Computational exploration of bio-oil blend effects on large two-stroke marine engines
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
Motivated by the need to reduce aircraft engine noise, NASA’s Bio-inspired Broadband Acoustic Absorber (“Bioliner”) is patented technology that can be developed into multifunctional structures that can absorb sound and might also transfer heat and/or carry a load. Bioliner was one of 12 technologies from federal and university labs that were selected for the FedTech Startup Studio 2021:1 National Aeronautics and Space Administration (NASA),2,3 National Institute of Standards and Technology (NIST),4 National Nuclear Security Administration (NNSA),5 and Northeastern University.6 From August to December 2021, FedTech coached teams of entrepreneurs who explored the commercial potential of the bioliner by performing customer discovery interviews. Results of that investigation supported the claim that the bioliner might have broad commercial potential, beyond aerospace use
About 40% of total U.S. energy consumption was consumed in residential and commercial buildings. Improved air-conditioning technology has by far the greatest potential impact on the electric industry compared to any other technology that uses electricity. This paper describes the development of an innovative natural gas, propane, LNG or bio-gas IC engine-driven heat pump (GHP) with desiccant dehumidification (GHP/DD). This integrated system has higher overall efficiencies than conventional equipment for space cooling, addresses both new and existing commercial buildings, and more effectively controls humidity in humid areas. Waste heat is recovered from the GHP to provide energy for regenerating the desiccant wheel and to augment heating capacity and efficiency. By combining the two technologies, an overall source COP of greater that 1.5 (hot, humid case) can be achieved by utilizing waste heat from the engine to reduce the overall energy required to regenerate the desiccant. Moreover, system modeling results show that the sensible heat ratio (SHR- sensible heat ratio) can be lowered to less 60% in a dedicated outdoor air system application with hot, humid cases.
Recent progress in metabolic engineering and synthetic biology enables the use of microorganisms for the production of chemicals (“bio-based chemicals”). Yet, it is still unclear which chemicals have the highest economic prospect. Because of this, we develop a framework for the identification of such promising ones. Specifically, we first develop a genome-scale constraintbased metabolic modeling approach, which is used to identify a candidate pool of 209 chemicals (together with the estimated yield, productivity and residence time for each) from the intersection of the High-Production-Volume (HPV) chemicals and the KEGG and MetaCyc databases. Second, we design three screening criteria based on a chemical’s profit margin, market volume and market size. The total process cost, including the downstream separation cost, is systematically incorporated into the evaluation. Third, given the three aforementioned criteria, we identify 32 products as economically promising if the maximum yields can be achieved, and 22 products if the maximum productivities can be achieved. The breakeven titer that renders zero profit margin for each product is also presented. Comparisons between extracellular and intracellular production, as well as E. coli and S. cerevisiae systems are also discussed. The proposed framework provides important guidance for future studies in the production of bio-based chemicals. It is also flexible in that the databases, yield estimations, and criteria can be modified to customize the screening.
More efficient engines enabled by better fuels derived from biomass could increase the fuel economy of the light duty (LD) fleet by 10% over current technology and planned developments. This report identifies top LD boosted spark ignition (BSI) biofuel candidates for further development and commercialization identified using a fuel property basis. The BSI merit function was used to evaluate the performance of candidate bio-blendstocks in improving engine efficiency. This report is aimed at biofuel researchers looking to better understand the efficiency implications of biofuels under development, as well as engine researchers who are interested in future biofuels with properties that enable more efficient engine design and operation.
This presentations outlines the following: 1) Points worth noting in the history of the PV industry, 2) PV benefits from standardization, 3) PV sharing reliability challenges since the 1975, 4) PV projects from an independent engineering (IE) perspective, 5) Site selection (what NOT to do), 6) PV Operations & Maintenance over time, 7) Soiling research (remove the silos), 8) Noting a few relevant PV IEC standards, and 9) PVfleets data sharing.
More efficient engines enabled by better fuels derived from biomass could increase the fuel economy of the light duty (LD) fleet by 10% over current technology and planned developments. This report identifies top LD boosted spark ignition (BSI) biofuel candidates for further development and commercialization identified using a fuel property basis. The BSI merit function was used to evaluate the performance of candidate bio-blendstocks in improving engine efficiency. This report is aimed at biofuel researchers looking to better understand the efficiency implications of biofuels under development, as well as engine researchers who are interested in future biofuels with properties that enable more efficient engine design and operation.
Microalgae hold promise for yielding a biofuel feedstock that is sustainable, carbon-neutral, distributed, and only minimally disruptive for the production of food and feed by traditional agriculture. Amongst oleaginous eukaryotic algae, the B race of Botryococcus braunii is unique in that it produces large amounts of liquid hydrocarbons of terpenoid origin. These are comparable to fossil crude oil, and are sequestered outside the cells in a communal extracellular polymeric matrix material. The biosynthetic engineering of terpenoid bio-crude production requires identification of genes and reconstruction of metabolic pathways responsible for production of both hydrocarbons and other metabolites of the alga that compete for photosynthetic carbon and energy.
The thermoelectric properties of gate-all-around silicon nanowires (Si NWs) are calculated to determine the potential for significant power factor enhancement. The Boltzmann transport equation and relaxation time approximation are employed to develop an electron transport model used to determine the field-effect mobility, electrical conductivity, Seebeck coefficient, and power factor for Si NWs with cross-sectional areas between 4 nm × 4 nm and 12 nm × 12 nm and a range of gate biases. Electrical conductivity for the gated Si NWs was much higher than that of doped Si due to the lack of ionized impurities and correspondingly greater carrier mobility. A significant increase in electrical conductivity with decreasing Si NW cross-sectional area was also observed due to a large increase in the average carrier density. For all Si NWs, the Seebeck coefficient was lower than that of doped bulk Si due to the different energy dependence between ionized impurity and phonon-mediated scattering processes. This decrease was also confirmed with Seebeck coefficient measurements of multigated Si NWs and n-type Si thin-films. Quantum confinement was also found to increase the Seebeck coefficient for <8 nm × 8 nm Si NWs and also at high charge densities. A maximum power factor of 6.8 × 10{sup −3} W m{sup −1} K{sup −2} was calculated for the 6 nm × 6 nm Si NWs with typical Si/SiO{sub 2} interface roughness, which is 2–3 × those obtained experimentally for bulk Si. The power factor was also found to greatly depend on surface roughness, with a root-mean-square roughness of <0.8 nm necessary for power factor enhancement. An increase in ZT may also be possible if a low thermal conductivity can be obtained with minimal surface roughness.
In this paper, we present theoretically that the thermoelectric figure of merit for a semiconductor material with a small band gap can be significantly enhanced near the intrinsic doping regime at high temperatures via the suppression of bipolar thermal conductivity when the minority carriers are selectively blocked by heterostructure barriers. This scheme is particularly effective in nanostructured materials where the lattice thermal conductivity is lowered by increased phonon scatterings at the boundaries, so that the electronic thermal conductivity including the bipolar term is limiting the figure of merit $zT$. We show that $zT$ can be enhanced to above 3 for p-type PbTe, and above 2 for n-type PbTe at 900 K with minority carrier blocking, when the lattice thermal conductivity is as low as 0.3 W/m K.
The mechanism responsible for efficiency droop in InGaN light-emitting diodes (LEDs) has long been elusive due to indirect measurement techniques used for its identification. Auger recombination is unique among proposed efficiency droop mechanisms, in that it is the only mechanism capable of generating hot carriers. In a previous study [J. Iveland et al., Phys. Rev. Lett. 110, 177406 (2013)], we performed electron energy analysis of electrons emitted into vacuum from a forward biased InGaN LED that had been brought into negative electron affinity by cesiation. Three peaks were observed in the energy spectrum of vacuum emitted electrons. In this Letter, we unambiguously identify the origin of the peaks. The two higher energy peaks correspond to accumulation of electrons transported to the surface in the bulk Γ and side L conduction band valleys. The L-valley peak is a direct signature of a hot Auger electron population. The lower energy peak results from surface photoemission induced by the internal LED light emitted from the InGaN quantum wells. Two control experiments were performed. In the first, a simple GaN pn junction generated only a single Γ peak in electroemission. In the second, selective detection of the photoemission from an LED under modulated light excitation and DC electrical injection confirms that only the low energy peak is photogenerated and that LED light is incapable of generating Γ or L-valley peaks, the latter only occurring due to the Auger effect in the LED active region.
We demonstrate InGaN/GaN multiple quantum well solar cells grown by metalorganic chemical vapor deposition on a bulk (0001) substrate with high-performance broadband optical coatings to improve light absorption. A front-side anti-reflective coating and a back-side dichroic mirror were designed to minimize front surface reflections across a broad spectral range and maximize rear surface reflections only in the spectral range absorbed by the InGaN, making the cells suitable for multijunction solar cell integration. Application of optical coatings increased the peak external quantum efficiency by 56% (relative) and conversion efficiency by 37.5% (relative) under 1 sun AM0 equivalent illumination.
Abstract Chloroplast biotechnology is a route for novel crop metabolic engineering. The potential bio-confinement of transgenes, the high protein expression and the possibility to organize genes into operons represent considerable advantages that make chloroplasts valuable targets in agricultural biotechnology. In the last 3 decades, chloroplast genomes from a few economically important crops have been successfully transformed. The main bottlenecks that prevent efficient transformation in a greater number of crops include the dearth of proven selectable marker gene-selection combinations and tissue culture methods for efficient regeneration of transplastomic plants. The prospects of increasing organelle size are attractive from several perspectives, including an increase in the surface area of potential targets. As a proof-of-concept, we generated Solanum tuberosum (potato) macro-chloroplast lines overexpressing the tubulin-like GTPase protein gene FtsZ1 from Arabidopsis thaliana . Macro-chloroplast lines exhibited delayed growth at anthesis; however, at the time of harvest there was no significant difference in height between macro-chloroplast and wild-type lines. Macro-chloroplasts were successfully transformed by biolistic DNA-delivery and efficiently regenerated into homoplasmic transplastomic lines. We also demonstrated that macro-chloroplasts accumulate the same amount of heterologous protein than wild-type organelles, confirming efficient usage in plastid engineering. Advantages and limitations of using enlarge compartments in chloroplast biotechnology are discussed.
Global demand for transportation fuels is projected to increase 40% by 2040, and biomass-derived fuels (biofuels) play a crucial role in substituting fossil fuels and mitigating greenhouse gas emissions. Currently, biofuels are mainly consumed as blendstocks combined with petroleum-based fuels, and effective conversion technologies can address the quality challenges for offering standalone biofuels. Thermochemical conversion process is one of the most promising pathways among existing technologies for biofuel production. However, the major barriers are unwanted characteristics (e.g., thermal instability) of intermediate products, such as bio-oil, and required upgrading treatments for producing compatible fuels. Here, this study highlights the merits and critical challenges of thermochemical conversion and physicochemical upgrading technologies for bio-blendstock production from lignocellulosic biomass. The novelty of this study lies in potential directions for future research through both critical and systematic literature reviews, and the proposed intensified process for lignocellulosic-based fuel blendstocks production. It is concluded that recovery and fractionation strategies (e.g., quenching and stripping) can maximize process yields and add values in the efficient conversion pathways. Effective quenching can stop secondary free radical reactions and improve liquid yields over gas and solid yields. Stripping process can improve process yield, catalyst lifespan, and thermal stability. It is further concluded that physicochemical treatments are not as effective as thermochemical treatments, but have advantages of mild operating conditions and potential for integrated solutions in conjunction with other treatments.
MEMS based micro heaters are a key component in micro bio-calorimetry, nondispersive infrared gas sensors, semiconductor gas sensors and microfluidic actuators. A micro heater with a uniform temperature distribution in the heating area and short response time is desirable in ultrasensitive temperature-dependent measurements. In this study, we propose a novel micro heater design to reach a uniform temperature in a large heating area by optimizing the heating power density distribution in the heating area. A polyimide membrane is utilized as the substrate to reduce the thermal mass and heat loss which allows for fast thermal response as well as a simplified fabrication process. A gold and titanium heating element is fabricated on the flexible polyimide substrate using the standard MEMS technique. The temperature distribution in the heating area for a certain power input is measured by an IR camera, and is consistent with FEA simulation results. Finally, this design can achieve fast response and uniform temperature distribution, which is quite suitable for the programmable heating such as impulse and step driving.
Explore the source record for details and available documents.
This manuscript describes a simple and rapid method for fabricating free-standing structures composed primarily (>94% w/w, and 55–80 at%) of noble metals (e.g., gold, silver, platinum, etc.) and having physical morphologies that resemble paper, thread, or fabric. In this method, templates (i.e., pieces of paper, or cotton fabric) are loaded with aqueous solutions of salts of noble metals, and then the cellulosic component is burned off in a furnace held at high temperatures (i.e., from 550 °C to 800 °C, depending on the procedure, in air). Even though the environment in a furnace is ostensibly oxidizing (e.g., hot air), the metal ions are reduced to elemental metal and form paper-templated or fabric-templated structures that have morphologies similar to that of the material from which they were derived (i.e., paper or fabric). Paper-templated structures are fibrous, permeable to gases and liquides, electrically conductive, and in some cases (e.g., paper-templated gold and paper-templated platinum structures), their surfaces are electroactive. The surface areas of paper-templated structures are more than 20 times higher than their projected areas. Finally, paper-templated structures thus have properties that make them potentially useful in catalysis, sensing, and electroanalysis.