Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Analysis of leading edge and trailing edge cover glass samples before and after treatment with advanced satellite contamination removal techniques

Two samples from Long Duration Exposure Facility (LDEF) experiment M0003-4 were analyzed for molecular and particulate contamination prior to and following treatment with advanced satellite contamination removal techniques (CO2 gas/solid jet spray and oxygen ion beam). The pre- and post-cleaning measurements and analyses are presented. The jet spray removed particulates in seconds. The low energy reactive oxygen ion beam removed 5,000 A of photo polymerized organic hydrocarbon contamination in less than 1 hour. Spectroscopic analytical techniques were applied to the analysis of cleaning efficiency including: Fourier transform infrared, Auger, x ray photoemissions, energy dispersive x ray, and ultraviolet/visible. The results of this work suggest that the contamination studied here was due to spacecraft self-contamination enhanced by atomic oxygen plasma dynamics and solar UV radiation. These results also suggest the efficacy for the jet spray and ion beam contamination control technologies for spacecraft optical surfaces.

Hotaling, S. P.↗
NASA NTRS2006

Variations in the Sea Ice Edge and the Marginal Ice Zone on Different Spatial Scales as Observed from Different Satellite Sensor

The Marginal sea Ice Zone (MIZ) and the sea ice edge are the most dynamic areas of the sea ice cover. Knowledge of the sea ice edge location is vital for routing shipping in the polar regions. The ice edge is the location of recurrent plankton blooms, and is the habitat for a number of animals, including several which are under severe ecological threat. Polar lows are known to preferentially form along the sea ice edge because of induced atmospheric baroclinicity, and the ice edge is also the location of both vertical and horizontal ocean currents driven by thermal and salinity gradients. Finally, sea ice is both a driver and indicator of climate change and monitoring the position of the ice edge accurately over long time periods enables assessment of the impact of global and regional warming near the poles. Several sensors are currently in orbit that can monitor the sea ice edge. These sensors, though, have different spatial resolutions, different limitations, and different repeat frequencies. Satellite passive microwave sensors can monitor the ice edge on a daily or even twice-daily basis, albeit with low spatial resolution - 25 km for the Special Sensor Microwave Imager (SSM/I) or 12.5 km for the Advanced Microwave Scanning Radiometer (AMSR-E). Although special methods exist that allow the detection of the sea ice edge at a quarter of that nominal resolution (PSSM). Visible and infrared data from the Advanced Very High Resolution Radiometer (AVHRR) and from the Moderate Resolution Imaging Spectroradiometer (MODIS) provide daily coverage at 1 km and 250 m, respectively, but the surface observations me limited to cloud-free periods. The Landsat 7 Enhanced Thematic Mapper (ETM+) has a resolution of 15 to 30 m but is limited to cloud-free periods as well, and does not provide daily coverage. Imagery from Synthetic Aperture Radar (SAR) instruments has resolutions of tens of meters to 100 m, and can be used to distinguish open water and sea ice on the basis of surface and volume scattering characteristics. The Canadian RADARSAT C-band SAR provides data that cover the Arctic Ocean and the MIZ every 3 days. A change-point detection approach was utilized to obtain an ice edge estimate from the RADARSAT data The Quickscat scatterometer provides ice edge information with a resolution of a few kilometers on a near-daily basis. During portions of March and April of 2003 a series of aircraft flights were conducted over the ice edge in the Bering Sea carrying the Polarimetric Scanning Radiometer (PSR), which provides spectral coverage identical with the AMSR-E instrument at a resolution of 500 meters. In this study we investigated these different data sets and analyzed differences in their definition of the sea ice edge and the marginal ice zone and how these differences as well as their individual limitations affect the monitoring of the ice edge dynamics. We also examined how the nature of the sea ice edge, including its location, compactness and shape, changes over the seasons. Our approach was based on calculation of distances between ice edges derived from the satellite and aircraft data sets listed above as well as spectral coherence methods and shape parameters such as tortuosity, curvature, and fractional dimension.

Markus, Thorsten↗
NASA NTRS1992

Doppler lidar wind measurement with the edge technique

The edge technique is a new and powerful method for measuring small frequency shifts. Range resolved lidar measurements of winds can be made with high accuracy and high vertical resolution using the edge technique to measure the Doppler shift of an atmospheric backscattered signal from a pulsed laser. The edge technique can be used at near-infrared or visible wavelengths using well developed solid state lasers and detectors with various edge filters. In the edge technique, the laser frequency is located on the steep slope of the spectral response function of a high resolution optical filter. Due to the steep slope of the edge, very small frequency shifts cause large changes in measured signal. The frequency of the outgoing laser pulse is determined by measuring its location on the edge of the filter. This is accomplished by sending a small portion of the beam to the edge detection setup where the incoming light is split into two channels - an edge filter and an energy monitor channel. The energy monitor signal is used to normalize the edge filter signal for magnitude. The laser return backscattered from the atmosphere is collected by a telescope and directed through the edge detection setup to determine its frequency (location on the edge) in a similar manner for each range element. The Doppler shift, and thus the wind, is determined from a differential measurement of the frequency of the outgoing laser pulse and the frequency of the laser return backscattered from the atmosphere. We have conducted simulations of the performance of an edge lidar system using an injection seeded pulsed Nd:YAG laser at 1.06 microns. The central fringe of a Fabry-Perot etalon is used as a high resolution edge filter to measure the shift of the aerosol return.

Korb, C. Laurence↗
NASA NTRS1999

Edge-Flames in Von Karman Swirling Flows

Classical understanding of diffusion flames dictates that they, unlike the premixed flames, do not possess a characteristic propagation velocity and are constrained by stoichiometric requirements at the flame surface. However, it has been commonly observed that when local extinction occurs within a diffusion flame sheet, the edges that are formed propagate with distinct speeds. In general, the propagation speed of these edges depend on their geometrical shape (concave, convex, or straight) among other factors. Recently, Buckmaster investigated the dynamics of straight diffusion flame edges separating burning and quenched regions using simplified one-dimensional models. He showed that these flame edges can have positive, negative, or zero velocity depending on the Damkoehler number of the equilibrium diffusion flame that support them. It was also shown that this unsteady flame-edge behavior is intrinsically linked to S-curve behavior of the diffusion flame with varying Damkoehler number. When the system Damkoehler number lies between the extinction and ignition limits, flame edges can propagate as an "ignition wave" or as a "failure wave," and for a critical Damkoehler number remain as a stationary flame-edge. We have extend Buckmaster's 1-d model to more general edge-flame configurations where the edges appear as "flame holes" or as "flame disks". These two configurations along with the straight-edge case cover the entire range of possible edge-flame geometry observable in planar diffusion-flame sheets. A generalized map of edge-flame propagation velocities as a function of the system Damkoehler number and the edge-flame radius is presented. Experimentally we show that edge flames can be created using diffusion flames embedded in von Karman boundary layers. In a von Karman boundary layer, the flow is generated by spinning a solid (fuel) disk in a quiescent ambient gas. Under normal gravity we were able to produce "flame disks" over a range of fuel-disk rotational velocities varying from 0 to 20 revolutions per second, by orienting the burning surface of the fuel disk facing downward.

Nayagam, Vedha↗
NASA NTRS1972

Effect of trailing edge geometry and thickness on the performance of certain turbine stator blading

The experimental and analytical investigation included solid blades with five different trailing-edge thicknesses and four different trailing-edge geometries. One of the geometries was round, one was square, one was tapered from the suction surface, and the other tapered from the pressure surface. One of the trailing-edge thicknesses was sharp edged; the other four thicknesses were equivalent to about 5, 11, 16, and 20 percent of the blade throat width. The experimental results show increased efficiency loss for increased trailing-edge thickness for all trailing-edge geometries. The blade with round trailing edge, equal to about 11 percent of the blade throat width, had 60 percent more loss than the sharp-edged blade. For the same trailing-edge thickness, square trailing edges caused more loss than round trailing edges, and the tapered trailing edges caused about the same loss as the round trailing edges.

Prust, H. W., Jr.↗