Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “apparent power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Beam steering system

A simple technique for steering the beam of a multimodule phased array MST (mesosphere, stratosphere, troposphere) radar antenna is described. It is desirable to be able to point the antenna in multiple directions, so as to derive all components of the horizontal velocity. This was done on an experimental basis by adding parallel wire line to the feed and achieving a southward tilt of the antenna. It is proved possible to steer the beam through most of the available range without adversely affecting the VSWR seen from the transmitter. Calibrating the antenna direction can be accomplished by observing radio sources, though there are an inadequate number to cover all directions. For various assumed values of the aspect sensitivity in dB/deg, and the calculated antenna pattern, it is possible to calculate the effective pointing angle of the antenna, defined as that angle which would give an identical location for the centroid of the power spectrum if aspect sensitivity were absent. Using averaged apparent steering directions, eastward and northward winds were calculated for special radar runs simultaneous with 14 balloon launches at Peoria and results are presented.

Bowhill, S. A.↗

Comet 81p/Wild 2: The Updated Stardust Coma Dust Fluence Measurement for Smaller (Sub 10-Micrometre) Particles

Micrometre and smaller scale dust within cometary comae can be observed by telescopic remote sensing spectroscopy [1] and the particle size and abundance can be measured by in situ spacecraft impact detectors [2]. Initial interpretation of the samples returned from comet 81P/Wild 2 by the Stardust spacecraft [3] appears to show that very fine dust contributes not only a small fraction of the solid mass, but is also relatively sparse [4], with a low negative power function describing grain size distribution, contrasting with an apparent abundance indicated by the on-board Dust Flux Monitor Instrument (DFMI) [5] operational during the encounter. For particles above 10 m diameter there is good correspondence between results from the DFMI and the particle size inferred from experimental calibration [6] of measured aerogel track and aluminium foil crater dimensions (as seen in Figure 4 of [4]). However, divergence between data-sets becomes apparent at smaller sizes, especially submicrometre, where the returned sample data are based upon location and measurement of tiny craters found by electron microscopy of Al foils. Here effects of detection efficiency tail-off at each search magnification can be seen in the down-scale flattening of each scale component, but are reliably compensated by sensible extrapolation between segments. There is also no evidence of malfunction in the operation of DFMI during passage through the coma (S. Green, personal comm.), so can the two data sets be reconciled?

Price, M. C.↗

Meter-wavelength VLBI. IV - Temporal and spatial scattering of the Crab Nebula pulsar's radiation

The spatial and temporal phenomena observed in the Crab Nebula pulsar's radiation are reviewed, with emphasis on the recent VLBI observations of the apparent angular size and the ratio of pulsing to total power. Three models for scattering (single thin screen, two screen, and extended medium) are discussed and shown to be deficient, under the usual assumption of a uniform scattering medium, in explaining the observed combination of temporal and angular broadening. A new model is proposed, in which the temporal broadening is dominated by scattering in the small filament which lies in the nebula in front of the pulsar, while the extended interstellar medium causes the angular broadening. This model explains the otherwise discordant angular and temporal effects and also the lack of an apparent source-size expansion with pulse phase.

Vandenberg, N. R.↗

Optimize out-of-core thermionic energy conversion for nuclear electric propulsion

Thermionic energy conversion (TEC) potentialities for nuclear electric propulsion (NEP) are examined. Considering current designs, their limitations, and risks raises critical questions about the use of TEC for NEP. Apparently a reactor cooled by hotter-than-1675 K heat pipes has good potentialities. TEC with higher temperatures and greater power densities than the currently proposed 1650 K, 5-to-6 W/sq cm version offers substantial gains. Other approaches to high-temperature electric isolation appear also promising. A high-power-density, high-temperature TEC for NEP appears, therefore, attainable. It is recommended to optimize out-of-core thermionic energy conversion for nuclear electric propulsion. Although current TEC designs for NEP seem unnecessary compared with Brayton versions, large gains are apparently possible with increased temperatures and greater power densities.

Morris, J. F.↗

Power spectra of solar convection

The properties of convective motions on the sun are studied using Kitt Peak Doppler images and power spectra of convection. The power peaks at a scale of about 29,000 km and drops off smoothly with wavenumber. There is no evidence of apparent energy excess at the scale of the mesogranulation proposed by other authors. The vertical and horizontal power for each wavenumber are obtained and used to calculate the vertical and horizontal velocities of the supergranulation. The amplitude of vertical and horizontal velocities of the supergranulation are 0.034 (+ or - 0.002) km/s and 0.38 (+ or - 0.01) km/s, respectively. The corresponding rms values are 0.024 (+ or - 0.002) km/s and 0.27 (+ or - 0.01) km/s.

Chou, D.-Y.↗

Replication of the Apparent Excess Heat Effect in a Light Water-Potassium Carbonate-Nickel Electrolytic Cell

Replication of experiments claiming to demonstrate excess heat production in light water-Ni-K2CO3 electrolytic cells was found to produce an apparent excess heat of 11 W maximum, for 60 W electrical power into the cell. Power gains range from 1.06 to 1.68. The cell was operated at four different dc current levels plus one pulsed current run at 1 Hz, 10% duty cycle. The 28 liter cell used in these verification tests was on loan from a private corporation whose own tests with similar cells are documented to produce 50 W steady excess heat for a continuous period exceeding hundreds of days. The apparent excess heat can not be readily explained either in terms of nonlinearity of the cell's thermal conductance at a low temperature differential or by thermoelectric heat pumping. However, the present data do admit efficient recombination of dissolved hydrogen-oxygen as an ordinary explanation. Calorimetry methods and heat balance calculations for the verification tests are described. Considering the large magnitude of benefit if this effect is found to be a genuine new energy source, a more thorough investigation of evolved heat in the nickel-hydrogen system in both electrolytic and gaseous loading cells remains warranted.

Niedra, Janis M.↗

From the Blazar Sequence to the Blazar Envelope: Revisiting the Relativistic Jet Dichotomy in Radio-Loud AGN

We revisit the concept of a blazar sequence that relates the synchrotron peak frequency (Vpeak) in blazars with synchrotron peak luminosity (Lpeak, in vLv) using a large sample of radio-loud AGN. We present observational evidence that the blazar sequence is formed from two populations in the synchrotron Vpeak - Lpeak plane, each forming an upper edge to an envelope of progressively misaligned blazars, and connecting to an adjacent group of radio galaxies having jets viewed at much larger angles to the line of sight. When binned by jet kinetic power (Lkin; as measured through a scaling relationship with extended radio power), we find that radio core dominance decreases with decreasing synchrotron Lpeak, revealing that sources in the envelope are generally more misaligned. We find population-based evidence of velocity gradients in jets at low kinetic powers (approximately 10(exp 42) - 10(exp 44.5) erg s(exp -1)), corresponding to FR I radio galaxies and most BL Lacs. These low jet power 'weak jet' sources, thought to exhibit radiatively inefficient accretion, are distinguished from the population of non-decelerating, low synchrotron-peaking (LSP) blazars and FR II radio galaxies ('strong' jets) which are thought to exhibit radiatively efficient accretion. The two-population interpretation explains the apparent contradiction of the existence of highly core-dominated, low-power blazars at both low and high synchrotron peak frequencies, and further implies that most intermediate synchrotron peak (ISP) sources are not intermediate in intrinsic jet power between LSP and high synchrotron-peaking (HSP) sources, but are more misaligned versions of HSP sources with similar jet powers.

Meyer, Eileen T.↗

VLBI observations of the Crab nebula pulsar

Observations were made at meter wave-lengths using very long base-line interferometry techniques. At 196.5 MHz no resolution of the pulsar are observed; all the pulse shapes observed with the interferometers are similar to single dish profiles, and all the power pulsates. At 111.5 MHz besides the pulsing power there is always a steady component, presumably due to interstellar scattering. The pulsar is slightly resolved at 111.5 MHz with an apparent angular diameter of 0.07 sec ? 0.01 sec. A 50 percent linear polarization of the time-averaged power is noted at 196.5 MHz; at 111.5 MHz, 20 percent of the total time-averaged power is polarized, 35 percent of the pulsing power is polarized, and the steady component is unpolarized.

Vandenberg, N. R.↗

Effects of display format on pilot describing function and remnant

As part of a program to develop a comprehensive theory of manual control displays, six display formats were used by three instrument-rated pilots to regulate against random disturbances with a controlled element under both foveal and 10 deg parafoveal viewing conditions. The six display formats were: CRT line, CRT thermometer bar, 14-bar quantized on a CRT, a rotary dial and pointer, and two variations of a moving scale tape-drive. All were scaled to equivalent movement and apparent brightness. Measures included overall performance, describing functions, error remnant power spectra, critical instability scores, and subjective display ratings. The results show that the main effect of display format is on the loop closure properties. Less desirable displays induce lower bandwidth closures with consequent effects on the closed-loop remnant and performance.

Jex, H. R.↗

H alpha oscillations in sunspot umbrae

Results are reported for direct measurement of intensity fluctuations and photographic subtractions of simultaneous Doppler filtergrams of H-alpha oscillations in sunspot umbrae. The observational techniques are described, and data are presented on the intensity variations, power spectra, and specific characteristics of the oscillations. Periods for the velocity oscillations are obtained by power spectrum analysis. It is found that the oscillations are apparently continuous, and that each umbra has its own characteristic period ranging from 145 to 180 plus or minus 10 sec and a duration of at least 8 cycles. A Doppler shift of 10 km/sec, an oscillating element size of 3 sec or less, and visibility to a radius vector of about 0.9 are also observed.

Phillis, G. L.↗

The IRAS galaxy 0421+040P06: An active spiral (?) galaxy with extended radio lobes

The infrared bright galaxy 0421+040P06 detected by IRAS at 25 and 60 microns was studied at optical, infrared, and radio wavelength. It is a luminous galaxy with apparent spiral structure emitting 4 x 10 to the 37th power from far-infrared to optical wavelengths. Optical spectroscopy reveals a Seyfert 2 emission line spectrum, making 0421+040P06 the first active galaxy selected from an unbiased infrared survey of galaxies. The fact that this galaxy shows a flatter energy distribution with more 25 micron emission than other galaxies in the infrared sample may be related to the presence of an intense active nucleus. The radio observations reveal the presence of a non-thermal source that, at 6 cm, shows a prominent double lobed structure 20 to 30 kpc in size extending beyond the optical confines of the galaxy. The radio source is three to ten times larger than structures previously seen in spiral galaxies.

Beichman, C. A.↗

The IRAS galaxy 0421 + 040P06 - An active spiral (?) galaxy with extended radio lobes

The infrared bright galaxy 0421 + 040P06 detected by IRAS at 25 and 60 microns was studied at optical, infrared, and radio wavelength. It is a luminous galaxy with apparent spiral structure emitting 4 x 10 to the 37th power from far-infrared to optical wavelengths. Optical spectroscopy reveals a Seyfert 2 emission line spectrum, making 0421 + 040P06 the first active galaxy selected from an unbiased infrared survey of galaxies. The fact that this galaxy shows a flatter energy distribution with more 25 micron emission than other galaxies in the infrared sample may be related to the presence of an intense active nucleus. The radio observations reveal the presence of a non-thermal source that, at 6 cm, shows a prominent double lobed structure 20 to 30 kpc in size extending beyond the optical confines of the galaxy. The radio source is three to ten times larger than structures previously seen in spiral galaxies.

Beichman, C.↗

The Impact of Microtechnology on Space System Development

Microtechnology has the potential for a beneficial impact on both launch and space flight operations because of savings in mass, power consumption, volume and low cost manufacturing and testing. Less apparent, but equally valuable, are the advantages in reliability to be gained by increased redundancy and the reduction of complexity in the fabrication process. However, a successful program for the development and insertion of these technologies will need to consider the conservatism of the aerospace community. This is more true of government space programs where success is measured by a lack of launch failures and less true of commercial ventures where success may be measured by other criteria. This paper presents a strategy for evolving microtechnology in space systems that fits both the government's risk avoidance culture, and parallels the expected development of microtechnology applications in space systems.

Sutton, David G.↗

Visual Orientation in Unfamiliar Gravito-Inertial Environments

The goal of this project is to better understand the process of spatial orientation and navigation in unfamiliar gravito-inertial environments, and ultimately to use this new information to develop effective countermeasures against the orientation and navigation problems experienced by astronauts. How do we know our location, orientation, and motion of our body with respect to the external environment ? On earth, gravity provides a convenient "down" cue. Large body rotations normally occur only in a horizontal plane. In space, the gravitational down cue is absent. When astronauts roll or pitch upside down, they must recognize where things are around them by a process of mental rotation which involves three dimensions, rather than just one. While working in unfamiliar situations they occasionally misinterpret visual cues and experience striking "visual reorientation illusions" (VRIs), in which the walls, ceiling, and floors of the spacecraft exchange subjective identities. VRIs cause disorientation, reaching errors, trigger attacks of space motion sickness, and potentially complicate emergency escape. MIR crewmembers report that 3D relationships between modules - particularly those with different visual verticals - are difficult to visualize, and so navigating through the node that connects them is not instinctive. Crew members learn routes, but their apparent lack of survey knowledge is a concern should fire, power loss, or depressurization limit visibility. Anecdotally, experience in mockups, parabolic flight, neutral buoyancy and virtual reality (VR) simulators helps. However, no techniques have been developed to quantify individual differences in orientation and navigation abilities, or the effectiveness of preflight visual. orientation training. Our understanding of the underlying physiology - for example how our sense of place and orientation is neurally coded in three dimensions in the limbic system of the brain - is incomplete. During the 16 months that this human and animal research project has been underway, we have obtained several results that are not only of basic research interest, but which have practical implications for the architecture and layout of spacecraft interiors and for the development of astronaut spatial orientation training countermeasures.

Oman, Charles M.↗

Sputter erosion and deposition in the discharge chamber of a small mercury ion thruster

A 5 cm diameter mercury ion thruster similar to one tested for 9715 hours was operated approximately 400 hrs each at discharge voltages of 36.6, 39.6, and 42.6 V, with corresponding discharge propellant utilizations of 58, 68, and 70 percent. The observed sputter erosion rates of the internal thruster parts and the anode weight gain rate all rose rapidly with discharge voltage and were roughly in the ratio of 1:3:5 for the three voltages. The combined weight loss of the internal thruster parts nearly balanced the anode weight gain. Hg(+2) ion apparently caused most of the observed erosion.

Power, J. L.↗

Sputter erosion and deposition in the discharge chamber of a small mercury ion thruster

A 5-cm diameter mercury ion thruster similar to one tested for 9715 hours was operated approximately 400 hrs each at discharge voltages of 36.6, 39.6, and 42.6 V, with corresponding discharge propellant utilizations of 58, 68, and 70 percent. The observed sputter erosion rates of the internal thruster parts and the anode weight gain rate all rose rapidly with discharge voltage and were roughly in the ratio of 1:3:5 for the three voltages. The combined weight loss of the internal thruster parts nearly balanced the anode weight gain. Hg+2 ions apparently caused most of the observed erosion.

Power, J. L.↗

Further observations of the pulsating X-ray source Cygnus X-1 from Uhuru.

Since the discovery of the pulsations from the X-ray source Cygnus X-1 more data from Uhuru have been analyzed. The conclusions reached about the temporal behavior of the source are described. Large fluctuations of intensity exist on all observed time scales ranging from 50 msec to 10 sec containing up to 50 per cent of the power. Periodic pulse trains with periods from 0.3 sec to over 10 sec exist containing 10-25 per cent of the power; however, they persist only for several seconds or several tens of seconds. No single period is consistently present. This behavior is shown to reconcile the apparently contradictory results obtained by other observers. The energy spectrum of the source is best fitted by a power law, but with great variability in the spectral index and with an excess of flux at higher energies.

Schreier, E.↗

Long-time creep behavior of the niobium alloy C-103

The creep behavior of C-103 was studied as a function of stress, temperature, and grain size for test times to 19000 hr. Over the temperature range 827 to 1204 C and the stress range 6.89 to 138 MPa, only tertiary (accelerating) creep was observed. The creep strain epsilon can be related to time t by an exponential relation epsilon = epsilon(0) + K e raised to power (st) - 1), where epsilon (0) is initial creep strain, K is the tertiary creep strain parameter, and s is the tertiary creep rate parameter. The observed stress exponent 2.87 is similar to the three power law generally observed for secondary (linear) creep of Class I solid solutions. The apparent activation energy 374 kj/g mol is close to that observed for self diffusion of pure niobium. The initial tertiary creep rate was slightly faster for fine grained than for coarse-grained material. The strain parameter K can be expressed as a combination of power functions of stress and grain size and an exponential function of temperature. Strain time curves generated by using calculated values for K and s showed reasonable agreement with observed curves to strains of at least 4 percent. The time to 1 percent strain was related to stress, temperature, and grain size in a similar manner as the initial tertiary creep rate.

Titran, R. H.↗