Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrode fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fabrication of porous transport electrodes: Development of quantitative approach for quality control

This work focuses on porous transport electrodes (PTEs), which integrate the anodic catalyst with the adjacent Ti porous transport layer (PTL). Challenges in catalyst deposition on PTLs, particularly at low loadings, motivated this study to evaluate various fabrication methods and characterization approaches. This work investigated Pt-treated PTLs coated with Ir-based catalysts using several common methods, including airbrush coating, rod coating, ultrasonic spray coating, electrodeposition, and sputter deposition, with catalyst loadings ranging from 2.9 to 0.1 mg/cm 2 , providing the opportunity for comparisons across a large set of samples produced by different methods. Two widely accessible characterization techniques: X-ray computed tomography (XCT) and scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) were explored. Initial evaluation of selected samples with XCT provided qualitative insights into catalyst distribution, however comprehensive quantitative analysis was limited. SEM-EDS enabled detailed information on the catalyst distribution both qualitatively and quantitatively using two metrics. Atomic and surface area % ratios of Pt:Ir and Ti:Ir revealed trends in catalyst loading and losses into the PTL pores, as well as evaluating the homogeneity of catalyst coatings. The analysis demonstrated that ultrasonic spray coating, electrodeposition, and sputter coating produced the most homogeneous coatings, with minimal catalyst losses observed for electrodeposition and sputter coating. By adapting common techniques with novel, standardized methodologies, this work establishes a universally applicable framework for cross-study comparison of PTEs. The SEM-EDS approach provides a practical, accessible tool for PTE characterization and contributes a reference dataset supporting both research development and rapid quality control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fabricating Silver Nanowire–IZO Composite Transparent Conducting Electrodes at Roll-to-Roll Speed for Perovskite Solar Cells

This study addresses the challenges of efficient, large-scale production of flexible transparent conducting electrodes (TCEs). We fabricate TCEs on polyethylene terephthalate (PET) substrates using a high-speed roll-to-roll (R2R) compatible method that combines gravure printing and photonic curing. The hybrid TCEs consist of Ag metal bus lines (Ag MBLs) coated with silver nanowires (AgNWs) and indium zinc oxide (IZO) layers. All materials are solutions deposited at speeds exceeding 10 m/min using gravure printing. We conduct a systematic study to optimize coating parameters and tune solvent composition to achieve a uniform AgNW network. The entire stack undergoes photonic curing, a low-energy annealing method that can be completed at high speeds and will not damage the plastic substrates. The resulting hybrid TCEs exhibit a transmittance of 92% averaged from 400 nm to 1100 nm and a sheet resistance of 11 Ω/sq. Mechanical durability is tested by bending the hybrid TCEs to a strain of 1% for 2000 cycles. The results show a minimal increase (<5%) in resistance. The high-throughput potential is established by showing that each hybrid TCE fabrication step can be completed at 30 m/min. We further fabricate methylammonium lead iodide solar cells to demonstrate the practical use of these TCEs, achieving an average power conversion efficiency (PCE) of 13%. The high-performance hybrid TCEs produced using R2R-compatible processes show potential as a viable choice for replacing vacuum-deposited indium tin oxide films on PET.

14 SOLAR ENERGY↗
DOE OSTI2025

Long carbon fibers boost performance of dry processed Li-ion battery electrodes

Dry processing (DP) is an advanced manufacturing technique for lithium-ion battery (LIB) electrodes. Unlike conventional wet-process-based manufacturing that involves dissolving polyvinylidene fluoride (PVDF) binder in n-methyl-2-pyrrolidone (NMP) solvent for slurry-casting, DP involves fibrillation of polymer binders. This method offers environmental and cost benefits by eliminating the need for expensive and environmentally hazardous organic solvents. However, DP-produced electrode films often lack mechanical stability due to the absence of a current collector substrate during electrode material layer fabrication. This reduced mechanical instability results in difficulty during fabricating of thin electrodes (≈5 mAh/cm 2 ). To address this issue, long (>8 mm) carbon fiber (CF) has been incorporated to reinforce the mechanical strength of the electrode films. In conclusion, the study demonstrates that the inclusion of long carbon fiber boosts the mechanical, electrical, thermal, and electrochemical performance of DP electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Meso-Structured Polymer Electrolyte Fuel Cell Electrode

Increasing the utilization of Pt and Pt alloy catalysts in polymer electrolyte fuel cell cathodes is critical to improving the high power density operation, particularly at low Pt loadings. State of the art electrodes are fabricated in an ink deposition process that leads to uncontrolled electrode architecture with random aggregates of functional domains (catalyst, ionomer, and pore volume) (1). The randomness in the domains induces high tortuosity transport pathways for ions and fluids, which cause severe transport resistance during high current density operation. Thin ionomer films cause additional transport resistance and poisoning of the Pt catalyst, which becomes more significant at low Pt loadings. Reducing the amount of ionomer in the catalyst domain without affecting the ionic transport resistance is key to improving the utilization of the Pt and reducing the transport resistance at low Pt loading. Rational design of the electrode structure with controlled low tortuous ionic transport pathways could improve performance. The introduction of the ionomer pathways could also enable reduction of the ionomer volume in the catalyst domain, reducing the transport resistance. Middelmen et al. proposed electrode structures consisting of aligned components in a low tortuosity configuration to improve performance (2). In this work, we present an alternative electrode structure based on a vertically aligned array of Nafion pillars in the cathode catalyst layer, as shown in Figure 1a. Figure 1b shows the SEM image of the Nafion pillars. Furthermore, Pt supported on carbon catalyst was deposited on the Nafion pillars to fabricate a meso-structured electrode. Nafion pillars provide high conductive and low tortuous pathways for protons, reducing the effective transport distance, and enabling reduction of the ionomer binder in the catalyst domain.

25 ENERGY STORAGE↗
DOE OSTI2024

Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes

A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.

08 HYDROGEN↗
DOE OSTI2022

Solvent-Free Manufacturing of Lithium-Ion Battery Electrodes via Cold Plasma

Slurry casting has been used to fabricate lithium-ion battery electrodes for decades, which involves toxic and expensive organic solvents followed by high-cost vacuum drying and electrode calendering. This work presents a new manufacturing method using a nonthermal plasma to create inter-particle binding without using any polymeric binding materials, enabling solvent-free manufacturing electrodes with any electrochemistry of choice. The cold-plasma-coating technique enables fabricating electrodes with thickness (>200 μm), high mass loading (>30 mg cm -2 ), high peel strength, and the ability to print lithium-ion batteries in an arbitrary geometry. This crosscutting, chemistry agnostic, platform technology would increase energy density, eliminate the use of solvents, vacuum drying, and calendering processes during production, and reduce manufacturing cost for current and future cell designs. Here, lithium iron phosphate and lithium cobalt oxide were used as examples to demonstrate the efficacy of the cold-plasma-coating technique. It is found that the mechanical peel strength of cold-plasma-coating-manufactured lithium iron phosphate is over an order of magnitude higher than that of slurry-casted lithium iron phosphate electrodes. Full cells assembled with a graphite anode and the cold-plasma-coating-lithium iron phosphate cathode offer highly reversible cycling performance with a capacity retention of 81.6% over 500 cycles. For the highly conductive cathode material lithium cobalt oxide, an areal capacity of 4.2 mAh cm -2 at 0.2 C is attained. We anticipate that this new, highly scalable manufacturing technique will redefine global lithium-ion battery manufacturing providing significantly reduced plant footprints and material costs.

25 ENERGY STORAGE↗
DOE OSTI2020

Improving the bulk gas transport of Fe-N-C platinum group metal-free nanofiber electrodes via electrospinning for fuel cell applications

To overcome transport limitations associated with thicker platinum group metal-free (PGM-free) electrodes, it's essential to investigate and tailor alternative electrode architectures to maximize the bulk electrode transport properties, whilst not significantly impeding electrocatalyst active site accessibility and electrode proton resistance. In this work, PGM-free nanofiber electrode mats, prepared by electrospinning a mixture of pyrolyzed Fe-N-C catalyst, Nafion ionomer and a carrier polymer Poly Acrylic acid (PAA), were compared to traditionally prepared electrodes. The morphological properties and elemental distribution of the fabricated nanofiber electrodes showed that the exterior surface of the PGM-free nanofibers was conformally covered with a thin ionomer film. Electrochemical diagnostics performed utilizing cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and H 2 -limiting current measurements, revealed an increase in electric double layer capacitance, reduction in electrode proton transport and a significant improvement in bulk-electrode gas transport properties for the nanofiber electrodes, supporting the observed performance increase from electrochemical polarization data obtained in H 2 -O 2 /Air fuel cells. At 100% RH in H2/Air, the power density of the nanofiber electrodes increased ca. 50% vs. the traditionally prepared electrodes (ca. 260 vs 175 mW cm -2 ), which was attributed to a less tortuous molecular diffusion pathway and an associated reduction in the pressure dependent and independent gas transport resistances in the nanofiber electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Electrodeposition for Low-Cost, Water-Based Electrode Manufacturing. Research Performance Progress Report, Jan. 1, 2016 - Dec. 31, 2019

The viability of electrocoat to fabricate battery electrodes at commercially relevant formulations has been demonstrated using both bench-scale equipment and a small pilot-scale roll-to-roll system (mini-coater). Through this, we show that an electrodeposited lithium-ion battery electrode coating system and manufacturing process is capable of reducing cell costs. Specifically, >60% decrease in capital costs is expected when transitioning from slot-die to electrocoat-based coating systems due to the removal of a solvent recovery system. In addition, a 50% reduction in operating costs in also expected as we enable 2-coat/2-cure processing of cathode electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Copper Electrode on Flexible Substrate by Intense Pulsed Light Sintering of Microsized Copper Particles

Metal electrodes deposited in a grid pattern onto flexible polymer substrates have been shown to be a viable alternative to replace indium tin oxide (ITO) as the transparent anode for organic photovoltaics. copper may be a better alternative in terms of cost and stability for large area low-cost solar modules, specifically on roll-to-roll platforms. These customized electrode patterns can be fabricated from copper nanoparticles through various printing techniques applicable to solution phase processing. The Intense Pulsed Light (IPL) technique has been used to sinter copper nanoparticles (~100nm) to fabricate conductive copper electrodes on flexible polymer substrates. However, compared to nanosized (~100 nm) copper particles, microsized (~2 um) copper is much cheaper. In this work, microsized (~2 um) copper is used to produce high conductive copper inks. The conductivity of the print can be adjusted through the use of surfactant. IPL sintering was optimized to obtain high conductivity copper films. In conclusion, several microscopic and electrical spectroscopic characterization techniques such as scanning electron microscopy (SEM), x-ray diffraction (XRD), 4-point probe resistivity measurements were employed to characterize the copper electrodes.

14 SOLAR ENERGY↗
DOE OSTI2025

Stability of Mn-Doped TiO 2 Thin-Film Anodes during Water Oxidation Reactions

Incorporating manganese atoms into TiO 2 has been shown to improve its activity for water oxidation. However, its activity has been observed to steadily degrade under constant applied potential, especially at more oxidizing applied potentials. Here, the compositional profile and electrochemical stability of Mn-doped TiO 2 (Mn:TiO 2 ) thin-film electrodes precisely fabricated by atomic layer deposition (ALD) were evaluated to elucidate the mechanisms of electrode degradation. Although ALD enables the deposition of Mn dopants throughout the film thickness, only Mn within 1.5 nm of the surface was observed to be redox active. Annealing Mn:TiO 2 films in air leads to the diffusion of Mn toward the electrode surface and oxidation of the Mn and alters the redox behavior. Annealing endows greater stability to Mn redox behavior but does not fully stabilize the water oxidation current, suggesting that the two electrochemical processes are not precisely correlated. In situ inductively coupled plasma mass spectrometry reveals that Mn is lost from Mn:TiO 2 films at potentials greater than 1.8 V vs RHE. However, the initial Mn loss is equivalent to less than a single ALD layer of MnO x . Longer-term constant potential experiments suggest that Mn is lost from up to 1 nm of the electrode surface but that this loss may account for only a portion of the diminished water oxidation activity.

atomic layer deposition↗
DOE OSTI2023

Accelerating Battery Simulations by Using High Performance Computing and Opportunities with Machine Learning

The US Department of Energy (DOE) estimates that the battery pack cost of $60 per kilowatt-hour while increasing the driving range to over 300 miles and vehicle charging under 15 min or less would enable mass penetration of electric vehicles in the USA by 2030. These projections are based on the currently available high-density cell chemistry combined with a system level design and optimized electrodes. Electrodes for current state-of-the-art lithium-ion cell technology are fabricated from electrode slurry comprising of active material, polymeric binder, and conductive diluent such as carbon black that are coated on metal current collectors such as copper and aluminum. Given these challenging requirements for development of electrical energy storage devices for future transportation needs, a predictive simulation capability which can accelerate design by considering performance and safety implications of different geometry, materials, and chemistry choices is required. In this chapter, we discuss our state-of-the-art three-dimensional modeling framework, providing examples on battery performance and safety simulations. We also present approaches to use machine learning in the context of large datasets that are becoming available.

Allu, Srikanth↗
DOE OSTI2024

Complex polycation redox material interfaced with renewable porous carbon for asymmetric supercapacitors

Mixed polycation transition metal ferrites are known to exhibit unique and superior characteristics for structural, electrical, magnetic, and optical applications. Although a few binary transition metal ferrites are found to be suitable for electrochemical energy storage application, ternary transition metal ferrites are not investigated for asymmetric supercapacitors (ASCs). Mixed polycation oxides are expected to have increased active sites that can facilitate proton and electron transfer impacting the redox reactions. Specific crystal structure and associated lattice parameters as well as surface and morphological characteristics can also influence the energy storage properties. This study for the first time reports a novel complex polycation redox material, (Cu p Mn q Zn r ) x Fe y O z and renewable pinewood (PW) derived porous carbon (POC) as electrodes for ASC. Both (Cu p Mn q Zn r ) x Fe y O z and PW-POC are subjected to electrochemical characterization and used in ASC configuration with aqueous KOH electrolyte. It is anticipated that the Faradaic characteristics of (Cu p Mn q Zn r ) x Fe y O z will make it to serve as a cathode while PW-POC with capacitive behavior will act as anode in ASCs. Relatively higher specific capacitance of > 200 F/g is observed for the (Cu p Mn q Zn r ) x Fe y O z reference electrode and fabricated ASCs. Capacitance retention rate is tested in 10,000 cycles for the working electrodes whereas for ASC, the stability tests are performed over 100 charging-discharging cycles exhibiting relatively higher capacitance retention. (Cu p Mn q Zn r ) x Fe y O z appears to be a promising material for a supercapacitor.

(CupMnqZnr)xFeyOz↗
DOE OSTI2021

High Energy Density and Stable Three-Dimensionally Structured Se-Loaded Bicontinuous Porous Carbon Battery Electrodes

Here, 3D structured Se-loaded bicontinuous porous carbon (BPC) electrodes were fabricated through colloidal templating of BPC followed by pulsed-voltage Se electrodeposition. The resultant electrodes were found to deliver a specific capacity of 665 mA h g -1 at a rate of 0.1 C, near the theoretical value for Se. When a vinylene carbonate containing electrolyte was utilized, the capacity fade over 500 cycles at 1 C rate was as small as a few percent. Impedance measurements and physical characterization of cycled electrodes indicated the exceptionally stable cycling performance was possibly due to vinylene carbonate resulting in formation of a stable SEI during cycling. Along with cycling stability, the rate performance of the 3D Se/BPC electrodes was also good. Due to the bicontinuous structure of carbonaceous current collector at rates as high as 5 C, the deliverable capacity was about 300 mA h g -1 .

25 ENERGY STORAGE↗
DOE OSTI2023

Carbon Electrode with Sputtered Au Coating for Efficient and Stable Perovskite Solar Cells

Halide perovskite solar cells (PSCs) represent a low-cost and high-efficiency solar technology. However, most of the highly efficient PSCs need a noble electrode, such as Au, through thermal evaporation. Here it is reported that a sputtered Au electrode on a PSC could damage the organic hole transport layer (HTL) and the perovskite layer. Here, we report a simple, yet effective sputtered gold nanoparticle decorated carbon electrode to fabricate efficient and stable planar PSCs. The sputtered Au layer on the doctor-bladed coated carbon electrode can be directly applied to the perovskite semicells by mechanical stacking. By optimizing the gold thickness, a power conversion efficiency (PCE) of 16.87% was obtained for the composite electrode-based PSC, while the reference device recorded a PCE of 12.38%. The composite electrode-based device demonstrated 96% performance retention after being stored under humid conditions (50-60%) without encapsulation for ~100 h. This demonstrates a promising pathway toward the commercialization of large-scale manufacturable sputtered electrodes for the PSC solar module.

14 SOLAR ENERGY↗
DOE OSTI2022

Multiplexed Anodic Stripping Voltammetry Detection of Heavy Metals in Water Using Nanocomposites Modified Screen-Printed Electrodes Integrated With a 3D-Printed Flow Cell

In this study, we present multiplexed anodic stripping voltammetry (ASV) detection of heavy metal ions (HMIs)—As(III), Cd(II), and Pb(II)—using a homemade electrochemical cell consisting of dual working, reference and counter screen-printed electrodes (SPE) on polyimide substrate integrated with a 3D-printed flow cell. Working and counter electrodes were fabricated by the screen-printing of graphite paste while the Ag/AgCl paste was screen-printed as a reference electrode (Ag/AgCl quasi-reference electrode). The working electrodes were modified with (BiO) 2 CO 3 -reduced graphene oxide (rGO)-Nafion [(BiO) 2 CO 3 -rGO-Nafion] and Fe 3 O 4 magnetic nanoparticles (Fe 3 O 4 MNPs) decorated Au nanoparticles (AuNPs)-ionic liquid (IL) (Fe 3 O 4 -Au-IL) nanocomposites separately to enhance HMIs sensing. Electrochemical detection was achieved using square wave ASV technique. The desired structure of the flow electrochemical cell was optimized by the computational fluid dynamic (CFD). Different experimental parameters for stripping analysis of HMIs were optimized including deposition time, deposition potential and flow rate. The linear range of calibration curves with the sensing nanocomposites modified SPE for the three metal ions was from 0–50 μg/L. The limits of detection (S/N = 3) were estimated to be 2.4 μg/L for As(III), 1.2 μg/L for Pb(II) and 0.8 μg/L for Cd(II). Furthermore, the homemade flow anodic stripping sensor platform was used to detect HMIs in simulated river water with a 95–101% recovery, indicating high selectivity and accuracy and great potential for applicability even in complex matrices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Compositions and methods for energy storage device electrodes

An energy storage device can include a cathode, an anode, and a separator between the cathode and the anode, where the anode and/or electrode includes an electrode film having a super-fibrillized binder material and carbon. The electrode film can have a reduced quantity of the binder material while maintaining desired mechanical and/or electrical properties. A process for fabricating the electrode film may include a fibrillization process using reduced speed and/or increased process pressure such that fibrillization of the binder material can be increased. The electrode film may include an electrical conductivity promoting additive to facilitate decreased equivalent series resistance performance. Increasing fibrillization of the binder material may facilitate formation of thinner electrode films, such as dry electrode films.

Raman, Santhanam↗