Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conductive ink”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Charge regulation effects on colloidal mixture nanoparticles

Changes in pH within a system containing dissociable sites affect the protonation and deprotonation of these groups, thereby influencing their physical properties. In response, the system modifies their surface charge, affecting electrostatic interactions, aggregation, stability, and structural behavior. Although the pH can be tuned in experiments, it is difficult to model this phenomenon using simulations or theoretical approaches. Here, we perform hybrid Monte Carlo-molecular dynamics simulations to model charge regulation effects in an equimolar colloidal charged system. We compare charge regulation effects with those of a system in which the charges of colloidal nanoparticles are not dissociable. The comparison between the two cases modifies the phase diagram, and it changes the volume fraction where a percolation network of nanoparticles is found. Charge regulation is found to destroy network formation, as the charge in the nanoparticles is modified because of the cooperativity dependency of the degree of charge dissociation sites among the nanoparticles favoring cluster formation. Furthermore, our work suggests that the ionic and/or electronic conductivity in functionalized nanoparticles can be modified by changing pH values. It also guides the experimental design of oppositely charged nanoparticles as inks for 3D printing processes.

Classical statistical mechanics↗
DOE OSTI2024

Laser‐Sintered Silver Metallization for Silicon Heterojunction Photovoltaic Cells

Herein, a novel metallization technique is reported for crystalline silicon heterojunction (SHJ) solar cells in which silver (Ag) fingers are printed on the SHJ substrates by dispensing Ag nanoparticle‐based inks through a needle and then sintered with a continuous‐wave carbon dioxide (CO 2 ) laser. The impact of the Ag ink viscosity on the line quality and the line resistance is investigated on three Ag inks with different viscosities. Increasing ink viscosity yields higher Ag contact heights, larger aspect ratios, and lower line resistance values. The Ag line height increases from less than a micrometer to ≈18.62 ± 3.48 μm with the increasing viscosity. Photoluminescence imaging shows that the low‐resistance Ag metal contacts obtained do not result in any passivation damage of the SHJ substrate. This is because the wavelength of light emitted from the CO 2 laser (i.e., 10.6 μm) leads to optical absorption in the Ag, but this light is effectively transparent to the transparent conductive oxide film, amorphous silicon films, and crystalline silicon substrate. Bulk resistivity values as low as 6.5 μΩ cm are obtained for the laser‐sintered Ag contact and printed using the Ag ink with the highest viscosity in this work.

Mousumi, Jannatul Ferdous↗
DOE OSTI2023

Electrode ink deposition system for high-throughput polymer electrolyte fuel cell

Systems for creating electrodes for polymer electrolyte membrane fuel cells include an XY stage having a heated vacuum table physically coupled to the XY stage. The vacuum table has a working face with a plurality of channels formed therein to communicate vacuum pressure from a port coupled to a vacuum source to the channels. A sheet of perforated heat-conductive material has staggered holes configured to evenly distribute the vacuum pressure from the channels through the perforated sheet. A heat-conductive wire mesh is placed over the perforated sheet, and has openings smaller than the staggered holes such that a membrane material placed on the wire mesh is not deformed by the vacuum pressure. A nanopipette or micropipette coupled to a pump is configured to deposit electrode ink onto an exposed surface of the membrane material as the controller device causes the XY stage to move the vacuum table to control deposition of the electrode ink onto the surface of the membrane material.

Park, Jae Hyung↗
DOE OSTI2024

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗
DOE OSTI2024

Direct electron beam patterning of electro-optically active PEDOT:PSS

The optical and electronic tunability of the conductive polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has enabled emerging applications as diverse as bioelectronics, flexible electronics, and micro- and nano-photonics. High-resolution spatial patterning of PEDOT:PSS opens up opportunities for novel active devices in a range of fields. However, typical lithographic processes require tedious indirect patterning and dry etch processes, while solution-processing methods such as ink-jet printing have limited spatial resolution. Here, we report a method for direct write nano-patterning of commercially available PEDOT:PSS through electron-beam induced solubility modulation. The written structures are water stable and maintain the conductivity as well as electrochemical and optical properties of PEDOT:PSS, highlighting the broad utility of our method. We demonstrate the potential of our strategy by preparing prototypical nano-wire structures with feature sizes down to 250 nm, an order of magnitude finer than previously reported direct write methods, opening the possibility of writing chip-scale microelectronic and optical devices. We finally use the high-resolution writing capabilities to fabricate electrically-switchable optical diffraction gratings. We show active switching in this archetypal system with >95 % contrast at CMOS-compatible voltages of +2 V and -3 V, offering a route towards highly-miniaturized dynamic optoelectronic devices.

42 ENGINEERING↗
DOE OSTI2021

Additive Manufacturing of Porous Ceramics With Foaming Agent

The macro-porous ceramics has promising durability and thermal insulation performance. As porous ceramics find more and more applications across many industries, a cost-effective and scalable additive manufacturing technique for fabricating macro-porous ceramics is highly desirable. Herein, we reported a facile additive manufacturing approach to fabricate porous ceramics and control the printed porosity. Several printable ceramic inks were prepared, and the foaming agent was added to generate gaseous bubbles in the ink, followed by the direct ink writing and the ambient-pressure and room-temperature drying to create the three-dimensional geometries. In this work, a set of experimental studies were performed to optimize the printing quality. The results revealed the optimal process parameters for printing the foamed ceramic ink with a high spatial resolution and fine surface quality. Varying the concentration of the foaming agent enables the controllability of the structural porosity. The maximum porosity can reach 85%, with a crack-free internal porous structure. The tensile tests showed that the printed macro-porous ceramics possessed enhanced durability with the addition of fiber. With a high-fidelity three-dimensional (3D) printing process and the precise controllability of the porosity, we showed that the printed samples exhibited a remarkably low thermal conductivity and durable mechanical strength.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cost-Effective Additive Manufacturing of Ambient Pressure-Dried Silica Aerogel

The conventional manufacturing processes for aerogel insulation materials mostly rely on the supercritical drying, which suffers from issues of massive energy consumption, high-cost equipment, and prolonged processing time. Considering the large market demand for the aerogel insulation material in the next decade, a cost-effective and scalable fabrication technique is highly desired. In this paper, a direct ink writing (DIW) method is used to three-dimensionally fabricate the silica aerogel insulation material, followed by room-temperature and ambient pressure drying. Compared with the supercritical drying and freeze-drying techniques, the reported method significantly reduces the fabrication time and costs. The cost-effective DIW technique offers the capability to print complex hollow internal structures, coupled with the porous aerogel structure, it is found to be beneficial for the thermal insulation property. In this work, the addition of fiber to the ink assures the durability of the fabricated product, without sacrificing the thermal insulation performance. The foam ink preparation methods and the printability are demonstrated in this paper, along with the printing of complex three-dimensional geometries. The thermal insulation performance of the printed objects is characterized, and the mechanical properties were also examined. The proposed approach is found to have a 56% reduction in the processing time. The printed silica aerogels exhibit a low thermal conductivity of 0.053 W m –1 K –1 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Low-Cost, Screen-Printed Silver Metal Complex Inks for Silicon Heterojunction Solar Cells

Screen printing using metal particle pastes, the current photovoltaic industry metallization standard, provides fast and reliable metal grids for silicon solar cells. Recently, metal complex or reactive metal inks are attracting research interest due to their significantly low cost and higher performance compared to traditional nanoparticle silver pastes. In this work, we demonstrate, for the first time, screen-printed high-efficiency silicon heterojunction solar cells metallized by silver metal complex inks on industrial G1-size (158.75 x 158.75 mm2) wafers. We demonstrate screen-printed Ag metal complex ink grid patterns with continuous fingers ~100-120 ..mu..m wide. The printed Ag grid is very thin (~1 ..mu..m), which is an order of magnitude thinner than the current ~20-30 ..mu..m fingers printed with low-temperature nanoparticle-based pastes. Double printing allows silicon heterojunction devices with efficiencies >20%. This is the highest efficiency so far, to our knowledge, of industrial solar cell precursors using this metallization technology. Simulation results suggested that increasing the thickness of the metal film does not significantly improve efficiency due to the dense, highly conductive films. So, a single print of ~1 ..mu..m finger would be enough to produce cells that perform similarly to a ~20 ..mu..m thick nanoparticle paste printed cells. Additionally, solar cells printed on G1 wafers with silver metal complex ink required more than 10 times less silver (~0.03 g) compared to those using silver/copper nanoparticle paste (~0.4 g of Ag). These results indicate that metal complex inks are a very promising replacement for silver nanoparticle pastes for industrial-scale metallization in an age of resource scarcity and high costs of noble metals.

14 SOLAR ENERGY↗
DOE OSTI2022

High Seebeck Coefficient from Screen-Printed Colloidal PbSe Nanocrystals Thin Film

Thin-film thermoelectrics (TEs) with a thickness of a few microns present an attractive opportunity to power the internet of things (IoT). Here, we propose screen printing as an industry-relevant technology to fabricate TE thin films from colloidal PbSe quantum dots (QDs). Monodisperse 13 nm-sized PbSe QDs with spherical morphology were synthesized through a straightforward heating-up method. The cubic-phase PbSe QDs with homogeneous chemical composition allowed the formulation of a novel ink to fabricate 2 μm-thick thin films through robust screen printing followed by rapid annealing. A maximum Seebeck coefficient of 561 μV K -1 was obtained at 143 °C and the highest electrical conductivity of 123 S m -1 was reached at 197 °C. Power factor calculations resulted in a maximum value of 2.47 × 10 -5 W m -1 K -2 at 143 °C. To the best of our knowledge, the observed Seebeck coefficient value is the highest reported for TE thin films fabricated by screen printing. Thus, this study highlights that increased Seebeck coefficients can be obtained by using QD building blocks owing to quantum confinement.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Organic Nano-Junctions: Linking Nanomorphology and Charge Transport in Organic Semiconductor Nanoparticles for Organic Photovoltaic Devices

In this study, innovative nanoscale devices are developed to investigate the charge transport in organic semiconductor nanoparticles. Using different steps of lithography techniques and dielectrophoresis, planar organic nano-junctions are fabricated from which hole mobilities are extracted in a space charge-limited current regime. Subsequently, these devices are used to investigate the impact of the composition and morphology of organic semiconductor nanoparticles on the charge mobilities. Pure donor nanoparticles and composite donor:acceptor nanoparticles with different donor compositions in their shell are inserted in the nanogap electrode to form the nano-junctions. The results highlight that the hole mobilities in the composite nanoparticles decrease by two-fold compared to pure donor nanoparticles. However, no significant change between the two kinds of composite nanoparticle morphologies is observed, indicating that conduction pathways for the holes are as efficient for donor proportion in the shell from 40% to 60%. Organic photovoltaic (OPV) devices are fabricated from water-based colloidal inks containing the two composite nanoparticles (P3HT:eh-IDTBR and P3HT:o-IDTBR) and no significant change in the performances is observed in accordance with the mobility results. Through this study, the performance of OPV devices have been successfully correlated to the transport properties of nanoparticles having different morphology via innovative nanoscale devices.

42 ENGINEERING↗
DOE OSTI2025

Autonomous Aerosol and Plasma Co‐Jet Printing of Metallic Devices at Ambient Temperature

Abstract Additive manufacturing of metallic materials holds the potential to revolutionize the fabrication of functional devices unattainable via traditional methods. Despite recent advancements, printing metallic materials typically requires thermal processing at elevated temperatures to form dense structures with desired properties, which presents a major challenge for direct printing and integration with temperature‐sensitive materials. Herein, a unique co‐jet printing (CJP) method is reported integrating an aerosol jet and a non‐thermal, atmospheric pressure plasma jet to enable concurrent aerosol deposition of metal nanoparticle inks and in situ sintering at ambient temperature. A machine learning algorithm is integrated with the CJP to perform real‐time defect detection and autonomous correction, enhancing the yield of printed films with high electrical conductivity from 44% to 94%. Concurrent printing and sintering eliminate the need for post‐printing processing, reducing the overall manufacturing time by multiple folds depending on product size. CJP enables direct printing of functional devices on a variety of temperature‐sensitive materials including biological materials. Direct printing of hydration sensors on living plant leaves is demonstrated for long‐duration monitoring of hydration level in the plant. The versatile CJP method opens tremendous opportunities to harmoniously integrate abiotic and biotic materials for emerging applications in wearable/implantable devices and biohybrid systems.

Du, Yipu [Department of Aerospace and Mechanical E↗
DOE OSTI2021

Assessment of task‐based performance from five clinical DBT systems using an anthropomorphic breast phantom

Purpose Digital breast tomosynthesis (DBT) is a limited‐angle tomographic breast imaging modality that can be used for breast cancer screening in conjunction with full‐field digital mammography (FFDM) or synthetic mammography (SM). Currently, there are five commercial DBT systems that have been approved by the U.S. FDA for breast cancer screening, all varying greatly in design and imaging protocol. Because the systems are different in technical specifications, there is a need for a quantitative approach for assessing them. In this study, the DBT systems are assessed using a novel methodology with an inkjet‐printed anthropomorphic phantom and four alternative forced choice (4AFC) study scheme. Method A breast phantom was fabricated using inkjet printing and parchment paper. The phantom contained 5‐mm spiculated masses fabricated with potassium iodide (KI)‐doped ink and microcalcifications (MCs) made with calcium hydroxyapatite. Images of the phantom were acquired on all five systems with DBT, FFDM, and SM modalities where available using beam settings under automatic exposure control. A 4AFC study was conducted to assess reader performance with each signal under each modality. Statistical analysis was performed on the data to determine proportion correct (PC), standard deviations, and levels of significance. Results For masses, overall detection was highest with DBT. The difference in PC was statistically significant between DBT and SM for most systems. A relationship was observed between increasing PC and greater gantry span. For MCs, performance was highest with DBT and FFDM compared to SM. The difference between PC of DBT and PC of SM was statistically significant for all manufacturers. Conclusions This methodology represents a novel approach for evaluating systems. This study is the first of its kind to use an inkjet‐printed anthropomorphic phantom with realistic signals to assess performance of clinical DBT imaging systems.

Ikejimba, Lynda C.↗
DOE OSTI2025

PFSA-Ionomer Dispersions to Thin-Films: Interplay Between Sidechain Chemistry and Dispersion Solvent

In fuel-cell catalyst layers (CLs), ionomers exists as nanoscale thin-films binding catalyst particles, wherein ionic and gaseous species transport to catalyst sites. To improve film function, ionomers have been designed based on the prototypical perfluorosulfonic acid (PFSA). Since CLs are fabricated through solution-based processing of inks, understanding how ink/dispersion solvent impacts ionomer interactions and function is important to guide future ionomer design. Herein, PFSA and its chemical derivatives are characterized from dispersion (in solvent) to thin film (cast on support) to investigate the impact of solvent water content on ionomer dispersion (structure, acidity) and resulting film properties. Dispersion characterization reveals that secondary aggregate structure depends on the sidechain chemistry, but all PFSA-based ionomers evolve similarly as dispersion becomes water-rich. The differences in aggregation alter ionomer adsorption and thin film morphology. Further, hydrophilic domain spacing and orientation are affected primarily by sidechain chemistry, and modulated by solvent composition. Thin-film conductivity correlates with hydration and nanodomain alignment, signifying the role of morphology in properties. Overall, this work provides insights into how chemistry can be used to coarse-tune structure–property relationships, while processing solvent is for fine-tuning of dispersion-film interplay for controlling CL-ionomer function, which can be translated to other chemistries and ink formulations.

25 ENERGY STORAGE↗
DOE OSTI2025

Embedded 3D printing of isotropically enhanced lattice structure with programmable elasticity via three-dimensional fiber alignment

Engineered composites with fiber orientation in a complete three-dimensional (3D) context are highly desired for maximizing structural performance as they mimic the well-organized fiber arrangement in natural composites. However, most fabrication techniques lack the capability for through-plane (z-axis) alignment, limiting the possibility for structural design and performance optimization. In this study, we present an embedded 3D printing approach that enables complete 3D fiber alignment, including region-specific alignment control along the through-plane direction. Our method utilizes the extrusion and suspension of composite inks within a supporting matrix. By regionally adjusting the ink extrusion rate and nozzle translation rate, we locally manipulated the fiber arrangement within the composite 3D architecture. Here, we demonstrate that the 3D alignment of carbon fibers in a structural composite significantly enhances both mechanical properties and thermal conductivity in the in-plane and through-plane directions. Furthermore, by strategically arranging regional fiber orientations within micro-architected materials, we fabricated metamaterial engineered composites with programmable anisotropy ratio and directional moduli.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Current challenges and potential directions towards precision microscale additive manufacturing – Part III: Energy induced deposition and hybrid electrochemical processes

The Part III of the four-part series of articles discusses the challenges and opportunities in microscale additive manufacturing processes, specifically focusing on energy-induced deposition and electrochemical processes. Compared to the direct ink write (DIW) and laser-based processes, the energy-induced deposition methods can fabricate high-resolution, high aspect ratio and complex parts, while the hybrid electrochemical process can be used to fabricate complex parts using a wide range of conductive and photoactive materials. However, the volumetric throughput of these processes is lower than their DIW and laser-based counterparts. The processes that have been explored in this process are Focused-ion Beam Induced Deposition (FIBID), Laser Chemical Vapor Deposition (LCVD), Menicus-confined Electrodeposition (MCED) and Laser-Enabled Electrochemical Printing (LECP). The range of processable materials, feature-size resolution, geometry and volumetric throughput are used as factors to evaluate the current state-of-the-art for these processes. Finally, novel approaches have been proposed in the article to address these challenges associated with microscale AM processes.

42 ENGINEERING↗
DOE OSTI2025

Tunable 3D Aerosol Jet Printing of Low‐Power Redox‐Gated Transistors with Multicomponent Inks

Printed hybrid electronics (PHE) offer a promising alternative for microelectronics fabrication, addressing some limitations of traditional subtractive manufacturing. Despite the versatility of PHE, particularly in the customization of printing inks, these devices have not yet matched the performance of silicon-based electronics due to challenges in gating mechanisms and operational stability. However, the potential of low-voltage redox-gating to achieve significant carrier modulations in correlated metal oxides remains unexplored in PHE. This study systematically investigates vanadium dioxide (VO 2 ) nanoparticles and redox inks, linking their organization in solution to their morphology, phase state, and properties in solid films and multilayered structures. Using an aerosol jet printer (AJP), a solid-state VO 2 transistor is fabricated, operating at just 0.4 V gating voltage. The printed VO 2 films demonstrate redox-modulated conductivity and consistent transistor behavior. The solid-state redox gating materials also provide long-term stability, with the device maintaining performance over 6000 cycles without degradation. These results highlight the potential of redox gating to enhance the application of functional nanoparticles in printed hybrid microelectronics, especially for flexible, low-voltage, and energy-efficient devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Review on Progress, Challenges, and Prospects of Material Jetting of Copper and Tungsten

Copper (Cu) and tungsten (W) possess exceptional electrical and thermal conductivity properties, making them suitable candidates for applications such as interconnects and thermal conductivity enhancements. Solution-based additive manufacturing (SBAM) offers unique advantages, including patterning capabilities, cost-effectiveness, and scalability among the various methods for manufacturing Cu and W-based films and structures. In particular, SBAM material jetting techniques, such as inkjet printing (IJP), direct ink writing (DIW), and aerosol jet printing (AJP), present a promising approach for design freedom, low material wastes, and versatility as either stand-alone printers or integrated with powder bed-based metal additive manufacturing (MAM). Thus, this review summarizes recent advancements in solution-processed Cu and W, focusing on IJP, DIW, and AJP techniques. The discussion encompasses general aspects, current status, challenges, and recent research highlights. Furthermore, this paper addresses integrating material jetting techniques with powder bed-based MAM to fabricate functional alloys and multi-material structures. Finally, the factors influencing large-scale fabrication and potential prospects in this area are explored.

36 MATERIALS SCIENCE↗