Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “back contact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Thin film CZTSSe photovoltaic device

A method for forming a back contact on an absorber layer in a photovoltaic device includes forming a two dimensional material on a first substrate. An absorber layer including Cu—Zn—Sn—S(Se) (CZTSSe) is grown over the first substrate on the two dimensional material. A buffer layer is grown on the absorber layer on a side opposite the two dimensional material. The absorber layer is exfoliated from the two dimensional material to remove the first substrate from a backside of the absorber layer opposite the buffer layer. A back contact is deposited on the absorber layer.

14 SOLAR ENERGY↗
DOE OSTI2023

Degradation behavior of CIGS solar Cells: A parametric analysis

A parametric study of the effect of bulk and interface properties on device characteristics as a function of heat and light stress under open-circuit and short-circuit conditions is developed for Cu(In,Ga)(S,Se) 2 solar cells using SCAPS-1D simulator. The variables and interdependencies modeled include: (1) conduction band offset (CBO) between buffer and absorber; (2) buffer ionized donor density; (3) CIGS shallow acceptor density; (4) CIGS deep acceptor density; (5) CIGS shallow donor density; (6) ionized acceptor concentration in the ordered vacancy compound (OVC) CIGS/buffer interface; and (7) back contact work-function. An increase in absorber shallow acceptor or a decrease in shallow donor density results in an increase in net carrier density and open-circuit voltage (V OC ). Further, a decrease in V OC is observed with an increase in the deep acceptors or neutral midgap defects in the CIGS due to higher charge carrier recombination. A change of CBO from spike to cliff condition is a dominant mechanism of decreasing VOC with an interface defect density of 10 12 cm -2 . The minimum depletion width is found to be specifically sensitive to CBO and interface defect density. An inflection in the capacitance–voltage curves (in reverse bias) is observed with simultaneous increase in bulk deep acceptor density and shallow donor density near the back contact.

14 SOLAR ENERGY↗
DOE OSTI2022

Effect of oxide layer growth conditions on radiation detection performance of Ni/SiO 2 /epi-4H-SiC MOS capacitors

We report high resolution radiation detection has been demonstrated using Ni/SiO2/n-4H-SiC metal-oxidesemiconductor vertical capacitors fabricated using highly crystalline 4H-SiC epilayers. The oxide layers have been grown thermally using two different approaches: i) in-air, and ii) oxygen-ambience oxidation. The devices fabricated using the former method exhibited dark currents one order of magnitude higher than that in the latter. The observed difference has been attributed to the back-contact series resistance and capacitance. Regardless of the difference in the device parameters, detectors prepared using both of the methods exhibited very high energy resolutions of ≤ 0.5% for 5486 keV alpha particles emitted by an 241Am radioisotope. Capacitance mode deep level transient spectroscopic (DLTS) studies revealed similar type of electrically active defects along with Z1/2 and EH5 deep level defects in both the types of devices. The DLTS scans also revealed positive polarity peaks in these devices which indicate emission from minority carrier trap centers. The activation energy corresponding to the peak was found to be ~1.2 eV which has been assigned to HK3 defects responsible for hole trapping in 4H-SiC. The possibility of appearance of the positive peak due to non-negligible impedance of the back-contact has been ruled out based on the observation that the centroid of the observed peak did not change with detectors having different device parameters.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Investigation of Proposed Process Sequence for the Array Automated Assembly Task, Phase 2

The technological readiness of the proposed process sequence was reviewed. Process steps evaluated include: (1) plasma etching to establish a standard surface; (2) forming junctions by diffusion from an N-type polymeric spray-on source; (3) forming a p+ back contact by firing a screen printed aluminum paste; (4) forming screen printed front contacts after cleaning the back aluminum and removing the diffusion oxide; (5) cleaning the junction by a laser scribe operation; (6) forming an antireflection coating by baking a polymeric spray-on film; (7) ultrasonically tin padding the cells; and (8) assembling cell strings into solar circuits using ethylene vinyl acetate as an encapsulant and laminating medium.

Mardesich, N.↗
NASA NTRS1980

Screen printing technology applied to silicon solar cell fabrication

The process for producing space qualified solar cells in both the conventional and wraparound configuration using screen printing techniques was investigated. Process modifications were chosen that could be easily automated or mechanized. Work was accomplished to optimize the tradeoffs associated with gridline spacing, gridline definition and junction depth. An extensive search for possible front contact metallization was completed. The back surface field structures along with the screen printed back contacts were optimized to produce open circuit voltages of at least an average of 600 millivolts. After all intended modifications on the process sequence were accomplished, the cells were exhaustively tested. Electrical tests at AMO and 28 C were made before and after boiling water immersion, thermal shock, and storage under conditions of high temperature and high humidity.

Thornhill, J. W.↗
NASA NTRS1979

The NASA Lewis Research Center program in space solar cell research and technology

Progress in space solar cell research and technology is reported. An 18 percent-AMO-efficient silicon solar cell, reduction in the radiation damage suffered by silicon solar cells in space, and high efficiency wrap-around contact and thin (50 micrometer) coplanar back contact silicon cells are among the topics discussed. Reduction in the cost of silicon cells for space use, cost effective GaAs solar cells, the feasibility of 30 percent AMO solar energy conversion, and reliable encapsulants for space blankets are also considered.

Brandhorst, H. W., Jr.↗
DOE OSTI2020

Effects of post-deposition CdCl 2 annealing on electronic properties of CdTe solar cells

The effects of post-deposition CdCl 2 annealing temperature on the electronic properties of CdTe solar cells were investigated. CdTe devices incorporate Mg doped ZnO as a buffer layer and selenization using a CdSe interlayer for reducing the buffer/absorber interface recombination and increasing solar energy absorption respectively. The post-deposition CdCl 2 annealing treatments were done under separate, inert atmospheres of nitrogen and helium across the temperature range 380 to 430 °C. Electrical characterization of devices is carried out including temperature dependent current-voltage characteristics, admittance spectroscopy, and Shockley-Read-Hall recombination analysis. Here, the best improvements in device efficiency are obtained upon annealing at temperature 410 °C. This anneal correlated with reduced back contact barrier in CdTe and reduced grain-boundary barrier height which is beneficial for enhanced charge transport.

14 SOLAR ENERGY↗
DOE OSTI2026

Collaborative R&D with REEL Solar Inc (REEL) to Understand and Overcome Performance Limitations in CdTe Solar Cells: Cooperative Research and Development (Final Report)

This CRADA will focus on processing, advanced characterization, and testing of photovoltaic materials and devices to understand and improve REEL CdTe solar technology. This will include examining process variations and different buffer, absorber, and contact layers from REEL and NLR to maximize performance. The unique and diverse advanced characterization tools at NLR, such as time-resolved photoluminescence, capacitance-voltage measurements, electron beam scattered diffraction, cathodoluminescence, electron microscopy, TOF-SIMS, and other measurements will be applied to characterize REEL processing to improve understanding and guide experimental directions. Accelerated stability and potential induced degradation tests will be used to analyze metastability, short-and-long term degradation, and improve bankability. A second and major thrust this period will be joint development of Si/CdTe tandem solar cells to overcome industry wide terrestrial solar efficiency limits with the two lowest cost and manufacturable solar materials today. This will include developing novel transparent back contacts that can be incorporated into tandem structures and other novel solar applications, detailed analysis of designs and configurations for CdTe/Si tandem modules, and prototyping REEL CdTe Technology with Si bottom cells in tandem structures.

14 SOLAR ENERGY↗
DOE OSTI2024

Four–Terminal Perovskite–CdSeTe Tandem Solar Cells: From 25% toward 30% Power Conversion Efficiency and Beyond

Thin-film tandem photovoltaic (PV) technology has emerged as a promising avenue to enhance power conversion efficiency beyond the radiative efficiency limit of single-junction devices. Combining a tunable wide-bandgap perovskite cell with a commercially established narrow-bandgap cadmium selenium telluride (CdSeTe) cell in a comparatively easy-to-fabricate four-terminal (4-T) arrangement is a great step in that direction. Herein, the impact of the transparent back contact and the perovskite absorber bandgap on the performance of 4-T perovskite–CdSeTe tandem solar cells is investigated. 4-T perovskite–CdSeTe tandem device architecture with ≈25% efficiency is demonstrated and a feasible pathway is shown to improve the tandem efficiency to more than 30%. Furthermore, the results show that the integration of CdSeTe with perovskite in 4-T tandem PV configurations represents a significant advancement toward achieving higher efficiency and low-cost tandem PVs.

14 SOLAR ENERGY↗
DOE OSTI2021

Effect of Dopant Compensation on the Conductivity of the Intrinsic poly-Si Isolation Region in Passivated IBC Silicon Solar Cells

The performance of IBC solar cells depends on the ability of this region to electrically isolate the doped fingers so that shunting does not occur and reduce the cell fill factor. We report on simulations which model the region between the p- and n-type poly-Si fingers of interdigitated back contact (IBC) solar cells as a series of resistors extending from one doped finger to the other. We demonstrate that the existence of a well compensated region between the doped fingers is enough to prevent shunting and loss of cell performance, despite contamination of dopants from the opposing dopant fingers. We show through these simulations that a net doping concentration below ~1018 cm-3 will enable a high resistivity and identify the conditions under which this highly resistive region forms despite imperfect finger edges. Additionally, we apply this analysis to tails measured by time-of-flight secondary ion mass spectrometry and confirm this hypothesis for our experimentally measured tails.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2022

Dopant Compensation within the Intrinsic Poly-Si Isolation Region in Poly-Si/SiOx Passivated IBC Si Solar Cells

We report on the effect of dopant compensation within intrinsic poly-Si regions between p- and n-type fingers of poly-Si/SiOx passivated interdigitated back contact (IBC) solar cells using intrinsic poly-Si as the isolation region between the doped poly-Si fingers. First, we show that dopants from the doped fingers contaminate the intrinsic gap, resulting in doping of the entire intrinsic gap and overlap of the dopant tails from each finger. Next, we show that despite this doping across the gap, shunting between the doped fingers does not occur. We show that this is a result of trap-assisted compensation creating a highly resistive intrinsic region, preventing shunt. We simulate shunt resistance across the gap based on local carrier concentration and deep trap density. We show that trap defects within the poly-Si enhance compensation between the dopant tails. We experimentally confirm these predictions by scanning spreading resistance microscopy of the gap showing ~20 um domain with resistivity ~10^7 ..omega.. cm. Additionally, Kelvin probe force microscopy are compared to finite element simulations which result in the same approximate shape for potential profile, indicating diode behavior across the isolation region. These results demonstrate the powerful effect that trap defects have within the poly-Si isolation region and suggest that precision patterning is not as essential as once thought.

dopant compensation↗
DOE OSTI2021

Optical and Electronic Losses Arising from Physically Mixed Interfacial Layers in Perovskite Solar Cells

Perovskite solar cell device performance is affected by optical and electronic losses. To minimize these losses in solar cells, it is important to identify their sources. Here, we report the optical and electronic losses arising from physically mixed interfacial layers between the adjacent component materials in highly efficient two terminal (2T) all-perovskite tandem, single junction wide-bandgap, and single junction narrow-bandgap perovskite-based solar cells. Physically mixed interfacial layers as the sources of optical and electronic losses are identified from spectroscopic ellipsometry measurements and data analysis followed by comparisons of simulated and measured external quantum efficiency spectra. Parasitic absorbance in the physically mixed regions between silver metal electrical contacts and electron transport layers (ETLs) near the back contact and a physical mixture of commercial indium tin oxide and hole transport layers (HTL) near the front electrical contact lead to substantial optical loss. Here, a lower-density void + perovskite nucleation layer formed during perovskite deposition at the interface between the perovskite absorber layer and the HTL causes electronic losses due to incomplete collection of photogenerated carriers likely originating from poor coverage and passivation of the initially nucleating grains.

14 SOLAR ENERGY↗
NASA NTRS1972

A reliable all-silver front contact for silicon solar cells

The feasibility of making an adherent and moisture degradation resistant silver-only front contact to silicon solar cells was demonstrated. Optimum fabrication processes and process sequences were determined for making such contacts. These contacts were found to also have good electrical characteristics. A back contact of aluminum-silver was also developed. This proved very satisfactory for low-temperature applications.

Lamneck, J. H., Jr.↗
DOE OSTI2021

Development of arsenic doped Cd(Se,Te) absorbers by MOCVD for thin film solar cells

Recent developments in CdTe solar cell technology have included the incorporation of ternary alloy Cd(Se,Te) in the devices. CdTe absorber band gap grading due to Se alloying contributes to current density enhancement and can result in device performance improvement. Here we report Cd(Se,Te) polycrystalline thin films grown by a chamberless inline atmospheric pressure metal organic chemical vapour deposition technique, with subsequent incorporation in CdTe solar cells. The compositional dependence of the crystal structure and optical properties of Cd(Se,Te) are examined. Selenium graded Cd(Se,Te)/CdTe absorber structure in devices are demonstrated using either a single CdSe layer or CdSe/Cd(Se,Te) bilayer (with or without As doping in the Cd(Se,Te) layer). Cross-sectional TEM/EDS, photoluminescence spectra and secondary ion mass spectroscopy analysis confirmed the formation of a graded Se profile toward the back contact with a diffusion length of ~1.5 um and revealed back-diffusion of Group V (As) dopants from the CdTe layer into Cd(Se,Te) grains. Due to the strong Se/Te interdiffusion, CdSe in the Se bilayer configuration was unable to form an n-type emitter layer in processed devices. In situ As doping of the Cd(Se,Te) layer benefited the device junction quality with current density reaching 28.3 mA/cm 2 . The results provide useful insights for the optimisation of Cd(Se,Te)/CdTe solar cells.

14 SOLAR ENERGY↗
NASA NTRS1972

Development of GaAs solar cells

Solar cells and mesa diodes were fabricated by the implantation of zinc or beryllium ions into n-type gallium arsenide. Annealing temperatures above 750 C (zinc) or 650 C (beryllium) were found to produce 50% to 100% activation of the implanted ions. Junction depths of about 0.4 micron were produced by 600 keV zinc implants or 70 keV beryllium implants. P-layer sheet resistance was about 150 ohms for 2 x 10 to the 15th power cm/2 zinc or 1 x 10 to the 15th power cm/2 beryllium implants. This is sufficiently low for efficient solar cell fabrication. Contacting procedures were improved to yield reproducibly adherent, low resistance front and back contacts.

Source record↗
DOE OSTI2021

Solar cell having a plurality of conductive contacts

The formation of solar cell contacts using a laser is described. A method of fabricating a back-contact solar cell includes forming a poly-crystalline material layer above a single-crystalline substrate. The method also includes forming a dielectric material stack above the poly-crystalline material layer. The method also includes forming, by laser ablation, a plurality of contacts holes in the dielectric material stack, each of the contact holes exposing a portion of the poly-crystalline material layer; and forming conductive contacts in the plurality of contact holes.

Harley, Gabriel↗
DOE OSTI2022

Evaluation of PbTe and SnTe as Ohmic Contact Layers in CdTe Solar Cell Devices

For solar cells based on CdTe, the choice of a suitable back contact material is limited by CdTe's deep work function. Here, we explored p-type PbTe and SnTe as ohmic contacts to CdTe. These contact layers were grown on single crystal CdTe substrates by molecular beam epitaxy, and the valence band offset between film and substrate was measured using X-ray photoemission spectroscopy. Polycrystalline device structures were also grown by sublimation to assess performance improvements. Doping was achieved in PbTe by thallium incorporation. Only the highest Tl doped PbTe resulted in a desirable band alignment with the CdTe, forming an electron reflector and no hole barrier. Time-resolved photoluminescence measurements also revealed significant photocarrier lifetime improvements for only the highest doped PbTe. Consequentially, devices incorporating the highest doped PbTe layers showed increased power conversion efficiency, primarily from increased fill factor. Doping of the PbTe was measured via Hall effect with variable magnetic field, which was required due to the formation of an n-type parasitic interface layer. To properly interpret the variable field Hall measurements, we derived an expression for the magnetic field-dependent conductivity tensor of an L-valley semiconductor.

anisotropic band valley↗
NASA NTRS1975

Recent advancements in low cost solar cell processing

A proof-of-concept solar cell process has been developed that is adaptable to automation. This involved the development of a new contact system, a new antireflection coating system, a drift field cell design and a new contoured surface treatment. All these processes are performed without the use of vacuum chambers and expensive masking techniques, thus providing the possibility of reduced costs by automation using conventional semiconductor processing machinery. The contacts were printed on the cells by conventional silk screen machinery. The P(+) back field was formed by diffusing in aluminum from a printed aluminum back contact. The antireflection coating was formed by spinning on and baking a TiO2-SiO2 glass film. Air-mass-zero efficiencies of over 10% were achieved using this completely vacuum-free process.

Ralph, E. L.↗