Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “glass fiber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Comparing Parallel Plastic‐to‐X Pathways and Their Role in a Circular Economy for PET Bottles

Abstract The United States generates the most plastic waste of any country and is a top contributor to global plastic pollution. Multiple end‐of‐life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different lifetimes and utilities. Herein, they present a material flow model equipped with consequential life cycle assessment, cost analysis, and a plastic circularity indicator that considers product quality and lifetime. The model is used to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) bottle mechanical downcycling to lower‐quality resin, closed‐loop glycolysis to food‐grade PET, upcycling to glass fiber‐reinforced plastic, and conversion to non‐plastic products (electricity, oil) on a United States economy‐wide basis for the year 2020. A brute force algorithm suggests that a combination of 68% glycolysis, 11% mechanical recycling, 6% upcycling, 9% landfilling, and 5% incineration can minimize the cost and GHG emissions and maximize the circularity of the current PET economy. However, uncertainty around transportation distances, materials recovery facility efficiencies, and recycling yields can result in different “optimal” pathway mixes. This flexible framework enables informed decision‐making to move toward a cost‐ and environment‐conscious circular economy for plastic.

09 BIOMASS FUELS↗
DOE OSTI2020

Real-time damage characterization for GFRCs using high-speed synchrotron X-ray phase contrast imaging

Here, we report the application of high-speed synchrotron X-ray phase contrast imaging (PCI) in real-time damage characterization for glass fiber reinforced composites (GFRCs) subjected to dynamic loading. Dynamic single-edge notched bending (DSENB) experiments on pre-notched S-2 GFRCs were performed on a modified Kolsky compression bar. During loading, the synchrotron X-ray beam penetrated through the composite specimen from the side to detect damage evolution inside the material. Entire dynamic events were recorded by a high-speed camera as image sequences.0° and 90° unidirectional and cross-ply composites were investigated. An optical imaging technique was also employed to capture similar dynamic events in comparison with the radiographic imaging. It is demonstrated that high-speed X-ray PCI had sufficient phase contrast to characterize a crack initiation at a 20-μm spatial resolution within 920 ns and track the crack geometry during propagation, thereby providing reliable data to quantify the dynamic damage resistance of GFRCs. Furthermore, being capable of recognizing microscopic damage-related features at a sub-10-μm resolution, high-speed X-ray PCI provided fundamental material failure mechanisms to reveal the essential of macroscale structural failure of composites. It can also track the damage evolution inside and between individual plies of laminated composites. However, current high-speed X-ray PCI technique only supports in-situ observation and the high timing and spatial resolutions are limited within a field of view of ~2.5 mm in square, preventing its application in the three-dimensional and larger-area damage detection for GFRC structures.

42 ENGINEERING↗
DOE OSTI2023

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Fused deposition modeling (FDM) printed polymers are rarely used as a structural material due to anisotropic and low mechanical properties compared with conventional composites. In recent years, greater need has been expressed for recycling of materials, such as recyclable FDM, at the end of service life to reduce environmental pollution and manufacture cost. However, how the amount of resin uptake in the skin and skin/core interphase affects the bending and shear performance of the sandwich composites when replacing the low strength and ductile core (conventional core) with a high strength and brittle core (FDM printed PLA (polylactic acid) core) still remains unclear. A new manufacturing routine is needed to improve the incorporation of FDM printed polymers in composite structures. In this work, FDM printed PLA was used as core material and sandwiched between two unidirectional glass fiber reinforced polymer (GFRP) skins to form a sandwich composite by compression-molding (CM) process, which provides a good manufacturing strategy for skin/core interphase modification. The significance of the CM process is proved by investigating the effect of resin uptake on bending and in-plane/out-of-plane shear performances. Current first order shear deformation (FSDT) theory lacks a direct connection between the in-plane shear stress and out-of-shear stress in the core region of sandwich composites. With the help of DIC, a connection between the in-plane shear and the out-of-plane shear strain was built and in-plane shear properties can acquire through out-of-plane shear properties, hence reducing the redundancy of sample preparation or the need for simulation. A significant improvement was found compared with the optimized resin uptake (Optimized resin uptake range: 20.43%–22.86 wt%) 3D-printed PLA core sandwich composite and lowest performance sandwich composite (Improvement: in-plane shear strength (~34%)/modulus (~29%), out-of-plane shear strength (~25%)/modulus (~31%), specific peak bending load (~19%)). Finally, compared with balsa core sandwich composites, the 3D-printed cores are suitable for use in composite sandwich structures in many applications with a satisfactory strength-to-weight ratio.

3D-printed core sandwich composite↗
DOE OSTI2021

High-speed synchrotron X-ray phase-contrast imaging for evaluating microscale damage mechanisms and tracking cracking behaviors inside cross-ply GFRCs

In this study, we integrated the high-speed synchrotron X-ray phase-contrast imaging (PCI) with a modified Kolsky compression bar loading platform to visualize the dynamic failure processes of cross-ply glass fiber reinforced composites (GFRCs). Four S-2 glass/SC-15 composite specimens were prepared, having similar thicknesses but different stacking sequences, namely as [0 12 /90 12 ], [90 12 /0 12 ], [0 8 /90 8 /0 8 ], and [90 8 /0 8 /90 8 ]. Three-dimensional synchrotron X-ray computed tomography and scanning electron microscopy (SEM) were employed to examine the microstructures and quantify the fiber volume fractions. Each specimen was notched and subjected to a dynamic three-point flexural loading. The onset of cracking close to the notch tip, crack propagation in 0° or 90° plies and their interface, crack opening, and ultimately failure of the specimen were captured by high-speed synchrotron X-ray PCI. Additional dynamic experiments were performed to determine the average time when the stress wave propagated through the specimen and correlate the X-ray images with the specimen&#x27;s force-deflection response. Finally, the surface morphology of each specimen after the dynamic loading was imaged by SEM. Comparison between real-time X-ray images and post-fracture SEM images demonstrated the capability of the X-ray method to record damage evolution inside composites. Furthermore, the high spatial and temporal resolutions of the X-ray setup and edge enhancement by PCI enabled the identification of microscale damage features within 1 μs. Two damaging processes were identified, crack growth was quantified, and fracture toughness of the composites was evaluated. The method is deemed useful to reveal microscale damage mechanisms and track cracking behaviors inside cross-ply GFRCs under dynamic loading in real time.

42 ENGINEERING↗
DOE OSTI2025

Comparison of interlaminar damage modeling strategies for hybrid composite/aluminum laminates subjected to low-velocity impact

Low-velocity impact of hybrid metal-composite structures was investigated experimentally and computationally. Composite laminates consisting of 2D woven glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) were joined with a 6061-T6 aluminum plate using an epoxy adhesive. Two variations of the structure were studied; one consisting of all plies oriented at 0° and one consisting of all plies oriented at 45°. A drop tower was used to impact structures at a range of energies, including energies above and below the threshold at which the aluminum layer was perforated. Numerical simulations were implemented using Sierra/SM, an in-house transient dynamics finite element code developed at Sandia National Laboratories. A Hosford plasticity model was used to describe the response of the aluminum layer. A newly implemented orthotropic continuum damage mechanics (CDM) constitutive model was used to represent the composite laminate. This 3D-CDM model was compared to a cohesive zone model (2D-CDM/CZM) to investigate efficacy of aluminum perforation energy prediction, delamination prediction, and computational cost. Accuracy of each model was evaluated using the experimental results. Each showed good agreement with the tests for both the force and velocity histories, as well as the observed damage mechanisms. The 2D-CDM/CZM model was marginally more accurate in capturing both the composite and aluminum behavior — this model averaged error percentages of -11.2% and 10.8% for residual velocity and peak force, respectively. Meanwhile, the 3D-CDM model predictions yielded average error percentages of -35.5% (velocity) and 22.6% (force). However, the 3D-CDM model generally resulted in a decreased computational cost; the average run time was 14% shorter than the 2D-CDM/CZM model and 3x as many timesteps per hour were computed using the same computational resources. In conclusion, new experimental data on the impact and perforation resistance of metal-composite laminates is presented in addition to numerical predictions of the impact behavior.

Carbon fiber↗
DOE OSTI2026

Novel application of the modal strain energy technique for state-of-the-art damping predictions

Structural damping, which measures the energy dissipation of a vibrating structure, is a key modeling input for lightweight structures but is notoriously hard to predict. This work utilizes vibration-based measurements of centimeter-scale coupons and the modal strain energy approach to predict structural damping of a lightly damped structure. The approach was originally validated with panels shorter than a meter in length. This work extends the validation to a 2.75 m beam made of unidirectional and biaxial glass fiber laminates bonded by adhesive. The comparison between three-dimensional finite element model predictions and full-scale experimental measurements of damping show an average error of 5.2% for the first five modes. Additionally, the modal strain energy approach is newly applied with a one-dimensional geometrically exact beam theory model and a two-dimensional sectional analysis solver. This beam approach accurately predicts the damping behavior of the first bending modes but loses accuracy for higher order modes that are dominated by three-dimensional effects. This novel approach provides faster simulations while allowing arbitrary beam cross sections. The paper also investigates traditional and high-force dynamic mechanical analysis to measure structural damping of coupons. Both alternatives show significant errors in attempted validation against the theoretical thermoelastic damping of aluminum coupons.

17 WIND ENERGY↗
DOE OSTI2020

Anomalously high elastic modulus of a poly(ethylene oxide)-based composite electrolyte

The practical use of lithium metal anodes in solid-state batteries requires a polymer membrane with high lithium-ion conductivity, thermal/electrochemical stability, and mechanical strength. The primary challenge is to effectively decouple the ionic conductivity and mechanical strength of the polymer electrolytes. We report a remarkably facile single step synthetic strategy based on in-situ crosslinking of poly(ethylene oxide) (xPEO) in the presence of a woven glass fiber (GF). Such a simple method yields composite polymer electrolytes (CPE) of anomalously high elastic modulus up to 2.5 GPa over a broad temperature range (20 °C – 245 °C) that has never been previously documented. An unsupervised machine learning algorithm, K-mean clustering analysis, was implemented on the hyperspectral Raman mapping at the xPEO/GF interface. Using such a unique means, we show for the first time that the promoted mechanical strength originates from xPEO and GF interactions through dynamic hydrogen and ionic bonding. High ionic conductivity is achieved by the addition plasticizer (e.g. tetraglyme), where trifluoromethanesulfonate anions are tethered to the xPEO matrix and Li + cations are favorably transported through coordination with the plasticizer. Further, stringent galvanostatic cycling tests indicates the CPE can be stably cycled for >3000 h in a Li-metal symmetric cell at a moderate temperature (nearly 1500 Coulombs/cm 2 Li equivalents), outperforming most of the PEO-based electrolytes. The GF reinforced CPE reported here has multifunctional uses, such as solid electrolytes for all solid-state batteries and membranes for redox-flow batteries. Although the focus of this study is on lithium-based batteries, the results are equally promising for other alkali metal based batteries such as sodium and potassium.

25 ENERGY STORAGE↗
DOE OSTI2021

Self-re-adhering alkali-activated cement composite and its ability to mitigate corrosion of carbon steel in 300 °C hydrothermal environment

Cement-steel interface is a weak point of cement sheath integrity under the environments of high-temperature geothermal wells. This paper presents carbon steel (CS) adherence behaviors of 300 °C-autoclaved alkali-activated Calcium-Aluminate-Cement (CAC)/fly ash F (FAF) (Thermal Shock Resistant Cement, TSRC), granulated blast furnace slag (GBFS)/SiO 2 , and Ordinary Portland Cement (OPC)/SiO 2 blends. The composites’ ability to preserve the bond under the conditions of thermal shock (TS) and strong acid attack (pH 0.6 H 2 SO 4 /brine at 90 °C) as well as their ability to recover the damaged bond and provide steel corrosion protection after additional short-time 5-day curing at 300 °C were evaluated. GBFS/SiO 2 sheath underwent catastrophic failure in the first TS cycle; OPC/SiO 2 lost 78 % and TSRC 51 % of the bond strength in 6 cycles. Only TSRC-CS bond survived 30 days of strong acid exposure; OPC/SiO 2 bond failed after 18 days and GBFS/SiO 2 after 20 days. Addition of micro-glass fibers (MGF) to TSRC further improved its bond strength and CS corrosion protection. Samples of TSRC-CS cured for 30 days at 300 °C before the bond damage recovered 49 % of the damaged bond strength after additional short-time curing. The CS protected by the re-adhered TSRC showed low corrosion rate of 0.13 mm/year (TSRC-MGF), 0.2 mm/year (TSRC) vs. 0.64 mm/year for OPC/SiO 2 protected CS.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

On the quantification and efficient propagation of imprecise probabilities with copula dependence

This paper addresses the problem of quantification and propagation of uncertainties associated with dependence modeling when data for characterizing probability models are limited. Practically, the system inputs are often assumed to be mutually independent or correlated by a multivariate Gaussian distribution. However, this subjective assumption may introduce bias in the response estimate if the real dependence structure deviates from this assumption. In this work, we overcome this limitation by introducing a flexible copula dependence model to capture complex dependencies. Here, a hierarchical Bayesian multimodel approach is proposed to quantify uncertainty in dependence model-form and model parameters that result from small data sets. This approach begins by identifying, through Bayesian multimodel inference, a set of candidate marginal models and their corresponding model probabilities, and then estimating the uncertainty in the copula-based dependence structure, which is conditional on the marginals and their parameters. The overall uncertainties integrating marginals and copulas are probabilistically represented by an ensemble of multivariate candidate densities. A novel importance sampling reweighting approach is proposed to efficiently propagate the overall uncertainties through a computational model. Through an example studying the influence of constituent properties on the out-of-plane properties of transversely isotropic E-glass fiber composites, we show that the composite property with copula-based dependence model converges to the true estimate as data set size increases, while an independence or arbitrary Gaussian correlation assumption leads to a biased estimate.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Design, performance, and cost savings of using GF-PC additively manufactured tooling for stamping of HSS 590 sheet metal

Conventional sheet metal forming tooling in the automotive industry is made up of hardened steel and used for mass-production. Prototype tooling made of metal is durable, but it is only used for a small number of parts despite its high cost, contributing heavily to the vehicle development cost. Additive Manufacturing (AM) offers a low-cost alternative for fabricating tooling suitable for low-volume production. Here, this study investigates the feasibility of using AM polymer composite tooling for the stamping of 1.5mm thickness HSS 590 steel sheets through a two-pronged approach – experimental and numerical analysis. Sheet metal stamping experiments were conducted with glass fiber reinforced polycarbonate (GF-PC) AM polymer tooling and their performance was evaluated based on various metrics such as tool deformation and part accuracy. Finite element simulations of the stamping process were performed, which accurately captured the tool deformations seen in experiments with the use of anisotropic material models. The effective use of simulations in optimizing process parameters to achieve the desired final part geometry is also demonstrated. The GF-PC AM polymer composite tooling was found to be well suited for low volume production applications with potential cost savings.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A low-cost sulfate-based all iron redox flow battery

Redox flow batteries (RFBs) are promising choices for stationary electric energy storage. Nevertheless, commercialization is impeded by high-cost electrolyte and membrane materials. Here, we report a low-cost all-iron RFB that features inexpensive FeSO 4 electrolytes, microporous membrane along with a glass fiber separator. The addition of 0.1 м 1-ethyl-3-methylimidazolium chloride (EMIC) overcomes the low solubility of FeSO 4 in water which is raised to 2.2 м. DFT calculations demonstrate that EMI + can strengthen the interaction between sulfate anions and water molecules. This electrolyte composition also allows both anode and cathode reactions to operate without actively maintaining a pH gradient between them, thus eliminating the need for expensive ion exchange membranes. The all-iron RFB demonstrates stable operation at a current density of 20 mA cm –2 for more than 800 cycles via a simple, periodic regeneration process. Furthermore, the system cost of FeSO 4 /EMIC RFBs is projected to be $ 50 per kWh due to its low-cost active materials and the inexpensive microporous membrane. Finally, this low-cost, high-concentration all-iron RFB is a promising stationary energy–storage system for storing renewable energy.

25 ENERGY STORAGE↗
DOE OSTI2025

Sustainable, degradable and malleable low-dielectric-constant thermosets derived from biomass for recyclable green electronics

In view of their excellent thermal and chemical resistance, favorable adhesion properties, high tensile strength, and other advantages, epoxy thermosets have numerous industrial applications such as coating, adhesive, and composite material production. However, bisphenol A (BPA)-based resins, which account for a significant fraction of the above thermosets, adversely affect human health by interfering with the normal functioning of the endocrine system and cannot be easily decomposed and recycled. Herein, degradable and sustainable bio-based epoxy thermosets with crosslinked network structures are prepared by the epoxidation of isosorbide with epichlorohydrin and the curing of the produced isosorbide diglycidyl ether (ISDGE) with cyclic lactones through a cationic ring-opening reaction. The ISDGE thermosets fully decompose into soluble and recyclable products under mildly basic conditions within three days, which is ascribed to the presence of ester moieties within the polymer network structure. Compared to a representative BPA-based epoxy, ISDGE-based thermosets exhibit lower dielectric constants and are more flexible. Moreover, the glass fibers in ISDGE-based prepregs can be fully recovered after on-demand degradation. Furthermore, our work provides promising eco-friendly alternatives to conventional epoxy thermosets and paves the way for the reduction of plastic waste generation and the development of recyclable green electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A carbon-efficient bicarbonate electrolyzer

Carbon efficiency is one of the most pressing problems of carbon dioxide electroreduction today. While there have been studies on anion exchange membrane electrolyzers with carbon dioxide (gas) and bipolar membrane electrolyzers with bicarbonate (aqueous) feedstocks, both suffer from low carbon efficiency. In anion exchange membrane electrolyzers, this is due to carbonate anion crossover, whereas in bipolar membrane electrolyzers, the exsolution of carbon dioxide (gas) from the bicarbonate solution is the culprit. Here, we first elucidate the root cause of the low carbon efficiency of liquid bicarbonate electrolyzers with thermodynamic calculations and then achieve carbon-efficient carbon dioxide electroreduction by adopting a near-neutral-pH cation exchange membrane, a glass fiber intermediate layer, and carbon dioxide (gas) partial pressure management. We convert highly concentrated bicarbonate solution to solid formate fuel with a yield (carbon efficiency) of greater than 96%. A device test is demonstrated at 100 mA cm -2 with a full-cell voltage of 3.1 V for over 200 h.

42 ENGINEERING↗
DOE OSTI2020

Imprecise global sensitivity analysis using bayesian multimodel inference and importance sampling

Global Sensitivity Analysis (GSA) aims to understand the relative importance of uncertain input variables to model response. Conventional GSA involves calculating sensitivity (Sobol’) indices for a model with known model parameter distributions. However, model parameters are affected by aleatory and epistemic uncertainty, with the latter often caused by lack of data. In this paper, we propose a new framework to quantify uncertainty in probability model-form and model parameters resulting from small datasets and integrate these uncertainties into Sobol’ index estimates. First, the process establishes, through Bayesian multimodel inference, a set of candidate probability models and their associated probabilities. Imprecise Sobol’ indices are calculated from these probability models using an importance sampling reweighting approach. This results in probabilistic Sobol’ indices, whose distribution characterizes uncertainty in the sensitivity resulting from small dataset size. The imprecise Sobol’ indices thus provide a measure of confidence in the sensitivity estimate and, moreover, can be used to inform data collection efforts targeted to minimize the impact of uncertainties. Through an example studying the parameters of a Timoshenko beam, we show that these probabilistic Sobol’ indices converge to the true/deterministic Sobol’ indices as the dataset size increases and hence, distribution-form uncertainty reduces. The approach is then applied to assess the sensitivity of the out-of-plane properties of an E-glass fiber composite material to its constituent properties. This second example illustrates the approach for an important class of materials with wide-ranging applications when data may be lacking for some input parameters.

42 ENGINEERING↗
DOE OSTI2021

Assessment of MQXF Quench Heater Insulation Strength and Test of Modified Design

The HL-LHC interaction region magnet triplets (Q1,Q2, and Q3) will be composed of superconducting Nb 3 Sn quadrupoles. The MQXF quadrupole protection system is based on CLIQ (Coupling-Loss Induced Quench system) and outer layer quench heaters. Furthermore, this paper reports a summary of quench heaters to coil high voltage tests performed on MQXF short and long coils in air after fabrication, and in air and He gas after magnet training. Breakdown voltage values demonstrate good margin with respect to the Electrical design criteria for the HL-LHC inner triplet mag-nets. A modification in the quench heater installation-with an extra layer of fiber glass between the coil and the quench heater trace-has been proposed and tested in a mirror magnet to further increase electrical margins. Results demonstrated improvements of high voltage margin at the expense of a clear increase of hot spot temperature.The baseline heater to coil insulation was assessed to be able to guarantee safe operation for the Nb 3 Sn quadrupole magnets for the interaction regions of HL-LHC.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Stray-Capacitance As a Simple Tool for Monitoring and Locating Heat Generation Demonstrated in Three Superconducting Magnets

Real-time monitoring of heat loads in cryogenic systems is critical for many applications, particularly high field magnets. In this work, we demonstrated that by monitoring changes in the capacitance of local probes consisting of thin metal strips with a porous glass fiber dielectric, boiling helium from as little as 0.1 J of deposited heat can be located by an analysis of the response speed and amplitude in nearby probes. We further implemented stray-capacitance monitoring of a magnet's metal support structures, a more global probe of the magnet volumes, in three high temperature superconducting Bi-2212 magnet types. Global structural stray-capacitance monitoring was evaluated for a single racetrack coil, a common coil dipole, and a canted cosine theta winding, showing a quench response comparable to voltage signals without inductive effects. The response of the local and global probes was compared in the single racetrack coil with well-known quench properties. Monitoring the cool-down of the common coil dipole demonstrated the added benefit of the global stray-capacitance as a liquid level monitor. This simple method of monitoring the capacitance has proven to be a versatile and robust technique for monitoring and locating heat.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Infrared thermography NDT for in-situ defect detection in sandwich composite panel manufacturing

Composite manufacturing presents numerous challenges, as defects can arise from various sources throughout the process. In sandwich composite structures, the integration of a foam core introduces additional complexity and increases the likelihood of defect formation like delamination. To mitigate these issues and reduce the risk of future structural failures, in-situ monitoring during manufacturing is essential. This study investigates infrared (IR) thermography as a non-destructive technique for detecting manufacturing defects in foam-core sandwich composite panels under thermally excited conditions representative of in-situ processing. A stationary FLIR A8590 IR camera (640 × 512 pixels, 30Hz, 17mm lens, 9 ft stand-off distance) was used to monitor prefabricated panels subjected to controlled external heating simulating compression molding and resin cure exotherm. Interlaminar delamination defects with characteristic sizes ranging from 0.25 × 0.25in² to 5 × 5in² produced measurable surface temperature depressions of approximately 4–10°C during transient cooling, exceeding the effective noise floor of the camera by more than two standard deviations. Thicker laminates exhibited prolonged defect detectability windows due to increased thermal diffusion time. In contrast, embedded Teflon inclusions generated weak thermal contrasts of ≤ 3°C, approaching the measurement noise floor, due to limited thermal property contrast with the surrounding glass fiber composite. These results establish quantitative detectability limits for stationary thermographic inspection of sandwich composite panels under manufacturing-representative thermal cycles.

Barakat, Abdallah [ORNL] (ORCID:0000000296141398)↗