Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “density correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Jet Mixing and Emission Characteristics of Transverse Jets in Annular and Cylindrical Confined Crossflow

Three dimensional turbulent reacting CFD analyses were performed on transverse jets injected into annular and cylindrical (can) confined crossflows. The goal was to identify and assess mixing differences between annular and can geometries. The approach taken was to optimize both annular and can configurations by systematically varying orifice spacing until lowest emissions were achieved, and then compare the results. Numerical test conditions consisted of a jet-to-mainstream mass-flow ratio of 3.2 and a jet-to-mainstream momentum-flux ratio (J) of 30. The computational results showed that the optimized geometries had similar emission levels at the exit of the mixing section although the annular configuration did mix-out faster. For lowest emissions, the density correlation parameter (C = (S/H) square root of J) was 2.35 for the annular geometry and 3.5 for the can geometry. For the annular geometry, the constant was about twice the value seen for jet mixing at low mass-flow ratios (i.e., MR less than 0.5). For the can geometry, the constant was about 1 1/2 times the value seen for low mass-flow ratios.

Bain, D. B.↗
NASA NTRS2012

The Use of the North Alabama Lightning Mapping Array (NALMA) in the Real-Time Operational Warning Environment During the March 2nd, 2012 Severe Weather Outbreak in Northern Alabama

The North Alabama Lightning Mapping Array (NALMA) is a three-dimensional very high frequency (VHF) detection network consisting of 11 sensors spread across north central Alabama and two sensors located in the Atlanta, Georgia region. The primary advantage of this network is that it detects total lightning, or the combination of both cloud-to-ground and intra-cloud lightning, instead of cloud-to-ground lightning alone. This helps to build a complete picture of storm evolution and development, and can serve as a proxy for storm updraft strength, particularly since intra-cloud lightning makes up the majority of all lightning in a typical thunderstorm. While the NALMA data do not directly indicate severe weather, they can indirectly indicate when a storm is strengthening (weakening) due to increases (decreases) in updraft strength, as the updraft is responsible for charging mechanisms within the storm. Data output are VHF radiation sources, which are produced during lightning breakdown processes. These sources are made into 2x2 km source density grids and are ported into the Advanced Weather Interactive Processing System (AWIPS) for National Weather Service (NWS) offices in Huntsville, AL, Nashville, TN, Morristown, TN, and Birmingham, AL, in near real-time. An increase in sources, or source densities, correlates to increased lightning activity and trends in updraft magnitude as long as the storm is within about 125 km of the center of the LMA network. Operationally, these data have been used at the Huntsville NWS office since early 2003 through a collaborative effort with NASA s Short-term Prediction Research and Transition (SPoRT) Center. Since then, total lightning observations have become an essential tool for forecasters during real-time warning operations. One of the operational advantages of the NALMA is the two-minute temporal resolution of the data. This provides forecasters with two to three updates during a typical volume scan of the WSR-88D radar.

White, Kristopher↗
NASA NTRS2015

Geomorphic and Geologic Controls of Geohazards induced by Nepal's 2015 Gorkha Earthquake

The Gorkha earthquake (Magnitude 7.8) on 25 April 2015 and later aftershocks struck South Asia, killing approx.9,000 and damaging a large region. Supported by a large campaign of responsive satellite data acquisitions over the earthquake disaster zone, our team undertook a satellite image survey of the earthquakes induced geohazards in Nepal and China and an assessment of the geomorphic, tectonic, and lithologic controls on quake-induced landslides. Timely analysis and communication aided response and recovery and informed decision makers. We mapped 4,312 co-seismic and post-seismic landslides. We also surveyed 491 glacier lakes for earthquake damage, but found only 9 landslide-impacted lakes and no visible satellite evidence of outbursts. Landslide densities correlate with slope, peak ground acceleration, surface downdrop, and specific metamorphic lithologies and large plutonic intrusions.

earthquake↗
NASA NTRS2018

ALMA Spectral Line and Imaging Survey of a Low and a High Mass-Loss Rate AGB Star Between 335 and 362 GHz

Context. Low and intermediate mass stars are known to power strong stellar winds when evolving through the asymptotic giant branch (AGB) phase. Initial mass, luminosity, temperature, and composition determine the pulsation characteristics of the star and the dust species formed in the pulsating photospheric layers. Radiation pressure on these grains triggers the onset of a stellar wind. However, as of today, we still cannot predict the wind mass-loss rates and wind velocities from first principles neither do we know which species are the first to condense in the upper atmospheric regions. Aims. We aim to characterise the dominant physical, dynamical, and chemical processes in the inner wind region of two archetypical oxygen-rich (C/O<1) AGB stars, that is, the low mass-loss rate AGB star R Dor (M~ 1x10(exp 7) M☉/yr) and the high mass-loss rate AGB star IK Tau (M~5x10(exp 6) M☉/yr). The purpose of this study is to observe the key molecular species contributing to the formation of dust grains and to cross-link the observed line brightnesses of several species to the global and local properties of the star and its wind. Methods. A spectral line and imaging survey of IK Tau and R Dor was made with ALMA between 335 and 362 GHz (band 7) at a spatial resolution of ~150 mas, which corresponds to the locus of the main dust formation region of both targets. Results. Some two hundred spectral features from 15 molecules (and their isotopologues) were observed, including rotational lines in both the ground and vibrationally excited states (up to v=5 for SiO). Detected species include the gaseous precursors of dust grains such as SiO, AlO, AlOH, TiO, and TiO2.We present a spectral atlas for both stars and the parameters of all detected spectral features. A clear dichotomy for the sulphur chemistry is seen: while CS, SiS, SO, and SO2 are abundantly present in IK Tau, only SO and SO2 are detected in R Dor. Also other species such as NaCl, NS, AlO, and AlOH display a completely different behaviour. From some selected species, the minor isotopologues can be used to assess the isotopic ratios. The channel maps of many species prove that both large and small-scale inhomogeneities persist in the inner wind of both stars in the form of blobs, arcs, and/or a disk. The high sensitivity of ALMA allows us to spot the impact of these correlated density structures in the spectral line profiles. The spectral lines often display a half width at zero intensity much larger than expected from the terminal velocity, v1, previously derived for both objects (36 km/s versus v(∞)~17.7 km/s for IK Tau and 23 km/s versus v(∞)~5.5 km/s for R Dor). Both a more complex 3D morphology and a more forceful wind acceleration of the (underlying) isotropic wind can explain this trend. The formation of fractal grains in the region beyond _400 mas can potentially account for the latter scenario. From the continuum map, we deduce a dust mass of ~3.7 x 10(exp 7) M☉ and ~2 x 10(ex0 8) M☉ for IK Tau and R Dor, respectively. Conclusions. The observations presented here provide important constraints on the properties of these two oxygen-dominated AGB stellar winds. In particular, the ALMA data prove that both the dynamical and chemical properties are vastly different for this high mass-loss rate (IK Tau) and low mass-loss rate (R Dor) star.

Stars: AGB and post-AGB, Stars: mass loss, Stars: ↗
NASA NTRS2018

ALMA Spectral Line and Imaging Survey of a Low and a High Mass-Loss Rate AGB Star Between 335 and 362 GHz

Context. Low and intermediate mass stars are known to power strong stellar winds when evolving through the asymptotic giant branch (AGB) phase. Initial mass, luminosity, temperature, and composition determine the pulsation characteristics of the star and the dust species formed in the pulsating photospheric layers. Radiation pressure on these grains triggers the onset of a stellar wind. However, as of today, we still cannot predict the wind mass-loss rates and wind velocities from first principles neither do we know which species are the first to condense in the upper atmospheric regions. Aims. We aim to characterise the dominant physical, dynamical, and chemical processes in the inner wind region of two archetypical oxygen-rich (C/O < 1) AGB stars, that is, the low mass-loss rate AGB star R Dor (M’ ∼ 1 × 10(exp −7) M/yr) and the high mass-loss rate AGB star IK Tau (M’ ∼ 5 × 10(exp −6) M/yr). The purpose of this study is to observe the key molecular species contributing to the formation of dust grains and to cross-link the observed line brightnesses of several species to the global and local properties of the star and its wind. Methods. A spectral line and imaging survey of IK Tau and R Dor was made with ALMA between 335 and 362 GHz (band 7) at a spatial resolution of ∼150 mas, which corresponds to the locus of the main dust formation region of both targets. Results. Some two hundred spectral features from 15 molecules (and their isotopologues) were observed, including rotational lines in both the ground and vibrationally excited states (up to v = 5 for SiO). Detected species include the gaseous precursors of dust grains such as SiO, AlO, AlOH, TiO, and TiO2. We present a spectral atlas for both stars and the parameters of all detected spectral features. A clear dichotomy for the sulphur chemistry is seen: while CS, SiS, SO, and SO2 are abundantly present in IK Tau, only SO and SO2 are detected in R Dor. Also other species such as NaCl, NS, AlO, and AlOH display a completely different behaviour. From some selected species, the minor isotopologues can be used to assess the isotopic ratios. The channel maps of many species prove that both large and small-scale inhomogeneities persist in the inner wind of both stars in the form of blobs, arcs, and/or a disk. The high sensitivity of ALMA allows us to spot the impact of these correlated density structures in the spectral line profiles. The spectral lines often display a half width at zero intensity much larger than expected from the terminal velocity, v∞, previously derived for both objects (36 km/s versus v(∞) ∼ 17.7 km/s for IK Tau and 23 km/s versus v(∞) ∼ 5.5 km/s for R Dor). Both a more complex 3D morphology and a more forceful wind acceleration of the (underlying) isotropic wind can explain this trend. The formation of fractal grains in the region beyond ∼400 mas can potentially account for the latter scenario. From the continuum map, we deduce a dust mass of ∼3.7 × 10(exp −7) Mand ∼2 × 10(exp −8) M for IK Tau and R Dor, respectively. Conclusions. The observations presented here provide important constraints on the properties of these two oxygen-dominated AGB stellar winds. In particular, the ALMA data prove that both the dynamical and chemical properties are vastly different for this high mass-loss rate (IK Tau) and low mass-loss rate (R Dor) star.

L. Decin↗
DOE OSTI2020

Constraining level densities through quantitative correlations with cross-section data

The adopted level densities (LD) for the nuclei produced through different reaction mechanisms significantly impact the accurate calculation of cross sections for the different reaction channels. Many common LD models make simplified assumptions regarding the overall behavior of the total LD and the intrinsic spin and parity distributions of the excited states. However, very few experimental constraints are taken into account in these models: LD at neutron separation energy coming from average spacings of s- and p-wave resonances ( D 0 and D 1 , respectively) whenever they have been previously measured, and the sometimes subjective extrapolation of discrete levels. These, however, constrain the LD only in very specific regions of excitation energy, and for specific spins and parities. This work aims to establish additional experimental constraints on LD through quantitative correlations between cross sections and LD. This allows for fitting and the determination of detailed structures in LD. For this we use the microscopic Hartree-Fock-Bogoliubov (HFB) LD as a starting point as the HFB LD provide a more realistic spin and parity distributions than phenomenological models such as Gilbert-Cameron (GC). We then associate variations predicted by the HFB model with the structure observed in double-differential cross sections at low outgoing neutron energy, a region that is dominated by the LD input. We also use (n, p) on 56 Fe , as an example case where angle-integrated cross sections are extremely sensitive to LD. For comparison purposes we also perform calculations with the GC model. With this approach we are able to perform fits of the LD based on actual experimental data, constraining the model and ensuring its consistency. This approach can be particularly useful in extrapolating the LD to nuclei for which high-excited discrete levels and/or values of D 0 or D 1 are unknown. Finally, it also predicts neutron-induced inelastic γ cross sections that in some cases can differ significantly from more standard phenomenological LD models such as GC.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Reference Correlations for the Density and Viscosity of Molten Alkali and Alkaline Earth Fluoride Salts

While there is a significant body of literature pertaining to thermophysical property measurements of molten salts, there is often a wide degree of variability among independent measurements of the same compounds. As such, the scientific community benefits greatly from an unbiased, independent assessment of duplicate datasets, so that reference correlations which describe these thermophysical properties as functions of temperature can be determined and then commonly used by researchers, scientists, and engineers. With regard to molten fluoride compounds, a significant time has elapsed since density and viscosity reference correlations have been determined; Janz conducted the most recent effort, in 1988, to provide reference correlations for the densities and viscosities of molten fluoride compounds via the National Standard Reference Data System coordinated by the National Bureau of Standards. Since then, new data have been published for molten fluoride compounds, and a new precedent has surfaced for putting forth reference correlations that involve fitting to multiple primary datasets. In this work, reference correlations are put forth for molten alkali and alkaline earth fluoride compounds in an effort to provide updated, improved correlations for general use. For molten alkali fluoride densities, estimated uncertainties with a 95% confidence interval are summarized as follows: LiF (0.63%), NaF (0.48%), KF (0.76%), RbF (0.93%), and CsF (0.75%). For molten alkaline earth fluoride densities, an estimated uncertainty was not able to be quantified for BeF 2 because of limited data; however, estimated uncertainties with a 95% confidence interval are summarized as follows for the remaining alkaline earth fluorides: MgF 2 (1.5%), CaF 2 (0.92%), SrF 2 (1.6%), and BaF 2 (0.23%). For molten alkali fluoride viscosities, uncertainty was not able to be quantified for RbF and CsF because of limited data; however, estimated uncertainties with a 95% confidence interval are summarized as follows for the remaining alkali fluorides: LiF (4.4%), NaF (3.0%), and KF (4.0%). For molten alkaline earth fluoride viscosities, limited consistent data resulted in the recommendation of single datasets (from literature) that are deemed to be the most trustworthy based on the quality of the underlying experimental studies.

Birri, A. [Oak Ridge National Laboratory (ORNL), O↗
NASA NTRS1978

The correlation function for density perturbations in an expanding universe. III The three-point and predictions of the four-point and higher order correlation functions

Higher-order correlation functions for the large-scale distribution of galaxies in space are investigated. It is demonstrated that the three-point correlation function observed by Peebles and Groth (1975) is not consistent with a distribution of perturbations that at present are randomly distributed in space. The two-point correlation function is shown to be independent of how the perturbations are distributed spatially, and a model of clustered perturbations is developed which incorporates a nonuniform perturbation distribution and which explains the three-point correlation function. A model with hierarchical perturbations incorporating the same nonuniform distribution is also constructed; it is found that this model also explains the three-point correlation function, but predicts different results for the four-point and higher-order correlation functions than does the model with clustered perturbations. It is suggested that the model of hierarchical perturbations might be explained by the single assumption of having density fluctuations or discrete objects all of the same mass randomly placed at some initial epoch.

Mcclelland, J.↗
NASA NTRS2001

Sound Source Identification Through Flow Density Measurement and Correlation With Far Field Noise

Sound sources in the plumes of unheated round jets, in the Mach number range 0.6 to 1.8, were investigated experimentally using "casuality" approach, where air density fluctuations in the plumes were correlated with the far field noise. The air density was measured using a newly developed Molecular Rayleigh scattering based technique, which did not require any seeding. The reference at the end provides a detailed description of the measurement technique.

Panda, J.↗
NASA NTRS1994

Correlations in cosmic density fields

A method is proposed to place constraints on the functional form of the high-order correlation functions zeta(sub n) that arise in cosmic density fields at large scales. This technique is based on a mass-in-cell statistic and a difference of mass in partitions of a cell. The relationship between these measures is sensitive to the formal structure of the zeta(sub n) as well as their amplitudes. This relationship is quantified in several theoretical models of structure, based on the hierarchical clustering paradigm. The results lead to a test for specific types of hierarchical clustering that is sensitive to correlations of all orders. The method is applied to examples of simulated large-scaled structure dominated by cold dark matter. In the preliminary study, the hierarchical paradigm appears to be a realistic approximation over a broad range of the scales. Furthermore, there is evidence that graphs of low-order vertices are dominant. On the basis of simulated data a phenomological model is specified that gives a good representation of clustering from linear scales to the strongly clustered regime (zeta(sub 2) approximately 500).

Bromley, B. C.↗
NASA NTRS2002

Measurement of Correlation Between Flow Density, Velocity, and Density*velocity(sup 2) with Far Field Noise in High Speed Jets

To locate noise sources in high-speed jets, the sound pressure fluctuations p', measured at far field locations, were correlated with each of radial velocity v, density rho, and phov(exp 2) fluctuations measured from various points in jet plumes. The experiments follow the cause-and-effect method of sound source identification, where correlation is related to the first, and correlation to the second source terms of Lighthill's equation. Three fully expanded, unheated plumes of Mach number 0.95, 1.4 and 1.8 were studied for this purpose. The velocity and density fluctuations were measured simultaneously using a recently developed, non-intrusive, point measurement technique based on molecular Rayleigh scattering. It was observed that along the jet centerline the density fluctuation spectra S(sub rho) have different shapes than the radial velocity spectra S(sub v), while data obtained from the peripheral shear layer show similarity between the two spectra. Density fluctuations in the jet showed significantly higher correlation, than either rhov(sub 2) or v fluctuations. It is found that a single point correlation from the peak sound emitting region at the end of the potential core can account for nearly 10% of all noise at 30 to the jet axis. The correlation, representing the effectiveness of a longitudinal quadrupole in generating noise 90 to the jet axis, is found to be zero within experimental uncertainty. In contrast rhov(exp 2) fluctuations were better correlated with sound pressure fluctuation at the 30 location. The strongest source of sound is found to lie at the centerline and beyond the end of potential core.

Panda, Jayanta↗
NASA NTRS1977

The correlation function for density perturbations in an expanding universe. II - Nonlinear theory

A formalism is developed to find the two-point and higher-order correlation functions for a given distribution of sizes and shapes of perturbations which are randomly placed in three-dimensional space. The perturbations are described by two parameters such as central density and size, and the two-point correlation function is explicitly related to the luminosity function of groups and clusters of galaxies

Mcclelland, J.↗
DOE OSTI2020

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Temperature and density anti-correlations in solar wind fluctuations

Recent theoretical investigations of low Mach number flows, that describe two distinct approaches by fluids to the incompressible regime are summarized. The first includes the effects of relatively strong density and temperature fluctuations (Type I), while the second places fluctuations in mechanical pressure, density, and temperature on an equal footing (Type II). In the latter case, the relations between density and pressure are recovered, whereas the former case yields departures from incompressible behavior in that density and temperature fluctuations are predicted to be anti-correlated. It is suggested that nearly incompressible fluids can be classified as either Type I or II, and it is shown that the well-known pressure-balanced structures represent a subclass of static solutions within this classification. Two examples from Voyager data illustrate the potential for observing these distinct nearly incompressible dynamical ordering in the solar wind.

Zank, G. P.↗
DOE OSTI2025

Towards excitations and dynamical quantities in correlated lattices with density matrix embedding theory

Density matrix embedding theory (DMET) provides a framework to describe ground-state expectation values in strongly correlated systems, but its extension to dynamical quantities is still an open problem. We show one route to obtaining excitations and dynamical spectral functions by using the techniques of DMET to approximate the matrix elements that arise in a single-mode inspired excitation ansatz. We demonstrate this approach in the one-dimensional Hubbard model, comparing the neutral excitations, single-particle density of states, charge, and spin dynamical structure factors to benchmarks from the Bethe ansatz and density matrix renormalization group. Finally, our work highlights the potential of these ideas in building computationally efficient approaches for dynamical quantities.

1-dimensional systems↗
DOE OSTI2022

Meta-GGA exchange-correlation free energy density functional to increase the accuracy of warm dense matter simulations

We discuss strategies for thermalization of the ground-state meta-generalized gradient approximation (meta-GGA) exchange-correlation (XC) functionals. A simple but accurate scheme is implemented via universal additive thermal correction to XC using a perturbative-like self-consistent approach. The additive correction with explicit temperature dependence is applied to the ground-state deorbitalized, strongly constrained and appropriately normed (SCAN-L) meta-GGA XC leading to thermal XC functional denoted here as T-SCAN-L. Thermal T-SCAN-L meta-GGA functional shows significant improvement in density functional theory calculation accuracy for warm dense matter by a factor of 3 to 10, achieving unprecedented accuracy of total pressure between a few tenths and 1% when compared to traditional XC functionals, as demonstrated by the comparison to pathintegral Monte Carlo simulations for helium equation of state. Furthermore, the T-SCAN-L calculations of dc conductivity of warm dense aluminum also give better agreement with experiments over other XC functionals such as PBE and SCAN-L.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1982

Harmonic well matter densities and Pauli correlation effects in heavy-ion collisions

A generalized optical model heavy ion reaction theory is extended to include correlation effects between projectile and target constituents according to the Pauli exclusion principle. These correlation effects are significant for accurately predicting cross sections for projectile nucleus abrasions, but are relatively unimportant for determining total and absorption cross sections for heavy ion collisions. For lighter nuclei, predictive capabilities were also improved by developing an analytic method for extracting their nuclear single particle density distributions from experimentally measured harmonic well charge density distributions. This improved theory is compared with previous theoretical predictions and recent experimental results.

Townsend, L. W.↗