Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “filler metal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

87 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effects of Plasticizer Content and Ceramic Addition on Electrochemical Properties of Cross-Linked Polymer Electrolyte

The development of a safe electrolyte is the key to improving energy density for next generation lithium batteries. In this work, UV-crosslinked poly(ethylene oxide) (PEO) -based polymer and composite electrolytes are systematically investigated on their ionic conductivity, mechanical and electrochemical properties. The polymer electrolytes are plasticized with non-flammable linear short-chain PEO. In the composite electrolytes, a doped lithium aluminum titanium phosphate (LATP) ceramic, LICGC™, is used as the ceramic filler. It is found that the addition of the plasticizer leads to a tradeoff between ion transport and mechanical properties. In contrast, the addition of ceramic fillers improves both the ionic conductivity and mechanical properties. The sample with 20 wt% of LICGC™ shows a conductivity of ~0.6 mS cm –1 at 50 °C. This sample also demonstrates much longer cycle life than the neat polymer electrolyte in Li platting/stripping test with a capacity of 1 mAh cm –2 . Further, a full cell made with this composite electrolyte against Li metal anode and high voltage LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode shows 94% capacity retention after 30 cycles, compared to 58% capacity retention with the neat polymer electrolyte. These results demonstrate that a hybrid of polymer/ceramic/non-flammable plasticizer is a promising path to high energy density, high voltage lithium batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Heterogeneous creep deformation behavior of functionally graded transition joints (GTJs)

Dissimilar metal welds (DMWs) made between ferritic steels and austenitic alloys are used extensively in high-temperature power plant components. These DMWs experience premature creep failure in the ferritic steel’s heat affected zone (HAZ), close to the weld interface. Steep variations in microstructure and chemical composition across the dissimilar weld interface have been the contributing factors for the failure. Graded transition joints (GTJs), developed by functionally grading the chemical composition in layers, have been proposed as potential candidates to replace DMWs. In this research, GTJ coupons were fabricated between 2.25Cr-1Mo steel and Alloy 800H base material using two filler materials: (i) Inconel 82 and (ii) P87. These samples were aged at 600°C for 2000h to accelerate high-temperature microstructural evolution seen in service conditions, before subjecting them to short-term (~1 month) creep tests. Surface strains were measured using digital image correlation (DIC) technique to extract creep strain rates at different locations within GTJs. Both the GTJs exhibited heterogeneous creep strain distribution. Creep strain accumulated in the FGHAZ of 2.25Cr-1Mo steel, similar to type IV failure associated with Cr-Mo steel weldments. Microstructure based creep model framework was developed to describe the discrete creep strain rates observed in various 2.25Cr-1Mo steel regions of GTJs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fast rise breakdown in dielectric filled air gap for surge protection

Electric discharge across an air gap can be self-healing, providing a unique capability for repetitive, fast, high-voltage/current switching applications through arc conduction. Furthermore, incorporating dielectric granules in the air gap stimulates gas ionization, which lowers the breakdown voltage and narrows breakdown voltage distribution, thereby enabling engineered surge protection from multiple lightning strikes on aerospace vehicles and sensitive solid-state electronics in critical systems. This study investigates the effect of the permittivity of dielectric granules, gap filling, surface roughness, and metal work function on fast-rising, high-voltage breakdowns. In addition to the air gap width, these factors play important roles in gas ionization, field concentration, and initiation of electrical discharge and arcing. Therefore, they could potentially be used to control and narrow operational breakdown voltages for practical applications. Additionally, a modified Langevin–Debye model is developed to correlate the breakdown voltage and the permittivity of the dielectric filler. These investigations identify and highlight key underpinning mechanisms governing the gas discharge behavior across a dielectric filled air gap during voltage surge events.

42 ENGINEERING↗
DOE OSTI2025

Conductive Liquid Metal Vitrimer Composites for Reconfigurable and Recyclable Flexible Electronics

Liquid metal (LM) elastomer composites exhibit excellent functionality for stretchable electronics and wearables, but limited recycling and reuse pathways constrain their sustainable use. Here, to address these challenges amid growing concerns over electronic waste, a conductive LM–vitrimer composite is presented that enables recyclable and reconfigurable electronics. This soft and stretchable composite features uniformly distributed LM inclusions that enhance thermal conductivity by 6.53× and enable the formation of conductive traces with electrical self-healing, while the vitrimer provides structural restoration. The dynamic covalent bonds of the vitrimer matrix are leveraged for both reprocessing the composite and chemically recovering 94% of the LM. This liquid-state filler slightly reduces the vitrimer's stiffness to 2.63 MPa (≈20% lower), while maintaining its high stretchability (>135% strain) and thermal stability. It is further examined how ultrasonicated LM inclusions interact with the vitrimer matrix and demonstrate the composite's self-healing and recyclability through two distinct approaches: 1) thermomechanical reprocessing, which restores fragmented composites under heat and compression for circuit reconfiguration; and 2) chemical recycling, which recovers the embedded LM for reuse in fabricating new composites and redesigned circuitry. With the integration of recyclability and diverse functional capabilities, LM–vitrimer composites emerge as a promising material platform for sustainable, flexible electronics.

Han, Youngshang [Univ. of Washington, Seattle, WA ↗
DOE OSTI2025

Surviving nanoscale interfacial stability in extreme thermal expansion contrast Zn(CN) 2 -epoxy resin matrix composites

Here, we report the remarkable stability at the nanoscale matrix-filler interface in a series of overall low coefficient of thermal expansion (CTE) zinc cyanide (ZC)/epoxy resin composites. These interfaces demonstrate the stability of highly contrasting materials. These composites are designed to optimize the properties of both materials: epoxy resins are valued for their high strength, superb chemical resistance, low dielectric properties, and adhesive abilities. ZC, a model flexible framework, exhibits negative thermal expansion (NTE) behavior and compensates for the epoxy resin’s detrimentally large thermal expansion values. Filled resins minimize the native 65 ppm/°C CTE values to 19 ppm/° C over a wide temperature range while maintaining linearity, yielding composites compatible with typical metal and ceramic substrates’—commonly bonded to the resin— 0–20 ppm/° C CTE values. Additionally, with significant intrinsic differences in the materials, we use wide-angle X-ray diffraction and atomic force microscopy to elucidate thermal movement. The ZC/epoxy interface is surprisingly resilient over 1,000 cycles between -55° C and 75° C, extremes typical to aerospace applications. Further, we show that the resin viscosity remains less than 21 Pa*s at up to 30 vol% ZC, an important consideration for workability. We also discuss settling distribution, glass transition temperature, flexural strength, and longevity. All results point favorably towards practical implementation in low thermal expansion application needs: filling the gap in component design.

42 ENGINEERING↗
DOE OSTI2021

Diversifying Composition Leads to Hierarchical Composites with Design Flexibility and Structural Fidelity

Although significant progress has been made in the self-assembly of nanostructures, present successes heavily rely on precision in building block design, composition, and pair interactions. These requirements fundamentally limit our ability to synthesize macroscopic materials where the likelihood of impurity inclusion escalates and, more importantly, to access molecular-to-nanoscopic-to-microscopic-to-macroscopic hierarchies, since the types and compositions of building blocks vary at each stage. Inspired by biological blends and high-entropy alloys, we hypothesize that diversifying the blend’s composition can overcome these limitations. Increasing the number of components increases mixing entropy, leading to the dispersion of different components and, as a result, enhances interphase miscibility, weakens the dependence on specific pair interactions, and enables long-range cooperativity. This hypothesis is validated in complex blends containing small molecules, block copolymer-based supramolecules, and nanoparticles/colloidal particles. Hierarchically structured composites can be obtained with formulation flexibility in the filler selection and blend composition. It is worth noting that, by adding small molecules, we can solve the size constraint that plagues traditional block copolymer/nanoparticle blends. Detailed characterization and simulation further confirm that each component is distributed to locally mediate unfavorable interactions, cooperatively mitigate composition fluctuations, and retain structural fidelity. Furthermore, the blends have sufficient mobility to access tunable microstructures without compromising the order of the nanostructure. Besides establishing a kinetically viable pathway to release current constraints in the composite design and to navigate uncertainties during structure formation over multiple length scales, the present study demonstrates that entropy-driven behaviors can be realized in systems beyond high-entropy alloys despite inherent differences between metal alloys and organic/inorganic hybrids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

A Quinoidal Two‐Dimensional Metal–Organic Framework for High‐Performance Micro‐Supercapacitors and Solid‐State Lithium Batteries

Two-dimensional (2D) metal-organic frameworks (MOFs) integrating redox-active linkers enable dense charge sites and open ion pathways for microscale energy storage. We report a quinoidal dicarboxylate ligand, AQM-H2L, derived from p-azaquinodimethane, forming crystalline frameworks with Cu2+ and Zn2+ nodes. The Cu-based MOF (AQM-AQM-H2L-Cu) exhibits layered sheets (>14 Å spacing) constructed from dinuclear Cu-carboxylate units and conjugated AQM linkers, which narrow the bandgap and introduce Cu2+/Cu+ pseudocapacitance. Exfoliated nanosheets (∼5 nm) retain crystallinity and excellent processability. Integrated into graphene films, they deliver areal and volumetric capacitances of 29.6 mF cm-2 and 18.1 F cm-3, achieving 2.6 mWh cm-3 energy density at 160 mW cm-3. As ionic fillers (1 wt%) in PEO solid polymer electrolytes, the nanosheets markedly enhance LiFePO4 cell performance, affording 169.8 mAh g-1 at 0.2 C and 93% retention after 400 cycles. This work establishes quinoidal linkers as a compact and robust design motif for ionically active 2D frameworks toward high-performance miniature and solid-state energy devices.

Chen, Ziman↗
DOE OSTI2020

Conductive Adhesives for Metallization of Interdigitated Back Contact Solar Cells

The metallization and interconnection of Si solar cells to form a module is usually a multi-step process: cells are metallized individually, soldered into strings, and subsequently assembled into a module. Furthermore, the metallization process for individual cells must be compatible with the doped surfaces being contacted, which creates additional challenges when moving from diffused junctions to heterojunctions and/or passivated contact structures. To mitigate these problems and streamline module manufacturing for the case of interdigitated back contact (IBC) cell modules, we developed an approach wherein unmetallized IBC cells are bonded directly to a circuitized backsheet using a conductive adhesive (CA) that only conducts out-of-plane. The metal/CA/silicon stack is bonded by hot-pressing at 100-200 degrees C.For a CA consisting of ethylene vinyl acetate (EVA) filled with Ag-coated spheres or indium powder we find that contact resistivities in the range of 1-10 Wcm 2 are obtained, regardless of which conductive filler and which hot pressing parameters are used. XPS revealed that about 1-2 nm EVA residue bonds to the Si in these samples, suggesting the formation of an insulating barrier that is responsible for the high contact resistance. Using indium powder alone, improved contact resistivities <0.6 Wcm 2 , high shunt resistances, and an implied open-circuit voltage loss below 10 mV were obtained. Furthermore, a cost estimate is presented, indicating that substantial cost savings of up to $10/m 2 , or about $0.05/W DC , are possible through CA-based IBC module manufacturing.

14 SOLAR ENERGY↗
DOE OSTI2025

Enhancing cathode composites with conductive alignment synergy for solid-state batteries

Enhancing transport and chemomechanical properties in cathode composites is crucial for the performance of solid-state batteries. Our study introduces the filler-aligned structured thick (FAST) electrode, which notably improves mechanical strength and ionic/electronic conductivity in solid composite cathodes. The FAST electrode incorporates vertically aligned nanoconducting carbon nanotubes within an ion-conducting polymer electrolyte, creating a low-tortuosity electron/ion transport path while strengthening the electrode’s structure. This design not only mitigates recrystallization of the polymer electrolyte but also establishes a densified local electric field distribution and accelerates the migration of lithium ions. The FAST electrode showcases outstanding electrochemical performance with lithium iron phosphate as the active material, achieving a high capacity of 148.2 milliampere hours per gram at 0.2 C over 100 cycles with substantial material loading (49.3 milligrams per square centimeter). This innovative electrode design marks a remarkable stride in addressing the challenges of solid-state lithium metal batteries.

Science & Technology - Other Topics↗
DOE OSTI2024

Salt‐Assisted Vapor–Liquid–Solid Growth of 1D van der Waals Materials

The method of salt-assisted vapor–liquid–solid (VLS) growth is introduced to synthesize 1D nanostructures of trichalcogenide van der Waals (vdW) materials, exemplified by niobium trisulfide (NbS 3 ). The method uses a unique catalyst consisting of an alloy of Au and an alkali metal halide (NaCl) to enable rapid and directional growth. High yields of two types of NbS 3 1D nanostructures, nanowires and nanoribbons, each with sub-ten nanometer diameter, tens of micrometers length, and distinct 1D morphology and growth orientation are demonstrated. Strategies to control the location, size, and morphology of growth, and extend the growth method to synthesize other transition metal trichalcogenides, NbSe 3 and TiS 3 , as nanowires are demonstrated. Finally, the role of the Au–NaCl alloy catalyst in guiding VLS synthesis is described and the growth mechanism based on the relationships measured between structure (growth orientation, morphology, and dimensions) and growth conditions (catalyst volume and growth time) is discussed. These results introduce opportunities to expand the library of emerging 1D vdW materials to make use of their unique properties through controlled growth at nanoscale dimensions.

1D van der Waals material↗
DOE OSTI2022

Li Morphology Evolution during Initial Cycles in a Gel Composite Polymer Electrolyte

Understanding and controlling lithium morphology evolution and lithium dendrite formation and growth during cycling is one of the key challenges for high-energy lithium metal batteries. This challenge applies to liquid electrolyte batteries as well as solid-state and semi-solid-state batteries. Our current knowledge about the evolution of the Li morphology is mostly obtained from liquid electrolyte-based studies in a Li–Li symmetrical cell configuration. The knowledge obtained in such conditions may not readily transfer into solid-state or semi-solid-state batteries. In this work, Li morphology evolution during initial cycling in a full cell configuration with the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NMC 622) cathode and a semi-solid-state gel composite electrolyte is monitored via post-mortem photographs and scanning electron microscopy at multiple length scales. The gel composite electrolyte contains a cross-linked poly(ethylene oxide)-based polymer electrolyte, ceramic fillers, and a liquid plasticizer. The results show that severe surface pitting occurs as early as the second stripping cycle. Pit formation and continuous dissolution during the stripping process are the main cause of the Li surface roughening and dendrite growth mechanism in the model gel composite electrolyte. Comparing Li dendrite growth mechanisms in liquid, polymer, and ceramic solid electrolytes, the dendrite growth mechanism observed in this model electrolyte resembles that of the liquid electrolyte the most. This study suggests that strategies to control Li morphology and prevent dendrite growth in a gel composite electrolyte should be similar to strategies applicable to liquid electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2025

Mg vacancy and impurity-limited MgO single crystal thermal conductivity

Magnesium oxide (MgO) exhibits one of the highest thermal conductivities among oxides and is widely used as a dielectric material and substrate in semiconductor devices, in refractory applications, and as a promising filler in thermal interface materials for electronics. Its high thermal conductivity may be sensitive to impurity and defects, yet this influence is still uncertain. Here, in this study, the impact of the common impurities, i.e., Al, Ca, Ti, V, Fe, Si, B, Nb, Zr, Na, and K, as well as Mg and O vacancies on phonon scattering and thermal conductivity of MgO is studied using a fully first-principles T-matrix framework. It is found that B, Nb, and Zr impurities, along with Mg vacancies, lead to exceptionally strong reductions in thermal conductivity. By contrast, O vacancies and other impurities have modest to minimal impacts. Leveraging the T-matrix results, we reassess the perturbative, mass-only formalism whose use is pervasive in the literature and show that neglecting bond disorder does not necessarily lead to underestimation: for all transition-metal impurities studied, bond perturbations partially cancel mass disorder, causing the traditional perturbative model to overestimate scattering. We propose a simple modified perturbative expression that incorporates both mass and bond disorder and closely reproduces the T-matrix trends. Our predicted low-temperature trends by including phonon-impurity and phonon-boundary scattering match reasonably well with experiments. This work provides an in-depth study of impurity- and vacancy-limited thermal conductivity of MgO and suggests that reported “high-purity” MgO values have likely not yet reached the intrinsic upper limit, which may be substantially higher.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Enhanced Surface Interactions Enable Fast Li + Conduction in Oxide/Polymer Composite Electrolyte

Abstract Li + ‐conducting oxides are considered better ceramic fillers than Li + ‐insulating oxides for improving Li + conductivity in composite polymer electrolytes owing to their ability to conduct Li + through the ceramic oxide as well as across the oxide/polymer interface. Here we use two Li + ‐insulating oxides (fluorite Gd 0.1 Ce 0.9 O 1.95 and perovskite La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 2.55 ) with a high concentration of oxygen vacancies to demonstrate two oxide/poly(ethylene oxide) (PEO)‐based polymer composite electrolytes, each with a Li + conductivity above 10 −4 S cm −1 at 30 °C. Li solid‐state NMR results show an increase in Li + ions (>10 %) occupying the more mobile A2 environment in the composite electrolytes. This increase in A2‐site occupancy originates from the strong interaction between the O 2− of Li‐salt anion and the surface oxygen vacancies of each oxide and contributes to the more facile Li + transport. All‐solid‐state Li‐metal cells with these composite electrolytes demonstrate a small interfacial resistance with good cycling performance at 35 °C.

Wu, Nan↗
DOE OSTI2020

Understanding Materials Characteristics of Palladium Lanthanide Cermet Wires as a Mimic of Californium Wire Production

Californium-252 (Cf-252) has been synthesized on a large scale (mg) since the 1970s for use as a portable neutron source. With a half-life of 2.645 years and a spontaneous fission fraction of 3.09%, Cf-252 emits 2.31 × 10 12 neutrons/gram second. Today most of the Cf-252 produced in the world is made at Oak Ridge National Laboratory (ORNL) using the High Flux Isotope Reactor (HFIR) and the Radiochemical Engineering Development Center (REDC). Because of its highly radioactive nature, all manipulations of Cf-252 need to be performed in hot cell facilities by highly trained personnel. The Cf-252 produced at ORNL is done at the REDC, which is conveniently located next to the HFIR. Cf-252 is sold as bulk wire, which has been described as palladium (Pd) metal incasing californium oxide (Cf 2 O 3 ). The process was developed by Mosley et al. at Savannah River Laboratory (SRL) where it was modeled after the thorium work done by Fuschillo et al. This process has been used since the 1970s to synthesize this unique wire, but its fundamental chemistry and materials characteristics were never openly reported. Here we aim to better understand the chemistry and the materials characteristics of Cf-252 wire production for process improvements and to better our fundamental understanding of the mid-late actinides. Though there are many challenges in working with radioactive elements such as Cf, the isotope Cf-252 is even more complicated due to its neutron emission. One challenge with neutron emission is the ability of neutrons to penetrate much deeper through materials, causing radiation damage. This makes using instrumentation to characterize the chemistry and materials properties of this process difficult. For this reason, this study will first focus on terbium (Tb) as a surrogate for Cf. Currently Tb is used as a carrier or filler in Cf production when small amounts of Cf are being processed. This, along with their similar size and charge, makes Tb a reasonable surrogate for this study.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microwave-driven synthesis and modification of nanocarbons and hybrids in liquid and solid phases

Over the past 20 years, nanocarbons have become more significant as nanostructured fillers in composites and, more recently, as functional elements in a brand-new class of hybrid materials. Microwave-assisted synthesis and processing is a burgeoning subject matter in materials research with significant strides in the realm of nanocarbon during the last decade. Here, the review examines recent approaches to producing various nanocarbons using microwaves as energy sources, the characterization of such materials for various applications, and their results. The underlying factors supporting the increased performance of such materials or their composites are analyzed and reaction mechanisms are presented wherever necessary. In particular, the recently developed and verified approaches to produce porous carbon materials, CNTs and fibers, carbon nanospheres, carbon dots, CQDs, reduced graphene oxide, nanocarbon hybrid materials, and the purification and modification of CNTs are discussed. The reduction of graphene oxide and the preparation of graphene derivative hybrids using solid-state and liquid-state routes such as polyopl, mixed solvents, ionic liquids, and microwave-assisted hydrothermal/solvothermal methods are analyzed in detail. In addition, the principles of microwave heating in liquid and solid states, the use of metals particles as arcing agents or catalysts, and carbonaceous materials as internal or external susceptors during synthesis and modifications are presented in detail.

25 ENERGY STORAGE↗