Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrode fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Designing the Platinum Catalyst Layer for Improved Performance and Durability in Anion Exchange Membrane Water Electrolysis

To lower the cost of hydrogen produced by anion exchange membrane water electrolysis (AEMWE), it is critical to reduce the use of platinum group metal (PGM) catalysts within the device. While iridium has been successfully replaced with PGM-free catalysts at the anode, platinum-based (Pt) cathode catalysts are still required to meet the activity and durability targets. This study investigates the impact of commercial Pt/C catalyst loading, ionomer type and content, and electrode fabrication method on the cathode catalyst layer properties and AEMWE performance with the aim of determining the feasibility of reduced Pt loadings. While increased Pt loading is found to improve beginning-of-life performance, the effects are minimal above 0.6 mg/cm 2 . Ink characterization shows that ionomer type and content affect the ink stability, particle size, and percent of unbound ionomer, which further impact the homogeneity of the sprayed catalyst layers. The 5% PiperION cathode exhibited the highest performance, which may be attributed to a balance between the small particle size and the low proportion of unbound ionomer, minimizing kinetic and transport losses. Theoretical calculations show that the ionomers interact differently with the Pt surface, causing different surface charges and water adsorption strength and activating different mechanisms for hydrogen evolution. Pt-PiperION lowered the enthalpy of water-splitting by 0.1 eV compared to Pt alone and allowed for equal site access between adsorbed H* and OH* (both adsorbed at circa −2.2 eV). Although catalyst-coated membrane (CCM) fabrication techniques are desirable for scale-up, no performance enhancement is observed compared with the catalyst-coated substrate approach. Durability, as measured by degradation rates, Pt loss, and catalyst layer restructuring, was found to improve with increased Pt loadings, higher ionomer content, and CCM architectures. These findings provide important insight into the significant role of the cathode in AEMWE and strategies for maintaining the performance with low Pt loading or PGM-free catalysts.

08 HYDROGEN↗
DOE OSTI2021

Electrochemical CO 2 Reduction Reaction over Cu Nanoparticles with Tunable Activity and Selectivity Mediated by Functional Groups in Polymeric Binder

Electrochemical carbon dioxide reduction reaction (CO 2 RR) using copper (Cu)-based catalysts has received significant attention mainly because Cu is an element capable of producing hydrocarbons and oxygenates. One possible way to control the CO 2 RR performance at the electrode interface is by modifying catalysts with specific functional groups of different polymeric binders, which are necessary components in the process of electrode fabrication. However, the modification effect of the key functional groups on the CO 2 RR activity and selectivity is poorly understood over Cu-based catalysts. In this work, the role of functional groups (e.g., -COOH and -CF 2 groups) in hydrophilic and hydrophobic polymeric binders on the CO 2 RR of Cu-based catalysts is investigated using a combination of electrochemical measurements, in-situ characterization and density functional theory (DFT) calculations. DFT results reveal that functional groups influence the binding energies of key intermediates involved in both CO 2 RR and the competing hydrogen evolution reaction, consistent with experimental observation of binder-dependent product distributions among formic acid, CO, CH 4 , and H 2 . This study provides a fundamental understanding that the selection of desired polymeric binders is a useful strategy for tuning the CO 2 RR activity and selectivity.

25 ENERGY STORAGE↗
DOE OSTI2020

Si-based materials for lithium-ion batteries X: 70% surface-modified Si/C/polyvinylidine difluoride-carbon black/lithiated polyacrylic acid electrode

X-ray photoelectron spectroscopy was used to analyze a 70% Si/C/polyvinylidine difluoride/carbon black/lithiated polyacrylic acid electrode fabricated at the Cell Analysis, Modeling, and Prototyping Facility (CAMP), Argonne National Laboratory. The spectra were obtained using incident monochromatic Al Kα radiation at 1486.6 eV (0.834 01 nm). A survey spectrum together with O 1s, C 1s, and Si 2p are presented. The spectra indicate the principal core level photoelectron and Auger electron signals with only minor copper and lithium signals and show the expected silicon-carbon and silicon-fluorine species related to the surface modification process in addition to oxidized carbon and silicon due to atmospheric exposure.

Haasch, Richard T. (ORCID:0000000194792595)↗
DOE OSTI2020

Elucidating the Role of Ionomer in the Performance of Platinum Group Metal-free Catalyst Layer via in situ Electrochemical Diagnostics

The ionomer content in platinum group metal (PGM)-free polymer electrolyte fuel cell (PEFC) cathode catalyst layer (CCL) plays an important role in the electrode gas transport properties, proton conductivity, and hence, membrane electrode assembly (MEA) performance. In this work, the ionomer content in the CCL is varied, influencing electrode microstructure by altering porosity, tortuosity, as well as ionomer distribution and coverage of the catalyst particles. A novel technique consisting of a H 2 pump, combined with a Pt black sensor layer, is used to measure the bulk mass transport resistance of a series of PGM-free CCL prepared with different ionomer contents. The values for bulk electrode mass transport resistance are contrasted with electrode proton transport resistance in the cathode catalyst layer, establishing a clearly defined trade-off between two key performance limiting phenomena and identifying a need for novel PGM-free electrode fabrication strategies.

25 ENERGY STORAGE↗
DOE OSTI2023

Stationary Direct Methanol Fuel Cells Using Pure Methanol

This project developed stationary direct methanol fuel cells (DMFCs) using pure methanol as the fuel, integrating complementary institutional expertise on platinum group metals free (PGM-free) cathode catalyst (UB), supported anode catalysts (KSU), electrode fabrication, characterization, and optimization (CMU), and multi-phase mass transfer (KU). The proposed cost-effective prototype will deliver reliable and durable performance using a methanol-tolerant PGM-free cathode and a high-performance anode with low PtRu loading. At the end of the project, the research team is expected to deliver a single cell (50 cm 2 ) with ≤3 mg PGM /cm 2 that achieves 300 mW/cm 2 using pure methanol.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

High-Performance AEM LTE with Advanced Membranes, Ionomers and PGM-Free Electrodes

Alkaline low temperature electrolysis (LTE) systems enjoy several potential advantages over acid-based LTE systems including facile oxygen evolution reaction (OER) kinetics and electrodes that can use little to no platinum group metals (PGM). The polymer membranes and membrane electrode assembly (MEA) structures going into alkaline electrochemical systems have seen significant advances in recent years. The objective of this project is to combine state-of-the-art alkaline polymer electrolyzer components into one optimized membrane electrode assembly (MEA) system to achieve DOE low temperature electrolysis (LTE) goals. The benefit of individual component advances cannot be fully appreciated until all aspects and components of the MEA are working at an equally high level of performance. New electrode fabrication methods were developed where solvent cast catalyst/ionomer solutions were used in place of insoluble ionomers to significantly improve adhesion. The membranes were improved in terms of durability and mechanical properties. The OER and HER catalysts were improved and made more durable.

08 HYDROGEN↗
DOE OSTI2025

Development of Li–S Battery Cells with High Energy Density and Long Cycling Life

Lithium–sulfur (Li–S) batteries are considered one of the most promising next-generation energy storage technologies for electric vehicles, owing to their high energy density (up to three times greater than current lithium-ion batteries) and the low cost of sulfur (approximately 100 times cheaper than conventional cobalt oxide). However, several challenges hinder their commercial viability, including the electronically and ionically insulating nature of sulfur, polysulfide dissolution, and lithium dendrite growth. These issues significantly limit battery energy density and cycle life and must be addressed to enable successful commercialization. Current strategies involving porous carbon structures, additives, and electrocatalyst engineering have not fully resolved the polysulfide dissolution problem. While polysulfide-free cathode materials offer a promising solution, they often suffer from low sulfur content, leading to reduced discharge capacity and sluggish reaction kinetics. To overcome these limitations, we have developed novel soluble-polysulfide-free sulfur cathode active materials with a high sulfur content (>50 wt%). By integrating these cathodes with functional binders, optimized electrolyte formulations, and refined electrode fabrication techniques, we demonstrate Li–S batteries with both high energy density and long cycle life. This advancement brings the realization of low-cost, high-energy Li–S batteries significantly closer to practical application.

25 ENERGY STORAGE↗
DOE OSTI2022

Best Practices in PEC Water Splitting: How to Reliably Measure Solar-to-Hydrogen Efficiency of Photoelectrodes

Photoelectrochemical (PEC) water splitting, which utilizes sunlight and water to produce hydrogen fuel, is potentially one of the most sustainable routes to clean energy. One challenge to success is that, to date, similar materials and devices measured in different labs or by different operators lead to quantitatively different results, due to the lack of accepted standard operating procedures and established protocols for PEC efficiency testing. With the aim of disseminating good practices within the PEC community, we provide a vetted protocol that describes how to prepare integrated components and accurately measure their solar-to-hydrogen (STH) efficiency (η STH ). This protocol provides details on electrode fabrication, η STH test device assembly, light source calibration, hydrogen evolution measurement, and initial material qualification by photocurrent measurements under monochromatic and broadband illumination. Common pitfalls in translating experimental results from any lab to an accurate STH efficiency under an AM1.5G reference spectrum are discussed. A III–V tandem photocathode is used to exemplify the process, though with small modifications, the protocol can be applied to photoanodes as well. Dissemination of PEC best practices will help those approaching the field and provide guidance for comparing the results obtained at different lab sites by different groups.

08 HYDROGEN↗
NASA NTRS1984

Plated Metal Powders for Electrode Pastes

Metal grains to be sintered precoated with frit metal. Coated metal powders used to make ink-like electrode pastes for printing and sintering electrode-fabrication process. Grains of base metal coated with lowmelting-point--, lead or tin-- by electroless deposition.

Bickler, D. B.↗
NASA NTRS1989

Mercury ion thruster technology

The Mercury Ion Thruster Technology program was an investigation for improving the understanding of state-of-the-art mercury ion thrusters. Emphasis was placed on optimizing the performance and simplifying the design of the 30 cm diameter ring-cusp discharge chamber. Thruster performance was improved considerably; the baseline beam-ion production cost of the optimized configuration was reduced to Epsilon (sub i) perspective to 130 eV/ion. At a discharge propellant-utilization efficiency of 95 percent, the beam-ion production cost was reduced to about 155 eV/ion, representing a reduction of about 40 eV/ion over the corresponding value for the 30 cm diameter J-series thruster. Comprehensive Langmuir-probe surveys were obtained and compared with similar measurements for a J-series thruster. A successful volume-averaging scheme was developed to correlate thruster performance with the dominant plasma processes that prevail in the two thruster designs. The average Maxwellian electron temperature in the optimized ring-cusp design is as much as 1 eV higher than it is in the J-series thruster. Advances in ion-extraction electrode fabrication technology were made by improving materials selection criteria, hydroforming and stress-relieving tooling, and fabrications procedures. An ion-extraction performance study was conducted to assess the effect of screen aperture size on ion-optics performance and to verify the effectiveness of a beam-vectoring model for three-grid ion optics. An assessment of the technology readiness of the J-series thruster was completed, and operation of an 8 cm IAPS thruster using a simplified power processor was demonstrated.

Beattie, J. R.↗
NASA NTRS1990

Lead-ruthenium pyrochlores as oxygen electrocatalysts

An investigation of lead-ruthenium pyrochlores of the structure Pb2(Ru/2-x/Pb/x/) O7-y for use as oxygen electrocatalysts in alkaline media is discussed. Lead-ruthenium pyrochlore mixed metal oxides were prepared and characterized by X-ray diffraction, BET surface area, dry powder conductivity, and chemical stability. Gas diffusion electrodes were developed specifically for the lead-ruthenium pyrochlore materials. Also investigated were the effects of varying electrode fabrication parameters on the oxygen reduction performance of the lead-ruthenium pyrochlore electrocatalyst. Long-term stability performance was also evaluated. The oxygen reduction performance of the pyrochlore electrocatalyst is considerably higher than that of the state-of-the-art gold-platinum alloy electrocatalyst currently used by NASA. Furthermore, the pyrochlore electrocatalysts are attractive candidates for high-performance pressurized alkaline fuel cells.

Anderson, E. B.↗
NASA NTRS1991

Progress and recent developments in sodium-metal chloride batteries

Significant strides have been made in the development of high-temperature rechargeable sodium batteries utilizing transition metal chloride cathodes in the last decade, mainly due to the expertise available on Na/S batteries. These systems have already performed attractively in the various feasibility studies and have an excellent safety record. Despite the encouraging figures obtained for specific energies, certain design changes such as modifying the geometry of the beta alumina electrolyte and optimization of the porous cathodes for enhanced electrolyte flow need to be made to achieve high power densities required in applications such as electric vehicles and space. The chemistry of MCl2 cathodes, electrode fabrication, and design options are discussed, and performance data are examined.

Ratnakumar, B. V.↗
NASA NTRS2002

Plasma-enhanced chemical vapor deposition of multiwalled carbon nanofibers

Plasma-enhanced chemical vapor deposition is used to grow vertically aligned multiwalled carbon nanofibers (MWNFs). The graphite basal planes in these nanofibers are not parallel as in nanotubes; instead they exhibit a small angle resembling a stacked cone arrangement. A parametric study with varying process parameters such as growth temperature, feedstock composition, and substrate power has been conducted, and these parameters are found to influence the growth rate, diameter, and morphology. The well-aligned MWNFs are suitable for fabricating electrode systems in sensor and device development.

Nanotechnology/instrumentation/methods↗
DOE OSTI2022

Solvent-Free and Non-Sintered 500 Wh/kg All Solid-State Battery

Navitas teamed up with UMD and ORNL to establish a reliable scientific research team. The project addressed processing limitations of state-of-the-art solid electrolytes by extending solvent-free electrode fabrication technology to the scalable production of cathode/solid electrolyte laminates. The innovation started with a solid-state sulfide electrolyte (LiPS) with Cl stabilization able to meet the keystone conductivity challenge in a film of practical thickness (μ 50 µm). The electrolyte was based on a composite of PTFE, and stabilized LiPSCl. With optimization, the ionic conductivity reached 3.3 ×10 -3 S/cm. The solid electrolyte with as low as 0.4% binder allowed long term cycling (> 500 cycles) of Li/SSE/Li cell at > 4 mA/cm 2 with the utilization of Li > 80%. The Li and SSE interfaces were successfully protected with LiF-rich SEI layer. NCM811cathode active materials were coated with a thin layer of Al 2 O 3 (5 nm). The free standing cathode film was fabricated through dry-process with Al2O3-coated NCM811, LiPSCl, active carbon, and small amount PTFE. The all-solid-state batteries were laminated with free standing surface coated NCM811 cathode film, free standing LiPSCl SSE film, and surface protected Li anode together in a single lamination step, and demonstrated high specific capacity (> 200 mAh/g) with coulombic efficiency > 99.5%. The all-solid-state batteries through solvent-free and no-sintering process are promising for large format cell with 500 Wh/Kg specific energy density.

25 ENERGY STORAGE↗
NASA NTRS1989

Oxygen electrodes for rechargeable alkaline fuel cells

Electrocatalysts and supports for the positive electrode of moderate temperature single-unit rechargeable alkaline fuel cells are being investigated and developed. Candidate support materials were drawn from transition metal carbides, borides, nitrides and oxides which have high conductivity (greater than 1 ohm/cm). Candidate catalyst materials were selected largely from metal oxides of the form ABO sub x (where A = Pb, Cd, Mn, Ti, Zr, La, Sr, Na, and B = Pt, Pd, Ir, Ru, Ni (Co) which were investigated and/or developed for one function only, O2 reduction or O2 evolution. The electrical conductivity requirement for catalysts may be lower, especially if integrated with a higher conductivity support. All candidate materials of acceptable conductivity are subjected to corrosion testing. Materials that survive chemical testing are examined for electrochemical corrosion activity. For more stringent corrosion testing, and for further evaluation of electrocatalysts (which generally show significant O2 evolution at at 1.4 V), samples are held at 1.6 V or 0.6 V for about 100 hours. The surviving materials are then physically and chemically analyzed for signs of degradation. To evaluate the bifunctional oxygen activity of candidate catalysts, Teflon-bonded electrodes are fabricated and tested in a floating electrode configuration. Many of the experimental materials being studied have required development of a customized electrode fabrication procedure. In advanced development, the goal is to reduce the polarization to about 300 to 350 mV. Approximately six support materials and five catalyst materials were identified to date for further development. The test results will be described.

Swette, L.↗