Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “disconnection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Passive Orbital Disconnect Strut (PODS 3), structural and thermal test program

A test program is undertaken to verify that the lifetime of a shuttle launchable dewar can be increased by using passive orbital disconnect struts (PODS). A detailed design is performed on the cold end (PODS-III) portion of the strut. Structural analysis of the thin-wall fiberglass tube allows selection of the optimum winding angle and tube dimensions. Structural tests on the thin-wall fiberglass tube measure both the tension and compression modulus at ambient and LN2 temperatures, the radial deflection versus side load, and the ultimate compression strength of the tube at LN2 temperature. The thermal expansion of the fiberglass tube plus Invar is also measured down to 78 K. The axial gap at the wedge portion of the stem is set based on these data. The PODS-III test article parts are fabricated and assembled using a detailed assembly procedure. The thermal conductants in the orbital configuration was measured for body temperatures between 5 and 40 K. This temperature range covers the predicted ground hold and orbit temperatures for vapor-cooled supports. The test results are then compared with heat leak values predicted before the test began. Side load, axial compression load, and tension load tests conclude the test program.

Parmley, R. T.↗
NASA NTRS1983

Possible observation of a disconnected magnetic structure in a coronal transient

Solar Maximum Mission coronagraph/polarimeter observations of the coronal transient of March 15-16, 1980, which show a bright front convex toward the sun propagating out through the corona at 175 km/sec, are reported. A fan-shaped bright region connecting this front to the inner corona collapses into a narrow, bright ray over the next few hours. These observations are interpreted as resulting from the disconnection of magnetic loops from the underlying prominencelike loop structures seen rising earlier in the event. Other similar inverted arches exist in the C/P data, but are usually seen with poorer temporal resolution.

Illing, R. M. E.↗
NASA NTRS1985

Passive Orbital Disconnect Strut (PODS 3) structural test program

A passive orbital disconnect strut (PODS-3) was analyzed structurally and thermally. Development tests on a graphite/epoxy orbit tube and S glass epoxy launch tube provided the needed data to finalize the design. A detailed assembly procedure was prepared. One strut was fabricated. Shorting loads in both the axial and lateral direction (vs. load angle and location) were measured. The strut was taken to design limit loads at both ambient and 78 K (cold end only). One million fatigue cycles were performed at predicted STS loads (half in tension, half in compression) with the cold end at 78 K. The fatigue test was repeated at design limit loads. Six struts were then fabricated and tested as a system. Axial loads, side loads, and simulated asymmetric loads due to temperature gradients around the vacuum shell were applied. Shorting loads were measured for all tests.

Parmley, R. T.↗
NASA NTRS1985

Test and evaluate passive orbital disconnect struts (PODS 3)

The objectives of the Passive Orbital Disconnect Struts (PODS) test are to evaluate modal resonance of the PODS-III supports to obtain engineering data required for use of PODS-III on flight systems; determine possible performance improvements in large LO2/LH2 space applications. (1) Modal Vibration Tests. A modal resonance survey is performed on a set of six PODS-III struts assembled in a dewar simulator. The survey conditions simulate both launch and orbital loadings of the struts. The orbital load range spans a full to an empty tank. The frequencies surveyed cover the range consistent with Shuttle qualification requirements and the principal resonant modes of the strut system. (2) Benefit study. The benefit of using PODS-III supports on OTV and Space Station LO sub 2 and LH sub 2 reference tanks was compared to nondisconnect supports. Four LO sub 2 and LH sub 2 tanks were studied under various conditions: (1) holding the launch resonance at 35 Hz and varying the orbit resonance; (2) analyzing both full and emtpy tanks at launch; (3) varying orbit boundary temperaure; (4) varying the number of struts; (5) varying orbit times; and (6) using or not using vapor cooling.

Parmley, R. T.↗
NASA NTRS1988

Design and test of a modified passive orbital disconnect strut (PODS-IV)

The design and testing of a modification to the Passive Orbital Disconnect Struts (PODS) III system (designed to reduce support conductance and superfluid-helium-tank dewar weights), PODS IV, are discussed. The PODS IV design was found to achieve a nominal increase of 630-812 percent in side-load resistance over the PODS-III design, with a predicted 15-percent increase in thermal conductance. It is noted that the increase in side-load resistance largely removes the limitation on length of the orbit tube inherent in the PODS III design. The higher resistance of the longer orbit tube results in lower total conductance for the PODS-IV design.

Spradley, Iran E.↗
NASA NTRS1991

Three-Dimensional Navier-Stokes Simulation of Space Shuttle Main Propulsion 17-inch Disconnect Valves

A steady incompressible three-dimensional viscous flow analysis has been conducted for the Space Shuttle external tank/orbiter propellant feed line disconnect flapper valves with upstream elbows. The Navier-Stokes code, INS3D, is modified to handle interior obstacles and a simple turbulence model. The flow solver is tested for stability and convergence in the presence of interior flappers. An under-relaxation scheme has been incorporated to improve the solution stability. Important flow characteristics such as secondary flows, recirculation, vortex and wake regions, and separated flows are observed. Computed values for forces, moments, and pressure drop are in satisfactory agreement with water flow test data covering a maximum tube Reynolds number of 3.5 million. The predicted hydrodynamical stability of the flappers correlates well with the measurements.

Kandula, M.↗
NASA NTRS1991

The last disconnection events in Comet Halley in April 1986

Disconnection event (DE) in cometary plasma physics is the regular loss of the entire plasma tail and the growth of the new one. Analysis of a sequence of DEs that occurred 13-18 April, 1986 shows that they correlate well with a magnetic, sector-boundary crossing and a complex magnetic structure in the solar wind with polarity reversals that occurred about one day later. These events are entirely consistent with sunward, magnetic reconnection as the DE mechanism.

Brandt, John C.↗
NASA NTRS1992

Simulations of coronal disconnection events

The lack of evidence for magnetic disconnection of coronal mass ejections (CMEs) from the sun has long been a puzzle, as it implies a buildup of the interplanetary magnetic field (IMF) magnitude over time. Such a buildup is ruled out by observations. Magnetic reconnection above helmet streamer configurations could provide a mechanism for maintaining the observed relative constancy of the IMF (McComas et al., 1989). McComas et al. (1991) showed observational evidence of reconnection above a streamer. This interpretation is investigated using time-dependent MHD simulations. The opening of new magnetic flux on the sun (as might occur in a CME or other transient event) is modeled as an increase in magnetic flux at the poles of a simulated corona. It is found that this perturbation can in fact cause reconnection above an equatorial helmet streamer, and the resultant density signature is similar to the observations of McComas et al. (1991).

Linker, Jon A.↗
NASA NTRS1992

The disconnection event of 16.0 March 1986 in comet Halley

From kinematic extrapolation of tail/nucleus distance measurements on photographic images in the International Halley Watch (IHW) archive, we calculated the disconnection time of the 16-19 March 1986 event to be 16.0 (plus or minus 0.1) March. The solar wind conditions around Comet Halley at the time of the DE, inferred by corotation of IMP-8 satellite data to the comet, were such that (1) Comet Halley had just crossed the interplanetary magnetic field (IMF) sector boundary; (2) the solar wind density was approximately 8 cm(exp -3); (3) the solar wind speed was approximately 600 km/sec; (4) the IMF magnitude was approximately 8 nT. Given these conditions, we conclude that the most likely cause of the 16.0 March DE was front-side magnetic reconnection, as described in the model of Niedner and Brandt (1978).

Randall, Cora E.↗
NASA NTRS1995

Quick-Connect, Slow-Disconnect Nut

Proposed quick-connect, slow-disconnect nut installs simply by pushing it onto standard bolt or threaded stud. Once installed, removed only by unscrewing it in manner of conventional nut.

Weddendorf, Bruce↗
NASA NTRS1995

Quick-Connect, Slow-Disconnect Bolt

Proposed bolt functions similarly to device described in article "Quick-Connect, Slow-Disconnect Nut" (MFS-28833). Bolt installed in standard threaded hole simply by pushing it into hole. Once inserted, bolt withdrawn only by turning it in conventional way.

Weddendorf, Bruce↗
NASA NTRS1995

Open and disconnected magnetic field lines within coronal mass ejections in the solar wind: Evidence for 3-dimensional reconnection

Measurements of suprathermal electron fluxes in the solar wind at energies greater than approximatley 80 eV indicate that magnetic field lines within coronal mass ejections. CMEs, near and beyond 1 AU are normally connected to the Sun at both ends. However, a preliminary reexamination of events previously identified as CMEs in the ISEE 3 data reveals that about 1/4 of all such events contain limited regions where field lines appear to be either connected to the Sun at only one end or connected to the outer heliosphere at both ends. Similar intervals of open and disconnected field lines within CMEs have been identified in the Ulysses observations. We believe that these anomalous field topologies within CMEs are most naturally interpreted in terms of 3-dimensional reconnection behind CMEs close to the Sun. Such reconnection also provides a natural explanation both for the flux rope topology of many CMEs as well as the coronal loops formed during long-duration solar soft X ray events. Although detailed numerical simulations of 3-dimensional reconnection behind CMEs are not yet available, such simulations have been done for the qualitatively similar geometry that prevails within the geomagnetic tail. Those simulations of plasmoid formation in the geomagnetic tail do produce the mixture of field topologies within plasmoids discussed here for CMEs.

Gosling, J. T.↗
NASA NTRS2001

Improved Quick Disconnect (QD) Interface Through Fail Safe Parts Identification

An extensive review of existing Quick Disconnects (QDs) mating and demating operations was performed to determine which shuttle part interface identifications and procedures contribute to human factor errors. The research methods used consisted of interviews with engineers and technicians, examination of incident reports, critiques of video and audio tapes of QD operations, and attendance of a Hyper QD operational course. The data strongly suggests that there are inherit human factor errors involved in QD operations. To promote fail-safe operations, QD interface problem areas and recommendations were outlined and reviewed. It is suggested that dialogue, investigations and recommendations continue.

Blanch-Payne, Evelyn↗
NASA NTRS2004

International Space Station (ISS) Low Pressure Intramodule Quick Disconnect Failures

A failure of an ISS intermodule Quick Disconnect (QD) during protoflight vibration testing of ISS regenerative Environmental Control and Life Support (ECLS) hardware led to the discovery of QD design, manufacturing, and test flaws which can yield the male QD susceptible to failure of the secondary housing seal and inadequate housing assembly locking mechanisms. Discovery of this failure had large implications when considering that currently there are 399 similar units on orbit and approximately 1100 units on the ground integrated into flight hardware. Discovery of the nature of the failure required testing and analysis and implementation of a recovery plan requiring part screening and review of element level and project hazard analysis to determine if secondary seals are required. Implementation also involves coordination with the Nodes and MPLM project offices, Regenerative ECLS Project, ISS Payloads, JAXA, ESA, and ISS Logistics and Maintenance.

Lewis, John F.↗
NASA NTRS2006

Fluid Quick Disconnects - ISS Lessons Learned

The International Space Station has many fluid systems on the United States On-orbit Segment supporting thermal control, life support, extravehicular activities and payloads. To facilitate assembly and maintenance, fluid quick disconnect (QD) fittings are used throughout these systems for both internal pressurized modules and for external systems exposed to space. In the years since full scale development began on these QDs, a number of design and performance issues have surfaced and required substantial program funds and activity to rectify. This paper is intended to describe the most significant of these issues, their resolutions, and the lessons learned from the ISS experience.

Bond, Timothy A.↗
NASA NTRS2007

Questions Concerning the Disconnection and Eruption of Filaments and CMEs

Reviews examples of eruptions and failed eruptions of filaments and CMEs and review questions concerning the processes and mechanisms involved. Where and how does disconnection occur? What can we learn (if anything!) about CME eruptions by observing related filament eruptions?

Kucera, Theresa↗
NASA NTRS2010

High flow, low mobile weight quick disconnect system

A fluid coupling device and coupling system that may start and stop the flow of a fluid is disclosed. In some embodiments, first and second couplings are provided having an actuator coupled with each of the couplings. The couplings and actuators may be detachable to provide quick disconnect features and, in some embodiments, provide unitary actuation for the actuators of the coupling device to facilitate connection in mobile applications. Actuation may occur as the two couplings and actuators are engaged and disengaged and may occur by rotational actuation of the actuators. Rotational actuation can be provided to ensure flow through the coupling device, which in some embodiments may further provide an offset venturi feature. Upon disengagement, a compression element such as a compression spring can be provided to return the actuators to a closed position. Some embodiments further provide a seal external to the actuators and provided at incipient engagement of the couplings.

Smith, Ronn G.↗