Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “carbon coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Effect of mission cycling on the fatigue performance of SiC-coated carbon-carbon composites

The effects of thermal and pressure cycling on the fatigue performance of carbon-carbon composites, and the influence of mission cycling on these effects, were investigated by subjecting both virgin and mission-cycled two-dimensional specimens of SiC-coated carbon-carbon composites to fatigue tests, conducted at room temperature in three-point bending, with a stress ratio of 0.2 and a frequency of 1 Hz. It was found that the fatigue strength of C-C composites is high (about 90 percent of the ultimate flexural strength), but decreased with the mission cycling. The lowering of the fatigue strength with mission cycling is attributed to the increase in interfacial bond strength due to thermal and pressure cycling of the material. The already high sensitivity of C-C composites to stress during cyclic loading increases further with the amount of mission cycling. Results of NDE suggest that the damage growth in virgin C-C, in the high-cycle range, is slow at the initial stage of the cyclic life, but propagates rapidly after certain threshold cycles of the fatigue life.

Mahfuz, H.↗
NASA NTRS1984

Binder for Carbon-Fiber Coating

Insoluble, even coating formed by soaking in polyacrylic acid. Carbon fiber material prepared by soaking in solution of 20 percent polyacrylic acid in water. Material blotted and dried at 120 degrees C for at least 2 hours. Dried material reacted with boiling aqueous solution of calcium acetate. Treated material removed from boiling solution, blotted, dried at 120 degrees C, washed with distilled water, and dried again.

Dowler, W. L.↗
NASA NTRS2022

Development of an Effective Finite-rate Oxidation Model for NuSil-coated Charred Carbon Preform Ablators

Recently, a detailed effective finite-rate surface chemistry model was developed for the oxidation of FiberForm [1] using the molecular beam experimental data of Poovathingal et al., [2]. FiberForm is the major building block of the thermal protection system (TPS) material Phenolic Impregnated Carbon Ablator (PICA), commonly used by NASA. The surface chemistry model consists of detailed surface reaction mechanisms such as adsorption, desorption, and several types of Langmuir-Hinshelwood (LH) reactions to characterize the oxygen-carbon interactions at the surface. This model provides excellent agreement with the experimental data for oxidation product compositions and corresponding translational energy distributions. Further, an effective oxidation model was constructed that captures the equivalent interaction of oxygen inside the microstructure (including multiple surface collisions) via a modified reactivity for a smooth wall boundary condition. This enables the use of this model directly into Computational Fluid Dynamics (CFD) codes and Material Response (MR) codes to accurately simulate the gas–surface interactions within FiberForm without using the detailed micro-structure. However, this effective model is valid only for the virgin FiberForm. As the TPS material undergoes ablation, the preform carbon burns and turns into char. In addition, PICA is also coated with a protective silicon coating called NuSil for the purpose of mitigating the spread of phenolic dust, and limit contamination during clean room operations. Fig. 1 shows a X-ray microtomography image of a charred NuSil-coated PICA. The NuSil layer introduces species containing silicon into the product mixture. Further, the reactivity of the carbon within the char layer is different from the virgin FiberForm as shown in Fig. 2. Recently a new set of molecular beam experiments were performed on this NuSil-coated TPS material [3] with the same type of oxygen beam used in the previous experiments. Using the latest experimental data, the previously developed effective model will be extended to account for the charred carbon as well as the NuSil coating. Finally, this new effective model with three phases – preform carbon, char, and NuSil; will be compared and validated against the experimental product compositions.

K Swaminathan Gopalan↗
NASA NTRSDate not supplied

Carbide Coated Carbon-Carbon Heat Exchange Tubes for Nuclear Thermal Propulsion Fuel Assembly

Nuclear Thermal Propulsion (NTP) systems are proposed for human Mars missions because of the potential for reduced round-trip transit time that decreases crew exposure to space environmental hazards. NTP enables abort scenarios not available with other systems and can also be used for expanded cis-lunar mobility and deep space exploration. Heat exchange tubes, within the nuclear fuel assembly, provide flow channels for gaseous hydrogen propellant to carry the heat released during the nuclear fission reaction out of the assembly. This paper summarizes the ongoing work at NASA Centers and contractors, led by NASA Langley Research Center to develop hermetic carbide coated carbon-carbon heat exchange tubes for the NTP fuel assembly; capable of operating at 2900 K in a high-pressure, flowing hydrogen environment.

carbon-carbon↗
DOE OSTI2021

Direct Mercury Detection in Landfill Leachate Using a Novel AuNP-Biopolymer Carbon Screen-Printed Electrode Sensor

A novel Au nanoparticle (AuNP)-biopolymer coated carbon screen-printed electrode (SPE) sensor was developed through the co-electrodeposition of Au and chitosan for mercury (Hg) ion detection. This new sensor showed successful Hg2+ detection in landfill leachate using square wave anodic stripping voltammetry (SWASV) with an optimized condition: a deposition potential of −0.6 V, deposition time of 200 s, amplitude of 25 mV, frequency of 60 Hz, and square wave step voltage of 4 mV. A noticeable peak was observed at +0.58 V associated with the stripping current of the Hg ion. The sensor exhibited a good sensitivity of ~0.09 μA/μg (~0.02 μA/nM) and a linear response over the concentration range of 10 to 100 ppb (50–500 nM). The limit of detection (LOD) was 1.69 ppb, which is significantly lower than the safety limit defined by the United States Environmental Protection Agency (USEPA). The sensor had an excellent selective response to Hg2+ in landfill leachate against other interfering cations (e.g., Zn2+, Pb2+, Cd2+, and Cu2+). Fifteen successive measurements with a stable peak current and a lower relative standard deviation (RSD = 5.1%) were recorded continuously using the AuNP-biopolymer-coated carbon SPE sensor, which showed excellent stability, sensitivity and reproducibility and consistent performance in detecting the Hg2+ ion. It also exhibited a good reliability and performance in measuring heavy metals in landfill leachate.

Hwang, Jae-Hoon (ORCID:0000000220100864)↗
NASA NTRS1988

Thermoplastic coating of carbon fibers

Now that quantities of prepreg were made on the thermoplastic coating line, they are being formed into both textile preform structures and directly into composite samples. The textile preforms include both woven and knitted structures which will be thermoformed into a finished part. In order to determine if the matrix resin is properly adhering to the fibers or if voids are being formed in the coating process, the tensile strength and modulus of these samples will be tested. The matrix uniformity of matrix distribution in these samples is also being determined using an image analyzer.

Edie, D. D.↗
DOE OSTI2021

Boride-Carbon Hybrid Technology for Ultra-Wear and Corrosive Conditions

This work discusses a study on a surface treatment for creating extremely durable low-friction, wear and corrosion-resistant surfaces for tribological components in harsh conditions. A duplex surface treatment was developed that combines the advantages of ultra-fast electrochemical boriding with those of hard tetrahedral amorphous carbon coatings. The friction and wear properties of the duplex treatment are compared to the boride-only treatment of AISI 1045 steel, while corrosion and contact fatigue behaviors of the duplex layer are compared to that of the single-layer carbon coating on low carbon steel. The duplex treatment yields wear rates as low as 6 × 10−8 mm3·N−1·m−1 and a coefficient of friction of 0.14 when tested against a steel counter face. The contact fatigue impact tests reveal that the high hardness of 1200 HV0.05 of the borided layer in the duplex treatment leads to higher resistance against indentation but is accompanied by a higher incidence of crack initiation, being in good agreement with the finite-element modeling of nanoindentation results. The duplex coatings exhibit resistance to pinhole corrosion as evidenced by a 3 h exposure to 15% HCl at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ultrahigh rate capability of manganese based olivine cathodes enabled by interfacial electron transport enhancement

In this study, manganese-based Olivine is a promising cathode candidate with high energy and low cost for Li-ion batteries (LIBs). Its rate capability and cyclability challenges still remain even with nano-size and carbon coating. Herein, an ultrahigh rate performance is achieved by introducing an affinitive conductor to enhance the interfacial electron transport of LiMn 0.7 Fe 0.3 PO 4 via Li 3 V 2 (PO 4 ) 3 . It is found that the Li 3 V 2 (PO 4 ) 3 facilitates sp 2 hybridization to form a highly conductive carbon coating during the carbonized process. The composite 0.9LiMn 0.7 -Fe 0.3 PO 4 .0.1Li 3 V 2 (PO 4 ) 3 can deliver a capacity of 90.9 mAh g -1 and power density of 11444 W kg -1 at 50 C-rate. Both in situ X-ray diffraction and conductive-atomic force microscopy are conducted to understand the synergetic effect between LiMn 0.7 Fe 0.3 PO 4 and Li 3 V 2 (PO 4 ) 3 . The results suggest that the interfacial electron transfer between LiMn 0.2 Fe 0.3 PO 4 particles and the electron conducting medium, such as binder/carbon black composite, is greatly improved so that the highly Li + conductive nature of olivine materials can be fully unleashed. This work demonstrates the importance of efficient interfacial electron transfer to the active cathode particles, and opens up a new venue for the rational design of high-energy and high-power batteries.

25 ENERGY STORAGE↗
NASA NTRS1994

Factors and processes governing the C-14 content of carbonate in desert soils

A model is presented describing the factors and processes which determine the measured C-14 ages of soil calcium carbonate. Pedogenic carbonate forms in isotopic equilium with soil CO2. Carbon dioxide in soils is a mixture of CO2 derived from two biological sources: respiration by living plant roots and respiration of microorganisms decomposing soil humus. The relative proportion of these two CO2 sources can greatly affect the initial C-14 content of pedogenic carbonate: the greater the contribution of humus-derived CO2, the greater the initial C-14 age of the carbonate mineral. For any given mixture of CO2 sources, the steady-state (14)CO2 distribution vs. soil depth can be described by a production/diffusion model. As a soil ages, the C-14 age of soil humus increases, as does the steady-state C-14 age of soil CO2 and the initial C-14 age of any pedogenic carbonate which forms. The mean C-14 age of a complete pedogenic carbonate coating or nodule will underestimate the true age of the soil carbonate. This discrepancy increases the older a soil becomes. Partial removal of outer (and younger) carbonate coatings greatly improves the relationship between measured C-14 age and true age. Although the production/diffusion model qualitatively explains the C-14 age of pedogenic carbonate vs. soil depth in many soils, other factors, such as climate change, may contribute to the observed trends, particularily in soils older than the Holocene.

Amundson, Ronald↗
DOE OSTI2025

Carbon nanotube coated metal mesh: Bridging nanoscale and macroscale

A novel hybrid structure has been developed by growing carbon nanotubes (CNTs) on a metal mesh that functions as a literally unlimitedly extendable backbone. This hybrid material structure provides a new approach of extending CNTs’ advantageous properties such as ultrahigh thermal and electrical conductivities, high sensitivity to gases, and distinctive wettability for different liquids with chemical inertness to macroscale—otherwise available only in nano- and microscales. In this feasibility work, CNTs were grown on a Type 316 stainless steel (SS) mesh by self-catalytical chemical vapor deposition (CVD) without the need of an externally added catalyst or catalyst support. For the radially aligned and entangled CNT forest on the SS mesh, the average CNT diameter is around 50 nm, while the length varies from 20 to 25 µm. High-resolution transmission electron microscopy analysis revealed the multiwall structure of the CNTs with >30 rolled-up graphitic sheets. Raman spectra of the CNTs showed a dominant G band, indicating a well-ordered graphitic nanostructure. Being highly hydrophobic with a water contact angle of ∼145° and oleophilic, the CNT-coated SS mesh could be used in fluid separation and organic contaminant removal from water. Moreover, CNTs are recognized for their exceptional thermal conductivity and the CNT-coated mesh offers a supportive structure with directly connected CNTs for efficient heat transfer. Proof of concept has been achieved for the CNT-coated mesh’s potentials as a liquid filter and an thermal interface material (TIM). Specifically, the CNT-coated mesh demonstrated the capability of capturing water from a water-organic mixture with a 100 % efficiency while allowing organic liquids to pass through the filter. Furthermore, when used as a TIM, the CNT-coated mesh reduced the interfacial thermal impedance by >30 %.

Carbon nanotubes (CNTS)↗
DOE OSTI2022

Macroscale superlubricity by a sacrificial carbon nanotube coating

Superlubricity, i.e., coefficient of friction (COF) below 0.01, was earlier limited to microscale in controlled environments in the earlier literature and more recently realized for macroscale sliding of ceramic or carbon surfaces lubricated by water or other polar fluids. However, there is lack of report of superlubricity for the most common bearing system, i.e., steel-steel contact in non-polar oil lubrication. Here, in this work, we present ultra-low COF of 0.001–0.007 by using a sacrificial coating composed of vertically-aligned carbon nanotubes (CNTs) for macroscale steel-steel sliding under minimum quantity lubrication (MQL) of a polyalphaolefin (PAO) oil in the ambient environment. Raman spectroscopy and electron microscopy analyses detected graphene-containing tribofilms on both the steel surfaces, which was produced by the fractured CNT flakes and metallic wear debris during running-in. The in situ formed graphene-graphene contact interface presumably possesses a low shear resistance leading to superlubricity. The presence of oil, despite as little as one droplet, has proven to be crucial. Such a superlubricity performance has shown good sustainability in extended testing of more than 500,000 cycles and strong ability of accommodating changes in sliding conditions. Results here demonstrate feasibility with fundamental insights for achieving ambient environment macroscale superlubricity.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Vanadium-enhanced Na 2 FePO 4 F cathodes for high-performance sodium-ion batteries

Sodium fluorophosphate Na 2 FePO 4 F holds great potential for sodium-ion batteries due to its high theoretical capacity, excellent structural stability, abundant resources, and affordability. However, its poor electronic and ionic conductivities limit its practical applications. Therefore, ion doping and carbon coating have been employed as synergistic strategies in this study to overcome these limitations. A one-step, energy-efficient solid-state method using sucrose as a carbon coating source was used to synthesize Na 2 FePO 4 F/C (NFPF/C) and its doped variant, Na 2 Fe 0.85 V 0.1 PO 4 F/C (NFVPF/C). 23 Na-MAS-NMR spectra confirm the existence of two distinct sites for sodium (Na1/Na2). The ex-situ 23 Na-MAS-NMR performed at different states-of-charge reveals the activity of only one sodium. The scanning electron microscopy findings reveal a reduction in the particle size with V-introduction, enhancing the energetic performances. NFVPF/C delivers higher specific capacity of 122 mAh g −1 compared to 116 mAh g −1 for NFPF/C at 0.1C. It also demonstrates improved cycling stability, retaining 81 % of its initial capacity after 120 cycles, in contrast to 46 % for the pristine material. The doped phase outperforms the pristine at higher current rates, delivering specific capacities of 81 and 55 mAh g −1 at 2C and 3C, respectively, compared to 35 and 17 mAh g −1 for NFPF/C.

25 ENERGY STORAGE↗
DOE OSTI2023

High‐Loaded Electrode Filaments for Additive Manufacturing of Structural Batteries

Abstract The unique capability of 3D printing to create geometric complex structures presents a promising avenue for producing 3D electrodes aimed at enhancing power and energy densities within constrained spaces, which is challenging to achieve through traditional slurry casting methods. However, despite advancements over the years, 3D‐printed batteries have faced limitations in terms of mechanical robustness to endure significant volume changes during cycling and restricted electrochemical performance due to the lack of adequate electrode feedstock development or post‐processing treatments. Herein, a high‐loaded electrode filament with ≈65 wt.% fillers, enabling the fabrication of structural electrodes with improved electrochemical performance and superior mechanical properties, is developed. Through a combination of 3D printing and post‐processing techniques, interdigitated structures with high areal‐loading density, resulting in a full cell with an enhanced areal capacity of ≈12.28 mAh cm −2 at ≈0.92 mA cm −2 is fabricated. Moreover, the structural batteries, treated through the carbonizing process, are integrated by the carbon coating generated during carbonization, exhibiting remarkable compressive properties (with a modulus of 18.5 MPa and a strength of 1.09 MPa). Overall, the findings demonstrate the promising potential of 3D printed batteries for practical applications, while showcasing the scalability and design flexibility offered by 3D printing technology.

Chemistry↗
DOE OSTI2020

Polymer-derived SiC/C/Al environmental barrier coatings on carbon steel

Carbon steel is a widely used structural material; however, it lacks corrosion resistance in water environments. An alternative approach to overcome this challenge is to implement the deposition of inherently corrosion-resistant ceramic coatings. SiC/C/Al coatings were developed at 700°C, using polycarbosilane in combination with Al and C, which were included as active and passive fillers, respectively. Here, we show that it is necessary to use Al particle sizes below 10 µm for them to function as an active filler below 900°C. Owing to their laminar microstructure, these coatings showed a cohesive delamination with an adhesion strength of 10 MPa. Results demonstrated that these coatings were able to reduce the corrosion of carbon steel in saline water by 99.7%, with corrosion rates of 38.33 mpy for carbon steel, and 0.099 and 0.155 mpy for SiC/C and SiC/C/Al (10 µm) coatings, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Effect of a Carbon Fiber Layer Between the Cathode and the Current Collector on Battery Cell Performance

Contact resistance between the cathode active material (CAM) and the Al current collector can be reduced by applying carbon coatings to the Al current collector surface. However, this process requires an additional step of carbon layer coating on the current collector, which increases both manufacturing costs and processing time. In the present work, an interlayer of continuous unsized carbon fibers aligned in one direction (CF interlayer), is introduced between the Al current collector and the NMC811 cathode during cathode deposition on the Al current collector. This single-step approach eliminates the need for the additional carbon layer coating on the current collector. Additionally, this approach removes the use of toxic solvents and insulative polymers used for making the carbon coating. The CF interlayer improves the rate capability at higher C-rates. The CF interlayer lowers the contact resistance between the cathode particles and the current collector while improving the activation energy of charge transfer. The peel test showed that the CF interlayer does not affect the adhesion strength of the cathode layer with the current collector.

25 ENERGY STORAGE↗
DOE OSTI2023

Directing High-Efficiency Na Plating with Carbon–Aluminum Junction Interfaces for Anode-Free Na Metal Batteries

Anode-free sodium metal batteries are highly promising for future energy storage but suffer from much faster cycling degradation as they are sensitive to even trace levels of irreversible side reactions. This work focuses on the most practical Al foil current collectors and systematically examined the effect of nano-sized carbon coating on improving the Na plating and stripping stability. We identified that the carbon-Al junction interface generated by carbon coating enabled more uniform Na depositing with lower overpotentials, delivering higher than 99.8% Faradaic efficiencies for a wide range of cycling currents between 0.5 and 3.0 mA cm -2 . This performance is much better than the 96.4% efficiency observed on uncoated Al foils under the same conditions, and was also confirmed under lean electrolyte and freezing electrolyte conditions, and can be attributed to the stronger interfacial binding and enhanced sodiophilic properties of the carbon-aluminum junction sites. Furthermore, these sites not only ensure uniform Na plating but also eliminates side reactions that would otherwise cause electrolyte depletion. As a result, Na-metal free full cells assembled with high capacity Na 3 V 2 (PO 4 ) 3 cathode delivered ~ 85% capacity retention for 100 cycles, higher than the 73% of retention of uncoated Al foil.

25 ENERGY STORAGE↗
DOE OSTI2024

Demystifying In Situ Pyrolysis Chemistry for High-Performance Polyanionic Cathodes in Sodium-Ion Batteries

In this article, the carbon coating strategy has emerged as an indispensable approach to improve the conductivity of polyanionic cathodes. However, owing to the complex reaction process between precursors of carbon and cathode, establishing a unified screening principle for carbonaceous precursors remains a technical challenge. Herein, we reveal that carbonaceous precursor pyrolysis chemistry undeniably influences the formation process and performance of Na 3 V 2 (PO 4 ) 3 (NVP) cathodes from in situ insights. By investigating three types of carbonaceous precursors, it is found that O/H-containing functional groups can provide more bonding sites for cathode precursors and generate a reducing atmosphere by pyrolysis, which is beneficial to the formation of polyanionic materials and a uniform carbon coating layer. Conversely, excessive pyrolysis of functional groups leads to a significant amount of gas, which is detrimental to the compactness of the carbon layer. Furthermore, the substantial presence of residual heteroatoms diminishes graphitization. In this case, it is demonstrated that carbon dots (CDs) precursors with suitable functional groups can comprehensively enhance the Na+ migration rate, reversibility, and interface stability of the cathode material. As a result, the NVP/CDs cathode displays outstanding capacity retention, maintaining 92% after 10,000 cycles at a high rate of 50 C. Altogether, these findings provide a valuable benchmark for carbon source selection for polyanionic cathodes.

25 ENERGY STORAGE↗
NASA NTRS2011

Carbon Nanotube Coatings as Used in Strain Sensors for Composite Tanks

The next generation of cryogenic fuel tanks, crew habitats and other components for future spacecraft will focus on the usc of lightweight carbon fiber composite materials. A critical issue in the design and optimization of such tanks and structures will bc in structural health monitoring, however, current strain sensors have limitations. In this study, a novel carbon nanotube thin film was applied to carbon fiber composites for structural monitoring. Applying a load using a 3-point bend test to simulate bowing of a tank wall, induced significant increases in the film's electrical resistance at small deflections. Upon release of the load, the resistance returned to its approximate start value and was reproducible over multiple tests. The results show that a carbon nanotube thin film has great potential for the health monitoring of composite structures.

Trigwell, Steve↗