Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drag reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Combustion in the Wake as a Means of Body-Drag Reduction as Determined from Free-Flight Tests of 40-Millimeter Shells

The results of free-flight drag tests of 40-millimeter shells conducted by the National Advisory Committee for Aeronautics for the Ballistic Research Laboratories, Ordnance Department, U. S. Army, are presented. A drag reduction at supersonic speeds of approximately 20 percent of the projectile's drag was obtained by combustion in the wake of the projectile in flight.

Welsh, Clement J.↗
NASA NTRS2003

Investigation of an Oscillating Surface Plasma for Turbulent Drag Reduction

An oscillating, weakly ionized surface plasma has been investigated for use in turbulent boundary layer viscous drag reduction. The study was based on reports showing that mechanical spanwise oscillations of a wall can reduce viscous drag due to a turbulent boundary layer by up to 40%. It was hypothesized that the plasma induced body force in high electric field gradients of a surface plasma along strip electrodes could also be configured to oscillate the flow. Thin dielectric panels with millimeter-scale, flush- mounted, triad electrode arrays with one and two-phase high voltage excitation were tested. Results showed that while a small oscillation could be obtained, the effect was lost at a low frequency (less than 100Hz). Furthermore, a mean flow was generated during the oscillation that complicates the effect. Hot-wire and pitot probe diagnostics are presented along with phase-averaged images revealing plasma structure.

Wilkinson, Stephen P.↗
NASA NTRS1984

Porosity effect on supercritical airfoil drag reduction by shock wave/boundary layer control

An investigation of the passive shock wave/boundary layer control for reducing the drag of 14 percent-thick supercritical airfoil was conducted in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel at transonic Mach numbers. Various porous surfaces with a cavity beneath it was positioned on the area of the airfoil, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a uniform porosity surface the normal shock wave for solid surface was changed to a lambda shock wave, and the wake impact pressure data indicated an appreciable drag reduction at transonic Mach numbers. For a free stream Mach number of 0.81 the profile drag coefficient for the airfoil top surface with uniform porosity was 46 percent lower than for the solid surface airfoil.

Nagamatsu, H. T.↗
NASA NTRS1975

Evaluation of viscous drag reduction schemes for subsonic transports

The results are described of a theoretical study of viscous drag reduction schemes for potential application to the fuselage of a long-haul subsonic transport aircraft. The schemes which were examined included tangential slot injection on the fuselage and various synergetic combinations of tangential slot injection and distributed suction applied to wing and fuselage surfaces. Both passive and mechanical (utilizing turbo-machinery) systems were examined. Overall performance of the selected systems was determined at a fixed subsonic cruise condition corresponding to a flight Mach number of free stream M = 0.8 and an altitude of 11,000 m. The nominal aircraft to which most of the performance data was referenced was a wide-body transport of the Boeing 747 category. Some of the performance results obtained with wing suction are referenced to a Lockheed C-141 Star Lifter wing section. Alternate designs investigated involved combinations of boundary layer suction on the wing surfaces and injection on the fuselage, and suction and injection combinations applied to the fuselage only.

Marino, A.↗
NASA NTRS1987

Drag reduction on a bluff body at yaw angles to 30 degrees

The base separation alleviation and drag reduction effectiveness of transverse rectangular grooves and longitudinal v-grooves in the afterbody shoulder region of a bluff body is investigated for body yaw angles of 0-30 deg. The grooves are found to be beneficial in reducing both freestream and axial drag coefficients at yaw angles of up to 25 deg.

Howard, Floyd G.↗
NASA NTRS1985

Airfoil large-eddy breakup devices for turbulent drag reduction

Large-eddy breakup devices were tested in a turbulent boundary layer at a momentum thickness Reynolds number of 7400. The drag reducing characteristics of thin, tapered plates, NACA 0009, and NACA 4409 airfoil shapes were determined and compared with lower Reynolds number data obtained with thin elements. The results indicate that at the higher Reynolds numbers of the present tests the thin, tapered plates in a tandem arrangement produced large downstream skin-friction reductions (maximum 0/40 percent/), and gave net drag reductions at least as large as for lower Reynolds numbers. Tandem NACA 0009 airfoils, which were approximately 10 times thicker than the thin plates, gave similar results with a maximum downstream skin-friction reduction of 0(30 percent) and a net drag reduction of 7 percent. The device drag for this shape was determined to be near laminar skin friction. The NACA 4409 airfoils suffered large regions of separated flow and produced no net drag reduction.

Anders, J. B.↗
NASA NTRS1986

Overview of the Langley viscous drag reduction program

As a result of reductions in form drag and roughness drag, skin friction, drag, or viscous drag now represents a major contributor to the cruise drag of subsonic business and transport aircraft, and hence, is considered a barrier problem to further significant improvements in the aerodynamic efficiency of these aircraft. To meet the challenge, research in the areas of laminar-flow control and turbulence control/drag reduction was initiated at NASA Langley Research Center. The significance of this research is discussed.

Hefner, Jerry N.↗
NASA NTRS2003

Aerodynamic Drag and Drag Reduction: Energy and Energy Savings (Invited)

An assessment of the role of fluid dynamic resistance and/or aerodynamic drag and the relationship to energy use in the United States is presented. Existing data indicates that up to 25% of the total energy consumed in the United States is used to overcome aerodynamic drag, 27% of the total energy used in the United States is consumed by transportation systems, and 60% of the transportation energy or 16% of the total energy consumed in the United States is used to overcome aerodynamic drag in transportation systems. Drag reduction goals of 50% are proposed and discussed which if realized would produce a 7.85% total energy savings. This energy savings correlates to a yearly cost savings in the $30Billion dollar range.

Wood, Richard M.↗
NASA NTRS2003

Aerodynamic Drag and Drag Reduction: Energy and Energy Savings (Invited)

An assessment of the role of fluid dynamic resistance and/or aerodynamic drag and the relationship to energy use in the United States is presented. Existing data indicates that up to 25% of the total energy consumed in the United States is used to overcome aerodynamic drag, 27% of the total energy used in the United States is consumed by transportation systems, and 60% of the transportation energy or 16% of the total energy consumed in the United States is used to overcome aerodynamic drag in transportation systems. Drag reduction goals of 50% are proposed and discussed which if realized would produce a 7.85% total energy savings. This energy savings correlates to a yearly cost savings in the $30Billion dollar range.

Wood, Richard M.↗
NASA NTRS1974

Aerodynamic drag reduction tests on a full-scale tractor-trailer combination with several add-on devices

Aerodynamic drag tests were performed on a conventional cab-over-engine tractor with a 45-foot trailer and five commercially available or potentially available add-on devices using the coast-down method. The tests ranged in velocity from approximately 30 miles per hour to 65 miles per hour and included some flow visualization. A smooth, level runway at Edwards Air Force Base was used for the tests, and deceleration measurements were taken with both accelerometers and stopwatches. An evaluation of the drag reduction results obtained with each of the five add-on devices is presented.

Montoya, L. C.↗
NASA NTRS2014

Preliminary Assessment of Optimal Longitudinal-Mode Control for Drag Reduction through Distributed Aeroelastic Shaping

The emergence of advanced lightweight materials is resulting in a new generation of lighter, flexible, more-efficient airframes that are enabling concepts for active aeroelastic wing-shape control to achieve greater flight efficiency and increased safety margins. These elastically shaped aircraft concepts require non-traditional methods for large-scale multi-objective flight control that simultaneously seek to gain aerodynamic efficiency in terms of drag reduction while performing traditional command-tracking tasks as part of a complete guidance and navigation solution. This paper presents results from a preliminary study of a notional multi-objective control law for an aeroelastic flexible-wing aircraft controlled through distributed continuous leading and trailing edge control surface actuators. This preliminary study develops and analyzes a multi-objective control law derived from optimal linear quadratic methods on a longitudinal vehicle dynamics model with coupled aeroelastic dynamics. The controller tracks commanded attack-angle while minimizing drag and controlling wing twist and bend. This paper presents an overview of the elastic aircraft concept, outlines the coupled vehicle model, presents the preliminary control law formulation and implementation, presents results from simulation, provides analysis, and concludes by identifying possible future areas for research

aeroelastic↗
NASA NTRS1975

Drag Reduction: Back to Basics

Aeronautical design engineering for general aviation aircraft considers the iteration of wind tunnel test data are lift, weight, drag, and thrust as the basic balancing factor in drag reduction efforts.

Nicks, O. W.↗
NASA NTRS2011

Intelligent Control for Drag Reduction on the X-48B Vehicle

This paper focuses on the development of an intelligent control technology for in-flight drag reduction. The system is integrated with and demonstrated on the full X-48B nonlinear simulation. The intelligent control system utilizes a peak-seeking control method implemented with a time-varying Kalman filter. Performance functional coordinate and magnitude measurements, or independent and dependent parameters respectively, are used by the Kalman filter to provide the system with gradient estimates of the designed performance function which is used to drive the system toward a local minimum in a steepestdescent approach. To ensure ease of integration and algorithm performance, a single-input single-output approach was chosen. The framework, specific implementation considerations, simulation results, and flight feasibility issues related to this platform are discussed.

Griffin, Brian Joseph↗
NASA NTRS1985

Axisymmetric bluff-body drag reduction through geometrical modification

The effect of shoulder radiusing and grooving (longitudinally and circumferentially) the afterbodies of bluff bodies to reduce the base drag at low speeds is investigated experimentally. Shoulder radii as large as 2.75 body diameters are examined. Reynolds number (ReD) based on body diameter varied from 20,000 to 200,000. Results indicate that increasing the shoulder radius to 2.00 body diameters can reduce the drag levels to those of a streamline body having 67 percent greater fineness ratio. For the relatively sharp shoulder case, body drag reductions as large as 50 and 33 percent are obtained using circumferential or longitudinal grooves, respectively.

Howard, F. G.↗