboride nanoparticles with a particle diameter of 60 nm into larger spherical particles with a d 50 ~25 μm. This hierarchical feedstock engineering design combine the positive characteristics of materials across both length scales and improve the flowability of the feedstock from a Hausner Ratio of 1.56 to 1.19. The materials produced using this technique can be used in thermal plasma spray, die filling for hot pressing or spark plasma sintering, and binder jet printing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Corrosion of Al 2 O 3 /Cr and Ti 2 O 3 /Cr composites in flowing air and CO 2 at 750°C

Hot-pressed Al 2 O 3 /Cr and Ti 2 O 3 /Cr composites were exposed to synthetic air or CO 2 at 750 °C. The Al 2 O 3 /Cr composites formed external Cr 2 O 3 scales, and exhibited slow parabolic oxidation kinetics, in both gases. The Cr 2 O 3 scales formed in CO 2 possessed finer grains, and thickened at a faster rate, than Cr 2 O 3 scales formed in air. The Ti 2 O 3 /Cr composites formed thick external TiO 2 scales with internal oxidation zones that also contained Cr 2 O 3 scales on subsurface Cr grains. After 20 h at 750 °C, the Ti 2 O 3 /Cr composites exhibited parabolic oxidation kinetics in both gases, although the oxidation rates were significantly higher than for the Al 2 O 3 /Cr composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characterization of fusion welded ceramics in the SiC-ZrB 2 -ZrC system

Various SiC-ZrB 2 -ZrC ceramics were joined by fusion welding to determine the maximum silicon carbide content that could be joined. Commercial powders were hot pressed, machined, and preheated to 1450 °C before joining with a tungsten inert gas welding torch at 160–200 A. Resulting welds were cross-sectioned and analyzed to determine which compositions were weldable and to characterize microstructural evolution in welded samples. As compositions approached the ternary eutectic, the welds had smaller SiC grains and exhibited better weldability. Penetration depth of welds was controlled by a combination of current input and welding speed. Here, the ternary eutectic in the system was found at 36.9 ± 1.3 vol% SiC, 42.7 ± 1.5 vol% ZrB 2 , and 20.4 ± 1.9 vol% ZrC and its melting temperature was 2330 ± 23 °C. A ternary phase diagram for the SiC-ZrB 2 -ZrC was constructed and proposed via microstructural analysis of arc melted pellets on binary joins between each binary eutectic and the ternary eutectic in the system.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Review of additive manufacturing and densification techniques for the net- and near net-shaping of geometrically complex silicon nitride components

Silicon nitride (Si 3 N 4 ) is an advantageous material due its unique combination of mechanical, thermal, chemical, and electrical properties both at ambient and elevated temperatures. Because of these properties there are a wide range of applications for Si 3 N 4 components. Applications include heat exchangers, environmental barrier coatings, osteointegration scaffolds, radomes, and integrated circuitry. Furthermore, such applications often require geometric complexity for efficient and/or effective operation. However, traditional ceramics processing methods such as hot-pressing or die extrusion are typically limited to simple axis-symmetric shapes. With the advent of additive manufacturing, there has been significant advancement into the forming of geometrically complex Si 3 N 4 components. This review documents additive manufacturing advancements that have demonstrated, or are capable of, fabricating Si 3 N 4 components with complex geometry.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical properties of fusion welded ceramics in the $\mathrm{SiC-ZrB}$ 2 and $\mathrm{SiC-ZrB}$ 2 -$\mathrm{ZrC}$ systems

Mechanical properties of welded SiC-ZrB 2 and SiC-ZrB 2 -ZrC ceramics were measured up to 1700 °C. Commercial powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics using either tungsten inert gas welding or plasma arc welding. Toughness of the parent materials was 3–4 MPa*m 1/2 which decreased after welding to 2–2.5 MPa*m 1/2 . Strength of the SiC-ZrB 2 -ZrC parent material was ~700 MPa at 25 °C, ~300 MPa at 1700 °C, and retained 40–60% of this strength once welded. Strength of the SiC-ZrB2 parent material was ~600 MPa at 25 °C and 1700 °C and retained 20–30% of this strength once welded. Griffith analysis indicated that the strength in the parent materials was controlled by the size of SiC clusters while strength of welds was controlled by the size of pores in fusion zones. Therefore, removal of pores in produced fusion zones should be investigated to improve strength of future ceramic welds.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fusion welding of refractory metals and ZrB 2 -SiC-ZrC ceramics

Molybdenum and a molybdenum alloy were fusion welded to ZrB2-based ceramics to determine if the electrical and thermal properties of the metals and ceramics affected their weldability. Commercial ceramic powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics to commercial metals using plasma arc welding. Weldability varied as indicated by the range of porosity observed within the fusion zones. Measured thermal and electrical properties appeared to have little to no effect on the weldability of metal-ceramic welds despite the large range of values measured across each property. Differences in melting temperatures between metal and ceramic coupons did affect weldability by changing the weld penetration depth into ceramic coupons. Finally, future studies on metal-ceramic welds are suggested to investigate the effect that work function, melt viscosity, wetting, or other properties have on weldability.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ion irradiation study of lithium silicates for fusion blanket applications

Here, this study reports on the microstructural and compositional evolutions, deuterium release and lithium loss behavior in lithium silicates. Pellets of biphasic Li 4 SiO 4 and Li 2 SiO 3 were fabricated using hot pressing of powders. Sequential irradiation with Si + , He + and D + ions was performed up to 773 K to emulate one-year 6 Li burnup in 6 Li 4 SiO 4 inside the SlimCS DEMO. Crystalline Li 4 SiO 4 phase was not observed in the irradiated depth region of all the samples in this study. In spite of full amorphization in the near-surface region, Li 2 SiO 3 irradiated to a high dose at 773 K remained crystalline in the damage peak region, suggesting that Li 2 SiO 3 is more irradiation resistant to amorphization than Li 4 SiO 4 . Radiolysis may be primarily responsible for silicate decomposition and amorphization. Data from this study also show that D release from the pellet is very efficient during ion irradiation at 773 K, which is accompanied with a significant Li loss. Thermal annealing for 10 min at 773 K for the room-temperature irradiated pellet leads to a nearly complete D release without an observable Li loss. A concept of Ni coating on tritium breeder materials is discussed with supporting data to minimize Li loss without a significant impact on tritium diffusion and release.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Determination of Ce 3+ , Co 2+ , Mn 2+ and Fe 2+ diffusion coefficients in Nafion® membrane

Concentration gradient diffusion coefficients for Ce 3+ , Co 2+ , Mn 2+ and Fe 2+ cations are determined in Nafion®211 membranes over a wide range of environmental conditions. Measurements are made using finite-width cation-rich bands introduced to NR211 via a hot-pressing procedure. A robust method of accurate diffusion coefficient determination of the finite-width deposits is developed using a Fick's second law of diffusion solution for one-dimensional systems. The transition metal dications are found to have nearly identical NR211 diffusion coefficients under water saturated conditions over the 22–80 °C range. The powerful chemical mitigant, Ce 3+ , is about one-half as diffusive as the dications under identical conditions. Derived diffusion coefficients for Ce 3+ and Co 2+ are found to be independent of initial cation concentration over the range of 12.5–70 mol% exchange level. The diffusion behavior of Ce 3+ in 80 °C liquid water and saturated water vapor is identical. The diffusion coefficients of Ce 3+ are shown to have a strong dependence on membrane hydration level varying by a factor of more than 30 over the range of 95 to 40% RH. Finally, the implications of these new diffusion findings are applied to a discussion of potential guidelines for the development of highly durable fuel cell systems, which employ mobile metal cations as lifetime-extending redox stabilizers.

08 HYDROGEN↗
DOE OSTI2025

Amorphous complexion-aided sintering enables scalable processing of bulk nanocrystalline Cu-Zr with high strength and compressive plasticity

Nanocrystalline alloys can have exceptional strengths, yet due to limited microstructural stability it is difficult to fabricate bulk pieces through traditional processing routes that retain nanosized grains. In this study, centimeter-sized Cu-Zr alloy pellets were fabricated via a simple and improved powder metallurgy processing route. Different consolidation temperatures and times were employed to investigate the effect of amorphous grain boundary complexions on densification and the resulting mechanical properties. Bulk compression tests were carried out, with the samples that were hot pressed at 900 °C for 10 h exhibiting an excellent combination of average yield strength of 722 ± 45 MPa and average failure strain of 25.3 ± 2.4 %. Furthermore, we find that a powder processing route which enables amorphous complexion-assisted sintering leads to samples that (1) reach full density without requiring quenching treatments or other complex processing, (2) demonstrate appreciable plasticity, and (3) have strength that competes with commercially available high-strength Cu alloys.

Bulk nanocrystalline alloy↗
DOE OSTI2020

New red phosphor ceramic K 2 SiF 6 :Mn 4+

We report a new transparent ceramic phosphor for use in LED lighting has been fabricated. The previously reported and optimized narrow-emitting red phosphor, K 2 SiF 6 :Mn 4+ (KSF), has been consolidated into a transparent ceramic phosphor for the first time, accomplished via hot-pressing the feedstock phosphor powder in a die under vacuum. KSF ceramics were fabricated with varying doping concentrations of Mn 4+ and their properties studied. The absorption and emission spectra of the ceramics were identical to the feedstock phosphor powders and are ideal for LED lighting with strong absorption at 450 nm and narrow emission around 630 nm. The absorbance of the ceramics was directly proportional to the doping concentration. The ceramics were excited at various blue light fluxes and their emission intensities measured to study the effect of Mn 4+ concentration on intensity-driven “droop” in the emission output. The ceramics with a lower Mn 4+ doping were more efficient under higher light fluxes due to a decrease in Auger upconversion losses. KSF ceramics can allow a much longer path length of the diode light through the phosphor, as compared to phosphor-in-silicone, enabling the use of low optical absorption and the associated reduced activator concentration. The ceramics are measured to have a thermal conductivity of ~1.0 W/m-K, higher than that of phosphor-in-silicone or phosphor-in-glass. Several of these properties make KSF ceramics potentially desirable for use in white light LEDs. Greater thermal conductivity helps with heat dissipation, the lower surface area of the ceramic compared to the powder minimizes the environmental vulnerability of KSF, and the ability to lower the Mn 4+ concentration reduces Auger recombination losses and mitigates the temperature rise, particularly at higher light flux.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Packing fraction control during additive manufacturing of powder green bodies

The demand for high performance ceramic and metal components with complex geometry necessitates developments in powder handling and green body shaping. Here, in this study, vibrational powder deposition is adapted to three-dimensional printing with the ability to modulate packing fraction during printing. Boron carbide powder with sub-micron primary particle size is printed over a packing fraction range of 25.0 % to 46.5 % (below the poured density to above the tapped density). Solid metal powders are printed at 67.5 %, which enables novel freestanding, vertical-walled features without binder. These capabilities introduce opportunities for more complex geometries in high-performance materials, e.g. large-scale uniaxial hot-pressing of ceramic ballistic armor components with graded thickness and three-dimensional curved or stepped features (by compensating for displacement differences during compaction). This technology also enables multi-material patterning of additive manufacturing powder beds with reduced feedstock quantity requirements and wastage.

36 MATERIALS SCIENCE↗