Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “densification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Consolidation of Si3N4 without additives (by hot isostatic pressing)

The potential of using hot isostatic pressing (HIP'ing) technique to produce dense silicon nitride materials without or with a reduced amount of additives (much less than 5 w/o) was investigated. Hot isostatic pressing technique can provide higher pressure and temperature than hot pressing can, thus has the potential of requiring less densification aids to consolidate Si3N4 materials. It was anticipated that if such dense materials could be fabricated, the high temperature strength of the material should be improved significantly. Observations on the phase transformation, densification behavior, and microstructures of the samples are also documented. Density, microhardness, four point bend strength (room temperature and 1370 C) were measured on selected densified materials.

Yeh, H. C.↗
NASA NTRS1984

Effects of applied pressure on hot-pressing of Beta-SiC

The effects of applied pressure on the densification during hot pressing of beta-SiC compacts were investigated. Beta-SiC powder is Starck made and has the average particle size of about 0.7 micrometer. Hot pressing experiments were carried out in graphite dies at temperatures of 1700 deg to 2300 deg C and at the pressures up to 1000 kg/sq cm. The compacts containing 1 weight percent B4C were examined. Sintered compacts were examined for microstructure and the Rockwell A-scale hardness was measured. The B4C addition was very effective to mitigate the hot pressing conditions. It is found that densification goes with the strengthening of the bonding and does not occur in particle deformation due to concentrated stress.

Kinoshita, M.↗
NASA NTRS1983

Compositional effects on Si3N4 fracture surfaces

Surface analysis techniques (X-ray, infrared reflection spectroscopy, Auger electron spectroscopy) applied to the same samples reveal that fracture surfaces of Si3N4 with Y2O3 densification aids possess a higher concentration of oxygen than the bulk. The oxide densification aids thus concentrate in the grain boundaries, and even low-temperature fracture is seen as occurring preferentially within the oxygen-enriched grain boundaries. It is found that increasing the concentrations of Y2O3 and Al2O3 increases the oxygen content of the fracture surface. A range of 13-15 percent Y2O3 + 6 percent Al2O3 gives an amorphous grain-boundary phase that is resistant to devitrification. Fracture occurs through the amorphous phase, and heat treatment at 1000 C has little effect on the amorphous phase.

Hench, L. L.↗
NASA NTRS1985

Metallurgical and mechanical phenomena due to rubbing of titanium against sintered powder Nichrome

Metallurgical and mechanical changes occurring during high-speed rubbing of Ti-6Al-4V blade specimens against an abradable Nichrome aircraft engine seal material were studied using optical microscopy, electron microscopy, and microhardness techniques. Evidence of temperatures above the beta transus of Ti-6Al-4V (1000 C) and of thermal hardening was found on blade tips that exhibited undesirable abrading characteristics resulting in high forces of interaction, high temperatures, and smearing. The material within the layer of the corresponding seals was found to be work-hardened to a depth of about 0.1 mm and showed evidence of densification extending to a depth of about 0.5 mm below the rubbed surface. Wear particles produced by rub interactions that generated cleanly abraded seal surfaces were found to be several times larger than those produced during interactions which showed evidence of surface smearing and seal densification.

Zenas, R.↗
NASA NTRS1985

Colloidal Oxide Properties and Kinetic Studies

Silica based oxide particles prepared by various methods are compared in terms of their gellation kinetics, densification kinetics, and microable structural evolutions begin at very low temperature. Additional work reported in literature further suggested that the colloidal behaviors and the dried gel structures of the same oxide from different preparation techniques differ fundamentally. These differences significantly affect the densification kinetics and the product microstructure. Gravitational segregation of particles of different sizes in a gravitational field is modelled as a diffusion/segregation problem. A structural free volume model was used to describe the activation process of jump statistics. The sizes of the particles, the interstices, and their packing topology are accounted for in the estimation of the free volume. An attempt frequency is ascribed to particles to account for the vibrational rearrangement during powder packing.

Chen, I. W.↗
NASA NTRS1987

Cast iron freezing mechanisms

This task focused on liquid phase sintering and infiltration studies of refractory metals and metal composites. Particular emphases was placed on those powered metal compacts which produce liquid alloys in sintering. For this class of materials, heating to a two phase region causes the constituent components to react, forming an alloy liquid which must wet the solid phase. Densification is initially driven by the free energy effects which cause rapid rearrangement. Further densification occurs by evaporation and condensation, surface diffusion, bulk flow, and volume diffusion.

Lillybeck, N. P.↗
NASA NTRS1992

Smooth-Surfaced Carbon/Carbon Reflector Panels

Surface-densification technique integral to fabrication of reflective, lightweight, low-outgassing radio-antenna-reflector panels including carbon/carbon surface laminates supported by carbon/carbon core structures. Densification prevents "print-through" of carbon fibers on surface. When properly densified, surface polished to smooth finish.

Schmitigal, Wesley P.↗
NASA NTRS1991

Lunar regolith penetrators and cutters

An apparatus was designed and built for conducting simulation experiments on cutting tool penetration in the centrifuge. This equipment is mounted on the laminar container which is used for the regolith densification study, so that the end product of the latter, i.e., a regolith bed with the proper density profile, can be used directly for the penetration tests. In this apparatus, an etching tool is suspended through a pulley system by the action of a double acting air cylinder. By adjusting the air pressure acting on each side of the cylinder, the net downward force acting on the tool can be controlled. The penetration of the tool is measured by an LVDT. This apparatus was proof-tested in the centrifuge and is ready for use in conjunction with the regolith densification experiments.

Barnes, Frank↗
NASA NTRS1991

Modeling the interaction of ultrasound with pores

Factors that affect ultrasonic velocity sensing of density during consolidation of metal powders are examined. A comparison is made between experimental results obtained during the final stage of densification and the predictions of models that assume either a spherical or a spheroidal pore shape. It is found that for measurements made at low frequencies during the final stage of densification, relative density (pore fraction) and pore shape are the two most important factors determining the ultrasonic velocity, the effect of pore size is negligible.

Lu, Yichi↗
NASA NTRS1993

On the development of constitutive relations for metallic powders

This article describes the development of elastic and plastic constitutive relations as functions of relative density for partially consolidated -100 mesh aluminum powder. First, measurements of yield stress as a function of stress state and relative density are described. Measurements of the plastic strain increments associated with yielding in unconstrained compression tests and elastic properties, both as functions of relative density, are also described. The experimental results are combined with the associated flow rule to show that the yield surface is asymmetric with respect to hydrostatic tension and compression. Second, it is shown that the yield stress results can be represented by a two-part (capped Drucker-Prager) yield surface. The consolidation yield surface moves along the hydrostatic stress axis during densification, while the shear yield surface approaches the Mises yield surface. For the Al powder used in the present investigation, superposition of shear stress on a hydrostatic stress state aids the densification process. However, the hydrostatic stress requirement was found to be reduced by only about 20 pct for relative densities below 0.98.

Watson, T. J.↗
NASA NTRS1996

Testing of electroformed deposited iridium/powder metallurgy rhenium rockets

High-temperature, oxidation-resistant chamber materials offer the thermal margin for high performance and extended lifetimes for radiation-cooled rockets. Rhenium (Re) coated with iridium (Ir) allow hours of operation at 2200 C on Earth-storable propellants. One process for manufacturing Ir/Re rocket chambers is the fabrication of Re substrates by powder metallurgy (PM) and the application of Ir coatings by using electroformed deposition (ED). ED Ir coatings, however, have been found to be porous and poorly adherent. The integrity of ED Ir coatings could be improved by densification after the electroforming process. This report summarizes the testing of two 22-N, ED Ir/PM Re rocket chambers that were subjected to post-deposition treatments in an effort to densify the Ir coating. One chamber was vacuum annealed, while the other chamber was subjected to hot isostatic pressure (HIP). The chambers were tested on gaseous oxygen/gaseous hydrogen propellants, at mixture ratios that simulated the oxidizing environments of Earth-storable propellants. ne annealed ED Ir/PM Re chamber was tested for a total of 24 firings and 4.58 hr at a mixture ratio of 4.2. After only 9 firings, the annealed ED Ir coating began to blister and spall upstream of the throat. The blistering and spalling were similar to what had been experienced with unannealed, as-deposited ED Ir coatings. The HIP ED Ir/PM Re chamber was tested for a total of 91 firings and 11.45 hr at mixture ratios of 3.2 and 4.2. The HIP ED Ir coating remained adherent to the Re substrate throughout testing; there were no visible signs of coating degradation. Metallography revealed, however, thinning of the HIP Ir coating and occasional pores in the Re layer upstream of the throat. Pinholes in the Ir coating may have provided a path for oxidation of the Re substrate at these locations. The HIP ED Ir coating proved to be more effective than vacuum annealed and as-deposited ED Ir. Further densification is still required to match the integrity of chemically vapor deposited Ir coatings. Despite this, the successful long duration testing of the HIP ED Ir chamber, in an oxidizing environment comparable to Earth-storable propellants, demonstrated the viability of this Ir/Re rocket fabrication process.

Reed, Brian D.↗
NASA NTRS1999

Testing of Densified Liquid Hydrogen Stratification in a Scale Model Propellant Tank

Propellant densification has been identified as a critical technology in the development of a single stage to orbit (SSTO) launch vehicle. The densification of cryogenic propellant through sub-cooling allows more propellant to be stored in a given volume. This allows for higher propellant mass fractions than would otherwise be possible with conventional, normal boiling point, cryogenic fluids. One critical step in determining the viability of densified propellant technology for launch vehicles is to perform the sequential process necessary to load a propellant tank with densified propellants. This paper describes a test program that was conducted at NASA to demonstrate the ability to load densified LH2 into a sub-scale propellant rank. This work was done through a collaborative effort between NASA Lewis Research Center and the Lockheed Martin Michoud Space Systems (LMMSS). The tank, is made from composite materials similar to that to be used on X-33, is formed from two lobes with a center seprum. Test results are shown for data that was collected on filling the sub-scale tank with densified liquid hydrogen propellant that was produced at the NASA Plum Brook Station. Data is compared to analytical predictions.

Greene, W. D.↗
NASA NTRS2009

Gauging Systems Monitor Cryogenic Liquids

Rocket fuel needs to stay cool - super cool, in fact. The ability to store gas propellants like liquid hydrogen and oxygen at cryogenic temperatures (below -243 F) is crucial for space missions in order to reduce their volumes and allow their storage in smaller (and therefore, less costly) tanks. The Agency has used these cryogenic fluids for vehicle propellants, reactants, and life support systems since 1962 with the Centaur upper stage rocket, which was powered with liquid oxygen and liquid hydrogen. During proposed long-duration missions, super-cooled fluids will also be used in space power systems, spaceports, and lunar habitation systems. In the next generation of launch vehicles, gaseous propellants will be cooled to and stored for extended periods at even colder temperatures than currently employed via a process called densification. Densification sub-cools liquids to temperatures even closer to absolute zero (-459 F), increasing the fluid s density and shrinking its volume beyond common cryogenics. Sub-cooling cryogenic liquid hydrogen, for instance, from 20 K (-423 F) to 15 K (-432.4 F) reduces its mass by 10 percent. These densified liquid gases can provide more cost savings from reduced payload volume. In order to benefit from this cost savings, the Agency is working with private industry to prevent evaporation, leakage, and other inadvertent loss of liquids and gases in payloads - requiring new cryogenic systems to prevent 98 percent (or more) of boil-off loss. Boil-off occurs when cryogenic or densified liquids evaporate, and is a concern during launch pad holds. Accurate sensing of propellants aboard space vehicles is also critical for proper engine shutdown and re-ignition after launch, and zero boil-off fuel systems are also in development for the Altair lunar lander.

Source record↗
NASA NTRS2011

High temperature strain gages

A ceramic strain gage based on reactively sputtered indium-tin-oxide (ITO) thin films is used to monitor the structural integrity of components employed in aerospace propulsion systems operating at temperatures in excess of 1500.degree. C. A scanning electron microscopy (SEM) of the thick ITO sensors reveals a partially sintered microstructure comprising a contiguous network of submicron ITO particles with well defined necks and isolated nanoporosity. Densification of the ITO particles was retarded during high temperature exposure with nitrogen thus stabilizing the nanoporosity. ITO strain sensors were prepared by reactive sputtering in various nitrogen/oxygen/argon partial pressures to incorporate more nitrogen into the films. Under these conditions, sintering and densification of the ITO particles containing these nitrogen rich grain boundaries was retarded and a contiguous network of nano-sized ITO particles was established.

Gregory, Otto J.↗
NASA NTRS2009

Experimental Results of Integrated Refrigeration and Storage System Testing

Launch operations engineers at the Kennedy Space Center have identified an Integrated Refrigeration and Storage system as a promising technology to reduce launch costs and enable advanced cryogenic operations. This system uses a close cycle Brayton refrigerator to remove energy from the stored cryogenic propellant. This allows for the potential of a zero loss storage and transfer system, as well and control of the state of the propellant through densification or re-liquefaction. However, the behavior of the fluid in this type of system is different than typical cryogenic behavior, and there will be a learning curve associated with its use. A 400 liter research cryostat has been designed, fabricated and delivered to KSC to test the thermo fluid behavior of liquid oxygen as energy is removed from the cryogen by a simulated DC cycle cryocooler. Results of the initial testing phase focusing on heat exchanger characterization and zero loss storage operations using liquid oxygen are presented in this paper. Future plans for testing of oxygen densification tests and oxygen liquefaction tests will also be discussed. KEYWORDS: Liquid Oxygen, Refrigeration, Storage

Notardonato, W. U.↗
NASA NTRS2015

Methodology for Producing a Uniform Distribution of UO2 in a Tungsten Matrix

Current work at NASA's Marshall Space Flight Center (MSFC) is focused on the development CERMET fuel materials for Nuclear Thermal Propulsion (NTP). The CERMETs consist of uranium dioxide (UO2) fuel particles embedded in a tungsten (W) metal matrix. Initial testing of W-UO2 samples fabricated from fine angular powders performed reasonably well, but suffered from significant fuel loss during repeated thermal cycling due to agglomeration of the UO2 (1). The blended powder mixtures resulted in a non-uniform dispersion of the UO2 particles in the tungsten matrix, which allows rapid vaporization of the interconnected UO2 from the sample edges into the bulk material. Also, the angular powders create areas of stress concentrations due to thermal expansion mismatch, which eventually cracks the tungsten matrix. Evenly coating spherical UO2 particles with chemical vapor deposited (CVD) tungsten prior to consolidation was previously demonstrated to provide improved performance. However, the CVD processing technology is expensive and not currently available. In order to reduce cost and enhance performance, a powder coating process has been developed at MSFC to produce a uniform distribution of the spherical UO2 particles in a tungsten matrix. The method involves utilization of a polyethylene binder during mixing which leads to fine tungsten powders clinging to the larger UO2 spherical particles. This process was developed using HfO2 as a surrogate for UO2. Enough powder was mixed to make 8 discs (2cm diameter x 8mm thickness) using spark plasma sintering. A uniaxial pressure of 50 MPa was used at four different temperatures (2 samples at each temperature). The first two samples were heated to 1400C and 1500C respectively for 5 minutes. Densities for these samples were less than 85% of theoretical, so the time at temperature was increased to 20 minutes for the remaining samples. The highest densities were achieved for the two samples sintered at 1700C (approx. 92% of theoretical). Scanning electron microscopy (SEM) of the mixed powders and the sintered samples along with energy dispersive x-ray analysis was obtained. The SEM of the powders clearly show the fine W powder adhered to the larger HfO2 particles and a uniform distribution of HfO2 particles in a tungsten matrix upon densification. Vicker's Microhardness testing was also performed on all samples using 0.5, 1.0 and 2.0 kg loads. Five indents were made at each load level. All indents were placed in the tungsten matrix to assist as a proxy in measuring densification. The highest hardness value was obtained for the 1700C specimens. The hardness average for these samples was 312.14 MPa. This powder processing method has been applied to W/UO2 powders with the SEM of the powders appearing similar to the W/HfO2 powder images.

Tucker, Dennis S.↗
NASA NTRS2018

Transient Modeling of Large Scale Integrated Refrigeration and Storage Systems

Recently, next generation techniques and designs were demonstrated using Integrated Refrigeration and Storage (IRAS) for large scale storage of liquid hydrogen at NASA Kennedy Space Center (KSC) in Florida. Zero boil-off, densification, and in-situ liquefaction of hydrogen were achieved at various fill levels inside a custom-built 125,000 liter, horizontal-cylindrical IRAS tank, validating the applicability of the concept for large scale cryo-fluid storage architectures. This paper will discuss a number of transient physics models developed to predict the bulk behavior of large IRAS systems, and the comparison of those models to data gathered during the KSC test campaign. In an attempt to extent their usefulness to future IRAS designs, these models were agnostic with respect to stored fluid, tank size and geometry. Behavior during densification testing was examined at three fill levels, and ultimately the depressurization and bulk temperature trends of the KSC tests were predicted with good accuracy.

Swanger, Adam M.↗
NASA NTRS2018

Transient Modeling of Large Scale Integrated Refrigeration and Storage Systems

Recently, next generation techniques and designs were demonstrated using Integrated Refrigeration and Storage (IRAS) for large scale storage of liquid hydrogen at NASA Kennedy Space Center (KSC) in Florida. Zero boil-off, densification, and in-situ liquefaction of hydrogen were achieved at various fill levels inside a custom-built 125,000 liter, horizontal-cylindrical IRAS tank, validating the applicability of the concept for large scale cryo-fluid storage architectures. This paper will discuss a number of transient physics models developed to predict the bulk behavior of large IRAS systems, and the comparison of those models to data gathered during the KSC test campaign. In an attempt to extent their usefulness to future IRAS designs, these models were agnostic with respect to stored fluid, tank size and geometry. Behavior during densification testing was examined at three fill levels, and ultimately the depressurization and bulk temperature trends of the KSC tests were predicted with good accuracy.

Swanger, Adam M.↗