Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “device fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Oxygen Management to Avoid Photo-Inactive Cd(S,Se) for Efficient Cd(Se,Te) Solar Cells

Our previous work has demonstrated that the formation of a penternary cadmium chalcogenide Cd(O,S,Se,Te) region can significantly reduce the front interface recombination in Cd(Se,Te)-based thin-film solar cells. In this work, we have shown that oxygen management during the device fabrication is crucial to form this region. While both the CdS and CdSe layer depositions and the postdeposition CdCl2 treatment should be conducted in the presence of oxygen, the CdTe deposition should be conducted in an oxygen-free atmosphere. Improper oxygen management leads to low device performance due to the formation of a photoinactive Cd(S,Se) region and reduced absorber quality. Additionally, we investigated the carrier transport and collection properties in devices with photoinactive Cd(S,Se) and photoactive Cd(O,S,Se,Te) at the front interface to gain comprehensive understanding of the mechanisms that resulted in improved efficiencies approaching 20%.

CdTe deposition↗
DOE OSTI2024

Solution-based electrical doping of organic photovoltaics with non-fullerene acceptors facilitated by solvent vapor pre-treatment

Solution-based electrical doping of organic semiconductors using 12-molybdophosphoric acid (PMA) hydrate has been shown to allow p-type doping of conjugated polymers over a limited depth from the surface, enabling the fabrication of organic solar cells with a simplified device architecture. However, the doping level of certain conjugated polymers using PMA was found to be limited by the polymer film volume. Here, we report a modified PMA doping technique based on film volume expansion that is applicable to device fabrication, leading to hole-collecting layer-free non-fullerene organic photovoltaic devices, which exhibit a comparable photovoltaic performance to those with a commonly evaporated MoO3 hole-collecting layer.

Materials Science↗
NASA NTRS1973

Study and design of cryogenic propellant acquisition systems. Volume 2: Supporting experimental program

Areas of cryogenic fuel systems were identified where critical experimental information was needed either to define a design criteria or to establish the feasibility of a design concept or a critical aspect of a particular design. Such data requirements fell into three broad categories: (1) basic surface tension screen characteristics; (2) screen acquisition device fabrication problems; and (3) screen surface tension device operational failure modes. To explore these problems and to establish design criteria where possible, extensive laboratory or bench test scale experiments were conducted. In general, these proved to be quite successful and, in many instances, the test results were directly used in the system design analyses and development. In some cases, particularly those relating to operational-type problems, areas requiring future research were identified, especially screen heat transfer and vibrational effects.

Burge, G. W.↗
NASA NTRS1973

Epitaxial growth of III-V compounds for electroluminescent light sources

The epitaxial growth techniques used in the fabrication of III-V compound electroluminescent devices are reviewed. Both vapor and liquid phase epitaxial techniques are discussed, including the applications of these techniques to well established materials as well as newer materials. The state of the art of light-emitting devices fabricated from members of the III-V compounds and their solid solutions is also reviewed.

Chu, T. L.↗
NASA NTRS1999

Fabrication system, method and apparatus for microelectromechanical devices

A fabrication system and method of fabrication for producing microelectromechanical devices such as field-effect displays using thin-film technology. A spacer is carried at its proximal end on the surface of a substrate having field-effect emitters with the spacer being enabled for tilting movement from a nested position to a deployed position which is orthogonal to the plane of the substrate. An actuator is formed with one end connected with the substrate and another end connected with spacer. The actuator is made of a shape memory alloy material which contracts when heated through the material's phase-change transition temperature. Contraction of the actuator exerts a pulling force on the spacer which is tilted to the deployed position. A plurality of the spacers are distributed over the area of the display. A glass plate having a phosphor-coated surface is fitted over the distal ends of the deployed spacer.

Johnson, A. David↗
DOE OSTI2023

Co-deposition of hole-selective contact and absorber for improving the processability of perovskite solar cells

Simplifying the manufacturing processes of renewable energy technologies is crucial to lowering the barriers to commercialization. In this context, to improve the manufacturability of perovskite solar cells (PSCs), here we have developed a one-step solution-coating procedure in which the hole-selective contact and perovskite light absorber spontaneously form, resulting in efficient inverted PSCs. We observed that phosphonic or carboxylic acids, incorporated into perovskite precursor solutions, self-assemble on the indium tin oxide substrate during perovskite film processing. They form a robust self-assembled monolayer as an excellent hole-selective contact while the perovskite crystallizes. Our approach solves wettability issues and simplifies device fabrication, advancing the manufacturability of PSCs. Our PSC devices with positive-intrinsic-negative (p-i-n) geometry show a power conversion efficiency of 24.5% and retain >90% of their initial efficiency after 1,200 h of operating at the maximum power point under continuous illumination. The approach shows good generality as it is compatible with different self-assembled monolayer molecular systems, perovskites, solvents and processing methods.

14 SOLAR ENERGY↗
NASA NTRS2015

Surface Acoustic Wave Monitor for Deposition and Analysis of Ultra-Thin Films

A surface acoustic wave (SAW) based thin film deposition monitor device and system for monitoring the deposition of ultra-thin films and nanomaterials and the analysis thereof is characterized by acoustic wave device embodiments that include differential delay line device designs, and which can optionally have integral reference devices fabricated on the same substrate as the sensing device, or on a separate device in thermal contact with the film monitoring/analysis device, in order to provide inherently temperature compensated measurements. These deposition monitor and analysis devices can include inherent temperature compensation, higher sensitivity to surface interactions than quartz crystal microbalance (QCM) devices, and the ability to operate at extreme temperatures.

Hines, Jacqueline H.↗
DOE OSTI2022

Facile fabrication of 2D material multilayers and vdW heterostructures with multimodal microscopy and AFM characterization

Reliable transfer processes that enable manipulation of two-dimensional (2D) materials, e.g., transition metal dichalcogenides (TMDCs) and MXenes, from one substrate to another has been a necessity for successful device fabrication. Here, with both mechanical exfoliation and chemical vapor deposition (CVD) widely used, a versatile, clean, deterministic, and yet simple transfer technique is highly needed. To address such need, we developed a transfer method that takes advantage of wettability contrast between interfaces without the use of sacrificial layers or chemical processes. More importantly, a setup was developed to carry out this transfer method with high sample selectivity and fine control of the position and orientation of transferred TMDC crystals, a feature required for fabrication of the devices based on vertical 2D heterostructures. Using both exfoliated and CVD grown materials and subsequent atomic force microscopy (AFM), photoluminescence (PL), confocal Raman and tip enhanced Raman spectroscopy (TERS) characterization, we ascertained the quality of interfaces resulting from the transfer process while preserving excellent 2D material integrity. PL and TERS maps revealed nanometer-scale heterogeneities in the interfaces of fabricated heterostructures, which should enable further perfection of the transfer technique. TERS/TEPL information were employed to identify areas suitable for nanodevice fabrication, making the reported transfer and characterization methods ideal for making high quality assembly of 2D heterostructure more accessible, which should facilitate exploration of vertical 2D heterostructures for applications in electronics, batteries, solar cells, and twistronics.

2D material transfer↗
DOE OSTI2024

Advanced manufacturing provides tailor-made solutions for crystallography with x-ray free-electron lasers

Serial crystallography at large facilities, such as x-ray free-electron lasers and synchrotrons, evolved as a powerful method for the high-resolution structural investigation of proteins that are critical for human health, thus advancing drug discovery and novel therapies. However, a critical barrier to successful serial crystallography experiments lies in the efficient handling of the protein microcrystals and solutions at microscales. Microfluidics are the obvious approach for any high-throughput, nano-to-microliter sample handling, that also requires design flexibility and rapid prototyping to deal with the variable shapes, sizes, and density of crystals. Here, we discuss recent advances in polymer 3D printing for microfluidics-based serial crystallography research and present a demonstration of emerging, large-scale, nano-3D printing approaches leading into the future of 3D sample environment and delivery device fabrication from liquid jet gas-dynamic virtual nozzles devices to fixed-target sample environment technology.

36 MATERIALS SCIENCE↗
NASA NTRS1990

High-temperature electronics

To meet the needs of the aerospace propulsion and space power communities, the high temperature electronics program at the Lewis Research Center is developing silicon carbide (SiC) as a high temperature semiconductor material. This program supports a major element of the Center's mission - to perform basic and developmental research aimed at improving aerospace propulsion systems. Research is focused on developing the crystal growth, characterization, and device fabrication technologies necessary to produce a family of SiC devices.

Matus, Lawrence G.↗
NASA NTRS2012

Next-Generation Microshutter Arrays for Large-Format Imaging and Spectroscopy

A next-generation microshutter array, LArge Microshutter Array (LAMA), was developed as a multi-object field selector. LAMA consists of small-scaled microshutter arrays that can be combined to form large-scale microshutter array mosaics. Microshutter actuation is accomplished via electrostatic attraction between the shutter and a counter electrode, and 2D addressing can be accomplished by applying an electrostatic potential between a row of shutters and a column, orthogonal to the row, of counter electrodes. Microelectromechanical system (MEMS) technology is used to fabricate the microshutter arrays. The main feature of the microshutter device is to use a set of standard surface micromachining processes for device fabrication. Electrostatic actuation is used to eliminate the need for macromechanical magnet actuating components. A simplified electrostatic actuation with no macro components (e.g. moving magnets) required for actuation and latching of the shutters will make the microshutter arrays robust and less prone to mechanical failure. Smaller-size individual arrays will help to increase the yield and thus reduce the cost and improve robustness of the fabrication process. Reducing the size of the individual shutter array to about one square inch and building the large-scale mosaics by tiling these smaller-size arrays would further help to reduce the cost of the device due to the higher yield of smaller devices. The LAMA development is based on prior experience acquired while developing microshutter arrays for the James Webb Space Telescope (JWST), but it will have different features. The LAMA modular design permits large-format mosaicking to cover a field of view at least 50 times larger than JWST MSA. The LAMA electrostatic, instead of magnetic, actuation enables operation cycles at least 100 times faster and a mass significantly smaller compared to JWST MSA. Also, standard surface micromachining technology will simplify the fabrication process, increasing yield and reducing cost.

Moseley, Samuel↗
DOE OSTI2021

Integrating Emerging Polymer Chemistries for the Advancement of Recyclable, Biodegradable, and Biocompatible Electronics

Abstract Through advances in molecular design, understanding of processing parameters, and development of non‐traditional device fabrication techniques, the field of wearable and implantable skin‐inspired devices is rapidly growing interest in the consumer market. Like previous technological advances, economic growth and efficiency is anticipated, as these devices will enable an augmented level of interaction between humans and the environment. However, the parallel growing electronic waste that is yet to be addressed has already left an adverse impact on the environment and human health. Looking forward, it is imperative to develop both human‐ and environmentally‐friendly electronics, which are contingent on emerging recyclable, biodegradable, and biocompatible polymer technologies. This review provides definitions for recyclable, biodegradable, and biocompatible polymers based on reported literature, an overview of the analytical techniques used to characterize mechanical and chemical property changes, and standard policies for real‐life applications. Then, various strategies in designing the next‐generation of polymers to be recyclable, biodegradable, or biocompatible with enhanced functionalities relative to traditional or commercial polymers are discussed. Finally, electronics that exhibit an element of recyclability, biodegradability, or biocompatibility with new molecular design are highlighted with the anticipation of integrating emerging polymer chemistries into future electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1992

Focal plane arrays for submillimeter waves using two-dimensional electron gas elements: A grant under the Innovative Research Program

This final report describes a three-year research effort, aimed at developing new types of THz low noise receivers, based on bulk effect ('hot electron') nonlinearities in the Two-Dimensional Electron Gas (2DEG) Medium, and the inclusion of such receivers in focal plane arrays. 2DEG hot electron mixers have been demonstrated at 35 and 94 GHz with three orders of magnitude wider bandwidth than previous hot electron mixers, which use bulk InSb. The 2DEG mixers employ a new mode of operation, which was invented during this program. Only moderate cooling is required for this mode, to temperatures in the range 20-77 K. Based on the results of this research, it is now possible to design a hot electron mixer focal plane array for the THz range, which is anticipated to have a DSB receiver noise temperature of 500-1000K. In our work on this grant, we have found similar results the the Cronin group (resident at the University of Bath, UK). Neither group has so far demonstrated heterodyne detection in this mode, however. We discovered and explored some new effects in the magnetic field mode, and these are described in the report. In particular, detection of 94 GHz and 238 GHz, respectively, by a new effect, 'Shubnikov de Haas detection', was found to be considerably stronger in our materials than the cyclotron resonance detection. All experiments utilized devices with an active 2DEG region of size of the order of 10-40 micrometers long, and 20-200 micrometers wide, formed at the heterojunction between AlGaAs and GaAs. All device fabrication was performed in-house. The materials for the devices were also grown in-house, utilizing OMCVD (Organo Metallic Chemical Vapor Deposition). In the course of this grant, we developed new techniques for growing AlGaAs/GaAs with mobilities equalling the highest values published by any laboratory. We believe that the field of hot electron mixers and detectors will grow substantially in importance in the next few years, partly as a result of the opportunity given us through this grant, which represents the major effort in the US so far. We note, however, that parallel research on hot electron mixers in thin film superconductors in Russia, and recently in Sweden, have demonstrated mixing up to 1 THz, with the potential for low-noise receivers for frequencies up to many THz. The three groups recently assessed the relative adtantages of 2DEG and superconducting film mixers in a joint paper (Kollberg et al., 1992; see Appendix II).

Yngvesson, K. Sigfrid↗
DOE OSTI2024

Material and Interface Engineering Strategies to Mitigate Decoherence in Superconducting Qubits

While significant strides have been made to increase the coherence time of superconducting qubits, further advancements are essential for realizing scalable quantum computing. Decoherence is often a result of loss and noise stemming from two-level systems and excess quasiparticles, arising due to material defects, fabrication processes, and ambient exposure, particularly at surfaces and interfaces. Our recent efforts to mitigate these decoherence mechanisms have employed a variety of strategies, including low-loss surface encapsulation materials, advanced substrate preparation techniques, modifications to metal film growth, and the development of novel fabrication processes. The structural and chemical properties of materials, surfaces, and interfaces are studied using scanning probe microscopy, electron microscopy, photoelectron spectroscopy, mass spectrometry, and X-ray diffraction, which is correlated to device performance metrics, including superconducting resonator internal quality factor and qubit T1 time. This information is used to identify and understand material sources of loss and their origins in the device fabrication process. Through multi-institution efforts within SQMS we have identified the loss mechanism of interstitial hydrogen in niobium-based devices and shown how standard fabrication processes introduce these hydrides, developing strategies to mitigate their formation.1 Furthermore, we have characterized the metal-substrate interface, including the loss of niobium-silicides formed at that interface, and developed silicon surface treatments that reduce atomic scale roughness and oxygen content at the metal-substrate and Josephson junction interfaces.2-4 By developing the connection between materials properties and the overall performance of superconducting quantum circuitry, we can develop fabrication strategies to mitigate material losses, thus supporting the ongoing efforts to enhance coherence time in superconducting quantum devices. 1. Torres-Castanedo, C. G.*, Goronzy, D. P.*, et al., Adv. Funct. Mater., 2401365 (2024) 2. Lu, X., et al., Phys. Rev. Materials 6, 064402 (2022) 3. Berti, G., Appl. Phys. Lett. 122, 192605 (2023) 4. Kopas, C. J., Goronzy, D. P., et al., arXiv:2408.02863 (2024)

Goronzy, Dominic P.↗
DOE OSTI2026

Demonstration of GaAs-Based Photovoltaics on Acoustically Spalled Surfaces Grown by MOCVD

This study demonstrates the potential of sonic lift-off (SLO) technology for repeatable substrate reuse in gallium arsenide (GaAs)–based photovoltaics (PVs), offering a pathway toward cost effective production for terrestrial PV applications. Single-junction GaAs solar cells fabricated on acoustically spalled substrates achieved performance metrics comparable with those grown on standard commercial substrates, exhibiting short-circuit current densities (J sc ) of approximately 26.2–26.4 mA/cm 2 , open-circuit voltages (V oc ) around 1001 mV, fill factors (FFs) of 84%, and AM1.5G efficiencies near 22%. These results confirm that one reuse cycle can be realized without a performance penalty, offering a direct pathway to reducing substrate cost in fabrication. Furthermore, subsequent reuse of the substrates highlighted critical challenges, as devices fabricated from reused substrates showed significant degradation in performance (J sc of 15.5 mA/cm 2 , V oc of 748 mV, FF of 72%, and efficiency of 8%), primarily due to degradation of the epitaxial structure resulting from repeated spalling cycles.

Acoustic Spalling↗
DOE OSTI2020

Laser-induced digital oxidation for copper-based flexible photodetectors

Copper oxide compounds (Cu x O) with bandgaps of 1.3–2.1 eV (CuO) and 2.1–2.6 eV (Cu 2 O) have been investigated as promising p-type semiconducting materials. Cu x O is generally obtained by deposition or thermal oxidation, but those methods are not optimal for flexible substrates. Furthermore, additional patterning steps are required to fabricate devices. In this work, we present an easy, controllable method to fabricate a metal-semiconductor-metal (MSM) photodetector using laser-induced oxidation of a thin Cu film. After laser irradiation, the Cu film is heated under ambient conditions, and this leads to a thermal oxidation reaction, in which Cu oxide is monolithically formed in the Cu film and a Cu-Cu x O-Cu MSM structure is produced. Since the laser offers localized heating, an arbitrary CuxO pattern can be written in the Cu film by spatially controlled heating. In addition, by optimizing the heating time, the laser-induced oxidation can be successfully performed even on a flexible substrate. To study the laser-induced oxidation, we examined the correlation between laser parameters and the oxidation pattern and analyzed the composition using scanning electron microscopy, Raman spectroscopy, and X-ray photoemission spectroscopy. Furthermore, we measured the transient photoresponse and employed scanning photocurrent microscopy to investigate the mechanism of carrier transport behavior.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Silicon carbide, an emerging high temperature semiconductor

In recent years, the aerospace propulsion and space power communities have expressed a growing need for electronic devices that are capable of sustained high temperature operation. Applications for high temperature electronic devices include development instrumentation within engines, engine control, and condition monitoring systems, and power conditioning and control systems for space platforms and satellites. Other earth-based applications include deep-well drilling instrumentation, nuclear reactor instrumentation and control, and automotive sensors. To meet the needs of these applications, the High Temperature Electronics Program at the Lewis Research Center is developing silicon carbide (SiC) as a high temperature semiconductor material. Research is focussed on developing the crystal growth, characterization, and device fabrication technologies necessary to produce a family of silicon carbide electronic devices and integrated sensors. The progress made in developing silicon carbide is presented, and the challenges that lie ahead are discussed.

Matus, Lawrence G.↗
NASA NTRS1981

Cosmic ray induced errors in I2L microprocessors and logic devices

Large-scale integrated (LSI) devices fabricated with integrated injection logic (I2L) were studied by both heavy ion experiments and device analysis to determine the upset threshold, the charge collection volumes and ultimately the probability for upset in the galactic cosmic ray spectrum. The devices studied, the SEP9900A, the SBP9989 and the P-Code generator were fabricated by Texas Instruments, Inc.

Price, W. E.↗