Results for “difference frequency” — Page 5

DOE OSTI2023

Triply-resonant sum frequency conversion with gallium phosphide ring resonators

We demonstrate quasi-phase matched, triply-resonant sum frequency conversion in 10.6-µm-diameter integrated gallium phosphide ring resonators. A small-signal, waveguide-to-waveguide power conversion efficiency of 8 ± 1.1%/mW; is measured for conversion from telecom (1536 nm) and near infrared (1117 nm) to visible (647 nm) wavelengths with an absolute power conversion efficiency of 6.3 ± 0.6%; measured at saturation pump power. For the complementary difference frequency generation process, a single photon conversion efficiency of 7.2%/mW from visible to telecom is projected for resonators with optimized coupling. Efficient conversion from visible to telecom will facilitate long-distance transmission of spin-entangled photons from solid-state emitters such as the diamond NV center, allowing long-distance entanglement for quantum networks.

42 ENGINEERING↗

DOE OSTI2024

Tunable Inductive Coupler for High-Fidelity Gates Between Fluxonium Qubits

The fluxonium qubit is a promising candidate for quantum computation due to its long coherence times and large anharmonicity. We present a tunable coupler that realizes strong inductive coupling between two heavy-fluxonium qubits, each with approximately 50-MHz frequencies and approximately 5-GHz anharmonicities. The coupler enables the qubits to have a large tuning range of 𝑋⁢𝑋 coupling strengths (−35 to 75 MHz). The 𝑍⁢𝑍 coupling strength is <3 kHz across the entire coupler bias range and <100 Hz at the coupler off position. These qualities lead to fast high-fidelity single- and two-qubit gates. By driving at the difference frequency of the two qubits, we realize a $\sqrt{i\textrm{SWAP}}$ gate in 258 ns with fidelity 99.72%, and by driving at the sum frequency of the two qubits, we achieve a $\sqrt{𝑏⁢\textrm{SWAP}}$ gate in 102 ns with fidelity 99.91%. This latter gate is only five qubit Larmor periods in length. We run cross-entropy benchmarking for over 20 consecutive hours and measure stable gate fidelities, with $\sqrt{𝑏⁢\textrm{SWAP}}$ drift (2⁢𝜎) <0.02% and $\sqrt{i\textrm{SWAP}}$ drift <0.08%.

Zhang, Helin↗

DOE OSTI2026

Calibration and Data Analysis of a Frequency Selectable Laser Source for CMB Detector Characterization

Cosmic Microwave Background (CMB) experiments study faint radiation left over from the early universe. The CMB was created when the universe became cool enough for light to travel freely through space, and today it gives scientists one of the earliest images of the universe. One important goal of modern CMB experiments is to measure this radiation with higher precision in order to search for evidence that supports the theory of cosmic inflation. To do this, scientists use extremely sensitive detectors that must be calibrated accurately. The Frequency Selectable Laser Source, or FLS, is a new calibration tool that can send selected frequencies to detectors and help measure their response. During my internship, I worked on the FLS after it returned to Fermilab from Chile, where it had been used to characterize detectors at the Simons Observatory. The system came back in parts, so the first part of my project was helping rebuild the optical and mechanical setup. After the system was rebuilt, we performed alignments to maximize the receiver photocurrent. We then collected calibration measurements over different frequency ranges, including 543 GHz to 568 GHz, 740 GHz to 766 GHz, and 60 GHz to 500 GHz. These measurements were used to check waterline calibration and reflectivity features and compare new data with previous data. Another major part of my project was learning Python so I could understand previous analysis code, modify it for new files, and write my own code to compare the mean response between datasets. The results showed that the new data was close to previous measurements and that waterline features near 556 GHz and 752 GHz were found within less than 1.5 GHz of the expected values. I also completed the reflectivity analysis for five prisms in two polarization orientations. In the original orientation, the results were consistent between the five prisms and close to values measured on a different system at the University of Chicago. I then collected a second set of measurements on my own with the polarization of the laser rotated by 90 degrees and compared them with the original data using the same Python workflow. The measured reflectivity increased for all five prisms in the new orientation, showing that the prism reflectivity depends on polarization. Future work will focus on using the FLS to characterize real CMB detectors.

Pumarino, Rafael [Unlisted]↗

DOE OSTI2026

Calibration and Data Analysis of a Frequency Selectable Laser Source for CMB Detector Characterization

Cosmic Microwave Background (CMB) experiments study faint radiation left over from the early universe. The CMB was created when the universe became cool enough for light to travel freely through space, and today it gives scientists one of the earliest images of the universe. One important goal of modern CMB experiments is to measure this radiation with higher precision in order to search for evidence that supports the theory of cosmic inflation. To do this, scientists use extremely sensitive detectors that must be calibrated accurately. The Frequency Selectable Laser Source, or FLS, is a new calibration tool that can send selected frequencies to detectors and help measure their response. During my internship, I worked on the FLS after it returned to Fermilab from Chile, where it had been used to characterize detectors at the Simons Observatory. The system came back in parts, so the first part of my project was helping rebuild the optical and mechanical setup. After the system was rebuilt, we performed alignments to maximize the receiver photocurrent. We then collected calibration measurements over different frequency ranges, including 543 GHz to 568 GHz, 740 GHz to 766 GHz, and 60 GHz to 500 GHz. These measurements were used to check waterline calibration and reflectivity features and compare new data with previous data. Another major part of my project was learning Python so I could understand previous analysis code, modify it for new files, and write my own code to compare the mean response between datasets. The results showed that the new data was close to previous measurements and that waterline features near 556 GHz and 752 GHz were found within less than 1.5 GHz of the expected values. I also completed the reflectivity analysis for five prisms in two polarization orientations. In the original orientation, the results were consistent between the five prisms and close to values measured on a different system at the University of Chicago. I then collected a second set of measurements on my own with the polarization of the laser rotated by 90 degrees and compared them with the original data using the same Python workflow. The measured reflectivity increased for all five prisms in the new orientation, showing that the prism reflectivity depends on polarization. Future work will focus on using the FLS to characterize real CMB detectors.

Pumarino Meza, Rafael [Unlisted, US; Fermilab]↗

DOE OSTI2026

Calibration and Data Analysis of a Frequency Selectable Laser Source for CMB Detector Characterization

Cosmic Microwave Background (CMB) experiments study faint radiation left over from the early universe. The CMB was created when the universe became cool enough for light to travel freely through space, and today it gives scientists one of the earliest images of the universe. One important goal of modern CMB experiments is to measure this radiation with higher precision in order to search for evidence that supports the theory of cosmic inflation. To do this, scientists use extremely sensitive detectors that must be calibrated accurately. The Frequency Selectable Laser Source, or FLS, is a new calibration tool that can send selected frequencies to detectors and help measure their response. During my internship, I worked on the FLS after it returned to Fermilab from Chile, where it had been used to characterize detectors at the Simons Observatory. The system came back in parts, so the first part of my project was helping rebuild the optical and mechanical setup. After the system was rebuilt, we performed alignments to maximize the receiver photocurrent. We then collected calibration measurements over different frequency ranges, including 543 GHz to 568 GHz, 740 GHz to 766 GHz, and 60 GHz to 500 GHz. These measurements were used to check waterline calibration and reflectivity features and compare new data with previous data. Another major part of my project was learning Python so I could understand previous analysis code, modify it for new files, and write my own code to compare the mean response between datasets. The results showed that the new data was close to previous measurements and that waterline features near 556 GHz and 752 GHz were found within less than 1.5 GHz of the expected values. I also completed the reflectivity analysis for five prisms in two polarization orientations. In the original orientation, the results were consistent between the five prisms and close to values measured on a different system at the University of Chicago. I then collected a second set of measurements on my own with the polarization of the laser rotated by 90 degrees and compared them with the original data using the same Python workflow. The measured reflectivity increased for all five prisms in the new orientation, showing that the prism reflectivity depends on polarization. Future work will focus on using the FLS to characterize real CMB detectors.

Pumarino Meza, Rafael [Unlisted, US; Fermilab]↗

DOE OSTI2020

Comparison of Dead-Time Effects in a WPT System Inverter for Different Fixed-Frequency Modulation Techniques

In this paper, a comparative study of the dead-time effects in a wireless power transfer (WPT) system inverter is performed for different fixed-frequency control techniques. The dead-time is provided between the complementary switching instances of the inverter phase-legs to ensure safe operation of the input power source. Under certain operating conditions, the dead-time results in waveform distortions or voltage-polarity reversal (VPR) at the inverter output. The VPR affects the switching characteristics, harmonic spectrum, switching losses, and output voltage/power of the system. A detailed analysis of the dead-time effect on the WPT system parameters such as output voltage and output power is conducted for the different fixed-frequency control strategies (i.e., traditional phase-shift control, asymmetrical clamped-mode, and asymmetrical duty-cycle control). Furthermore, the impact of dead-time on the inverter switching losses is compared for the different control strategies.

Kavimandan, Utkarsh↗

DOE OSTI2025

Two-Frequency RF Fields Induced Multipactor in Coaxial Transmission Lines

Multipactor is a nonlinear discharge phenomenon that occurs in vacuum RF systems, potentially leading to signal distortion, power loss, and even permanent damage to high-power components. This study presents a detailed investigation of two-surface multipactor in coaxial transmission lines under two-frequency excitation, using one-dimensional (1D) Monte Carlo simulations validated by three-dimensional (3D) Particle-in-Cell (PIC) results and experimental data. Introducing a second carrier mode is shown to suppress multipactor by reshaping and shrinking the susceptibility region, with the extent and location of suppression strongly dependent on the device aspect ratio and the relative phase of the second mode. Distinct suppression patterns emerge across different frequency–gap distance (fd) regimes, and in certain cases, susceptibility expansion is also observed. The study identifies and distinguishes pure and mixed multipactor modes in coaxial geometry, where analytical mode boundaries are not readily defined. Unlike planar systems, pure-mode regions in coaxial structures overlap with mixed-mode domains, complicating classification. Image charge forces are found to have minimal effect on susceptibility thresholds but do influence electron growth rates. These findings provide new insights into waveform-driven control of multipactor in high-power RF systems.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

Seismic Ambient Noise Analyses Reveal Changing Temperature and Water Signals to 10s of Meters Depth in the Critical Zone

The critical zone sustains terrestrial life, but we have few tools to explore it efficiently beyond the first few meters of the subsurface. Using analyses of high-frequency ambient seismic noise from densely spaced seismometers deployed in the forested Shale Hills subcatchment of the Susquehanna Shale Hills Critical Zone Observatory (SSHCZO), we show that temporal changes in seismic velocities at depths from ~1 m to tens of m can be detected. Furthermore, these changes are driven by variations at the land surface. The Moving-Window Cross-Spectral (MWCS) method was employed to measure seismic-velocity changes in coda waves at hourly resolution in 10 different frequency bands. We observed a diurnal signal, a seasonal signal, and a meteorological-event-based signal. These signals were compared to time-series measurements of precipitation, well water levels, soil moisture, soil temperature, air temperature, latent heat flux, and air pressure in the heavily instrumented catchment. Most of the velocity changes can be explained by variations in temperature that result in thermoelastic strains that propagate to depth. But some double minima in seismic velocity time-series observed after large rain events were attributed in part to the effects of water infiltration. These results show that high-frequency ambient noise data may in some locations be used to detect changes in the critical zone from ~1 to ~100 m or greater depth with hourly resolution. But interpretation of such data requires multiple environmental data sets to deconvolve the complex interrelationships among thermoelastic and hydrological effects in the subsurface critical zone.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Intensified Soil Moisture Extremes Decrease Soil Organic Carbon Decomposition: A Mechanistic Modeling Analysis

Earth system models have predicted that there will be more frequent and severe precipitation and drought events in terrestrial ecosystems. Microbially mediated decomposition of soil organic carbon (SOC) tends to increase as soils wet and decrease as soils dry. However, the long-term SOC change under intensified moisture extremes remains poorly known as it depends on the frequency and intensity of soil drying and wetting. In this study, we explored long-term SOC dynamics under scenarios of alternating drying-wetting cycles using the Microbial-ENzyme Decomposition model, a mechanistic microbial model. The model was parameterized with 11 years of observations from a temperate deciduous broadleaf forest site, showing satisfactory model performance in both model calibration (R 2 = 0.67) and validation (R 2 = 0.69) against heterotrophic respiration. We then used the model to simulate the long-term SOC dynamics under five scenarios of alternating drying-wetting cycles with different frequencies and severities over a period of 100 years. Results showed that the changes in active microbial biomass C and the corresponding turnover rates of SOC pools were more sensitive to soil drying than soil wetting. As a result, the cumulative soil carbon emission from microbial respiration decreased by 433.7 g C m -2 after the 100-year simulation in the highest frequency and intensity moisture scenario, but was not significantly affected by the lowest frequency and intensity scenario. This study emphasizes the nonlinear response of SOC decomposition to soil moisture changes, which causes decreased decomposition by microbes under drying that is, not compensated by increased decomposition under wetting conditions.

58 GEOSCIENCES↗

DOE OSTI2023

Implementing an electronic sideband offset lock for isotope shift spectroscopy in radium

We demonstrate laser frequency stabilization with at least 6 GHz of offset tunability using an in-phase/quadrature (IQ) modulator to generate electronic sidebands (ESB) on a titanium sapphire laser at 714 nm and we apply this technique to perform isotope shift spectroscopy of 226 Ra and 225 Ra. By locking the laser to a single resonance of a high finesse optical cavity and adjusting the lock offset, we determine the frequency difference between the magneto-optical trap (MOT) transitions in the two isotopes to be 2630.0 ± 0.3 MHz, a factor of 29 more precise than the previously available data. Using the known value of the hyperfine splitting of the 3 P 1 level, we calculate the isotope shift for the 1 S 0 to 3 P 1 transition to be 2267.0 ± 2.2 MHz, a factor of 8 more precise than the best available value. Our technique could be applied to countless other atomic systems to provide unprecedented precision in isotope shift spectroscopy and other relative frequency comparisons.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

How transparent is graphene? A surface science perspective on remote epitaxy

Remote epitaxy is the synthesis of a single crystalline film on a graphene-covered substrate, where the film adopts epitaxial registry to the substrate as if the graphene is transparent. Despite many exciting applications for flexible electronics, strain engineering, and heterogeneous integration, an understanding of the fundamental synthesis mechanisms remains elusive. Here we offer a perspective on the synthesis mechanisms, focusing on the foundational assumption of graphene transparency. We identify challenges for quantifying the strength of the remote substrate potential that permeates through graphene, and propose Fourier and beating analysis as a bias-free method for decomposing the lattice potential contributions from the substrate, from graphene, and from surface reconstructions, each at different frequencies. We highlight the importance of graphene-induced reconstructions on epitaxial templating, drawing comparison to moiré epitaxy. We highlight the role of the remote potential in tuning surface diffusion and adatom kinetics on graphene, which are crucial for navigating the competition between remote epitaxy and defect-seeded mechanisms like pinhole epitaxy. In light of this weak remote potential, we re-evaluate the current state-of-the-art experimental evidence, highlighting why it remains challenging to experimentally validate a ‘remote’ epitaxy mechanism that cannot be explained by alternatives, such as pinhole-seeded epitaxy or serial van der Waals epitaxy. We end with one experimental example that, to out knowledge, cannot be explained by competing mechanisms: a different long-range epitaxial relationship for GdPtSb films grown on graphene/sapphire, compared to direct epitaxy on sapphire. We suggest for future experiments that directly measure the remote potential and impact of tuneable growth kinetics.

epitaxy↗

DOE OSTI2026

DOE EV Data Collection - Vehicle Data

Vehicle data consist of electric vehicle performance data collected directly from the vehicle during standard operations. Data were collected using onboard data loggers that were either installed by the project team or preinstalled by the original equipment manufacturer. Data recorded by the data loggers were made accessible via an online web portal or an application programming interface. Different data loggers were used (HEM, ViriCiti, and Geotab), and the method for each vehicle is defined in the vehicle attributes file. Some systems collected data on a “trip-level” basis, in which each row of a table represents a single trip (the period between a key-on and key-off event), whereas other data were collected on a per-day basis, in which each row represents a single day of operation. Data were collected over a range of data collection periods, depending on the project. Data have been anonymized by removing information or decreasing information resolution as necessary so that fleets are not identifiable. Due to the wide range of vehicle types represented and variation in data collection, data parameters and frequencies differ between vehicles and fleets The **Performance Data Daily/Trip Data Dictionaries** contain definitions for each available parameter associated with a vehicle’s operations, aggregated at either a daily or trip level. The parameters available will vary from vehicle to vehicle, but every possible parameter will be defined. The **Vehicle Attributes Data Dictionary** contains definitions for each available parameter associated with a vehicle’s physical and functional attributes and fleet context. The **Vehicle Attributes** table contains specific vehicle characteristics, coded to an anonymous Vehicle ID. This Vehicle ID can be used as a key between vehicle data and vehicle attribute tables. The **Vehicle Data** tables contain the data from each vehicle’s operations, aggregated at either a daily or trip level, coded to an anonymous Vehicle ID. This Vehicle ID can be used as a key between vehicle data and vehicle attribute tables. Data is being uploaded quarterly through 2023 and subject to change until the conclusion of the project.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Root traits reveal safety and efficiency differences in grasses and shrubs exposed to different fire regimes

Plant roots are important components of terrestrial ecosystems, but little is known about how root traits differ between plant species or vary across space in natural ecosystems. In this study, we investigated how root traits vary across grasses and woody shrubs in a tallgrass prairie located in Manhattan, KS, USA. Specifically, were interested in understanding how anatomical traits vary across these different plant groups, across different depths in the soil, and also across multiple areas of tallgrass prairie that are burned at different frequencies. We compared traits that allow roots to use soil water efficiently and those that help roots persist through extended periods of drought. We found that woody roots exhibited traits that allow them to use water efficiently in shallow soils but persist through drought in deeper soil. Here, these traits may allow shrubs to transport water from shallow soils to deeper soil after large rain events and resist extended periods without rain when soils become dry, which may allow woody plants to successfully compete for water in less frequently burned, more diverse plant communities. Grasses had traits that allow them to use water efficiently but also tolerate drought in shallow soils, regardless of fire treatment. This unique trait combination likely gives grasses a competitive advantage over other tallgrass prairie plants across different fire regimes. Together, these results show that anatomical root traits can be used to enhance mechanistic understanding of plant functioning in dynamic ecosystems.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Harmonic and Subharmonic RF Injection Locking of THz Metasurface Quantum-Cascade VECSEL

Harmonic and subharmonic RF injection locking is demonstrated in a terahertz (THz) quantum-cascade vertical-external-cavity surface-emitting laser (QC-VECSEL). By tuning the RF injection frequency around integer multiples and submultiples of the cavity round-trip frequency, different harmonic and subharmonic orders can be excited in the same device. Modulation-dependent behavior of the device has been studied with recorded lasing spectral broadening and locking bandwidths in each case. In particular, harmonic injection locking results in the observation of harmonic spectra with bandwidths over 200 GHz. A semiclassical Maxwell-density matrix formalism has been applied to interpret QC-VECSEL dynamics, which aligns well with experimental observations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Low-loss millimeter-wave resonators with an improved coupling structure

Millimeter-wave superconducting resonators are a useful tool for studying quantum device coherence in a new frequency domain. However, improving resonators is difficult without a robust and reliable method for coupling millimeter-wave signals to 2D structures. We develop and characterize a tapered transition structure coupling a rectangular waveguide to a planar slotline waveguide with better than 0.5 dB efficiency over 14 GHz, and use it to measure ground-shielded resonators in the W band (75–110 GHz). Having decoupled the resonators from radiative losses, we consistently achieve single-photon quality factors above 10 5 , with a two-level-system loss limit above 10 6 , and verify the effectiveness of oxide removal treatments to reduce loss. These values are 4–5 times higher than those previously reported in the W band, and much closer to typical planar microwave resonators. The improved losses demonstrated by these on-chip millimeter-wave devices shed new light on quantum decoherence in a different frequency regime, offer increased selectivity for high-frequency detectors, and enables new possibilities for hybrid quantum experiments integrating millimeter-wave frequencies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Resonating AdS soliton

The AdS soliton is a nonsingular spacetime that has a flat conformal boundary with a compact S 1 direction. We find a horizonless cohomogeneity-1 metric that describes nonlinear gravitational oscillations of the AdS soliton in five dimensions. We call this spacetime the resonating AdS soliton. This solution is obtained as the nonlinear extension of normal modes of the AdS soliton dual to spin-2 glueball excitations. The boundary energy momentum tensor of the resonating AdS soliton has time periodic components, and it is interpreted as a coherently excited state in the dual field theory. Physical quantities of the resonating AdS soliton are multivalued at a fixed energy, suggesting a transition between different frequency solutions. The energy of the resonating AdS soliton is higher than that of the undeformed AdS soliton, in accordance with the positive energy conjecture proposed by Horowitz and Myers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2024

Rainfall events stimulate episodic associative nitrogen fixation in switchgrass

Abstract Associative N 2 fixation (ANF) is widespread but poorly characterized, limiting our ability to estimate global inputs from N 2 fixation. In some places, ANF rates are at or below detection most of the time but occasionally and unpredictably spiking to very high rates. Here we test the hypothesis that plant phenology and rainfall events stimulate ANF episodes. We measured ANF in intact soil cores in switchgrass ( Panicum virgatum L.) in Michigan, USA. We used rain exclusion shelters to impose three rainfall treatments with each receiving 60 mm of water over a 20-day period but at different frequencies. We concurrently established a treatment that received ambient rainfall, and all four treatments were replicated four times. To assess the effects of plant phenology, we measured ANF at key phenological stages in the ambient treatment. To assess the effects of rainfall, we measured ANF immediately before and immediately after each wetting event in each treatment involving rainfall manipulation. We found that the previous day’s rainfall could explain 29% of the variation in ANF rates within the ambient treatment alone, and that bulk soil C:N ratio was also positively correlated with ANF, explaining 18% of the variation alone. Wetting events increased ANF and the magnitude of response to wetting increased with the amount of water added and decreased with the amount of inorganic N added in water. ANF episodes thus appear to be driven primarily by wetting events. Wetting events likely increase C availability, promote microbial growth, and make rhizosphere conditions conducive to ANF.

Vizza, Carmella (ORCID:0000000292690357)↗

DOE OSTI2023

High-resolution rovibrational spectroscopy of trans -formic acid in the v 1 OH stretching fundamental: Dark state coupling and evidence for charge delocalization dynamics

High-resolution infrared (IR) reduced-Doppler absorption spectra of jet-cooled gas phase trans-formic acid in the v 1 OH stretching fundamental region are reported for the first time, obtained by supersonically expanding trans- formic acid/Ar mixtures through a slit jet nozzle source and rotationally cooling to T rot ≈ 10.9(5) K, with ab- sorption signals recorded by high-resolution difference-frequency IR absorption spectroscopy. Two a/b-type rovibrational bands of comparable intensity, one ~10-fold weaker b-type band, and one ~6-fold weaker a-type band are observed, with vibrational band origins at 3570.493(5), 3566.793(5), 3560.032(9), and 3534.6869(2) cm –1 , respectively. Based on previous Raman jet spectroscopic work by Nejad and Sibert [A. Nejad, E.L. Sibert III, The Raman jet spectrum of trans-formic acid and its deuterated isotopologs: Combining theory and experi- ment to extend the vibrational database, J. Chem. Phys. 154(6) (2021) 064301.], these four rovibrational bands have been assigned to v 1 , (v 2 + v 7 ), (v 6 + 2v 7 + 2v 9 ), and 2v 3 , respectively. Specifically, two of the three upper dark states (2 1 7 1 (a') and 6 1 7 2 9 2 (a')) are close enough to the “bright” 1 1 (a') state to facilitate strong anharmonic resonance interactions, which results in intensity mixing into the two zero-order bands that would otherwise be “dark”. Furthermore, our high-resolution spectral analysis reveals that there are local rotational crossings be- tween these zero-order 1 1 and 2 1 7 1 states resulting in extra lines (i.e., some upper levels in the nominally v 1 band have majority zero-order 2 1 7 1 state character). This motivates development of a 3 coupled state (1 1 , 2 1 7 1 , and 6 1 7 2 9 2 ) picture to aid in the spectral analysis, which is able to match all 3 observed band origins and relative band intensities, as well as indicate the necessity of multistate (> 2) coupling. Though limited by range of J and Ka levels (J’ ≤ 9 and K a ’ ≤ 3) populated at supersonic jet temperatures, this work offers first precision spec- troscopic analysis of trans-formic acid in the v 1 OH stretch region, which should aid in assignment of the more complete yet highly congested room temperature FTIR spectra. Lastly, and in sharp contrast to the spectral complexity in the three predominantly b-type bands, the lone a-type 2v 3 rovibrational band at 3534.6869(2) cm –1 is well described by a simple, rigid asymmetric top Hamiltonian.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗