Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow instability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The effect of inhomogeneities in coal-based mesophase pitch on filament formation and melt spinning for carbon fiber

Mesophase pitch-based carbon fibers excel as high specific strength and modulus materials, but challenges in stable, continuous melt spinning processing are a serious limiting factor. Inhomogeneities in the pitch may result in flow instabilities that can lead to filament breakage. This work aims to characterize and offer mitigation strategies for the negative effects that inhomogeneities such as isotropic binder, gels, and other inclusions impart on melt spinning of mesophase pitch. The effect of inhomogeneities on spinning stability are analyzed using capillary rheometry, borescope imaging of elongating filaments, and filtration. With no filter, immediate blockage of the spinning capillary occurred. Improvement in melt spinning duration was observed when a porous metal filter (20 μm nominal pore size) was utilized, but no significant further improvement in spinning duration was found upon decreasing the filter nominal pores size to 10, 5 and 2 μm. Moreover, flow instabilities that disrupted melt spinning stability were observed by capillary rheometry when the size of included isotropic pitch domains were larger than approximately 10 μm. Resultant carbon fiber properties and SEM imaging of fracture surfaces are reported.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

STAT7 v2.0 User Guide

The STAT7 software was developed to perform steady-state, single-phase thermal hydraulics analysis of plate-fueled reactors based on statistical propagation of uncertainties. Application of the software includes non-power research and test reactor analysis, and it has been used for the conversion to low- enriched uranium fuel of U.S. High Performance Research Reactors such as the Massachusetts Institute of Technology Research Reactor. Since it can be necessary to repeat reactor safety analysis, such as during fuel reloading, STAT7 accommodates flexibility in analyzing many practical aspects of reactor fuel management. STAT7 uses a Monte Carlo approach to model uncertainty in common fuel fabrication parameters and other key reactor operating parameters required for reactor thermal hydraulics analysis. These safety calculations are ultimately intended to protect against high fuel plate temperatures due to critical heat flux, or onset of flow instability. STAT7 supports water properties based on the IAPWS-IF97 functions (The International Association for the Properties of Water and Steam Industrial Formulation 1997 for the Thermodynamic Properties of Water and Steam) in addition to fitted functions. STAT7 predicts axial profiles of fuel, cladding, and coolant temperature along a lateral stripe that runs the full length of the fuel plate from the bottom to the top. STAT7 can simultaneously analyze every axial node in each lateral stripe of all fuel plates and coolant channels in every fuel element of an entire reactor core. Power splits are calculated for each axial node of each plate to determine how much of the power goes out each face of the plate. In a single execution, STAT7 can be used to perform full core analysis by analyzing the margin to onset of nucleate boiling and onset of flow instability for each axial node of each stripe of each plate of each fuel element in the core.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

STAT7 v1.2 User Guide: The STAT7 Code for Statistical Propagation of Uncertainties in Steady-State Thermal Hydraulics Analysis of Plate-Fueled Reactors

The STAT7 software was developed to perform steady-state, single-phase thermal hydraulics analysis of plate-fueled reactors based on statistical propagation of uncertainties. Application of the software is for non-power research and test reactors, including conversion to low-enriched uranium fuel of U.S. High-Performance Research Reactors such as Massachusetts Institute of Technology Research Reactor. Since it can be necessary to repeat analysis during fuel reloading, STAT7 accommodates flexibility in analyzing many realistic aspects of reactor fuel management. STAT7 uses a Monte Carlo approach to model uncertainty in common fuel fabrication parameters and other key reactor operating parameters required for thermal hydraulics analyses of research and test reactors. These safety calculations are ultimately intended to protect against high fuel plate temperatures due to critical heat flux, or onset of flow instability. STAT7 supports water properties based on the IAPWS-IF97 functions (The International Association for the Properties of Water and Steam Industrial Formulation 1997 for the Thermodynamic Properties of Water and Steam) in addition to the fit functions. STAT7 predicts axial profiles of fuel, cladding, and coolant temperature along a lateral stripe that runs the full length of the fuel plate from the bottom to the top. STAT7 can simultaneously analyze all of the axial nodes of all of the fuel plates and all of the coolant channels for one latera stripe of a fuel element. Power splits are calculated for each axial node of each plate to determine how much of the power goes out each face of the plate. By running STAT7 multiple times, full core analysis can be performed by analyzing the margin to onset of nucleate boiling and onset of flow instability for each axial node of each stripe of each plate of each fuel element in the core.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1988

Application of bifurcation theory to axial flow compressor instability

When a compression system goes unstable, the mode of response depends on the operating and system parameters, such as throttle setting and B parameter. Previous numerical work on the model developed by Moore and Greitzer (1986) has provided a limited picture of the parametric effects. Applying bifurcation theory to a single-harmonic version of the model has supplied much more complete information, defining the boundaries of each mode of response in the parameter space. Specifically, this is shown in a plot of B vs. throttle setting, which compares well with the corresponding map produced experimentally. The importance of the shape of the rotating stall characteristic is emphasized. The analysis shows a qualitative difference between classic surge and deep surge.

Mccaughan, F. E.↗
NASA NTRS1993

On the instability of flow in a streamwise corner

The linear stability of an incompressible laminar flow in the blending boundary layer between the boundary layer in a 90 deg streamwise corner and a Blasius boundary layer well away from the corner is examined using a locally parallel flow approximation. It is shown that the influence of the outer boundary conditions associated with oblique modes of disturbances which are anti-symmetric about the bisector plane have a profound effect on the stability of the flow. As a result, in good agreement with observation, the critical streamwise Reynolds number, associated with a spanwise location is significantly reduced as the corner is approached, being R(sub Cr) = 60 approximately for spanwise distance of z* = 6x*R(sup -1) from the corner compared with R(sub Cr) = 322 approximately for z* = 20x*R(sup -1), where x* measures downstream distance from the leading edges. At R = 600, the growth rate of the most amplified mode of disturbance at the former location is over six times greater than that at the latter; the corresponding wave angle at the two locations is respectively 44 deg and 5 deg, approximately.

Dhanak, Manhar R.↗
NASA NTRS2023

Effects of Heating Configuration and Operating Parameters on Heat Transfer and Interfacial Physics of Microgravity Flow Boiling With Subcooled Inlet Conditions –Experiments Onboard the International Space Station

This study is part of the Flow Boiling and Condensation Experiment (FBCE), a collaborative effort between the Purdue University Boiling and Two-Phase Flow Laboratory (PU-BTPFL) and the NASA Glenn Research Center. The FBCE fitted with the Flow Boiling Module (FBM) was launched to the International Space Station (ISS) in August 2021 and experiments were successfully performed from February to July 2022 to amass a large microgravity-flow-boiling database. This study is focused on heat transfer and flow visualization of microgravity flow boiling of n-Perfluorohexane in a rectangular channel of 5.0 mm height, 2.5 mm width (heated), and 114.6 mm length, with subcooled inlet conditions. High-speed-video photography is utilized to present flow patterns and temporal interfacial behavior. Heat transfer results are presented in the form of flow boiling curves and both parametric curves and streamwise profiles of wall temperature and heat transfer coefficient. Firstly, the parametric effects of mass velocity (199.4 – 3200.0 kg/m 2 s), inlet subcooling (0.2 – 46.0°C), and inlet pressure (124.2 – 176.7 kPa), on the aforementioned aspects are assessed for double-sided heating to establish them for a microgravity environment. Of these three parameters, mass velocity and inlet subcooling mostly determine the microgravity flow boiling behavior, while inlet pressure plays an insignificant role. Flow patterns for double-sided heating are more complex than those for single-sided heating due to interaction between the two vapor layers. Vapor interaction is minimized at high subcoolings and high mass velocities due to strong condensation offered by the subcooled bulk liquid layer separating them. Despite the different flow patterns, both single- and double-sided heating generally result in similar parametric trends and local heat transfer coefficients for similar operating conditions. Flow instabilities manifest as temporal flow anomalies and temperature oscillations, and their severity increases with increasing boiling number. Secondly, the effects of heating configuration are analyzed by comparing and contrasting several aspects of single- and double-sided heating data. The heat fluxes at which onset of nucleate boiling degradation (ONBD) and critical heat flux (CHF) occur are distinctly different for single- and double-sided heating. There exists a threshold inlet subcooling demarcating the dominance of flow acceleration and condensation effects in vapor removal from the near-wall region and replenishment of fresh liquid for boiling. Above the threshold, condensation from the near-wall region is dominant and single-sided heating yields higher heat fluxes, and below it, acceleration is dominant and double-sided yields higher heat fluxes. At mass velocity in the range of 200 – 2400 kg/m 2 s, the threshold inlet subcooling lies in the approximate range of 20 – 30°C (corresponding inlet quality of roughly -0.40 – -0.20).

Microgravity↗
NASA NTRS1981

Compressible boundary-layer stability calculations for sweptback wings with suction

The stability of the laminar boundary layers on two transonic wings of infinite span with distributed suction is investigated with the compressible, parallel-flow stability theory. Both wings have supercritical airfoil sections; one has a sweep angle of 23 deg, the other of 35 deg. Zero-frequency disturbances are used to represent cross-flow instability, and disturbances with the wavenumber vector aligned with the local flow direction represent traveling-wave instability. In both cases, the maximum spatial amplification rate is used as a measure of the instability. For the suction, distributions with constant mass flux downstream of the starting point are used. The main objective is to determine how the maximum amplification rate varies with the magnitude and starting point of the suction. It is found for both types of disturbances that the maximum amplification rate varies almost linearly with the suction magnitude up to at least the point where the amplification rate is halved. Different starting locations for the suction in the first 4% of the chord were found to affect cross-flow instability, but to have little influence on traveling-wave instability.

Mack, L. M.↗
DOE OSTI2024

Structure Formation Through Magnetohydrodynamical Instabilities in Primordial Disks

The shear flow instabilities under the presence of magnetic fields in the primordial disk can greatly facilitate the formation of density structures that serve as seeds prior to the onset of the gravitational Jeans instability. We evaluate the effects of the Parker, magnetorotational and kinematic dynamo instabilities by comparing the properties of these instabilities. We calculate the mass spectra of coagulated density structures by the above mechanism in the radial direction for an axisymmetric magnetohydrodynamic (MHD) torus equilibrium and power density profile models. Our local three-dimensional MHD simulation indicates that the coupling of the Parker and magnetorotational instability creates spiral arms and gas blobs in an accretion disk, reinforcing the theory and model. Such a mechanism for the early structure formation may be tested in a laboratory. The recent progress in experiments involving shear flows in rotating tokamak, field reversed configuration (FRC) and laser plasmas may become a key element to advance in nonlinear studies.

Noguchi, Koichi↗
NASA NTRS2010

Development and Application of Plasma Actuators for Active Control of High-Speed and High Reynolds Number Flows

Active flow control is often used to manipulate flow instabilities to achieve a desired goal (e.g. prevent separation, enhance mixing, reduce noise, etc.). Instability frequencies normally scale with flow velocity scale and inversely with flow length scale (U/l). In a laboratory setting for such flow experiments, U is high, but l is low, resulting in high instability frequency. In addition, high momentum and high background noise & turbulence in the flow necessitate high amplitude actuation. Developing a high amplitude and high frequency actuator is a major challenge. Ironically, these requirements ease up in application (but other issues arise).

Sammy, Mo↗
NASA NTRS1992

Secondary instability in rotating-disk flow

Primary instability of the 3D boundary layer on a rotating disk introduces periodic modulation of the mean flow in the form of stationary crossflow vortices. We study the stability of this modulated mean flow with respect to secondary disturbances. Both fundamental and subharmonic resonance cases are considered, and their corresponding results indicate that the growth rate and the frequency of the secondary instability are insensitive to the exact nature of the resonance condition. The threshold primary stationary crossflow vortex amplitude for secondary instability found in this 3D incompressible boundary layer is significantly larger than that for a 2D boundary layer which is subjected to Tollmien-Schlichting instability. The secondary instability results in a pair of travelling counter-rotating vortices, tilted up and oriented at an angle to the primary stationary crossflow vortices.

Balachandar, S.↗
NASA NTRS1982

On higher eigenstates of Goertler instability in compressible flow

The effect of secondary instabilities of Goertler vortices with respect to their growth and amplification was investigated. Instability of viscous flow along a concave surface is in the form of counterrotating streamwise vortices commonly known as Goertler vortices. The effects of suction on higher modes of Goertler vortices are also considered.

Goglia, G. L.↗
NASA NTRS1993

Performance assessment of low pressure nuclear thermal propulsion

An increase in Isp for nuclear thermal propulsion systems is desirable for reducing the propellant requirements and cost of future applications, such as the Mars Transfer Vehicle. Several previous design studies have suggested that the Isp could be increased substantially with hydrogen dissociation/recombination. Hydrogen molecules (H2), at high temperatures and low pressures, will dissociate to monatomic hydrogen (H). The reverse process (i.e., formation of H2 from H) is exothermic. The exothermic energy in a nozzle increases the kinetic energy and therefore, increases the Isp. The low pressure nuclear thermal propulsion system (LPNTP) system is expected to maximize the hydrogen dissociation/recombination and Isp by operating at high chamber temperatures and low chamber pressures. The process involves hydrogen flow through a high temperature, low pressure fission reactor, and out a nozzle. The high temperature (approximately 3000 K) of the hydrogen in the reactor is limited by the temperature limits of the reactor material. The minimum chamber pressure is about 1 atm because lower pressures decrease the engines thrust to weight ratio below acceptable limits. This study assumes that hydrogen leaves the reactor and enters the nozzle at the 3000 K equilibrium dissociation level. Hydrogen dissociation in the reactor does not affect LPNTP performance like dissociation in traditional chemical propulsion systems, because energy from the reactor resupplies energy lost due to hydrogen dissociation. Recombination takes place in the nozzle due primarily to a drop in temperature as the Mach number increases. However, as the Mach number increases beyond the nozzle throat, the static pressure and density of the flow decreases and minimizes the recombination. The ideal LPNTP Isp at 3000 K and 10 psia is 1160 seconds due to the added energy from fast recombination rates. The actual Isp depends on the finite kinetic reaction rates which affect the amount of monatomic hydrogen recombination before the flow exits the nozzle. A LPNTP system has other technical issues (e.g. flow instability and two-phase flow) besides hydrogen dissociation/recombination which affect the systems practicality. In this study, only the effects of hydrogen dissociation/recombination are examined.

Gerrish, Harrold P., Jr.↗
NASA NTRS1987

Calculations of inlet distortion induced compressor flowfield instability

Calculations are presented predicting the onset of flow instability for a multistage low speed axial compressor operating in circumferentially distorted inlet flow. The most important feature of the model used is that it attempts to properly account for the fluid dynamic interaction between the spoiled and unspoiled sectors of the compressor. The calculations show that there is an approximate stability criterion, the annulus averaged slope of the compressor pressure rise characteristic equal to zero, that is valid whenever the dynamics of the compressor distorted flowfield can be considered independent of the compressor environment. This approximate criterion is used to investigate the relationship between the present model and the parallel compressor model. Further calculations are performed to investigate cases of interest when the dynamics of the flowfield are coupled to the environment. Resonant cases and cases when the distortion is unsteady are studied. In particular, it is shown that rotating distortions which propagate in the rotor direction can have a greater effect on stability margin than stationary or counter-rotational ones. Finally, it is shown that the general predictions of the model are insensitive to the details of the unsteady bladerow dynamics.

Hynes, T. P.↗
NASA NTRS1988

On the instability of hypersonic flow past a wedge

The instability of a compressible flow past a wedge is investigated in the hypersonic limit. Particular attention is given to the Tollmien-Schlichting waves governed by triple-deck theory though some discussion of inviscid modes is given. It is shown that the attached shock has a significant effect on the growth rates of Tollmien-Schlichting waves. Moreover, the presence of the shock allows for more than one unstable Tollmien-Schlichting wave. Indeed, an infinite discrete spectrum of unstable waves is induced by the shock, but these modes are unstable over relatively small but high frequency ranges. The shock is shown to have little effect on the inviscid modes considered by previous authors and an asymptotic description of inviscid modes in the hypersonic limit is given.

Cowley, Stephen↗