Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fracture characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Alphonsus crater - Floor fracture and dark-mantle deposit distribution from new 3.0-cm radar images

The lunar crater Alphonsus is characterized by numerous fractures or graben, and by endogenic dark-halo craters. Existing maps of fractures from analysis of lunar photography may be biased by the east-west solar illumination. This paper presents new high-resolution, dual-polarization 3.0-cm wavelength radar images of Alphonsus with radar illumination from northerly directions, and uses these data to better map the locations of both the graben and a variety of dark-mantle deposits. The distribution of fractures, and several graben which cut the crater floor and central ridge, are cited as possible evidence for simultaneous, post-Imbrium uplift of both structures. Some of the endogenic dark halo deposits are more extensive in depolarized radar images than in photographs; these extensions are attributed in some cases to more distant emplacement of pyroclastic material, and in others to fortuitous connections with smoother, less cratered portions of the Alphonsus floor.

Zisk, Stanley H.↗
NASA NTRS1985

Effects of strain rate on delamination fracture toughness of graphite/epoxy

The objective of this paper is to evaluate various experimental techniques and analysis methods for the characterization of interlaminar fracture toughness, and to determine the effects of strain rate on that property for a graphite/epoxy composite. Mode I interlaminar fracture was investigated by means of a double-cantilever beam (DCB) specimen for AS-4/3501-6 graphite/epoxy. Hinged tabs were used to insure unrestrained rotation at the free ends. Specimens were loaded at quasi-static deflection rates of up to 8.5 mm/s corresponding to crack extension rates of over 51 mm/s. Crack extension was monitored by means of strain gages mounted on the surface of the specimen, or a conductive-paint circuit attached to the edge of the DCB specimen. Continuous records were obtained of load, deflection, and crack extension for determination of the strain energy release rate. The latter was expressed as a power law of the crack extension velocity. Results indicate that the strain energy release rate increases with crack velocity by up to 28 percent for the range of rates considered.

Daniel, I. M.↗
NASA NTRS1985

Progressive damage, fracture predictions and post mortem correlations for fiber composites

Lewis Research Center is involved in the development of computational mechanics methods for predicting the structural behavior and response of composite structures. In conjunction with the analytical methods development, experimental programs including post failure examination are conducted to study various factors affecting composite fracture such as laminate thickness effects, ply configuration, and notch sensitivity. Results indicate that the analytical capabilities incorporated in the CODSTRAN computer code are effective in predicting the progressive damage and fracture of composite structures. In addition, the results being generated are establishing a data base which will aid in the characterization of composite fracture.

Source record↗
NASA NTRSDate not supplied

Toughening of Boron Carbide Composites by Hierarchical Microstructuring

Due to a unique combination of properties including high hardness, low density, chemical and thermal stability, semi-conductivity, and high neutron absorption, boron carbide (B4C) is a potential candidate for various applications involving extreme environment. However, B4C’s current application is limited because of its low fracture toughness. In this study, a hierarchical microstructure design with features including TiB2 grains and graphite platelets was used to toughen B4C by simultaneously utilizing multiple toughening mechanisms including crack deflection, bridging, and micro-crack toughening. Using field-assisted sintering technology (FAST), B4C composites with dense and hierarchical microstructure were fabricated. Previously, the fracture toughness of fabricated B4C composites was measured at micro-scale using micro-indentation to have up to 56% improvement. In this work, the B4C composites’ fracture toughness was characterized at macro-scale using four-point bending methods and compared with previous results obtained at micro-scale. Micromechanics modeling of fracture behaviors for B4C-TiB2 composites was also performed to evaluate the contributions from experimentally observed toughening mechanisms. From four-point bending tests, B4C composites reinforced with both TiB2 grains (~15 vol%) and graphite platelets (~8.7 vol%) exhibited the highest fracture toughness enhancement from 2.38 to 3.65 MPa∙m^(1/2). The measured values were lower than those obtained using micro-indentation but maintained the general trends. The discrepancy between the indentation and four-point bending test results originated from the complex deformation behaviors triggered by the high contact load during indentation tests. Through micromechanics modeling, introduced thermal residual stress due to thermal expansion mismatch between B4C and TiB2, and weak interphases at B4C-TiB2 boundaries were identified as the main causes for experimentally observed toughness enhancement. These results proved the effectiveness of hierarchical microstructure designs for B4C toughening and can provide reference for the future design of B4C composites with optimized microstructures for further fracture toughness enhancement.

composites↗
NASA NTRS2002

C-Coupon Studies of SiC/SiC Composites: Microstructual Characterization - Part 2

A 'C-coupon' was used to measure the interlaminar tensile behavior of five different composite materials: Sylramic/MI (melt infiltration SiC matrix), ZMl/MI, Sylramic/S300, and ZMI and Hi-Nicalon with an S200 matrix at room temperature, 816 C, and 1204 C. Fracture behavior was characterized by field emission scanning electron microscopy, and observed cracking compared with events measured by modal acoustic emission. Both radial and matrix hoop cracking along the inner radius arising from hoop stresses were observed for all material types. In those composites in which the radial cracks were sufficiently wide to view the composite interior, fracture was observed to occur at the fiber BN or BN matrix interface.

Hurwitz, Frances I.↗
NASA NTRSDate not supplied

Calculating Mode Mixity in Interlaminar Fracture of Composite Laminates

To accurately predict delamination under mixed-mode loading, cohesive elements must partition the energies dissipated in Mode I and Mode II correctly. The ability of cohesive models to predict mode mixity was evaluated by performing analyses of the single leg bending (SLB) test, which exhibits a variable mode mixity with crack length. Accordingly, two numerical integration methods were developed to compute the energy partitioning: (i) a local calculation of the accumulated work of tractions at each point along the crack path, and (ii) a global J-integral “snapshot” calculation along a contour around the process zone. In the case of a composite laminate with properties characterized by short fracture process zone (FPZ), the results of these two methods correlate well with each other and with a linear elastic fracture mechanics solution. However, FPZscan be long due to fiber bridging or due to the intrinsic toughness of the material. Then, the results of mode-mixity calculations obtained with various methods vary widely from each other. It is argued that the global J-integral calculation is the most accurate interpretation of the energy release rate and mode mixity for either short or long process zones. This solution will provide a more accurate characterization of resistance curves and mode mixity in experimental results, and it will also guide the development of more accurate mixed-mode cohesive laws for tougher materials characterized by strong R-curve responses, such as thermo-plastic composites.

cohesive zone analysis↗
NASA NTRS1982

A simple test for the interlaminar fracture toughness of composites

A simple test method for the measurement of delamination resistance is assessed through its application to 11-ply graphite-epoxy laminates whose matrices employ the F185 and 205 resins. The F185 resin has the same base epoxy as the 205, to which liquid and solid elastomers have been added. The critical value of the mixed mode energy release rate, calculated from a closed form equation employing nominal strain measurements from the onset of edge delamination, show that addition of the elastomers to the base epoxy increases interlaminar fracture toughness. Comparison of these results with those of width-tapered double cantilever beam (WTDCB) test data for the two materials shows a similar strain energy release rate, establishing the accuracy of the novel method. Both tests are found to be needed, however, for the quantitative characterization of interlaminar fracture toughness.

Obrien, T. K.↗
NASA NTRS2014

Multilayer Pressure Vessel Materials Testing and Analysis Phase 2

To provide NASA with a suite of materials strength, fracture toughness and crack growth rate test results for use in remaining life calculations for the vessels described above, Southwest Research Institute® (SwRI®) was contracted in two phases to obtain relevant material property data from a representative vessel. An initial characterization of the strength, fracture and fatigue crack growth properties was performed in Phase 1. Based on the results and recommendations of Phase 1, a more extensive material property characterization effort was developed in this Phase 2 effort. This Phase 2 characterization included additional strength, fracture and fatigue crack growth of the multilayer vessel and head materials. In addition, some more limited characterization of the welds and heat affected zones (HAZs) were performed. This report

Popelar, Carl F.↗
NASA NTRS1998

Effect of Measured Welding Residual Stresses on Crack Growth

Welding residual stresses in thin plate A516-70 steel and 2219-T87 aluminum butt weldments were measured by the strain-gage hole drilling and X-ray diffraction methods. The residual stress data were used to construct 3D strain fields which were modeled as thermally induced strains. These 3D strain fields were then analyzed with the WARP31) FEM fracture analysis code in order to predict their effect on fatigue and on fracture. For analyses of fatigue crack advance and subsequent verification testing, fatigue crack growth increments were simulated by successive saw-cuts and incremental loading to generate, as a function of crack length, effects on crack growth of the interaction between residual stresses and load induced stresses. The specimen experimental response was characterized and compared to the WARM linear elastic and elastic-plastic fracture mechanics analysis predictions. To perform the fracture analysis, the plate material's crack tearing resistance was determined by tests of thin plate M(T) specimens. Fracture analyses of these specimen were performed using WARP31D to determine the critical Crack Tip Opening Angle [CTOA] of each material. These critical CTOA values were used to predict crack tearing and fracture in the weldments. To verify the fracture predictions, weldment M(T) specimen were tested in monotonic loading to fracture while characterizing the fracture process.

Hampton, Roy W.↗
NASA NTRS1985

Impact wear of iron rich superalloys

The impact-sliding wear resistance of chill cast and aligned eutectic Fe-base superalloys against M42 and 17-4 PH steel counterface materials is examined. The aligned material tests were run with carbide fibers perpendicular to the counterface contact surface and the characterization focused on fracture processes as observed in the subsurface microstructure of the worn materials. Metallographic analyses were performed on specimens exposed to various numbers of repetitive impact load cycles, and for comparison, two other aligned composites were tested with the same fiber orientation under identical test conditions against hardened M42 tool steel. A strong improvement was found in wear resistance of an aligned eutectic structure as compared to the corresponding randomized chill cast structure. Experiments with the softer 17-4 counterface were characterized by transfer onto the Fe-base superalloy, and the cracks formed were oriented transverse to the relative sliding direction and occurred in a periodic fashion. Observations in subsurface regions of the worn materials indicated crack intergranularity with an occasional transgranular fracture of the M7C3 carbide phase.

Wayne, S. F.↗
NASA NTRS1988

Fatigue behavior of 5Ni-Cr-Mo-V steel weldments containing fabrication discontinuities

The applicability of linear elastic fracture mechanics to characterize the fatigue behavior of high-strength steel weldments containing lack-of-penetration (LOP) and slag/lack-of-fusion (S/LOF) discontinuities is explored. Full penetration, double-V butt welds with reinforcements removed were tested under zero-to-tension axial loading. Various filler metals and welding techniques were used. Both sound welds and welds containing discontinuities were cycled to failure. Where possible, cycles to crack initiation were estimated by strain gage measurements. The fracture mechanics approach was successful in correlating the fatigue lifetimes of specimens containing single LOP discontinuities of varying size. However, the fatigue behavior of specimens containing multiple S/LOF discontinuities proved to be much more complex and difficult to analyze.

Gill, Steven J.↗
NASA NTRS1983

The mechanics of delamination in fiber-reinforced composite materials. Part 2: Delamination behavior and fracture mechanics parameters

Based on theories of laminate anisotropic elasticity and interlaminar fracture, the complete solution structure associated with a composite delamination is determined. Fracture mechanics parameters characterizing the interlaminar crack behavior are defined from asymptotic stress solutions for delaminations with different crack-tip deformation configurations. A numerical method employing singular finite elements is developed to study delaminations in fiber composites with any arbitrary combinations of lamination, material, geometric, and crack variables. The special finite elements include the exact delamination stress singularity in its formulation. The method is shown to be computationally accurate and efficient, and operationally simple. To illustrate the basic nature of composite delamination, solutions are shown for edge-delaminated (0/-0/-0/0) and (+ or - 0/+ or - 0/90/90 deg) graphite-epoxy systems under uniform axial extenstion. Three-dimensional crack-tip stress intensity factors, associated energy release rates, and delamination crack-closure are determined for each individual case. The basic mechanics and mechanisms of composite delamination are studied, and fundamental characteristics unique to recently proposed tests for interlaminar fracture toughness of fiber composite laminates are examined.

Wang, S. S.↗
NASA NTRS1983

The mechanics of delamination in fiber-reinforced composite materials. II - The delamination behavior and fracture mechanics parameters

Based on theories of laminate anisotropic elasticity and interlaminar fracture, the complete solution structure associated with a composite delamination is determined. Fracture mechanics parameters characterizing the interlaminar crack behavior are defined from asymptotic stress solutions for delaminations with different crack-tip deformation configurations. A numerical method employing singular finite elements is developed to study delaminations in fiber composites with any arbitrary combinations of lamination, material, geometric, and crack variables. The special finite elements include the exact delamination stress singularity in its formulation. The method is shown to be computationally accurate and efficient, and operationally simple. To illustrate the basic nature of composite delamination, solutions are shown for edge-delaminated (0/-0/-0/0) and (+ or - 0/+ or - 0/90/90 deg) graphite-epoxy systems under uniform axial extension. Three-dimensional crack-tip stress intensity factors, associated energy release rates, and delamination crack-closure are determined for each individual case. The basic mechanics and mechanisms of composite delamination are studied, and fundamental characteristics unique to recently proposed tests for interlaminar fracture toughness of fiber composite laminates are examined. Previously announced in STAR as N84-13222

Wang, S. S.↗
NASA NTRS1981

Computational methods in nonlinear structural and solid mechanics; Proceedings of the Symposium, Washington, D.C., October 6-8, 1980. Symposium sponsored by the George Washington University and NASA

Topics discussed include computational strategies for nonlinear problems in structural mechanics, time integration techniques and the numerical solution of nonlinear algebraic equations, material characterization and nonlinear fracture mechanics, nonlinear interaction problems, and seismic response and the nonlinear analysis of concrete structures. Also considered are nonlinear problems for nuclear reactors, crash dynamics and impact problems, nonlinear problems of fibrous composites and advanced nonlinear applications, and computerized symbolic manipulation and nonlinear analysis software systems.

Noor, A. K.↗
NASA NTRS1984

Characterizing Delamination Resistance of Toughened Resin Composites

The delamination resistance of toughened resin composites was studied. Both the edge delamination test (EDT) and the double-cantilever-beam (DCB) test provided a useful ranking of improvements in delamination resistance between brittle and tough resin composites. Several layups were designed for the edge delamination test to cover a wide range of mixed-mode conditions. The DCB and the various layups of the EDT were then used to characterize the interlaminar fracture behavior of brittle and toughened resin composites subjected to both static and cyclic loading.

Obrien, T. K.↗
NASA NTRS1992

SAR in support of geological investigations of the Sudbury structure

Imaging radar is an important contributing source of information for a range of geological problems and environments. Airborne SAR and ERS-1 data integrated with other geoscience datasets are being used in an attempt to characterize the crustal fracturing associated with the Sudbury structure. This presentation highlights examples of integrated and composite images aimed at facilitating the interpretation of the Sudbury structure. This work is the result of an ongoing cooperative multidisciplinary SAR study of the basin carried out by the Canada Center for Remote Sensing, Ontario's provincial Remote Sensing Office, the Ontario Geological Survey, and the Geological Survey of Canada.

Singhroy, V.↗
NASA NTRS1993

Constraints on the thermal evolution of Venus inferred from Magellan data

One interpretation of the Magellan data suggests that the cratering record on Venus was erased by a global resurfacing event, or events, the latest ending about 500 m.y. ago. In this global-resurfacing model the resurfacing was followed by minor volcanism and tectonism that has been concentrated primarily in the equatorial highland regions characterized by extensive fracture belts and rifts. A thermal evolution model of Venus that can explain these observations is one in which a deformable lithosphere, capable of being incorporated in mantle circulations, provides an almost stress-free condition at the surface. Mantle convection with an almost stress-free boundary at the surface cools the interior more efficiently. Rapid cooling decreases the Rayleigh number of mantle convection below a transition value required for oscillatory convection, and the vigor of convection diminishes as the mantle changes to a quasi-steady circulation after about 500 m.y. ago.

Arkani-Hamed, J.↗
NASA NTRS2014

Adhesive Characterization and Progressive Damage Analysis of Bonded Composite Joints

The results of an experimental/numerical campaign aimed to develop progressive damage analysis (PDA) tools for predicting the strength of a composite bonded joint under tensile loads are presented. The PDA is based on continuum damage mechanics (CDM) to account for intralaminar damage, and cohesive laws to account for interlaminar and adhesive damage. The adhesive response is characterized using standard fracture specimens and digital image correlation (DIC). The displacement fields measured by DIC are used to calculate the J-integrals, from which the associated cohesive laws of the structural adhesive can be derived. A finite element model of a sandwich conventional splice joint (CSJ) under tensile loads was developed. The simulations indicate that the model is capable of predicting the interactions of damage modes that lead to the failure of the joint.

Girolamo, Donato↗